FRF501G - FRF507G Isolated 5.0 AMPS. Glass Passivated Fast Recovery Rectifiers ITO-220AB Features Glass passivated chip junction. High efficiency, Low VF High current capability High reliability High surge current capability Low power loss Mechanical Data Cases: ITO-220AB molded plastic Epoxy: UL 94V-0 rate flame retardant Terminals: Pure tin plated, Lead free. Leads solderable per MIL-STD-202, Method 208 guaranteed Polarity: As marked High temperature soldering guaranteed: o 260 C /10 seconds 0.25”,(6.35mm) from case. Mounting position: Any Weight: 2.24 grams Mounting torque: 5 in – 1bs. max. Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current See Fig. 1 Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @2.5A Maximum DC Reverse Current o @T C =25 C at Rated DC Blocking Voltage o @ T C =125 C Symbol FRF FRF FRF FRF FRF FRF FRF Units 501G 502G 503G 504G 505G 506G 507G V RRM 50 100 200 400 600 800 1000 V V RMS 35 70 140 280 420 560 700 V V DC 50 100 200 400 600 800 1000 V I(AV) 5.0 A IFSM 30 A VF 1.5 V IR 5.0 100 uA uA nS pF o C/W o C Maximum Reverse Recovery Time (Note1) Trr Typical Junction Capacitance ( Note 2 ) Cj Typical Thermal Resistance ( Note 3 ) R θJC 150 250 140 4.0 -65 to +150 Operating and Storage Temperature Range T J, T STG 1. Reverse Recovery Test Conditions: I F =0.5A, I R =1.0A, I RR =0.25A Notes: 2. Measured at 1MHz and Applied Reverse Voltage of 4.0 Volts D.C. 3. Mount on Heatsink Size 2” x 3” x 0.25” Al-Plate. 500 Version: A06 RATINGS AND CHARACTERISTIC CURVES (FRF501G THRU FRF507G) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE FIG.2- TYPICAL REVERSE CHARACTERISTICS PER LEG 1000 4 INSTANTANEOUS REVERSE CURRENT. ( A) AVERAGE FORWARD CURRENT. (A) 5 3 2 1 0 0 50 100 150 o LEAD TEMPERATURE. ( C) FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PER LEG 30 100 Tj=125 0C 10 1.0 Tj=25 0C PEAK FORWARD SURGE CURRENT. (A) 0.1 25 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 8.3ms Single Half Sine Wave JEDEC Method 20 15 10 5 0 1 2 5 10 20 50 100 8.0 FIG.5- TYPICAL FORWARD CHARACTERISTICS PER LEG NUMBER OF CYCLES AT 60Hz INSTANTANEOUS FORWARD CURRENT. (A) 4.0 FIG.4- TYPICAL JUNCTION CAPACITANCE PER LEG 300 CAPACITANCE.(pF) 250 200 150 100 Tj=25 0C f=1.0MHz Vsig=50mVp-p 50 2.0 1.0 0.4 0.2 0.1 0.04 0 0.1 0.5 1.0 Tj=25oC Pulse Width=300 s 1% Duty Cycle 0.02 5 10 50 100 500 0.01 0.8 1000 REVERSE VOLTAGE. (V) 0.9 1.0 1.1 1.2 1.3 1.4 1.5 INSTANTANEOUS FORWARD VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 0 -0.25A (+) -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm Version: A06