PCM1803A www.ti.com SLES142A – JUNE 2005 – REVISED AUGUST 2006 SINGLE-ENDED, ANALOG-INPUT 24-BIT, 96-kHz STEREO A/D CONVERTER FEATURES APPLICATIONS • • • • • • • • • • • • • • 24-Bit Delta-Sigma Stereo A/D Converter Single-Ended Voltage Input: 3 Vp-p Oversampling Decimation Filter: – Oversampling Frequency: ×64, ×128 – Pass-Band Ripple: ±0.05 dB – Stop-Band Attenuation: –65 dB – On-Chip High-Pass Filter: 0.84 Hz (44.1 kHz) High-Performance: – THD+N: –95 dB (Typically) – SNR: 103 dB (Typically) – Dynamic Range: 103 dB (Typically) PCM Audio Interface: – Master/Slave Mode Selectable – Data Formats: • 24-Bit Left-Justified • 24-Bit I2S • 20-, 24-Bit Right-Justified Sampling Rate: 16 kHz to 96 kHz System Clock: 256 fS, 384 fS, 512 fS, 768 fS Dual Power Supplies: 5 V for Analog, 3.3 V for Digital Package: 20-Pin SSOP AV Amplifier Receiver MD Player CD Recorder Multitrack Receiver Electric Musical Instrument DESCRIPTION The PCM1803A is high-performance, low-cost, single-chip stereo analog-to-digital converter with single-ended analog voltage input. The PCM1803A uses a delta-sigma modulator with 64- and 128-times oversampling, and includes a digital decimation filter and high-pass filter, which removes the dc component of the input signal. For various applications, the PCM1803A supports master and slave modes and four data formats in serial interface. The PCM1803A is suitable for a wide variety of cost-sensitive consumer applications where good performance and operation from a 5-V analog supply and 3.3-V digital supply are required. The PCM1803A is fabricated using a highly advanced CMOS process and is available in a small 20-pin SSOP package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. System Two, Audio Precision are trademarks of Audio Precision, Inc. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2005–2006, Texas Instruments Incorporated PCM1803A www.ti.com SLES142A – JUNE 2005 – REVISED AUGUST 2006 This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PIN ASSIGNMENTS PCM1803A (TOP VIEW) 1 2 3 4 5 6 7 8 9 10 VINL VINR VREF1 VREF2 VCC AGND PDWN BYPAS TEST LRCK 20 19 18 17 16 15 14 13 12 11 MODE1 MODE0 FMT1 FMT0 OSR SCKI VDD DGND DOUT BCK P0009-03 BLOCK DIAGRAM Delta-Sigma Modulator VINL ×1/64 , ×1/128 Decimation Filter With High-Pass Filter VREF1 Reference VREF2 Serial Interface Mode/ Format Control Delta-Sigma Modulator VINR BCK LRCK DOUT FMT0 FMT1 MODE0 MODE1 BYPAS TEST OSR Clock and Timing Control Power Supply VCC AGND DGND PDWN SCKI VDD B0004-06 2 Submit Documentation Feedback PCM1803A www.ti.com SLES142A – JUNE 2005 – REVISED AUGUST 2006 DEVICE INFORMATION TERMINAL FUNCTIONS TERMINAL NAME NO. I/O AGND 6 – BCK 11 I/O DESCRIPTION Analog GND Audio data bit clock input/output (1) BYPAS 8 I HPF bypass control. LOW: Normal mode (dc reject); HIGH: Bypass mode (through) (2) DGND 13 – Digital GND DOUT 12 O Audio data digital output FMT0 17 I Audio data format select input 0. See Data Format section. (2) FMT1 18 I Audio data format select input 1. See Data Format section. (2) LRCK 10 I/O MODE0 19 I Mode select input 0. See Data Format section. (2) MODE1 20 I Mode select input 1. See Data Format section. (2) OSR 16 I Oversampling ratio select input. LOW: ×64 fS, HIGH: ×128 fS Audio data latch enable input/output (1) PDWN 7 I Power-down control, active-low SCKI 15 I System clock input: 256 fS, 384 fS, 512 fS, or 768 fS TEST 9 I Test, must be connected to DGND (2) VCC 5 – Analog power supply, 5-V VDD 14 – Digital power supply, 3.3-V VINL 1 I Analog input, L-channel VINR 2 I Analog input, R-channel VREF1 3 – Reference-voltage-1 decoupling capacitor VREF2 4 – Reference-voltage-2 decoupling capacitor (1) (2) (3) (2) (2) (3) Schmitt-trigger input Schmitt-trigger input with internal pulldown (50 kΩ, typically), 5-V tolerant Schmitt-trigger input, 5-V tolerant ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) (1) Supply voltage VCC –0.3 V to 6.5 V Supply voltage VDD –0.3 V to 4 V Ground voltage differences AGND, DGND Digital input voltage, VI LRCK, BCK, DOUT Digital input voltage, VI PDWN, BYPAS, TEST, SCKI, OSR, FMT0, FMT1, MODE0, MODE1 Analog input voltage, VI VINL, VINR, VREF1, VREF2 Input current, II Any pins except supplies ±0.1 V –0.3 V to (VDD + 0.3 V) < 4 V –0.3 V to 6.5 V –0.3 V to (VCC + 0.3 V) < 6.5 V ±10 mA Ambient temperature under bias, Tbias –40°C to 125°C Storage temperature, Tstg –55°C to 150°C Junction temperature, TJ 150°C Lead temperature (soldering) 260°C, 5 s Package temperature (IR reflow, peak) (1) 260°C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Submit Documentation Feedback 3 PCM1803A www.ti.com SLES142A – JUNE 2005 – REVISED AUGUST 2006 RECOMMENDED OPERATING CONDITIONS over operating free-air temperature range MIN NOM MAX Analog supply voltage, VCC 4.5 5 5.5 V Digital supply voltage, VDD 2.7 3.3 3.6 V Analog input voltage, full-scale (–0 dB) 3 Digital input logic family Digital input clock frequency UNIT Vp-p TTL System clock Sampling clock 8.192 49.152 MHz 32 96 kHz 20 pF 85 °C MAX UNIT Digital output load capacitance Operating free-air temperature, TA –25 ELECTRICAL CHARACTERISTICS All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 44.1 kHz, system clock = 384 fS, oversampling ratio = ×128, 24-bit data (unless otherwise noted) PARAMETER TEST CONDITIONS MIN Resolution TYP 24 Bits DATA FORMAT Left-justified, I2S, right-justified Audio data interface format Audio data bit length 20, 24 Audio data format fS Sampling frequency System clock frequency Bits MSB-first, 2s complement 16 44.1 96 256 fS 4.096 11.2896 24.576 384 fS 6.144 16.9344 36.864 512 fS 8.192 22.5792 49.152 768 fS 12.288 33.8688 kHz MHz – INPUT LOGIC VIH (1) VIL (1) VIH (2) (3) Input logic-level voltage VIL (2) (3) IIH (1) (2) IIL (1) (2) IIH (3) 2 VDD 0 0.8 2 5.5 0 0.8 ±10 VIN = VDD Input logic-level current IIL (3) Vdc ±10 VIN = 0 VIN = VDD 65 100 µA ±10 VIN = 0 OUTPUT LOGIC VOH (4) VOL (4) Output logic-level voltage IOUT = –4 mA 2.8 IOUT = 4 mA 0.5 Vdc DC ACCURACY Gain mismatch, channel-to-channel ±1 ±3 % of FSR Gain error ±2 ±4 % of FSR Bipolar zero error (1) (2) (3) (4) 4 HPF bypass ±0.4 % of FSR Pins 10–11: LRCK, BCK (Schmitt-trigger input, in slave mode) Pin 15: SCKI (Schmitt-trigger input, 5-V tolerant) Pins 7–9, 16–20: PDWN, BYPAS, TEST, OSR, FMT0, FMT1, MODE0, MODE1 (Schmitt-trigger input, with 50-kΩ typical pulldown resistor, 5-V tolerant) Pins 10–12: LRCK, BCK (in master mode), DOUT Submit Documentation Feedback PCM1803A www.ti.com SLES142A – JUNE 2005 – REVISED AUGUST 2006 ELECTRICAL CHARACTERISTICS (continued) All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 44.1 kHz, system clock = 384 fS, oversampling ratio = ×128, 24-bit data (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX VIN = –0.5 dB, fS = 44.1 kHz –95 –89 VIN = –0.5 dB, fS = 96 kHz (6) –93 VIN = –60 dB, fS = 44.1 kHz –41 VIN = –60 dB, fS = 96 kHz (6) –41 UNIT DYNAMIC PERFORMANCE (5) THD+N Total harmonic distortion + noise Dynamic range SNR Signal-to-noise ratio Channel separation fS = 44.1 kHz, A-weighted 100 fS = 96 kHz, A-weighted (6) fS = 44.1 kHz, A-weighted fS = 96 kHz, 103 dB 103 100 A-weighted (6) fS = 44.1 kHz dB 103 dB 103 95 fS = 96 kHz (6) 98 dB 99 ANALOG INPUT VI Input voltage 0.6 VCC Center voltage (VREF1) 0.5 VCC Input impedance Vp-p V 40 kΩ DIGITAL FILTER PERFORMANCE Pass band 0.454 fS Stop band 0.583 fS Hz ±0.05 Pass-band ripple Stop-band attenuation tGD –65 Group delay time HPF frequency response –3 dB Hz dB dB 17.4/fS s 0.019 fS mHz POWER SUPPLY REQUIREMENTS VCC VDD Supply voltage range ICC 4.5 5 5.5 Vdc 2.7 3.3 3.6 Vdc 7.7 10 mA 9 mA Power down (8) Supply current (7) IDD Power dissipation µA 5 fS = 44.1 kHz 6.5 fS = 96 kHz (6) 11.7 Power down (8) 1 fS = 44.1 kHz 60 fS = 96 kHz (6) 77 mW Power down (8) 28 µW mA µA 80 mW TEMPERATURE RANGE TA Operating free-air temperature θJA Thermal resistance (5) (6) (7) (8) –40 20-pin SSOP 85 115 °C °C/W Analog performance specifications are tested using the System Two™ audio measurement system by Audio Precision™, using 400-Hz HPF, 20-kHz LPF in rms mode. fS = 96 kHz, system clock = 256 fS, oversampling ratio = ×64. Minimum load on DOUT (pin 12), BCK (pin 11), LRCK (pin 10) Halt SCKI, BCK, LRCK Submit Documentation Feedback 5 PCM1803A www.ti.com SLES142A – JUNE 2005 – REVISED AUGUST 2006 TYPICAL PERFORMANCE CURVES OF INTERNAL FILTER All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 44.1 kHz, system clock = 384 fS, oversampling ratio = ×128, 24-bit data (unless otherwise noted) Decimation Filter Frequency Response OVERALL CHARACTERISTICS OVERALL CHARACTERISTICS 50 50 Oversampling Ratio = y128 Oversampling Ratio = y64 0 Amplitude − dB Amplitude − dB 0 −50 −100 −150 −50 −100 −150 −200 −200 0 8 16 24 32 40 48 56 64 Normalized Frequency [× fS] 0 8 16 24 32 Normalized Frequency [× fS] G001 Figure 1. G002 Figure 2. STOP-BAND ATTENUATION CHARACTERISTICS PASS-BAND RIPPLE CHARACTERISTICS 0 0.2 −10 0.0 −20 Amplitude − dB Amplitude − dB −30 −40 −50 −60 −70 −80 −90 −0.2 −0.4 −0.6 −0.8 Oversampling Ratio = y128 and y64 −100 0.00 0.25 Oversampling Ratio = y128 and y64 0.50 0.75 Normalized Frequency [× fS] 1.00 −1.0 0.0 G003 Figure 3. 6 0.1 0.2 0.3 Figure 4. Submit Documentation Feedback 0.4 Normalized Frequency [× fS] 0.5 0.6 G004 PCM1803A www.ti.com SLES142A – JUNE 2005 – REVISED AUGUST 2006 TYPICAL PERFORMANCE CURVES OF INTERNAL FILTER (continued) All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 44.1 kHz, system clock = 384 fS, oversampling ratio = ×128, 24-bit data (unless otherwise noted) LOW-CUT FILTER FREQUENCY RESPONSE HPF STOP-BAND CHARACTERISTICS HPF PASS-BAND CHARACTERISTICS 0.2 0 −10 0.0 −20 Amplitude − dB Amplitude − dB −30 −40 −50 −60 −70 −80 −0.2 −0.4 −0.6 −0.8 −90 −100 0.0 −1.0 0.1 0.2 0.3 0.4 Normalized Frequency [× fS/1000] 0 G005 Figure 5. 1 2 3 Normalized Frequency [× fS/1000] 4 G006 Figure 6. Submit Documentation Feedback 7 PCM1803A www.ti.com SLES142A – JUNE 2005 – REVISED AUGUST 2006 TYPICAL PERFORMANCE CURVES All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 44.1 kHz, system clock = 384 fS, oversampling ratio = ×128, 24-bit data (unless otherwise noted) −90 110 −91 109 −92 108 −93 −94 −95 −96 −97 −98 −99 −100 −50 107 106 105 103 SNR 102 −25 0 25 50 75 100 −50 100 0 25 50 75 100 G007 G008 Figure 7. Figure 8. TOTAL HARMONIC DISTORTION + NOISE vs SUPPLY VOLTAGE DYNAMIC RANGE and SIGNAL-TO-NOISE RATIO vs SUPPLY VOLTAGE −91 109 −92 108 Dynamic Range and SNR − dB 110 −93 −94 −95 −96 −97 −98 −99 107 106 105 104 Dynamic Range 103 SNR 102 101 4.50 4.75 5.00 5.25 VCC − Supply Voltage − V 5.50 5.75 100 4.25 G009 Figure 9. 8 −25 TA − Free-Air Temperature − °C −90 −100 4.25 Dynamic Range 104 101 TA − Free-Air Temperature − °C THD+N − Total Harmonic Distortion + Noise − dB DYNAMIC RANGE and SIGNAL-TO-NOISE RATIO vs TEMPERATURE Dynamic Range and SNR − dB THD+N − Total Harmonic Distortion + Noise − dB TOTAL HARMONIC DISTORTION + NOISE vs TEMPERATURE 4.50 4.75 5.00 Figure 10. Submit Documentation Feedback 5.25 VCC − Supply Voltage − V 5.50 5.75 G010 PCM1803A www.ti.com SLES142A – JUNE 2005 – REVISED AUGUST 2006 TYPICAL PERFORMANCE CURVES (continued) All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 44.1 kHz, system clock = 384 fS, oversampling ratio = ×128, 24-bit data (unless otherwise noted) DYNAMIC RANGE and SIGNAL-TO-NOISE RATIO vs fSAMPLE CONDITION −90 110 −91 109 −92 108 Dynamic Range and SNR − dB THD+N − Total Harmonic Distortion + Noise − dB TOTAL HARMONIC DISTORTION + NOISE vs fSAMPLE CONDITION −93 −94 −95 −96 −97 (1)f S = 48 kHz, System Clock = 256 fS, Oversampling Ratio = ×128. (2)f = 96 kHz, System Clock = 256 f , S S Oversampling Ratio = ×64. −98 −99 (1)f S = 48 kHz, System Clock = 256 fS, Oversampling Ratio = ×128. (2)f = 96 kHz, System Clock = 256 f , S S Oversampling Ratio = ×64. 107 106 105 Dynamic Range 104 103 SNR 102 101 100 −100 0 10 20(1) 30(2) 44.1 48 96 fSAMPLE Condition − kHz 10 20(1) 30(2) 44.1 48 96 fSAMPLE Condition − kHz 0 40 G011 Figure 11. 40 G012 Figure 12. OUTPUT SPECTRUM OUTPUT SPECTRUM OUTPUT SPECTRUM 0 0 Input Level = −60 dB Data Points = 8192 −20 −20 −40 −40 Amplitude − dB Amplitude − dB Input Level = −0.5 dB Data Points = 8192 −60 −80 −60 −80 −100 −100 −120 −120 −140 −140 0 5 10 15 20 0 f − Frequency − kHz G013 Figure 13. 5 10 15 20 f − Frequency − kHz G014 Figure 14. Submit Documentation Feedback 9 PCM1803A www.ti.com SLES142A – JUNE 2005 – REVISED AUGUST 2006 TYPICAL PERFORMANCE CURVES (continued) All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 44.1 kHz, system clock = 384 fS, oversampling ratio = ×128, 24-bit data (unless otherwise noted) THD+N − Total Harmonic Distortion + Noise − dB TOTAL HARMONIC DISTORTION + NOISE vs SIGNAL LEVEL 0 −10 −20 −30 −40 −50 −60 −70 −80 −90 −100 −100 −90 −80 −70 −60 −50 −40 −30 −20 −10 0 Signal Level − dB G015 Figure 15. SUPPLY CURRENT SUPPLY CURRENT vs fSAMPLE CONDITION ICC and IDD − Supply Current − mA 15 IDD 10 ICC 5 (1)f S = 48 kHz, System Clock = 256 fS, Oversampling Ratio = ×128. (2)f = 96 kHz, System Clock = 256 f , S S Oversampling Ratio = ×64. 0 0 10 44.1 20(1) 48 30(2) 96 40 fSAMPLE Condition − kHz G016 Figure 16. 10 Submit Documentation Feedback PCM1803A www.ti.com SLES142A – JUNE 2005 – REVISED AUGUST 2006 DEVICE INFORMATION SYSTEM CLOCK The PCM1803A supports 256 fS, 384 fS, 512 fS, and 768 fS as the system clock, where fS is the audio sampling frequency. The system clock must be supplied on SCKI (pin 15). The PCM1803A has a system clock-detection circuit that automatically senses if the system clock is operating at 256 fS, 384 fS, 512 fS, or 768 fS in slave mode. In master mode, the system clock frequency must be selected by MODE0 (pin 19) and MODE1 (pin 20), and 768 fS is not available. The system clock is divided automatically into 128 fS and 64 fS, and these frequencies are used to operate the digital filter and the delta-sigma modulator. Table 1 shows the relationship of typical sampling frequency and system clock frequency, and Figure 17 shows system clock timing. Table 1. Sampling Frequency and System Clock Frequency SYSTEM CLOCK FREQUENCY (MHz) SAMPLING FREQUENCY (kHz) (1) 256 fS 384 fS 512 fS 768 fS (1) 32 8.1920 12.2880 16.3840 24.5760 44.1 11.2896 16.9344 22.5792 33.8688 48 12.2880 18.4320 24.5760 36.8640 64 16.3840 24.5760 32.7680 49.1520 88.2 22.5792 33.8688 45.1584 – 96 24.5760 36.8640 49.1520 – Slave mode only tw(SCKH) tw(SCKL) SCKI 2V SCKI 0.8 V T0005B07 SYMBOL PARAMETER MIN MAX UNIT tw(SCKH) System clock pulse duration, HIGH 8 ns tw(SCKL) System clock pulse duration, LOW 8 ns Figure 17. System Clock Timing POWER-ON-RESET SEQUENCE The PCM1803A has an internal power-on-reset circuit, and initialization (reset) is performed automatically at the time when power-supply voltage (VDD) exceeds 2.2 V (typical). While VDD < 2.2 V (typical) and for 1024 system clock cycles after VDD > 2.2 V (typical), the PCM1803A stays in the reset state, and the digital output is forced to zero. The digital output becomes valid when a time period of 4480/fS has elapsed following release from the reset state. Figure 18 illustrates the internal power-on-reset timing and the digital output for power-on reset. Submit Documentation Feedback 11 PCM1803A www.ti.com SLES142A – JUNE 2005 – REVISED AUGUST 2006 2.6 V 2.2 V 1.8 V VDD Reset Reset Removal Internal Reset 1024 System Clocks 4480 / fS System Clock DOUT Zero Data Normal Data T0014-05 Figure 18. Internal Power-On-Reset Timing SERIAL AUDIO DATA INTERFACE The PCM1803A interfaces the audio system through BCK (pin 11), LRCK (pin 10), and DOUT (pin 12). INTERFACE MODE The PCM1803A supports master mode and slave mode as interface modes, and they are selected by MODE1 (pin 20) and MODE0 (pin 19) as shown in Table 2. In master mode, the PCM1803A provides the timing of serial audio data communications between the PCM1803A and the digital audio processor or external circuit. While in slave mode, the PCM1803A receives the timing for data transfers from an external controller. Table 2. Interface Mode MODE1 MODE0 0 0 Slave mode (256 fS, 384 fS, 512 fS, 768 fS) INTERFACE MODE 0 1 Master mode (512 fS) 1 0 Master mode (384 fS) 1 1 Master mode (256 fS) Master Mode In master mode, BCK and LRCK work as output pins, and these pins are controlled by timing, which is generated in the clock circuit of the PCM1803A. The frequency of BCK is fixed at LRCK × 64. The 768-fS system clock is not available in master mode. Slave Mode In slave mode, BCK and LRCK work as input pins. The PCM1803A accepts the 64-BCK/LRCK or 48-BCK/LRCK format (only for 384 fS and 768 fS system clocks), not the 32-BCK/LRCK format. DATA FORMAT The PCM1803A supports four audio data formats in both master and slave modes, and the data formats are selected by FMT1 (pin 18) and FMT0 (pin 17) as shown in Table 3. Figure 19 illustrates the data formats in slave and master modes. 12 Submit Documentation Feedback PCM1803A www.ti.com SLES142A – JUNE 2005 – REVISED AUGUST 2006 Table 3. Data Formats FORMAT FMT1 FMT0 0 0 0 Left-justified, 24-bit DESCRIPTION 1 0 1 I2S, 24-bit 2 1 0 Right-justified, 24-bit 3 1 1 Right-justified, 20-bit FORMAT 0: FMT[1:0] = 00 24-Bit, MSB-First, Left-Justified Left-Channel LRCK Right-Channel BCK DOUT 1 2 3 22 23 24 MSB 1 LSB 2 3 22 23 24 MSB 1 LSB FORMAT 1: FMT[1:0] = 01 24-Bit, MSB-First, I2S LRCK Left-Channel Right-Channel BCK DOUT 1 2 3 22 23 24 1 LSB MSB 2 3 22 23 24 LSB MSB FORMAT 2: FMT[1:0] = 10 24-Bit, MSB-First, Right-Justified LRCK Left-Channel Right-Channel BCK DOUT 24 1 2 3 22 23 24 MSB LSB 1 2 3 22 23 24 MSB LSB FORMAT 3: FMT[1:0] = 11 20-Bit, MSB-First, Right-Justified LRCK Left-Channel Right-Channel BCK DOUT 20 1 2 MSB 3 18 19 20 LSB 1 2 MSB 3 18 19 20 LSB T0016-11 Figure 19. Audio Data Formats (LRCK and BCK Work as Inputs in Slave Mode and as Outputs in Master Mode) Submit Documentation Feedback 13 PCM1803A www.ti.com SLES142A – JUNE 2005 – REVISED AUGUST 2006 INTERFACE TIMING Figure 20 illustrates the interface timing in slave mode; Figure 21 and Figure 22 illustrate the interface timing in master mode. t(LRCP) 1.4 V LRCK t(BCKL) t(LRSU) t(BCKH) t(LRHD) 1.4 V BCK t(CKDO) t(BCKP) t(LRDO) 0.5 VDD DOUT T0017-02 SYMBOL PARAMETER t(BCKP) BCK period t(BCKH) MIN TYP MAX UNIT 1/(64 fS) ns BCK pulse duration, HIGH 1.5 × t(SCKI) ns t(BCKL) BCK pulse duration, LOW 1.5 × t(SCKI) ns t(LRSU) LRCK setup time to BCK rising edge 40 ns t(LRHD) LRCK hold time to BCK rising edge 20 ns t(LRCP) LRCK period 10 t(CKDO) Delay time, BCK falling edge to DOUT valid –10 40 ns t(LRDO) Delay time, LRCK edge to DOUT valid –10 40 ns tr Rising time of all signals 20 ns tf Falling time of all signals 20 ns µs NOTE: Timing measurement reference level is 1.4 V for input and 0.5 VDD for output. Rising and falling time is measured from 10% to 90% of IN/OUT signal swing. Load capacitance of DOUT is 20 pF. t(SCKI) means SCKI period time. Figure 20. Audio Data Interface Timing (Slave Mode: LRCK and BCK Work as Inputs) 14 Submit Documentation Feedback PCM1803A www.ti.com SLES142A – JUNE 2005 – REVISED AUGUST 2006 t(LRCP) 0.5 VDD LRCK t(BCKL) t(BCKH) t(CKLR) 0.5 VDD BCK t(CKDO) t(BCKP) t(LRDO) 0.5 VDD DOUT T0018-02 SYMBOL PARAMETER t(BCKP) BCK period t(BCKH) BCK pulse duration, HIGH t(BCKL) BCK pulse duration, LOW t(CKLR) Delay time, BCK falling edge to LRCK valid t(LRCP) LRCK period t(CKDO) Delay time, BCK falling edge to DOUT valid t(LRDO) Delay time, LRCK edge to DOUT valid tr tf MIN TYP 150 MAX 1/(64 fS) UNIT 1000 ns 65 600 ns 65 600 ns –10 20 ns 65 µs –10 20 ns –10 20 ns Rising time of all signals 20 ns Falling time of all signals 20 ns 10 1/fS NOTE: Timing measurement reference level is 1.4 V for input and 0.5 VDD for output. Rising and falling time is measured from 10% to 90% of IN/OUT signal swing. Load capacitance of all signals is 20 pF. Figure 21. Audio Data Interface Timing (Master Mode: LRCK and BCK Work as Outputs) 1.4 V SCKI t(SCKBCK) t(SCKBCK) 0.5 VDD BCK T0074-01 SYMBOL t(SCKBCK) PARAMETER Delay time, SCKI rising edge to BCK edge MIN TYP MAX 5 30 UNIT ns NOTE: Timing measurement reference level is 1.4 V for input and 0.5 VDD for output. Load capacitance of BCK is 20 pF. Figure 22. Audio Clock Interface Timing (Master Mode: BCK Works as Output) Submit Documentation Feedback 15 PCM1803A www.ti.com SLES142A – JUNE 2005 – REVISED AUGUST 2006 SYNCHRONIZATION WITH DIGITAL AUDIO SYSTEM In slave mode, the PCM1803A operates under LRCK, synchronized with system clock SCKI. The PCM1803A does not need a specific phase relationship between LRCK and SCKI, but does require the synchronization of LRCK and SCKI. If the relationship between LRCK and SCKI changes more than ±6 BCKs for 64 BCK/frame (±5 BCKs for 48 BCK/frame) during one sample period due to LRCK or SCKI jitter, internal operation of the ADC halts within 1/fS, and digital output is forced to zero data (BPZ code) until resynchronization between LRCK and SCKI occurs. In case of changes less than ±5 BCKs for 64 BCK/frame (±4 BCKs for 48 BCK/frame), resynchronization does not occur and the previously explained digital output control and discontinuity do not occur. Figure 23 illustrates the digital output response for loss of synchronization and resynchronization. During undefined data, the PCM1803A can generate some noise in the audio signal. Also, the transition of normal to undefined data and undefined or zero data to normal creates a discontinuity in the data of the digital output, which can generate some noise in the audio signal. Synchronization Lost State of Synchronization SYNCHRONOUS Resynchronization ASYNCHRONOUS SYNCHRONOUS 1/fS DOUT NORMAL DATA UNDEFINED DATA 32/fS ZERO DATA NORMAL DATA T0020-05 Figure 23. ADC Digital Output for Loss of Synchronization and Resynchronization 16 Submit Documentation Feedback PCM1803A www.ti.com SLES142A – JUNE 2005 – REVISED AUGUST 2006 POWER DOWN PDWN (pin 7) controls operation of the entire ADC. During power-down mode, supply current for the analog portion is shut down and the digital portion is reset; also, DOUT (pin 12) is disabled. It is acceptable to halt the system clock during power-down mode so that power dissipation is minimized. The minimum LOW pulse duration on the PDWN pin is 100 ns. It is recommended to set PWDN (pin 7) to LOW once to obtain stable analog performance when the sampling rate, interface mode, data format, or oversampling control is changed. Table 4. Power-Down Control PWDN Power-Down Mode LOW Power-down mode HIGH Normal operation mode HPF BYPASS The built-in function for dc-component rejection can be bypassed by BYPAS (pin 8) control. In bypass mode, the dc component of the input analog signal, internal dc offset, etc., also are converted and included in the digital output data. Table 5. HPF Bypass Control BYPAS HPF (High-Pass Filter) Mode LOW Normal (no dc component in DOUT) mode HIGH Bypass (dc component in DOUT) mode OVERSAMPLING RATIO CONTROL OSR (pin 16) controls the oversampling ratio of the delta-sigma modulator, ×64 or ×128. The ×128 mode is available for fS ≤ 48 kHz. Table 6. Oversampling Control OSR Oversampling Ratio LOW ×64 HIGH ×128 (fS ≤ 48 kHz) Submit Documentation Feedback 17 PCM1803A www.ti.com SLES142A – JUNE 2005 – REVISED AUGUST 2006 APPLICATION INFORMATION TYPICAL CIRCUIT CONNECTION DIAGRAM Figure 24 illustrates a typical circuit connection diagram where the cutoff frequency of the input HPF is about 160 kHz. C1 + R1 C2 + R2 L-Ch IN R-Ch IN 1 VINL MODE1 20 2 VINR MODE0 19 3 VREF1 FMT1 18 Mode [1:0] C7 C8 C5 C6 + + FMT0 17 OSR 16 Oversampling AGND SCKI 15 System Clock 7 PDWN VDD 14 8 BYPAS DGND 13 9 TEST DOUT 12 Data Out 10 LRCK BCK 11 Data Clock 4 VREF2 5 VCC 6 Power Down LCF Bypass +5 V + C4 Control Format [1:0] PCM1803A Control + C3 +3.3 V Audio Data Processor L/R Clock S0026-03 NOTES: A. C1, C2: A 1-µF electrolytic capacitor gives a 4-Hz (τ = 1 µF × 40 kΩ) cutoff frequency for the input HPF in normal operation and requires a power-on settling time with a 40-ms time constant during the power-on initialization period. B. C3, C4: Bypass capacitors are 0.1-µF ceramic and 10-µF electrolytic, depending on layout and power supply. C. C5, C6: Recommended capacitors are 0.1-µF ceramic and 10-µF electrolytic. D. C7, C8, R1, R2: A 0.01-µF film-type capacitor and 100-Ω resistor give a 160-kHz (τ = 0.01 µF × 100 Ω) cutoff frequency for the anti-aliasing filter in normal operation. Figure 24. Typical Application Diagram 18 Submit Documentation Feedback PCM1803A www.ti.com SLES142A – JUNE 2005 – REVISED AUGUST 2006 APPLICATION INFORMATION (continued) BOARD DESIGN and LAYOUT CONSIDERATIONS VCC, VDD Pins The digital and analog power-supply lines to the PCM1803A should be bypassed to the corresponding ground pins with 0.1-µF ceramic and 10-µF electrolytic capacitors, as close to the pins as possible, to maximize the dynamic performance of the ADC. AGND, DGND Pins To maximize the dynamic performance of the PCM1803A, the analog and digital grounds are not connected internally. These grounds should have low impedance to avoid digital noise feeding back into the analog ground. Therefore, they should be connected directly to each other under the part to reduce potential noise problems. VINL, VINR Pins The VINL and VINR pins need a simple external RC filter (fC = 160 kHz) as an antialiasing filter to remove out-of-band noise from the audio band. If the input signal includes noise with a frequency near the oversampling frequency (64 fS or 128 fS), the noise is folded into the baseband (audio band) signal through A-to-D conversion. The recommended R value is 100 Ω. Film-type capacitors of 0.01-µF should be located as close as possible to the VINL and VINR pins and should be terminated to GND as close as possible to the AGND pin to maximize the dynamic performance of ADC, by suppressing kickback noise from the PCM1803A. VREF1 Pin A 0.1-µF ceramic capacitor and 10-µF electrolytic capacitor are recommended between VREF1 and AGND to ensure low source impedance of the ADC references. These capacitors should be located as close as possible to the VREF1 pin to reduce dynamic errors on the ADC reference. VREF2 Pin The differential voltage between VREF2 and AGND sets the analog input full-scale range. A 0.1-µF ceramic capacitor and 10-µF electrolytic capacitor are recommended between VREF2 and AGND. These capacitors should be located as close as possible to the VREF2 pin to reduce dynamic errors on the ADC reference. DOUT Pin The DOUT pin has enough load drive capability, but if the DOUT line is long, locating a buffer near the PCM1803A and minimizing load capacitance is recommended to minimize the digital-analog crosstalk and maximize the dynamic performance of the ADC. System Clock The quality of the system clock can influence the dynamic performance, because the PCM1803A operates based on a system clock. Therefore, it may be required to consider the system-clock duty, jitter, and the time difference between system-clock transition and BCK or LRCK transition in the slave mode. Submit Documentation Feedback 19 PACKAGE OPTION ADDENDUM www.ti.com 5-Jul-2006 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty PCM1803ADB ACTIVE SSOP DB 20 65 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCM1803ADBG4 ACTIVE SSOP DB 20 65 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCM1803ADBR ACTIVE SSOP DB 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCM1803ADBRG4 ACTIVE SSOP DB 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 MECHANICAL DATA MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0°–ā8° 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Low Power Wireless www.ti.com/lpw Mailing Address: Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2006, Texas Instruments Incorporated