STMICROELECTRONICS M4Z32

M4Z28-BR00SH
M4Z32-BR00SH
ZEROPOWER® SNAPHAT® (BATTERY)
FEATURES SUMMARY
■ PROVIDES BATTERY BACKUP POWER FOR
NON-VOLATILE ZEROPOWER and
SUPERVISOR DEVICES IN THE 28-PIN
SNAPHAT SOIC PACKAGE
■
REMOVABLE BATTERY AVOIDS HEAT
ASSOCIATED WITH SURFACE-MOUNT
PROCESS
■
SNAPS DIRECTLY ONTO SURFACEMOUNTED SNAPHAT SOIC
■
Figure 1. SNAPHAT Top Package
SNAPHAT (SH)
Battery
CHOICE OF BATTERY CAPACITIES
– M4Z28-BR00SH = 48mAh
– M4Z32-BR00SH = 120mAh
■
KEYED INSERTION TO INSURE PROPER
ASSEMBLY
■
REMOVABLE FOR REPLACEMENT and
PROPER DISPOSAL
■
Pb-FREE PACKAGE
■
AVAILABLE IN TUBES OR TAPE & REEL
March 2003
Rev. 2.5
1/12
M4Z28-BR00SH, M4Z32-BR00SH
TABLE OF CONTENTS
SUMMARY DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Logic Diagram (Figure 2.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Signal Names (Table 1.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
MAXIMUM RATING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Absolute Maximum Ratings (Table 2.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
DC AND AC PARAMETERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Operating and AC Measurement Conditions (Table 3.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
MECHANICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SNAPHAT Insertion/Extraction Forces (Figure 3.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Battery Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
UL Recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Battery Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Battery Discharge Rates (Figure 4.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
DIP Extractor Tool (Figure 5.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PART NUMBERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PACKAGE MECHANICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
REVISION HISTORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2/12
M4Z28-BR00SH, M4Z32-BR00SH
SUMMARY DESCRIPTION
The M4ZXX-BR00SH SNAPHAT® top is a
detachable lithium power source for ST’s nonvolatile ZEROPOWER ® surface-mount SOIC
(MH) package (28-pin).
Figure 2. Logic Diagram
The SNAPHAT top contains a lithium battery and
is designed to be “snapped on” after the SOIC is
surface mounted on the PC board. The two-piece
solution prevents the battery from being exposed
to the high temperatures of the surface mount process.
Table 1. Signal Names
VBAT–
Negative Voltage
VBAT+
Positive Voltage
SNAPHAT
VBAT–
VBAT+
AI02525
3/12
M4Z28-BR00SH, M4Z32-BR00SH
MAXIMUM RATING
Stressing the device above the rating listed in the
“Absolute Maximum Ratings” table may cause
permanent damage to the device. These are
stress ratings only and operation of the device at
these or any other conditions above those indicated in the Operating sections of this specification is
not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device
reliability.
Refer
also
to
the
STMicroelectronics SURE Program and other relevant quality documents.
Table 2. Absolute Maximum Ratings
Symbol
TA
TSTG
Parameter
Value
Unit
Ambient Operating Temperature
–40 to 85
°C
Storage Temperature (VCC Off, Oscillator Off)
–40 to 85
°C
CAUTION: Do NOT wave solder SOIC to avoid damaging SNAPHAT sockets.
DC AND AC PARAMETERS
This section summarizes the operating and measurement conditions, as well as the DC and AC
characteristics of the device. The parameters in
the following DC and AC Characteristic tables are
derived from tests performed under the Measure-
ment Conditions listed in the relevant tables. Designers should check that the operating conditions
in their projects match the measurement conditions when using the quoted parameters.
Table 3. Operating and AC Measurement Conditions
Parameter
M4Z28-BR00SH
M4Z32-BR00SH
Unit
Nominal Battery Voltage (VCC)
2.8
2.8
V
Nominal Battery Capacity
48
120
mAh
Li(CF)
Li(CF)
Battery Chemistry
4/12
M4Z28-BR00SH, M4Z32-BR00SH
MECHANICAL INFORMATION
Electrical connection to the SOIC is made through
two pins that connect to the press fitted sockets at
one end of the SOIC. Critical contact points between the pins and sockets are gold-plated to resist oxidation. Internally, each socket contains six
independent contact fingers to form redundant
connections between the two components. These
sockets were designed to provide high point contact force to provide the lowest possible contact resistance. The SNAPHAT® top also incorporates
four molded-in retaining clips which hold onto the
ends of the SOIC insuring mechanical and electrical connection even under severe mechanical
shock and vibration. The combined SOIC and
SNAPHAT assembly can sustain shock levels in
excess of 100 g without separating. This package
also passes variable frequency testing in accordance with MIL-STD-883, method 2007.2, condition A.
Figure 3 illustrates the affect of repeated insertion
and extraction of the SNAPHAT top to the SOIC.
The force required to extract the SNAPHAT, and
then to re-insert it, reduces each time. After four or
five extractions, the reduction starts to become
unnoticeable and the force required remains at a
fairly constant figure. Typically, though, the
SNAPHAT will only need to be extracted and reinserted once in its lifetime.
Figure 3. SNAPHAT Insertion/Extraction Forces
15
12.5
Average Insertion
Average Extraction
Force (pounds)
10
7.5
5
2.5
0
1
2
3
4
5
6
7
8
9
10
Number of Extractions
AI02526
5/12
M4Z28-BR00SH, M4Z32-BR00SH
Battery Characteristics
Figure 4, page 7 illustrates the lithium coin cell discharge rate for a given load. This demonstrates
the characteristically flat voltage level supplied by
the battery until very near the end of its life. These
discharge levels have been greatly accelerated in
comparison to the normal, actual usage.
Note: These batteries contain no Mercury (Hg),
Cadmium (Cd), or Lead (Pb).
UL Recognition
The M4ZXX-BR00SH has been recognized by Underwriters Laboratories under their Component
Recognition Program and carries U.L. File Number E89556.
Battery Life
For information on Data Retention Life and Battery
Storage Life, please refer to the Application Note
AN1012.
General Notes
ST has conducted experiments using a manual
press which determined that if approximately 60
6/12
pounds of force is applied to the top of the
SNAPHAT®, battery damage and/or die cracks
could be induced. As Figure 3, page 5 specifies,
only an average of less than 13 force-pounds is required for proper insertion. We recommend that no
more than 40 pounds of force be applied during
SNAPHAT insertion.
If a manual press in employed, it is very important
that it be calibrated such that it cannot exceed this
limit.
To remove the SNAPHAT® top for replacement, a
DIP/IC extractor tool should be used (see Figure
5). The SNAPHAT top should be grabbed by the
narrow end to avoid bending the pins.
Caution: To avoid draining battery do NOT place
SNAPHAT pins into conductive foam.
Caution: To avoid damaging SNAPHAT sockets
do NOT wave solder SOIC.
For battery disposal information, see on the web at
www.rayovac.com.
M4Z28-BR00SH, M4Z32-BR00SH
Figure 4. Battery Discharge Rates
LOAD CHARACTERISTICS
3.5
Temp: 20˚C
Voltage (V)
3.0
2.5
BR1225
2.0
15kΩ
30kΩ
100kΩ
1.5
1.0
200 400 600 800 1000 1200 1400 1600 1800 2000
0
Duration (hrs.)
(A)
LOAD CHARACTERISTICS
3.5
Temp: 20˚C
Voltage (V)
3.0
2.5
BR1632
2.0
15kΩ
30kΩ
50kΩ
100kΩ
1.5
1.0
0
1000
2000
3000
4000
Duration (hrs.)
(B)
5000
6000
AI02519
Figure 5. DIP Extractor Tool
AI02527
7/12
M4Z28-BR00SH, M4Z32-BR00SH
PART NUMBERING
Table 4. Ordering Information Scheme
Example:
M4Z
28-BR00
SH
1
TR
Device Type
M4Z
Battery Voltage and Capacity
28-BR00 = BR1225, 3V, 48mAh
32-BR00 = BR1632, 3V, 120mAh
Package
SH = SNAPHAT®
Temperature Range
1 = –40 to 85°C
Shipping Method
blank = Tubes
TR = Tape & Reel
For a list of available options (e.g., Speed, Package) or for further information on any aspect of this device,
please contact the ST Sales Office nearest to you.
8/12
M4Z28-BR00SH, M4Z32-BR00SH
PACKAGE MECHANICAL INFORMATION
Figure 6. SH – 4-pin SNAPHAT Housing for 48mAh Battery Package Outline
A1
eA
A2
A
A3
B
L
eB
D
E
SHZP-A
Note: Drawing is not to scale.
Table 5. SH – 4-pin SNAPHAT Housing for 48mAh Battery Package Mechanical Data
mm
inches
Symb
Typ
Min
A
Max
Typ
Min
9.78
Max
0.385
A1
6.73
7.24
0.265
0.285
A2
6.48
6.99
0.255
0.275
A3
0.38
0.015
B
0.46
0.56
0.018
0.022
D
21.21
21.84
0.835
0.860
E
14.22
14.99
0.560
0.590
eA
15.55
15.95
0.612
0.628
eB
3.20
3.61
0.126
0.142
L
2.03
2.29
0.080
0.090
9/12
M4Z28-BR00SH, M4Z32-BR00SH
Figure 7. SH – 4-pin SNAPHAT Housing for 120mAh Battery Package Outline
A1
eA
A2
A
A3
B
L
eB
D
E
SHZP-A
Note: Drawing is not to scale.
Table 6. SH – 4-pin SNAPHAT Housing for 120mAh Battery Package Mechanical Data
mm
inches
Symb
Typ
Min
A
Typ
Min
10.54
Max
0.415
A1
8.00
8.51
0.315
0.335
A2
7.24
8.00
0.285
0.315
A3
10/12
Max
0.38
0.015
B
0.46
0.56
0.018
0.022
D
21.21
21.84
0.835
0.860
E
17.27
18.03
0.680
0.710
eA
15.55
15.95
0.612
0.628
eB
3.20
3.61
0.126
0.142
L
2.03
2.29
0.080
0.090
M4Z28-BR00SH, M4Z32-BR00SH
REVISION HISTORY
Table 7. Document Revision History
Date
Rev. #
Revision Details
November 1999
1.0
First Issue
29-May-01
2.0
Reformatted
04-Jun-01
2.1
Basic textual changes from reformatting activity
10-Jul-01
2.2
Remove references to “Crystal;” change references to “SUPERVISOR” from Controller;
clarify temperature characteristics
21-Jan-02
2.3
Change to include Crystal Accuracy (Table 3); add text for SNAPHAT insertion force
tolerance and battery characteristics note
20-Aug-02
2.4
Update Insertion/Extraction Forces (Figure 3)
14-Mar-03
2.5
Add Pb-free note on page 1
11/12
M4Z28-BR00SH, M4Z32-BR00SH
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is registered trademark of STMicroelectronics
All other names are the property of their respective owners.
© 2003 STMicroelectronics - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A.
www.st.com
12/12