MCC
TM
Micro Commercial Components
FS1A
THRU
omponents
20736 Marilla Street Chatsworth
!"#
$
% !"#
FS1M
Features
•
•
•
•
•
•
•
Lead Free Finish/Rohs Compliant (Note1) ("P"Suffix designates
Compliant. See ordering information)
Epoxy meets UL 94 V-0 flammability rating
Moisture Sensitivity Level 1
Easy Pick And Place
High Temp Soldering: 260°C for 10 Seconds At Terminals
Superfast Recovery Times For High Efficiency
Halogen free available upon request by adding suffix "-HF"
1 Amp Fast Recovery
Silicon Rectifier
50 to 1000 Volts
Maximum
Ratings
Operating Temperature: -50°C to +150°C
•
•
•
•
DO-214AC
(HSMA)
Storage Temperature: -50°C to +150°C
Maximum Thermal Resistance; 15 °C/W Junction To Lead
Maximum Thermal Resistance; 88°C/W Junction To Ambient
MCC
Catalog
Number
Device
Marking
FS1A
FS1B
FS1D
FS1G
FS1J
FS1K
FS1M
FS1A
FS1B
FS1D
FS1G
FS1J
FS1K
FS1M
Maximum
Recurrent
Peak Reverse
Voltage
50V
100V
200V
400V
600V
800V
1000V
Maximum
RMS
Voltage
35V
70V
140V
280V
420V
560V
700V
H
Cathode Band
Maximum
DC
Blocking
Voltage
50V
100V
200V
400V
600V
800V
1000V
J
A
E
D
Note:
B
F
G
DIMENSIONS
Electrical Characteristics @ 25°C Unless Otherwise Specified
Average Forward
IF(AV)
1.0A
Ta = 90°C
current
Peak Forward Surge
IFSM
30A
8.3ms, half sine
Current
IFM = 1.0A;
Maximum
1.30V
Instantaneous
VF
TJ = 25°C*
Forward Voltage
Maximum DC
Reverse Current At
IR
5µA
TJ = 25°C
Rated DC Blocking
200µA TJ = 125°C
Voltage
Maximum Reverse
Recovery Time
150ns
IF=0.5A, IR=1.0A,
FS1A-G
Trr
250ns
Irr=0.25A
FS1J
500ns
FS1K-M
Typical Junction
CJ
50pF
Measured at
Capacitance
1.0MHz, VR=4.0V
*Pulse test: Pulse width 200 µsec, Duty cycle 2%
C
DIM
A
B
C
D
E
F
G
H
J
INCHES
MIN
.078
.067
.002
--.035
.065
.205
.160
.100
MM
MIN
1.98
1.70
.05
--.89
1.65
5.21
4.06
2.57
MAX
.116
.089
.008
.02
.055
.096
.224
.180
.112
MAX
2.95
2.25
.20
.51
1.40
2.45
5.69
4.57
2.84
NOTE
SUGGESTED SOLDER
PAD LAYOUT
0.090”
0.085”
0.070”
1. High Temperature Solder Exemptions Applied, see EU Directive Annex 7.
www.mccsemi.com
Revision: D
1 of 4
2013/01/01
MCC
FS1A thru FS1M
Figure 1
Typical Forward Characteristics
Micro Commercial Components
20
Figure 2
Forward Derating Curve
10
2.4
6
2.2
2.0
4
1.8
2
1.6
25°C
Amps
1.4
1
1.2
.6
Amps
.4
1.0
.8
.6
.2
.4
Single Phase, Half Wave
.2 60Hz Resistive or Inductive Load
.1
.06
0
.04
0
25
50
75
100
125
150
°C
Average Forward Rectified Current - Amperesversus
Ambient Temperature - °C
.02
.01
.8
.6
10
1.2
1.4
1.6
Volts
Instantaneous Forward Current - Amperesversus
Instantaneous Forward Voltage - Volts
Figure 3
Junction Capacitance
100
60
40
20
pF
TJ=25°C
10
6
4
2
1
.1
.2
.4
1
Volts
2
4
10
20
40
100
200
400
1000
Junction Capacitance - pFversus
Reverse Voltage - Volts
www.mccsemi.com
Revision: D
2 of 4
2013/01/01
TM
MCC
FS1A thru FS1M
TM
Figure 4
Peak Forward Surge Current
Micro Commercial Components
36
30
24
Figure 5
New SMA Assembly
18
Amps
12
6
0
Round Lead
Process
1
4
2
6
8 10
20
40
60 80 100
Cycles
Peak Forward Surge Current - Amperesversus
Number Of Cycles At 60Hz - Cycles
Figure 7
Typical Reverse Characteristics
Figure 6
Reverse Recovery Time Characteristic And Test Circuit Diagram
50Ω
100
60
10Ω
40
20
10
Pulse
Generator
Note 2
25Vdc
1Ω
6
4
TA=125°C
2
Oscilloscope
Note 1
µAmps 1
Notes:
1. Rise Time = 7ns max.
Input impedance = 1 megohm, 22pF
2. Rise Time = 10ns max.
Source impedance = 50 ohms
3. Resistors are non-inductive
.6
.4
.2
.1
trr
+0.5A
.06
.04
0
-0.25
TA=25°C
.02
.01
20
40
-1.0
60
80
100
120
140
Volts
1cm
Set Time Base for 20/100ns/cm
Instantaneous Reverse Leakage Current - MicroAmperesversus
Percent Of Rated Peak Reverse Voltage - Volts
www.mccsemi.com
Revision: D
3 of 4
2013/01/01
MCC
TM
Micro Commercial Components
Ordering Information :
Device
Packing
Part Number-TP
Tape&Reel: 3Kpcs/Reel
Note : Adding "-HF" suffix for halogen free, eg. Part Number-TP-HF
***IMPORTANT NOTICE***
Micro Commercial Components Corp. reserves the right to make changes without further notice to any product herein to
make corrections, modifications , enhancements , improvements , or other changes . Micro Commercial Components
Corp . does not assume any liability arising out of the application or use of any product described herein; neither does it
convey any license under its patent rights ,nor the rights of others . The user of products in such applications shall assume all
risks of such use and will agree to hold Micro Commercial Components Corp . and all the companies whose products are
represented on our website, harmless against all damages.
***LIFE SUPPORT***
MCC's products are not authorized for use as critical components in life support devices or systems without the express written
approval of Micro Commercial Components Corporation.
***CUSTOMER AWARENESS***
Counterfeiting of semiconductor parts is a growing problem in the industry. Micro Commercial Components (MCC) is taking
strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. MCC strongly encourages
customers to purchase MCC parts either directly from MCC or from Authorized MCC Distributors who are listed by country on
our web page cited below. Products customers buy either from MCC directly or from Authorized MCC Distributors are genuine
parts, have full traceability, meet MCC's quality standards for handling and storage. MCC will not provide any warranty
coverage or other assistance for parts bought from Unauthorized Sources. MCC is committed to combat this global
problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized
distributors.
www.mccsemi.com
Revision: D
4 of 4
2013/01/01