STMICROELECTRONICS M27W101

M27W101
1 Mbit (128Kb x8) Low Voltage UV EPROM and OTP EPROM
Features
■
2.7V to 3.6V Low Voltage in Read Operation
■
Access Time:
– 70 ns at VCC = 3.0V to 3.6V
– 80 ns at VCC = 2.7V to 3.6V
■
Pin compatible with M27C1001
■
Low Power Consumption:
– Active Current: 15 mA at 5 MHz
– Standby Current: 15 µA
■
Programming Time: 100 µs/byte
■
High Reliability CMOS Technology
– 2,000V ESD Protection
– 200 mA Latch-up Protection Immunity
■
■
32
PLCC32 (K)
1
FDIP32W (F)
32
Electronic Signature
– Manufacturer Code: 20h
– Device Code: 05h
TSOP32 (N)
8 x 20 mm
1
PDIP32 (B)
ECOPACK® packages available
April 2006
Rev 3
1/23
www.st.com
1
Contents
M27W101
Contents
1
Summary description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2
Device description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1
Read mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2
Standby mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.3
Two-line output control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4
System considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.5
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.6
Presto II programming algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.7
Program Inhibit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.8
Program Verify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.9
Electronic Signature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.10
Erasure operation (applies to UV EPROM) . . . . . . . . . . . . . . . . . . . . . . . 11
3
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4
DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.1
32-pin Ceramic Frit-seal DIP, with round window (FDIP32WA) . . . . . . . . 17
5.2
32-pin Plastic DIP, 600 mils width (PDIP32) . . . . . . . . . . . . . . . . . . . . . . . 18
5.3
32-lead Rectangular Plastic Leaded Chip Carrier (PLCC32) . . . . . . . . . . 19
5.4
32-lead Plastic Thin Small Outline, 8x20 mm (TSOP32) . . . . . . . . . . . . . 20
6
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2/23
M27W101
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Signal descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Electronic Signature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Read Mode DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Programming Mode DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
AC Measurement Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Read Mode AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Programming Mode AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
FDIP32WA package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
PDIP32 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
PLCC32 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
TSOP32 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Ordering Information Scheme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3/23
List of figures
M27W101
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
4/23
Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
DIP Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
LCC Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
TSOP Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Programming Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
AC Testing Input Output Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
AC Testing Load Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Read Mode AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Programming and Verify Modes AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
FDIP32WA package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
PDIP32 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
PLCC32 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
TSOP32 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
M27W101
1
Summary description
Summary description
The M27W101 is a low voltage 1 Mbit EPROM offered in two range UV (ultra violet erase)
and OTP (one time programmable). It is ideally suited for microprocessor systems requiring
large data or program storage and is organized as 131,072 by 8 bits.
The M27W101 operates in the read mode with a supply voltage as low as 2.7V at –40° to
85° C temperature range.
The decrease in operating power allows either a reduction of the size of the battery or an
increase in the time between battery recharges.
The FDIP32W (window ceramic frit-seal package) has a transparent lid which allows the
user to expose the chip to ultraviolet light to erase the bit pattern. A new pattern can then be
written to the device by following the programming procedure.
For application where the content is programmed only one time and erasure is not required,
the M27W101 is offered in PDIP32, PLCC32 and TSOP32 (8 x 20 mm) packages.
In order to meet environmental requirements, ST offers the M27W101 in ECOPACK®
packages. ECOPACK packages are Lead-free. The category of second Level Interconnect
is marked on the package and on the inner box label, in compliance with JEDEC Standard
JESD97. The maximum ratings related to soldering conditions are also marked on the inner
box label.
ECOPACK is an ST trademark. ECOPACK® specifications are available at: www.st.com.
See Figure 1: Logic diagram and Table 1: Signal descriptions for a brief overview of the
signals connected to this device.
Figure 1.
Logic diagram
VCC
VPP
17
8
A0-A16
P
Q0-Q7
M27W101
E
G
VSS
AI01587
5/23
Summary description
Table 1.
M27W101
Signal descriptions
Signal
Description
A0-A16
Address Inputs
Q0-Q7
Data Outputs
E
Chip Enable
G
Output Enable
P
Program
VPP
Program Supply
VCC
Supply Voltage
VSS
Ground
NC
Not Connected Internally
Figure 2.
DIP Connections
VPP
A16
A15
A12
A7
A6
A5
A4
A3
A2
A1
A0
Q0
Q1
Q2
VSS
1
32
2
31
3
30
4
29
5
28
6
27
7
26
8
25
M27W101
9
24
10
23
11
22
12
21
13
20
14
19
15
18
16
17
AI02674
6/23
VCC
P
NC
A14
A13
A8
A9
A11
G
A10
E
Q7
Q6
Q5
Q4
Q3
M27W101
Summary description
LCC Connections
A12
A15
A16
VPP
VCC
P
NC
Figure 3.
1 32
A7
A6
A5
A4
A3
A2
A1
A0
Q0
M27W101
9
25
A14
A13
A8
A9
A11
G
A10
E
Q7
VSS
Q3
Q4
Q5
Q6
Q1
Q2
17
AI01588
Figure 4.
TSOP Connections
A11
A9
A8
A13
A14
NC
P
VCC
VPP
A16
A15
A12
A7
A6
A5
A4
1
8
9
16
32
M27W101
(Normal)
25
24
17
G
A10
E
Q7
Q6
Q5
Q4
Q3
VSS
Q2
Q1
Q0
A0
A1
A2
A3
AI01589
7/23
Device description
2
M27W101
Device description
The operating modes of the M27W101 are listed in the Operating Modes table. A single
power supply is required in the read mode. All inputs are TTL levels except for VPP and 12V
on A9 for Electronic Signature.
Table 2.
Operating modes
Mode
E
G
P
A9
VPP
Q7-Q0
Read
VIL
VIL
X
X
VCC or VSS
Data Out
Output Disable
VIL
VIH
X
X
VCC or VSS
Hi-Z
Program
VIL
VIH
VIL Pulse
X
VPP
Data In
Verify
VIL
VIL
VIH
X
VPP
Data Out
Program Inhibit
VIH
X
X
X
VPP
Hi-Z
Standby
VIH
X
X
X
VCC or VSS
Hi-Z
Electronic Signature
VIL
VIL
VIH
VID
VCC
Codes
Note:
X = VIH or VIL, VID = 12V ± 0.5V.
2.1
Read mode
The M27W101 has two control functions, both of which must be logically active in order to
obtain data at the outputs. Chip Enable (E) is the power control and should be used for
device selection. Output Enable (G) is the output control and should be used to gate data to
the output pins, independent of device selection. Assuming that the addresses are stable,
the address access time (tAVQV) is equal to the delay from E to output (tELQV). Data is
available at the output after a delay of tGLQV from the falling edge of G, assuming that E has
been low and the addresses have been stable for at least tAVQV-tGLQV.
2.2
Standby mode
The M27W101 has a standby mode which reduces the supply current from 15mA to 15µA
with low voltage operation VCC ≤ 3.6V, see Read Mode DC Characteristics table for details.
The M27W101 is placed in the standby mode by applying a CMOS high signal to the E
input. When in the standby mode, the outputs are in a high impedance state, independent of
the G input.
2.3
Two-line output control
Because EPROMs are usually used in larger memory arrays, this product features a 2-line
control function which accommodates the use of multiple memory connection.
The two line control function allows:
8/23
●
the lowest possible memory power dissipation,
●
complete assurance that output bus contention will not occur.
M27W101
Device description
For the most efficient use of these two control lines, E should be decoded and used as the
primary device selecting function, while G should be made a common connection to all
devices in the array and connected to the READ line from the system control bus. This
ensures that all deselected memory devices are in their low power standby mode and that
the output pins are only active when data is required from a particular memory device.
2.4
System considerations
The power switching characteristics of Advanced CMOS EPROMs require careful
decoupling of the devices. The supply current, ICC, has three segments that are of interest to
the system designer: the standby current level, the active current level, and transient current
peaks that are produced by the falling and rising edges of E. The magnitude of the transient
current peaks is dependent on the capacitive and inductive loading of the device at the
output. The associated transient voltage peaks can be suppressed by complying with the
two line output control and by properly selected decoupling capacitors. It is recommended
that a 0.1µF ceramic capacitor be used on every device between VCC and VSS. This should
be a high frequency capacitor of low inherent inductance and should be placed as close to
the device as possible. In addition, a 4.7µF bulk electrolytic capacitor should be used
between VCC and VSS for every eight devices. The bulk capacitor should be located near the
power supply connection point. The purpose of the bulk capacitor is to overcome the voltage
drop caused by the inductive effects of PCB traces.
2.5
Programming
The M27W101 has been designed to be fully compatible with the M27C1001 and has the
same electronic signature. As a result the M27W101 can be programmed as the M27C1001
on the same programming equipment applying 12.75V on VPP and 6.25V on VCC using the
same PRESTO II algorithm. When delivered (and after each ‘1’s erasure for UV EPROM), all
bits of the M27W101 are in the '1' state. Data is introduced by selectively programming '0's
into the desired bit locations. Although only '0's will be programmed, both '1's and '0's can be
present in the data word. The only way to change a ‘0’ to a ‘1’ is by die exposure to
ultraviolet light (UV EPROM). The M27W101 is in the programming mode when VPP input is
at 12.75V, E is at VIL and P is pulsed to VIL. The data to be programmed is applied to 8 bits
in parallel to the data output pins. The levels required for the address and data inputs are
TTL. VCC is specified to be 6.25V ± 0.25V.
2.6
Presto II programming algorithm
Presto II Programming Algorithm allows the whole array to be programmed, with a
guaranteed margin, in a typical time of 13 seconds. Programming with Presto II involves in
applying a sequence of 100µs program pulses to each byte until a correct verify occurs (see
Figure 5). During programming and verify operation, a Margin Mode circuit is automatically
activated in order to guarantee that each cell is programmed with enough margin. No
overprogram pulse is applied since the verify in Margin Mode at VCC much higher than 3.6V,
provides necessary margin to each programmed cell.
9/23
Device description
Figure 5.
M27W101
Programming Flowchart
VCC = 6.25V, VPP = 12.75V
n=0
P = 100µs Pulse
NO
++n
= 25
YES
FAIL
NO
VERIFY
++ Addr
YES
Last
Addr
NO
YES
CHECK ALL BYTES
1st: VCC = 5V
2nd: VCC = 2.7V
AI00715D
2.7
Program Inhibit
Programming of multiple M27W101s in parallel with different data is also easily
accomplished. Except for E, all like inputs including G of the parallel M27W101 may be
common. A TTL low level pulse applied to a M27W101's P input, with E low and VPP at
12.75V, will program that M27W101. A high level E input inhibits the other M27W101s from
being programmed.
2.8
Program Verify
A verify (read) should be performed on the programmed bits to determine that they were
correctly programmed. The verify is accomplished with E and G at VIL, P at VIH, VPP at
12.75V and VCC at 6.25V.
2.9
Electronic Signature
The Electronic Signature (ES) mode allows the reading out of a binary code from an
EPROM that will identify its manufacturer and type. This mode is intended for use by
programming equipment to automatically match the device to be programmed with its
corresponding programming algorithm. The ES mode is functional in the 25°C ± 5°C
ambient temperature range that is required when programming the M27W101. To activate
the ES mode, the programming equipment must force 11.5V to 12.5V on address line A9 of
the M27W101, with VPP = VCC = 5V. Two identifier bytes may then be sequenced from the
device outputs by toggling address line A0 from VIL to VIH. All other address lines must be
held at VIL during Electronic Signature mode.
10/23
M27W101
Device description
Byte 0 (A0 = VIL) represents the manufacturer code and byte 1 (A0 = VIH) the device
identifier code. For the STMicroelectronics M27W101, these two identifier bytes are given in
Table Table 3 and can be read-out on outputs Q7 to Q0.
Note that the M27W101 and M27C1001 have the same identifier byte.
Table 3.
Electronic Signature
Identifier
2.10
A0
Q7
Q6
Q5
Q4
Q3
Q2
Q1
Q0
Hex Data
Manufacturer’s Code
VIL
0
0
1
0
0
0
0
0
20h
Device Code
VIH
0
0
0
0
0
1
0
1
05h
Erasure operation (applies to UV EPROM)
The erasure characteristics of the M27W101 is such that erasure begins when the cells are
exposed to light with wavelengths shorter than approximately 4000 Å. It should be noted
that sunlight and some type of fluorescent lamps have wavelengths in the 3000-4000 Å
range. Research shows that constant exposure to room level fluorescent lighting could
erase a typical M27W101 in about 3 years, while it would take approximately 1 week to
cause erasure when exposed to direct sunlight. If the M27W101 is to be exposed to these
types of lighting conditions for extended periods of time, it is suggested that opaque labels
be put over the M27W101 window to prevent unintentional erasure. The recommended
erasure procedure for the M27W101 is exposure to short wave ultraviolet light which has a
wavelength of 2537 Å. The integrated dose (i.e. UV intensity x exposure time) for erasure
should be a minimum of 15 W-sec/cm2. The erasure time with this dosage is approximately
15 to 20 minutes using an ultraviolet lamp with 12000 µW/cm2 power rating. The M27W101
should be placed within 2.5 cm (1 inch) of the lamp tubes during the erasure. Some lamps
have a filter on their tubes which should be removed before erasure.
11/23
Maximum ratings
3
M27W101
Maximum ratings
Table 4.
Absolute Maximum Ratings (1)
Symbol
Value
Unit
Ambient Operating Temperature (2)
–40 to 125
°C
TBIAS
Temperature Under Bias
–50 to 125
°C
TSTG
Storage Temperature
–65 to 150
°C
VIO (3)
Input or Output Voltage (except A9)
–2 to 7
V
Supply Voltage
–2 to 7
V
–2 to 13.5
V
–2 to 14
V
TA
VCC
VA9
(3)
VPP
Parameter
A9 Voltage
Program Supply Voltage
1. Except for the rating "Operating Temperature Range", stresses above those listed in the Table "Absolute
Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and
operation of the device at these or any other conditions above those indicated in the Operating sections of
this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods
may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality
documents.
2. Depends on range.
3. Minimum DC voltage on Input or Output is –0.5V with possible undershoot to –2.0V for a period less than
20ns. Maximum DC voltage on Output is VCC +0.5V with possible overshoot to VCC +2V for a period less
than 20ns.
12/23
M27W101
4
DC and AC parameters
DC and AC parameters
TA = –40 to 85°C; VCC = 2.7V to 3.6V; VPP = VCC
Table 5.
Symbol
Read Mode DC Characteristics (1)
Parameter
ILI
Input Leakage Current
ILO
Output Leakage Current
ICC
Supply Current
ICC1
Supply Current (Standby) TTL
ICC2
Supply Current (Standby)
CMOS
IPP
Program Current
VIL
Input Low Voltage
VIH (2)
Input High Voltage
VOL
Output Low Voltage
VOH
Output High Voltage TTL
Test Condition
Min.
Max.
Unit
0V ≤ VIN ≤ VCC
±10
µA
0V ≤ VOUT ≤ VCC
±10
µA
E = VIL, G = VIL, IOUT = 0mA,
f = 5MHz, VCC ≤ 3.6V
15
mA
E = VIH
1
mA
E > VCC – 0.2V, VCC ≤ 3.6V
15
µA
VPP = VCC
10
µA
0.2VCC
V
–0.3
0.7VCC VCC + 0.5
IOL = 2.1mA
0.4
IOH = –400µA
2.4
V
V
V
1. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP.
2. Maximum DC voltage on Output is VCC +0.5V.
TA = 25 °C; VCC = 6.25V ± 0.25V; VPP = 12.75V ± 0.25V
Table 6.
Symbol
Programming Mode DC Characteristics (1)
Parameter
Test Condition
Min
0 ≤ VIN ≤ VCC
Max
Unit
±10
µA
50
mA
50
mA
ILI
Input Leakage Current
ICC
Supply Current
IPP
Program Current
VIL
Input Low Voltage
–0.3
0.8
V
VIH
Input High Voltage
2.0
VCC + 0.5
V
VOL
Output Low Voltage
0.4
V
VOH
Output High Voltage TTL
VID
A9 Voltage
E = VIL
IOL = 2.1mA
IOH = –400µA
2.4
11.5
V
12.5
V
1. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP.
13/23
DC and AC parameters
Table 7.
M27W101
AC Measurement Conditions
Parameter
High Speed
Standard
Input Rise and Fall Times
≤ 10ns
≤ 20ns
Input Pulse Voltages
0 to 3V
0.4V to 2.4V
1.5V
0.8V and 2V
Input and Output Timing Ref. Voltages
TA = 25 °C, f = 1 MHz
Table 8.
Symbol
CIN
COUT
Capacitance (1)
Parameter
Test Condition
Max.
Unit
VIN = 0V
6
pF
VOUT = 0V
12
pF
Input Capacitance
Output Capacitance
1. Sampled only, not 100% tested.
Figure 6.
AC Testing Input Output Waveform
High Speed
3V
1.5V
0V
Standard
2.4V
2.0V
0.8V
0.4V
AI01822
Figure 7.
AC Testing Load Circuit
1.3V
1N914
3.3kΩ
DEVICE
UNDER
TEST
OUT
CL
CL = 30pF for High Speed
CL = 100pF for Standard
CL includes JIG capacitance
14/23
AI01823B
Min.
M27W101
DC and AC parameters
TA = –40 to 85°C; VCC = 2.7V to 3.6V; VPP = VCC
Table 9.
Read Mode AC Characteristics (1)
-100
(-120, -150
and -200)
-80 (2)
Symbol
Alt
Parameter
Test
Condition
Unit
VCC = 3.0V
to 3.6V
Min.
Max.
VCC = 2.7V to 3.6V
Min.
Max.
Min.
Max.
E = VIL,
G = VIL
70
80
100
ns
Chip Enable Low to Output
Valid
G = VIL
70
80
100
ns
tOE
Output Enable Low to Output
Valid
E = VIL
40
50
60
ns
tEHQZ (3)
tDF
Chip Enable High to Output HiZ
G = VIL
0
40
0
50
0
60
ns
tGHQZ (3)
tDF
Output Enable High to Output
Hi-Z
E = VIL
0
40
0
50
0
60
ns
tAXQX
tOH
Address Transition to Output
Transition
E = VIL,
G = VIL
0
tAVQV
tACC Address Valid to Output Valid
tELQV
tCE
tGLQV
0
0
ns
1. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP.
2. Speed obtained with High Speed measurement conditions.
3. Sampled only, not 100% tested.
TA = 25 °C; VCC = 6.25V ± 0.25V; VPP = 12.75V ± 0.25V
Table 10.
Programming Mode AC Characteristics (1)
Symbol
Alt
tAVPL
tAS
Address Valid to Program Low
2
µs
tQVPL
tDS
Input Valid to Program Low
2
µs
tVPHPL
tVPS
VPP High to Program Low
2
µs
tVCHPL
tVCS
VCC High to Program Low
2
µs
tELPL
tCES
Chip Enable Low to Program Low
2
µs
tPLPH
tPW
Program Pulse Width
95
tPHQX
tDH
Program High to Input Transition
2
µs
tQXGL
tOES
Input Transition to Output Enable Low
2
µs
tGLQV
tOE
Output Enable Low to Output Valid
tDFP
Output Enable High to Output Hi-Z
0
tAH
Output Enable High to Address Transition
0
tGHQZ
(2)
tGHAX
Parameter
Test Condition
Min.
Max.
105
Unit
µs
100
ns
130
ns
ns
1. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP.
2. Sampled only, not 100% tested.
15/23
DC and AC parameters
Figure 8.
M27W101
Read Mode AC Waveforms
VALID
A0-A16
VALID
tAVQV
tAXQX
E
tEHQZ
tGLQV
G
tGHQZ
tELQV
Hi-Z
Q0-Q7
AI00713B
Figure 9.
Programming and Verify Modes AC Waveforms
VALID
A0-A16
tAVPL
Q0-Q7
DATA IN
tQVPL
DATA OUT
tPHQX
VPP
tVPHPL
tGLQV
tGHQZ
VCC
tVCHPL
tGHAX
E
tELPL
P
tPLPH
tQXGL
G
PROGRAM
VERIFY
AI00714
16/23
M27W101
Package mechanical data
5
Package mechanical data
5.1
32-pin Ceramic Frit-seal DIP, with round window (FDIP32WA)
Figure 10. FDIP32WA package outline
A2
A3
A1
B1
B
A
L
α
e
eA
D2
C
eB
D
S
N
∅
E1
E
1
FDIPW-a
Table 11.
FDIP32WA package mechanical data
millimeters
inches
Symbol
Min
Typ
A
Max
Min
Typ
5.72
Max
0.225
A1
0.51
1.40
0.020
0.055
A2
3.91
4.57
0.154
0.180
A3
3.89
4.50
0.153
0.177
B
0.41
0.56
0.016
0.022
B1
1.45
0.057
C
0.23
0.30
0.009
0.012
D
41.73
42.04
1.643
1.655
D2
38.10
1.500
e
2.54
0.100
E
15.24
0.600
E1
13.06
eA
13.36
0.514
14.99
0.526
0.590
eB
16.18
18.03
0.637
0.710
L
3.18
4.10
0.125
0.161
N
S
32
1.52
Ø
α
32
2.49
0.060
7.11
4°
0.098
0.280
11°
4°
11°
17/23
Package mechanical data
5.2
M27W101
32-pin Plastic DIP, 600 mils width (PDIP32)
Figure 11. PDIP32 package outline
A2
A1
b1
b
A
L
α
e
eA
c
D2
D
S
N
E1
E
1
PDIP-C
Table 12.
PDIP32 package mechanical data
millimeters
inches
Symbol
Min
Typ
A
A1
Min
Typ
5.080
0.381
A2
Max
0.2000
0.0150
3.912
0.1540
b
0.406
0.559
0.0160
0.0220
b1
1.168
1.372
0.0460
0.0540
c
0.203
0.356
0.0080
0.0140
D
41.402
42.418
1.6300
1.6700
D2
38.100
E
15.240
E1
13.890
1.5000
0.6000
14.248
0.5469
0.5609
e
2.540
0.1000
eA
15.240
0.6000
L
3.175
N
18/23
Max
3.429
0.1250
32
0.1350
32
S
1.650
2.210
0.0650
0.0870
α
0°
15°
0
15°
M27W101
5.3
Package mechanical data
32-lead Rectangular Plastic Leaded Chip Carrier (PLCC32)
Figure 12. PLCC32 package outline
D
D1
A1
A2
1 N
B1
E2
e
E1 E
E3
F
B
0.51 (.020)
E2
1.14 (.045)
A
D3
R
D2
CP
D2
PLCC-A
Table 13.
PLCC32 package mechanical data
millimeters
inches
Symbol
Min
Typ
Max
Min
Typ
Max
A
3.18
3.56
0.125
0.140
A1
1.53
2.41
0.060
0.095
A2
0.38
B
0.33
0.53
0.013
0.021
B1
0.66
0.81
0.026
0.032
0.015
CP
0.10
0.004
D
12.32
12.57
0.485
0.495
D1
11.35
11.51
0.447
0.453
D2
4.78
5.66
0.188
0.223
D3
7.62
0.300
E
14.86
15.11
0.585
0.595
E1
13.89
14.05
0.547
0.553
E2
6.05
6.93
0.238
0.273
E3
10.16
0.400
e
1.27
0.050
F
0.00
0.13
0.000
0.005
R
0.89
0.035
N
32
32
19/23
Package mechanical data
5.4
M27W101
32-lead Plastic Thin Small Outline, 8x20 mm (TSOP32)
Figure 13. TSOP32 package outline
A2
N
1
e
E
B
N/2
A
D1
CP
D
DIE
C
A1
TSOP-a
Table 14.
α
L
TSOP32 package mechanical data
millimeters
inches
Symbol
Min
Typ
A
Min
Typ
1.200
Max
0.0472
A1
0.050
0.150
0.0020
0.0059
A2
0.950
1.050
0.0374
0.0413
B
0.170
0.250
0.0067
0.0098
C
0.100
0.210
0.0039
0.0083
CP
0.100
0.0039
D
19.800
20.200
0.7795
0.7953
D1
18.300
18.500
0.7205
0.7283
e
–
–
–
E
7.900
8.100
0.3110
0.3189
L
0.500
0.700
0.0197
0.0276
N
α
20/23
Max
0.500
32
0°
0.0197
–
32
5°
0°
5°
M27W101
6
Part numbering
Part numbering
Table 15.
Ordering Information Scheme
Example:
M27W101
-80
K
6 TR
Device Type
M27
Supply Voltage
W = 2.7V to 3.6V
Device Function
101 = 1 Mbit (128Kb x8)
Speed
-80 (1) (2) = 80 ns
-100 = 100 ns
Not For New Design (3)
-120 = 120 ns
-150 = 150 ns
-200 = 200 ns
Package
F = FDIP32W (4)
B = PDIP32
K = PLCC32
N = TSOP32: 8 x 20 mm(4)
Temperature Range
6 = –40 to 85 °C
Options
TR = ECOPACK® package, Tape & Reel Packing
1. High Speed, see AC Characteristics section for further information.
2. This speed also guarantees 70ns access time at VCC = 3.0V to 3.6V.
3. These speeds are replaced by the 100ns.
4. Packages option available on request. Please contact STMicroelectronics local Sales Office.
For a list of available options (Speed, Package, etc...) or for further information on any
aspect of this device, please contact the STMicroelectronics Sales Office nearest to you.
21/23
Revision history
7
M27W101
Revision history
Table 16.
22/23
Document revision history
Date
Revision
Changes
25- Jul-1999
1
Initial release.
4-Apr-2000
2
FDIP32W Package Dimension, L Max added (Table 11)
PLCC32 and TSOP32 Package Dimension changed (Table 13 and
Table 14)
0 to 70°C Temperature Range deleted
Programming Time changed
12-Apr-2006
3
Converted to new template. Added ECOPACK® information.
M27W101
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZE REPRESENTATIVE OF ST, ST PRODUCTS ARE NOT DESIGNED,
AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS,
NOR IN PRODUCTS OR SYSTEMS, WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR
SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2006 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
23/23