74V1G86 SINGLE EXCLUSIVE OR GATE ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 4.8ns (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 1µA(MAX.) at TA=25°C HIGH NOISE IMMUNITY: VNIH = VNIL = 28% VCC (MIN.) POWER DOWN PROTECTION ON INPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 8mA (MIN) at VCC = 4.5V BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC(OPR) = 2V to 5.5V IMPROVED LATCH-UP IMMUNITY DESCRIPTION The 74V1G86 is an advanced high-speed CMOS SINGLE EXCLUSIVE OR GATE fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. SOT23-5L SOT323-5L ORDER CODES PACKAGE T&R SOT23-5L SOT323-5L 74V1G86STR 74V1G86CTR Power down protection is provided on all inputs and 0 to 7V can be accepted on inputs with no regard to the supply voltage. This device can be used to interface 5V to 3V. PIN CONNECTION AND IEC LOGIC SYMBOLS April 2004 1/9 74V1G86 INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN N° SYMBOL 1 2 4 3 1A 1B 1Y GND VCC 5 NAME AND FUNCTION Data Input Data Input Data Output Ground (0V) Positive Supply Voltage TRUTH TABLE A B Y L L H H L H L H L H H L ABSOLUTE MAXIMUM RATINGS Symbol Value Unit Supply Voltage -0.5 to +7.0 V VI DC Input Voltage -0.5 to +7.0 V VO DC Output Voltage IIK DC Input Diode Current -0.5 to VCC + 0.5 - 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 25 mA VCC Parameter ICC or IGND DC VCC or Ground Current Tstg Storage Temperature TL Lead Temperature (10 sec) V ± 50 mA -65 to +150 °C 260 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage Unit 2 to 5.5 V VI Input Voltage 0 to 5.5 V VO Output Voltage 0 to VCC V Top Operating Temperature -55 to 125 °C 0 to 100 0 to 20 ns/V ns/V dt/dv Input Rise and Fall Time (note 1) (VCC = 3.3 ± 0.3V) (VCC = 5.0 ± 0.5V) 1) VIN from 30% to 70% of VCC 2/9 Value 74V1G86 DC SPECIFICATIONS Test Condition Symbol VIH VIL VOH VOL II ICC Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage Input Leakage Current Quiescent Supply Current Value TA = 25°C VCC (V) Min. 2.0 3.0 to 5.5 2.0 3.0 to 5.5 Typ. Max. -40 to 85°C -55 to 125°C Min. Min. Max. 1.5 1.5 1.5 0.7VCC 0.7VCC 0.7VCC Max. V 0.5 0.5 0.5 0.3VCC 0.3VCC 0.3VCC 2.0 IO=-50 µA 1.9 2.0 1.9 1.9 3.0 IO=-50 µA 2.9 3.0 2.9 2.9 4.5 IO=-50 µA 4.4 4.5 3.0 IO=-4 mA 2.58 4.5 IO=-8 mA 3.94 2.0 IO=50 µA 0.0 0.1 0.1 0.1 3.0 IO=50 µA 0.0 0.1 0.1 0.1 4.5 IO=50 µA 0.0 0.1 0.1 0.1 4.4 4.4 2.48 2.4 3.8 Unit V V 3.7 V 3.0 IO=4 mA 0.36 0.44 0.55 4.5 IO=8 mA 0.36 0.44 0.55 0 to 5.5 VI = 5.5V or GND ± 0.1 ±1 ±1 µA 5.5 VI = VCC or GND 1 10 20 µA AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3ns) Test Condition Symbol Parameter tPLH tPHL Propagation Delay Time VCC (V) CL (pF) Value TA = 25°C Min. Typ. -40 to 85°C -55 to 125°C Max. Min. Max. Min. Max. (*) 15 6.6 9.5 1.0 11.0 1.0 12.5 (*) 3.3 50 7.3 10.5 1.0 12.0 1.0 13.5 5.0(**) 15 4.8 6.8 1.0 8.0 1.0 9.0 5.0(**) 50 5.3 7.5 1.0 9.0 1.0 10.0 3.3 Unit ns (*) Voltage range is 3.3V ± 0.3V (**) Voltage range is 5.0V ± 0.5V CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter Value TA = 25°C Min. Typ. Max. 10 CIN Input Capacitance 4 CPD Power Dissipation Capacitance (note 1) 12 -40 to 85°C -55 to 125°C Min. Min. Max. 10 Unit Max. 10 pF pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC 3/9 74V1G86 TEST CIRCUIT CL = 15/50pF or equivalent (includes jig and probe capacitance) RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM: PROPAGATION DELAY (f=1MHz; 50% duty cycle) 4/9 74V1G86 SOT23-5L MECHANICAL DATA mm. mils DIM. MIN. TYP MAX. MIN. TYP. MAX. A 0.90 1.45 35.4 57.1 A1 0.00 0.10 0.0 3.9 A2 0.90 1.30 35.4 51.2 b 0.35 0.50 13.7 19.7 C 0.09 0.20 3.5 7.8 D 2.80 3.00 110.2 118.1 E 1.50 1.75 59.0 68.8 e 0.95 37.4 H 2.60 3.00 102.3 118.1 L 0.10 0.60 3.9 23.6 . 7049676C 5/9 74V1G86 SOT323-5L MECHANICAL DATA mm. mils DIM. MIN. MAX. MIN. TYP. MAX. A 0.80 1.10 31.5 43.3 A1 0.00 0.10 0.0 3.9 A2 0.80 1.00 31.5 39.4 b 0.15 0.30 5.9 11.8 C 0.10 0.18 3.9 7.1 D 1.80 2.20 70.9 86.6 E 1.80 2.40 70.9 94.5 E1 1.15 1.35 45.3 53.1 e 0 .65 25.6 e1 1.3 51.2 L 6/9 TYP 0.10 0.30 3.9 11.8 74V1G86 Tape & Reel SOT23-xL MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. 180 13.0 7.086 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 MAX. 0.504 0.512 14.4 0.519 0.567 Ao 3.13 3.23 3.33 0.123 0.127 0.131 Bo 3.07 3.17 3.27 0.120 0.124 0.128 Ko 1.27 1.37 1.47 0.050 0.054 0.0.58 Po 3.9 4.0 4.1 0.153 0.157 0.161 P 3.9 4.0 4.1 0.153 0.157 0.161 7/9 74V1G86 Tape & Reel SOT323-xL MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 175 180 185 6.889 7.086 7.283 C 12.8 13 13.2 0.504 0.512 0.519 D 20.2 N 59.5 0.795 60 T 8/9 60.5 2.362 14.4 0.567 Ao 2.25 0.088 Bo 2.7 0.106 Ko 1.2 0.047 Po 3.9 4 4.1 0.153 0.157 0.161 P 3.8 4 4.2 0.149 0.157 0.165 74V1G86 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 9/9