Ordering number : E*NA0896 LV7150V Bi-CMOS IC Switch for the Wideband Video Signal (with LPF) Overview The LV7150V is switch for the wideband video signal. It has the two input switches by three channels. It built in the 6MHz/12MHz/30MHz-LPF. It is the best for the filter to remove the digital clock noise of the Component or RGB Analog video signal before the A/D converter. It can correspond to the full HD signal because it provides the flat frequency response to 60MHz. Functions • Two input switches × three channels • Component and RGB signal inputs • Flat frequency response to 60MHz (Bypass filter) • 6MHz/12MHz/30MHz-LPF Specifications Maximum Ratings at Ta = 25°C Parameter Maximum Supply voltage Allowable power dissipation Symbol Conditions VCC max Pd max Ratings Unit 6 Ta≤75°C Mounted on a specified board * 300 V mW Operating temperature Topr -20 to +75 °C Storage temperature Tstg -40 to +125 °C Note *: Mounted on a specified board: 114.3mm×76.1mm×1.6mm glass epoxy Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. 72507 TI IM No.A0896-1/5 LV7150V Recommended Operating Conditions at Ta = 25°C Parameter Symbol Recommended Supply voltage Conditions Ratings Unit VCC Operating Supply voltage Range VCC opg 5 V 4.75 to 5.25 V Electrical Characteristics at Ta = 25°C, VCC = 5.0V Parameter Input signal Input Point Signal Freq Out Mag Ratings Test Condition Point min typ unit max VCC Supply Current & Internal reference regulator VCC Supply Current At non-signal, The current V3 34 42 mA 2.8 3.0 3.2 V -0.5 -0.2 0.0 dB -1.0 0.0 1.0 dB -3.0 0.0 1.0 dB -30.0 -20.0 dB 0.0 1.0 dB -30.0 -20.0 dB -1.0 0.0 1.0 dB -3.5 -1.0 1.5 dB -45.0 -33.0 dB -60.0 -50.0 dB -60.0 -55.0 dB flows to 3pin Regulator voltage T16 value The voltage of 16pin Voltage Gain Voltage Gain Py,Pb,Pr,R,G,B Py/Pb/Pr R/G/B T1A T2A T4A T5A SIG2 100k 300mVpp T7A T8A T15 Output gain to input, LPF- T13 ON/OFF is selected T11 Frequency response Frequency response 1 at LPF-OFF Frequency response 2 at 6MHz_LPF Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B Frequency response 3 at 6MHz _LPF Frequency response 4 at 12MHz_LPF Frequency response 5 at 12MHz_LPF Frequency response 6 at 30MHz_LPF Frequency response 7 at 30MHz_LPF Frequency response 8 at 30MHz_LPF Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A 60M 100k 6M 100k 13.5M 100k 12M 100k 27M 100k 20M 100k 30M 100k 75M 100k 300mVpp 300mVpp T15 LPF-OFF is selected, T13 Output Gain difference T11 between 100kHz and 60MHz T15 LPF-ON is selected, T13 Output Gain difference T11 between 100kHz and 6MHz T15 300mVpp T13 T11 300mVpp 300mVpp 300mVpp 300mVpp 300mVpp LPF-ON is selected, Output Gain difference between 100kHz and 13.5MHz T15 LPF-ON is selected, T13 Output Gain difference T11 between 100kHz and 12MHz T15 LPF-ON is selected, T13 Output Gain difference T11 between 100kHz and 27MHz T15 LPF-ON is selected, T13 Output Gain difference T11 between 100kHz and 20MHz T15 LPF-ON is selected, T13 Output Gain difference T11 between 100kHz and 30MHz T15 LPF-ON is selected, T13 Output Gain difference T11 between 100kHz and 75MHz -3.0 S/N Compared with Py S/N R at 30MHz_LPF G B T1A T2A T4A T5A SIG1 T7A T8A 30M 100k T15 650mVpp T13 T11 30MHzLPF-ON is selected, S/N of the band between 100kHz and 30MHz, S/N is shown with dB Crosstalk Crosstalk Py/Pb/Pr R/G/B T1A T2A T4A T5A T7A T8A SIG2 4M 700mVpp T15 LPF-ON/OFF is selected, Ratio T13 at level of non-selection output T11 and selection output Continued on next page. No.A0896-2/5 LV7150V Continued from preceding page. Parameter Input signal Input Point Signal Freq Out Mag Ratings Test Condition Point min typ unit max Group Delay Group Delay 1 Py/Pb/Pr at LPF-OFF R/G/B Group Delay 2 Py/Pb/Pr at LPF-ON R/G/B Group Delay 3 Py/Pb/Pr at LPF-ON R/G/B Group Delay 4 Py/Pb/Pr at LPF-ON R/G/B T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A 60M 100k 6M 100k 12M 100k 30M 100k 300mVpp T15 LPF-OFF is selected T13 f=60MHz/100kHz 0.5 2.0 ns 40.0 70.0 ns 20.0 40.0 ns 10.0 20.0 ns T11 300mVpp T15 6M_LPF-ON is selected T13 f=6MHz/100kHz T11 300mVpp T15 12M_LPF-ON is selected T13 f=12MHz/100kHz T11 300mVpp T15 30MHz_LPF-ON is selected T13 f=30MHz/100kHz T11 Package Dimensions unit : mm (typ) 3178B 5.2 0.5 6.4 9 4.4 16 1 8 0.65 0.15 (0.33) 0.1 (1.3) 1.5max 0.22 SANYO : SSOP16(225mil) Pin Control Table Pin Control Table SW No. Pin No. SW function name SW1 Pin12 CLAMP/BIAS_CTL SW2 Pin10 Filter_CTL1 SW3 Pin9 Filter_CTL2 SW4 Pin14 Input_Select_CTL Input Control Table CLAMP/BIAS_CTL Mode selected Low(0 to 0.7V) CLAMP_ON(Component_Mode) High(2.3V to VCC) BIAS_ON(RGB_Mode) No.A0896-3/5 LV7150V Filter Control Table Filter_CTL1 Filter_CTL2 Mode selected Low(0 to 0.7V) Low(0 to 0.7V) 6M_LPF_ON Low(0 to 0.7V) High(2.3V to VCC) 12M_LPF_ON High(2.3V to VCC) Low(0 to 0.7V) 30M_LPF_ON High(2.3V to VCC) High(2.3V to VCC) LPF_Through_ON Input Select Control Table Input_Select_CTL Mode selected Low(0 to 0.7V) CH1_select High(2.3V to VCC) CH2_select Block Diagram Pr/R_IN1 Pr/R_IN2 1µF + 1µF + 1 2 BIAS 100k Ω SW4: Input_Select _CTL VREG_3V 47µF + Throgh 6MHz LPF BIAS 100kΩ 16 12MHz LPF BUF 15 10µF + Pr/R_OUT SW2&SW3 : Filter_CTL 30MHz LPF VCC 3 14 SW4:Input_Select_CTL Throgh Py/G_ IN1 Py/G_ IN2 1µF + 1µF + 6MHz LPF CLAMP 4 BUF BIAS 100k Ω SW1: CLP/BIAS_ CTL SW4: Input_Select _CTL CLAMP 5 BIAS 100k Ω 12MHz LPF SW1: CLP/BIAS_ CTL Pb/B_IN1 Pb/B_IN2 10µF Py/G_ OUT + SW2&SW3 : Filter_CTL 30MHz LPF 12 SW1:CLP/BIAS_CTL Throgh 6MHz LPF GND 13 6 12MHz LPF BUF 11 10µF Pb/B_OUT + SW2&SW3 : Filter_CTL 30MHz LPF 1µF + 1µF + 7 8 BIAS 100k Ω BIAS 100kΩ SW4: Input_Select _CTL 10 SW2:Filter_CTL1 9 SW3:Filter_CTL2 No.A0896-4/5 LV7150V SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of July, 2007. Specifications and information herein are subject to change without notice. PS No.A0896-5/5