RS1AL - RS1ML 0.8 AMP. Surface Mount Fast Recovery Rectifiers Sub SMA Features For surface mounted application Glass passivated junction chip Built-in strain relief, ideal for automated placement Plastic material used carries Underwriters Laboratory Classification 94V-0 Fast switching for high efficiency Higho temperature soldering: 260 C/ 10 seconds at terminals Mechanical Data Cases: Molded plastic Terminals: Solder plated Polarity: Indicated by cathode band Packing: 8mm / 12mm tape per EIA STD RS-481 Weight: 15 mg Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% RS RS Symbol RS Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Marking Code (Note 1) Maximum Average Forward Rectified Current See Fig. 1 @TL=90oC Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 1.0A Maximum DC Reverse Current @ TA =25 OC at Rated DC Blocking Voltage @ TA=125 OC Maximum Reverse Recovery Time ( Note 2 ) Typical Junction Capacitance ( Note 3 ) Typical Thermal Resistance (Note 4) Operating Temperature Range Storage Temperature Range Notes: VRRM VRMS VDC 1AL 1BL 1DL RS 1GL RS 1JL RS 1KL RS 1ML Units 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 V V V RALYM RBLYM RDLYM RGLYM RJLYM RKLYM RMLYM I(AV) 0.8 A IFSM 30 A VF 1.3 V IR 5 50 uA uA nS pF 150 TRR Cj R θJA R θJL TJ TSTG 250 10 105 32 -55 to +150 -55 to +150 500 o C /W o o C C 1. RALYM: R=1.0A, A=50V, L-Low Profile, Y-Year Code, M-Month Code. 2. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 3. Measured at 1 MHz and Applied VR=4.0 Volts 4. Mounted on P.C.B. with 0.2” x 0.2” ( 5 mm x 5 mm ) Copper Pad Areas. - 356 - Version: B07 RATINGS AND CHARACTERISTIC CURVES (RS1AL THRU RS1ML) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE FIG.2- TYPICAL REVERSE CHARACTERISTICS 30 RESISTIVE OR INDUCTIVE LOAD 1.0 10 INSTANTANEOUS REVERSE CURRENT. ( A) AVERAGE FORWARD CURRENT. (A) 1.2 0.5 P.C.B. MOUNTED ON 0.2X0.2" (5.0X5.0mm) COPPER PAD AREAS 0 0 20 40 60 80 100 120 140 160 180 o LEAD TEMPERATURE. ( C) FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT Tj=150 0C 1 Tj=100 0C 0.1 Tj=25 0C 0.01 O 0.001 TL=90 C 8.3ms Single Half Sine Wave JEDEC Method 40 20 40 60 80 100 120 140 30 20 FIG.5- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 30 10 0 10 1 10 NUMBER OF CYCLES AT 60Hz 100 FIG.4- TYPICAL JUNCTION CAPACITANCE 40 O JUNCTION CAPACITANCE.(pF) 0 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) INSTANTANEOUS FORWARD CURRENT. (A) PEAK FORWARD SURGE CURRENT. (A) 50 Tj=25 C f=1.0MHz Vsig=50mVp-p 10 Tj=125 0C 1 Tj=25 0C 0.1 Pulse Width=300 s 1% Duty Cycle 1 1 10 REVERSE VOLTAGE. (V) 0.01 0.4 100 0.6 0.8 1.0 1.2 1.4 1.6 1.8 FORWARD VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 0 -0.25A (+) -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm Version: B07