MCC TM Micro Commercial Components omponents 20736 Marilla Street Chatsworth !"# $ % " !"# PB62F Features • • • • 6 Amp Fast Recovery Bridge Rectifier 200 Volts Low Forward Voltage Any Mounting Position Silver Plated Copper Leads Surge Overload Rating Of 150 Amps PB-6 Maximum Ratings • • Operating Temperature: -55°C to +125°C Storage Temperature: -55°C to +150°C Microsemi Catalog Number Device Marking PB62F PB62F Maximum Recurrent Peak Reverse Voltage 200V B Maximum RMS Voltage 140V Maximum DC Blocking Voltage 200V C E D Electrical Characteristics @ 25°C Unless Otherwise Specified Average Forward Current Peak Forward Surge Current Maximum Forward Voltage Drop Per Element Maximum DC Reverse Current At Rated DC Blocking Voltage Maximum Reverse Recovery Time PB62F IF(AV) 6.0A TJ = 50°C IFSM 150A 8.3ms, half sine + AC A AC VF 1.30V IFM = 3.0A; TJ = 25°C* IR 10µA 1 mA TJ = 25°C TJ = 100°C - A DIMENSIONS Trr 200ns IF=0.5A, IR=1.0A, Irr=0.25A *Pulse test: Pulse width 300 µsec, Duty cycle 1% Revision: 3 G DIM A B C D E G INCHES MIN .578 .230 .750 .405 .038 .145 www.mccsemi.com MAX .618 .270 --.444 .042 --- MM MIN 14.69 5.84 19.10 10.30 0.97 3.70 MAX 15.71 6.86 --11.30 1.07 --- NOTE 2PL 2PL 4PL/TYP ∅ 2003/04/30 MCC PB62F TM Figure 1 Typical Forward Characteristics Micro Commercial Components Figure 2 Typical Reverse Characteristics 100 10 60 6 40 4 20 2 1 10 .6 6 .4 4 .2 2 TJ=25°C 25°C Amps µAmps .1 1 .06 .6 .04 .4 .02 .2 .01 .1 .006 .06 .00 4 .04 .002 .02 .01 .001 20 .2 .4 .6 .8 1.0 1.1 40 60 80 100 120 140 1.2 Volts Volts Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts Instantaneous Reverse Leakage Current I - MicroAmperesversus Percent Of Rated Peak Reverse Voltage - Volts Figure 3 Forward Derating Curve 12 10 8 6 Amps 4 2 Single Phase, Half Wave 60Hz Resistive or Inductive Load 0 0 20 40 60 80 100 120 °C Average Forward Rectified Current - Amperesversus Ambient Temperature - °C Revision: 3 www.mccsemi.com 2003/04/30 MCC PB62F Micro Commercial Components Figure 4 Peak Forward Surge Current 300 250 200 150 Amps 100 50 0 1 2 4 6 8 10 20 40 00 60 80 100 Cycles Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles Figure 5 Reverse Recovery Time Characteristic And Test Circuit Diagram 50Ω 10Ω trr +0.5A 0 Pulse Generator Note 2 25Vdc 1Ω Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive Revision: 3 Oscilloscope Note 1 -0.25 -1.0 1cm Set Time Base for 20/100ns/cm www.mccsemi.com 2003/04/30 TM