ONSEMI NCV7812BD2T

MC7800, MC7800A,
MC7800AE, NCV7800
1.0 A Positive Voltage
Regulators
These voltage regulators are monolithic integrated circuits designed
as fixed−voltage regulators for a wide variety of applications
including local, on−card regulation. These regulators employ internal
current limiting, thermal shutdown, and safe−area compensation. With
adequate heatsinking they can deliver output currents in excess of
1.0 A. Although designed primarily as a fixed voltage regulator, these
devices can be used with external components to obtain adjustable
voltages and currents.
•
•
TO−220
T SUFFIX
CASE 221AB
1
Features
•
•
•
•
•
•
•
http://onsemi.com
Output Current in Excess of 1.0 A
No External Components Required
Internal Thermal Overload Protection
Internal Short Circuit Current Limiting
Output Transistor Safe−Area Compensation
Output Voltage Offered in 1.5%, 2% and 4% Tolerance
Available in Surface Mount D2PAK−3, DPAK−3 and Standard
3−Lead Transistor Packages
NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
Pb−Free Packages are Available
2
Heatsink surface
connected to Pin 2.
3
Pin 1. Input
2. Ground
3. Output
1
3
Heatsink surface (shown as terminal 4 in
case outline drawing) is connected to Pin 2.
4
1 2
Value
Rating
Input Voltage
Symbol
(5.0 − 18 V)
(24 V)
Power Dissipation
369C 221A
Unit
DPAK−3
DT SUFFIX
CASE 369C
3
STANDARD APPLICATION
MC78XX
Input
MAXIMUM RATINGS (TA = 25°C, unless otherwise noted)
D2PAK−3
D2T SUFFIX
CASE 936
Cin*
0.33 mF
Output
CO**
936
VI
35
40
Vdc
PD
Internally Limited
W
Thermal Resistance,
Junction−to−Ambient
RqJA
92
65
Figure
15
°C/W
Thermal Resistance,
Junction−to−Case
RqJC
5.0
5.0
5.0
°C/W
Storage Junction Temperature
Range
Tstg
−65 to +150
°C
Operating Junction Temperature
TJ
+150
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum
Ratings are stress ratings only. Functional operation above the Recommended
Operating Conditions is not implied. Extended exposure to stresses above the
Recommended Operating Conditions may affect device reliability.
*This device series contains ESD protection and exceeds the following tests:
Human Body Model 2000 V per MIL_STD_883, Method 3015.
Machine Model Method 200 V.
A common ground is required between the
input and the output voltages. The input voltage
must remain typically 2.0 V above the output
voltage even during the low point on the input
ripple voltage.
XX, These two digits of the type number
indicate nominal voltage.
* Cin is required if regulator is located an
appreciable distance from power supply
filter.
** CO is not needed for stability; however,
it does improve transient response. Values
of less than 0.1 mF could cause instability.
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 23 of this data sheet.
DEVICE MARKING INFORMATION
See general marking information in the device marking
section on page 31 of this data sheet.
© Semiconductor Components Industries, LLC, 2012
April, 2012 − Rev. 25
1
Publication Order Number:
MC7800/D
MC7800, MC7800A, MC7800AE, NCV7800
Vin
MC7800
R24
50
D2
Zener
LAT 3 A
Q18
LAT
Q17
Q19
QNPN
C3
R19
27.5 k
Q20
QNPN
1.0 P
R14
1.0 k
Q10
QNPN
R18
100 k
R21
600
R22
100
Q7
QNPN
R15
680
R23
0.2
Vout
5.01
Q5
QNPN 2
R17
9.0 k
R11
15 k
Q6
QNPN
D1
Zener
R30
18 k
Q12
QNPN
Q9
QNPN 2
Q15
QNPN
R1
10.66 k
R16
600
R20
17500
Q8
QNPN
R2
1.56 k
Q1
C2
3.0 P
R10
3340-(3316ACT)
R9
3.0 k
R5
4.5 k
Q14
QNPN
Sense
N+
QNPN 6
SUB
Q11 2
C1
30 P
Q4
QNPN
Q13
QNPN
Q3
QNPN
Q2
Q16
QNPN 4
Diode
R6
1.0 k
R7
14 k
R3
1.8 k
R8
5.0 k
This device contains 22 active transistors.
Figure 1. Representative Schematic Diagram
http://onsemi.com
2
R12
3.0 k
R29
9.0 k
R25
6.0 k
R28
9.0 k
R26
3.0 k
R27
9.0 k
R13
11660
MC7800, MC7800A, MC7800AE, NCV7800
ELECTRICAL CHARACTERISTICS (Vin = 10 V, IO = 500 mA, TJ = Tlow to 125°C (Note 1), unless otherwise noted)
MC7805B, NCV7805B
MC7805C
Symbol
Min
Typ
Max
Min
Typ
Max
Unit
Output Voltage (TJ = 25°C)
VO
4.8
5.0
5.2
4.8
5.0
5.2
Vdc
Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)
7.0 Vdc ≤ Vin ≤ 20 Vdc
8.0 Vdc ≤ Vin ≤ 20 Vdc
VO
−
4.75
−
5.0
−
5.25
4.75
−
5.0
−
5.25
−
5.0
1.3
100
50
−
−
0.5
0.8
20
10
−
−
1.3
0.15
100
50
−
−
1.3
1.3
25
25
−
3.2
8.0
−
3.2
6.5
−
−
−
−
−
0.5
−
−
0.3
0.08
1.0
0.8
Characteristic
Line Regulation (Note 4)
7.5 Vdc ≤ Vin ≤ 20 Vdc, 1.0 A
8.0 Vdc ≤ Vin ≤ 12 Vdc
Regline
Load Regulation (Note 4)
5.0 mA ≤ IO ≤ 1.0 A
5.0 mA ≤ IO ≤ 1.5 A (TA = 25°C)
Regload
Quiescent Current
IB
−
−
Vdc
mV
mV
mA
Quiescent Current Change
7.0 Vdc ≤ Vin ≤ 25 Vdc
5.0 mA ≤ IO ≤ 1.0 A (TA = 25°C)
DIB
Ripple Rejection
8.0 Vdc ≤ Vin ≤ 18 Vdc, f = 120 Hz
RR
−
68
−
62
83
−
dB
VI − VO
−
2.0
−
−
2.0
−
Vdc
Output Noise Voltage (TA = 25°C)
10 Hz ≤ f ≤ 100 kHz
Vn
−
10
−
−
10
−
mV/VO
Output Resistance f = 1.0 kHz
rO
−
0.9
−
−
0.9
−
mW
Short Circuit Current Limit (TA = 25°C)
Vin = 35 Vdc
ISC
−
0.2
−
−
0.6
−
A
Peak Output Current (TJ = 25°C)
Imax
−
2.2
−
−
2.2
−
A
TCVO
−
−0.3
−
−
−0.3
−
mV/°C
Dropout Voltage (IO = 1.0 A, TJ = 25°C)
Average Temperature Coefficient of Output Voltage
mA
1. Tlow = 0°C for MC78XXC, MC78XXAC,
= *40°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB
2. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
http://onsemi.com
3
MC7800, MC7800A, MC7800AE, NCV7800
ELECTRICAL CHARACTERISTICS (Vin = 10 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 3), unless otherwise noted)
MC7805AB/MC7805AC/NCV7805AB
Characteristic
Symbol
Min
Typ
Max
Unit
Output Voltage (TJ = 25°C)
VO
4.9
5.0
5.1
Vdc
Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)
7.5 Vdc ≤ Vin ≤ 20 Vdc
VO
4.8
5.0
5.2
Vdc
Line Regulation (Note 4)
Regline
mV
7.5 Vdc ≤ Vin ≤ 25 Vdc, IO = 500 mA
−
0.5
10
8.0 Vdc ≤ Vin ≤ 12 Vdc, IO = 1.0 A
−
0.8
12
8.0 Vdc ≤ Vin ≤ 12 Vdc, IO = 1.0 A, TJ = 25°C
−
1.3
4.0
7.3 Vdc ≤ Vin ≤ 20 Vdc, IO = 1.0 A, TJ = 25°C
−
4.5
10
Load Regulation (Note 4)
Regload
mV
5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C
−
5.0 mA ≤ IO ≤ 1.0 A
250 mA ≤ IO ≤ 750 mA
Quiescent Current
IB
Quiescent Current Change
1.3
25
−
0.8
25
−
0.53
15
−
3.2
6.0
mA
DIB
8.0 Vdc ≤ Vin ≤ 25 Vdc, IO = 500 mA
−
0.3
0.8
7.5 Vdc ≤ Vin ≤ 20 Vdc, TJ = 25°C
−
−
0.8
5.0 mA ≤ IO ≤ 1.0 A
mA
−
0.08
0.5
RR
68
83
−
dB
VI − VO
−
2.0
−
Vdc
Output Noise Voltage (TA = 25°C)
10 Hz ≤ f ≤ 100 kHz
Vn
−
10
−
mV/VO
Output Resistance (f = 1.0 kHz)
rO
−
0.9
−
mW
Short Circuit Current Limit (TA = 25°C)
Vin = 35 Vdc
ISC
−
0.2
−
A
Peak Output Current (TJ = 25°C)
Imax
−
2.2
−
A
TCVO
−
−0.3
−
mV/°C
Ripple Rejection
8.0 Vdc ≤ Vin ≤ 18 Vdc, f = 120 Hz, IO = 500 mA
Dropout Voltage (IO = 1.0 A, TJ = 25°C)
Average Temperature Coefficient of Output Voltage
3. Tlow = 0°C for MC78XXC, MC78XXAC,
= *40°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB
4. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
http://onsemi.com
4
MC7800, MC7800A, MC7800AE, NCV7800
ELECTRICAL CHARACTERISTICS (Vin = 11 V, IO = 500 mA, TJ = Tlow to 125°C (Note 5), unless otherwise noted)
MC7806B/NCV7806B
MC7806C
Symbol
Min
Typ
Max
Min
Typ
Max
Unit
Output Voltage (TJ = 25°C)
VO
5.75
6.0
6.25
5.75
6.0
6.25
Vdc
Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)
VO
Characteristic
Vdc
8.0 Vdc ≤ Vin ≤ 21 Vdc
−
−
−
5.7
6.0
6.3
9.0 Vdc ≤ Vin ≤ 21 Vdc
5.7
6.0
6.3
−
−
−
8.0 Vdc ≤ Vin ≤ 25 Vdc
−
5.5
120
−
0.5
24
9.0 Vdc ≤ Vin ≤ 13 Vdc
−
1.4
60
−
0.8
12
Regload
−
1.3
120
−
1.3
30
mV
IB
−
3.3
8.0
−
3.3
8.0
mA
8.0 Vdc ≤ Vin ≤ 25 Vdc
−
−
−
−
0.3
1.3
5.0 mA ≤ IO ≤ 1.0 A
−
−
0.5
−
0.08
0.5
RR
−
65
−
58
65
−
dB
VI − VO
−
2.0
−
−
2.0
−
Vdc
Vn
−
10
−
−
10
−
mV/VO
Output Resistance f = 1.0 kHz
rO
−
0.9
−
−
0.9
−
mW
Short Circuit Current Limit (TA = 25°C)
ISC
−
0.2
−
−
0.2
−
A
Imax
−
2.2
−
−
2.2
−
A
TCVO
−
−0.3
−
−
−0.3
−
mV/°C
Line Regulation, TJ = 25°C (Note 6)
Load Regulation, TJ = 25°C (Note 6)
Regline
mV
5.0 mA ≤ IO ≤ 1.5 A
Quiescent Current (TJ = 25°C)
Quiescent Current Change
Ripple Rejection
mA
DIB
9.0 Vdc ≤ Vin ≤ 19 Vdc, f = 120 Hz
Dropout Voltage (IO = 1.0 A, TJ = 25°C)
Output Noise Voltage (TA = 25°C)
10 Hz ≤ f ≤ 100 kHz
Vin = 35 Vdc
Peak Output Current (TJ = 25°C)
Average Temperature Coefficient of Output
Voltage
5. Tlow = 0°C for MC78XXC, MC78XXAC,
= *40°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB
6. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
http://onsemi.com
5
MC7800, MC7800A, MC7800AE, NCV7800
ELECTRICAL CHARACTERISTICS (Vin = 11 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 7), unless otherwise noted)
MC7806AC
Characteristic
Symbol
Min
Typ
Max
Unit
Output Voltage (TJ = 25°C)
VO
5.88
6.0
6.12
Vdc
Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)
VO
5.76
6.0
6.24
Vdc
8.6 Vdc ≤ Vin ≤ 21 Vdc
Line Regulation (Note 8)
Regline
mV
8.6 Vdc ≤ Vin ≤ 25 Vdc, IO = 500 mA
−
5.0
12
9.0 Vdc ≤ Vin ≤ 13 Vdc, IO = 1.0 A
−
1.4
15
Load Regulation (Note 8)
Regload
mV
5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C
−
1.3
25
5.0 mA ≤ IO ≤ 1.0 A
−
0.9
25
250 mA ≤ IO ≤ 750 mA
−
0.2
15
−
3.3
6.0
Quiescent Current
IB
Quiescent Current Change
mA
mA
DIB
9.0 Vdc ≤ Vin ≤ 25 Vdc, IO = 500 mA
−
−
0.8
9.0 Vdc ≤ Vin ≤ 21 Vdc, IO = 1.0 A, TJ = 25°C
−
−
0.8
5.0 mA ≤ IO ≤ 1.0 A
−
−
0.5
RR
58
65
−
dB
VI − VO
−
2.0
−
Vdc
Vn
−
10
−
mV/VO
Output Resistance (f = 1.0 kHz)
rO
−
0.9
−
mW
Short Circuit Current Limit (TA = 25°C)
ISC
−
0.2
−
A
Imax
−
2.2
−
A
TCVO
−
−0.3
−
mV/°C
Ripple Rejection
9.0 Vdc ≤ Vin ≤ 19 Vdc, f = 120 Hz, IO = 500 mA
Dropout Voltage (IO = 1.0 A, TJ = 25°C)
Output Noise Voltage (TA = 25°C)
10 Hz ≤ f ≤ 100 kHz
Vin = 35 Vdc
Peak Output Current (TJ = 25°C)
Average Temperature Coefficient of Output Voltage
7. Tlow = 0°C for MC78XXC, MC78XXAC,
= *40°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB
8. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
http://onsemi.com
6
MC7800, MC7800A, MC7800AE, NCV7800
ELECTRICAL CHARACTERISTICS (Vin = 14 V, IO = 500 mA, TJ = Tlow to 125°C (Note 9), unless otherwise noted)
MC7808B/NCV7808B
Characteristic
MC7808C
Symbol
Min
Typ
Max
Min
Typ
Max
Unit
Output Voltage (TJ = 25°C)
VO
7.7
8.0
8.3
7.7
8.0
8.3
Vdc
Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)
VO
Vdc
10.5 Vdc ≤ Vin ≤ 23 Vdc
−
−
−
7.6
8.0
8.4
11.5 Vdc ≤ Vin ≤ 23 Vdc
7.6
8.0
8.4
−
−
−
10.5 Vdc ≤ Vin ≤ 25 Vdc
−
6.0
160
−
6.0
32
11 Vdc ≤ Vin ≤ 17 Vdc
−
1.7
80
−
1.7
16
Regload
−
1.4
160
−
1.4
35
mV
IB
−
3.3
8.0
−
3.3
8.0
mA
10.5 Vdc ≤ Vin ≤ 25 Vdc
−
−
−
−
−
1.0
5.0 mA ≤ IO ≤ 1.0 A
−
−
0.5
−
−
0.5
RR
−
62
−
56
62
−
dB
VI − VO
−
2.0
−
−
2.0
−
Vdc
Vn
−
10
−
−
10
−
mV/VO
Output Resistance f = 1.0 kHz
rO
−
0.9
−
−
0.9
−
mW
Short Circuit Current Limit (TA = 25°C)
ISC
−
0.2
−
−
0.2
−
A
Imax
−
2.2
−
−
2.2
−
A
TCVO
−
−0.4
−
−
−0.4
−
mV/°C
Line Regulation, TJ = 25°C, (Note 10)
Load Regulation, TJ = 25°C (Note 10)
Regline
mV
5.0 mA ≤ IO ≤ 1.5 A
Quiescent Current
Quiescent Current Change
Ripple Rejection
mA
DIB
11.5 Vdc ≤ Vin ≤ 18 Vdc, f = 120 Hz
Dropout Voltage (IO = 1.0 A, TJ = 25°C)
Output Noise Voltage (TA = 25°C)
10 Hz ≤ f ≤ 100 kHz
Vin = 35 Vdc
Peak Output Current (TJ = 25°C)
Average Temperature Coefficient of Output Voltage
9. Tlow = 0°C for MC78XXC, MC78XXAC,
= *40°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB
10. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
http://onsemi.com
7
MC7800, MC7800A, MC7800AE, NCV7800
ELECTRICAL CHARACTERISTICS (Vin = 14 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 11), unless otherwise noted)
MC7808AB/MC7808AC
MC7808AEB
Symbol
Min
Typ
Max
Min
Output Voltage (TJ = 25°C)
VO
7.84
8.0
8.16
Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)
10.6 Vdc ≤ Vin ≤ 23 Vdc
VO
7.7
8.0
−
−
−
Characteristic
Line Regulation (Note 12)
10.6 Vdc ≤ Vin ≤ 25 Vdc, IO = 500 mA
11 Vdc ≤ Vin ≤ 17 Vdc, IO = 1.0 A
10.4 Vdc ≤ Vin ≤ 23 Vdc, TJ = 25°C
Regline
Load Regulation (Note 12)
5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C
5.0 mA ≤ IO ≤ 1.0 A
250 mA ≤ IO ≤ 750 mA
Regload
Quiescent Current
IB
Typ
Max
Unit
7.88
8.12
Vdc
8.3
7.88
8.12
Vdc
6.0
1.7
5.0
15
18
15
−
−
−
6.0
1.7
5.0
15
18
15
−
−
−
1.4
1.0
0.22
25
25
15
−
−
−
1.4
1.0
0.22
25
25
15
−
3.3
6.0
−
3.3
6.0
−
−
−
−
−
−
0.8
0.8
0.5
−
−
−
−
−
−
0.8
0.8
0.5
mV
mV
mA
Quiescent Current Change
11 Vdc ≤ Vin ≤ 25 Vdc, IO = 500 mA
10.6 Vdc ≤ Vin ≤ 23 Vdc, IO = 1.0 A, TJ = 25°C
5.0 mA ≤ IO ≤ 1.0 A
DIB
Ripple Rejection
11.5 Vdc ≤ Vin ≤ 21.5 Vdc, f = 120 Hz, IO = 500 mA
RR
56
62
−
56
62
−
dB
VI − VO
−
2.0
−
−
2.0
−
Vdc
Output Noise Voltage (TA = 25°C)
10 Hz ≤ f ≤ 100 kHz
Vn
−
10
−
−
10
−
mV/VO
Output Resistance f = 1.0 kHz
rO
−
0.9
−
−
0.9
−
mW
Short Circuit Current Limit (TA = 25°C)
Vin = 35 Vdc
ISC
−
0.2
−
−
0.2
−
A
Peak Output Current (TJ = 25°C)
Imax
−
2.2
−
−
2.2
−
A
TCVO
−
−0.4
−
−
−0.4
−
mV/°C
Dropout Voltage (IO = 1.0 A, TJ = 25°C)
Average Temperature Coefficient of Output Voltage
mA
11. Tlow = 0°C for MC78XXC, MC78XXAC,
= *40°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB
12. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
http://onsemi.com
8
MC7800, MC7800A, MC7800AE, NCV7800
ELECTRICAL CHARACTERISTICS (Vin = 15 V, IO = 500 mA, TJ = Tlow to 125°C (Note 13), unless otherwise noted)
MC7809B/NCV7809B
Characteristic
MC7809C
Symbol
Min
Typ
Max
Min
Typ
Max
Unit
Output Voltage (TJ = 25°C)
VO
8.65
9.0
9.35
8.65
9.0
9.35
Vdc
Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)
VO
Vdc
11.5 Vdc ≤ Vin ≤ 24 Vdc
Line Regulation, TJ = 25°C (Note 14)
8.55
9.0
9.45
8.55
9.0
9.45
Regline
mV
11 Vdc ≤ Vin ≤ 26 Vdc
−
6.2
32
−
6.2
32
11.5 Vdc ≤ Vin ≤ 17 Vdc
−
1.8
16
−
1.8
16
Regload
−
1.5
35
−
1.5
35
mV
IB
−
3.4
8.0
−
3.4
8.0
mA
Load Regulation, TJ = 25°C (Note 14)
5.0 mA ≤ IO ≤ 1.5 A
Quiescent Current
Quiescent Current Change
mA
DIB
11.5 Vdc ≤ Vin ≤ 26 Vdc
−
−
1.0
−
−
1.0
5.0 mA ≤ IO ≤ 1.0 A
−
−
0.5
−
−
0.5
RR
56
61
−
56
61
−
dB
VI − VO
−
2.0
−
−
2.0
−
Vdc
Vn
−
10
−
−
10
−
mV/VO
Output Resistance f = 1.0 kHz
rO
−
1.0
−
−
1.0
−
mW
Short Circuit Current Limit (TA = 25°C)
ISC
−
0.2
−
−
0.2
−
A
Imax
−
2.2
−
−
2.2
−
A
TCVO
−
−0.5
−
−
−0.5
−
mV/°C
Ripple Rejection
11.5 Vdc ≤ Vin ≤ 21.5 Vdc, f = 120 Hz
Dropout Voltage (IO = 1.0 A, TJ = 25°C)
Output Noise Voltage (TA = 25°C)
10 Hz ≤ f ≤ 100 kHz
Vin = 35 Vdc
Peak Output Current (TJ = 25°C)
Average Temperature Coefficient of Output Voltage
13. Tlow = 0°C for MC78XXC, MC78XXAC,
= *40°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB
14. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
http://onsemi.com
9
MC7800, MC7800A, MC7800AE, NCV7800
ELECTRICAL CHARACTERISTICS (Vin = 15 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 15), unless otherwise noted)
MC7809AB/MC7809AC
Symbol
Min
Typ
Max
Unit
Output Voltage (TJ = 25°C)
VO
8.82
9.0
9.18
Vdc
Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)
11.5 Vdc ≤ Vin ≤ 24 Vdc
VO
8.65
9.0
9.35
Vdc
−
−
−
6.2
1.8
5.2
16
7.0
16
−
−
−
−
−
−
25
25
15
−
3.3
6.0
−
−
−
−
−
−
0.8
0.8
0.5
56
61
−
Characteristic
Line Regulation (Note 16)
11.5 Vdc ≤ Vin ≤ 26 Vdc, IO = 500 mA
12 Vdc ≤ Vin ≤ 17 Vdc, IO = 1.0 A
11.5 Vdc ≤ Vin ≤ 24 Vdc, TJ = 25°C
Regline
Load Regulation (Note 16)
5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C
5.0 mA ≤ IO ≤ 1.0 A
250 mA ≤ IO ≤ 750 mA
Regload
Quiescent Current
IB
Quiescent Current Change
11.5 Vdc ≤ Vin ≤ 26 Vdc, IO = 500 mA
11.5 Vdc ≤ Vin ≤ 24 Vdc, IO = 1.0 A, TJ = 25°C
5.0 mA ≤ IO ≤ 1.0 A
DIB
Ripple Rejection
11.5 Vdc ≤ Vin ≤ 21.5 Vdc, f = 120 Hz, IO = 500 mA
RR
Dropout Voltage (IO = 1.0 A, TJ = 25°C)
mV
mV
mA
dB
VI _ VO
Output Noise Voltage (TA = 25°C)
10 Hz ≤ f ≤ 100 kHz
Vn
Output Resistance f = 1.0 kHz
mA
2.0
Vdc
mV/VO
−
10
−
rO
−
1.0
−
Short Circuit Current Limit (TA = 25°C)
Vin = 35 Vdc
ISC
−
0.2
Peak Output Current (TJ = 25°C)
Imax
−
2.2
−
A
TCVO
−
−0.5
−
mV/°C
Average Temperature Coefficient of Output Voltage
mW
A
15. Tlow = 0°C for MC78XXC, MC78XXAC,
= *40°C for NCV78XX, MC78XXB, MC78XXAB.
16. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
http://onsemi.com
10
MC7800, MC7800A, MC7800AE, NCV7800
ELECTRICAL CHARACTERISTICS (Vin = 19 V, IO = 500 mA, TJ = Tlow to 125°C (Note 17), unless otherwise noted)
MC7812B/NCV7812B
Characteristic
MC7812C
Symbol
Min
Typ
Max
Min
Typ
Max
Unit
Output Voltage (TJ = 25°C)
VO
11.5
12
12.5
11.5
12
12.5
Vdc
Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)
VO
Vdc
14.5 Vdc ≤ Vin ≤ 27 Vdc
−
−
−
11.4
12
12.6
15.5 Vdc ≤ Vin ≤ 27 Vdc
11.4
12
12.6
−
−
−
14.5 Vdc ≤ Vin ≤ 30 Vdc
−
7.5
240
−
3.8
24
16 Vdc ≤ Vin ≤ 22 Vdc
−
2.2
120
−
0.3
24
14.8 Vdc ≤ Vin ≤ 27 Vdc, IO = 1.0 A
−
−
−
−
−
48
Regload
−
1.6
240
−
8.1
60
mV
IB
−
3.4
8.0
−
3.4
6.5
mA
Line Regulation, TJ = 25°C (Note 18)
Load Regulation, TJ = 25°C (Note 18)
Regline
mV
5.0 mA ≤ IO ≤ 1.5 A
Quiescent Current
Quiescent Current Change
mA
DIB
14.5 Vdc ≤ Vin ≤ 30 Vdc, IO = 1.0 A, TJ = 25°C
−
−
−
−
−
0.7
15 Vdc ≤ Vin ≤ 30 Vdc
−
−
1.0
−
−
0.8
5.0 mA ≤ IO ≤ 1.0 A
−
−
0.5
−
−
0.5
RR
−
60
−
55
60
−
dB
VI − VO
−
2.0
−
−
2.0
−
Vdc
Vn
−
10
−
−
10
−
mV/VO
Output Resistance f = 1.0 kHz
rO
−
1.1
−
−
1.1
−
mW
Short Circuit Current Limit (TA = 25°C)
ISC
−
0.2
−
−
0.2
−
A
Imax
−
2.2
−
−
2.2
−
A
TCVO
−
−0.8
−
−
−0.8
−
mV/°C
Ripple Rejection
15 Vdc ≤ Vin ≤ 25 Vdc, f = 120 Hz
Dropout Voltage (IO = 1.0 A, TJ = 25°C)
Output Noise Voltage (TA = 25°C)
10 Hz ≤ f ≤ 100 kHz
Vin = 35 Vdc
Peak Output Current (TJ = 25°C)
Average Temperature Coefficient of Output Voltage
17. Tlow = 0°C for MC78XXC, MC78XXAC,
= *40°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB
18. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
http://onsemi.com
11
MC7800, MC7800A, MC7800AE, NCV7800
ELECTRICAL CHARACTERISTICS (Vin = 19 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 19), unless otherwise noted)
MC7812AB/MC7812AC/NCV7812AB
Characteristic
Symbol
Min
Typ
Max
Unit
Output Voltage (TJ = 25°C)
VO
11.75
12
12.25
Vdc
Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)
VO
11.5
12
12.5
Vdc
14.8 Vdc ≤ Vin ≤ 27 Vdc
Line Regulation (Note 20)
Regline
mV
14.8 Vdc ≤ Vin ≤ 30 Vdc, IO = 500 mA
−
3.8
18
16 Vdc ≤ Vin ≤ 22 Vdc, IO = 1.0 A
−
2.2
20
14.5 Vdc ≤ Vin ≤ 27 Vdc, TJ = 25°C
−
6.0
120
Load Regulation (Note 20)
Regload
mV
5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C
−
−
25
5.0 mA ≤ IO ≤ 1.0 A
−
−
25
−
3.4
6.0
Quiescent Current
IB
Quiescent Current Change
mA
mA
DIB
15 Vdc ≤ Vin ≤ 30 Vdc, IO = 500 mA
−
−
0.8
14.8 Vdc ≤ Vin ≤ 27 Vdc, TJ = 25°C
−
−
0.8
5.0 mA ≤ IO ≤ 1.0 A, TJ = 25°C
−
−
0.5
RR
55
60
−
dB
VI − VO
−
2.0
−
Vdc
Vn
−
10
−
mV/VO
Output Resistance (f = 1.0 kHz)
rO
−
1.1
−
mW
Short Circuit Current Limit (TA = 25°C)
ISC
−
0.2
−
A
Imax
−
2.2
−
A
TCVO
−
−0.8
−
mV/°C
Ripple Rejection
15 Vdc ≤ Vin ≤ 25 Vdc, f = 120 Hz, IO = 500 mA
Dropout Voltage (IO = 1.0 A, TJ = 25°C)
Output Noise Voltage (TA = 25°C)
10 Hz ≤ f ≤ 100 kHz
Vin = 35 Vdc
Peak Output Current (TJ = 25°C)
Average Temperature Coefficient of Output Voltage
19. Tlow = 0°C for MC78XXC, MC78XXAC,
= *40°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB
20. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
http://onsemi.com
12
MC7800, MC7800A, MC7800AE, NCV7800
ELECTRICAL CHARACTERISTICS (Vin = 23 V, IO = 500 mA, TJ = Tlow to 125°C (Note 21), unless otherwise noted)
MC7815B/NCV7815B
Characteristic
MC7815C
Symbol
Min
Typ
Max
Min
Typ
Max
Unit
Output Voltage (TJ = 25°C)
VO
14.4
15
15.6
14.4
15
15.6
Vdc
Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)
VO
Vdc
17.5 Vdc ≤ Vin ≤ 30 Vdc
−
−
−
14.25
15
15.75
18.5 Vdc ≤ Vin ≤ 30 Vdc
14.25
15
15.75
−
−
−
17.9 Vdc ≤ Vin ≤ 30 Vdc
−
8.5
300
−
8.5
30
20 Vdc ≤ Vin ≤ 26 Vdc
−
3.0
150
−
3.0
28
Regload
−
1.8
300
−
1.8
55
mV
IB
−
3.5
8.0
−
3.5
6.5
mA
17.5 Vdc ≤ Vin ≤ 30 Vdc
−
−
−
−
−
0.8
17.5 Vdc ≤ Vin ≤ 30 Vdc, IO = 1.0 A, TJ = 25°C
−
−
1.0
−
−
0.7
5.0 mA ≤ IO ≤ 1.0 A
−
−
0.5
−
−
0.5
RR
−
58
−
54
58
−
VI − VO
−
2.0
−
−
2.0
−
Vdc
Vn
−
10
−
−
10
−
mV/VO
Output Resistance f = 1.0 kHz
rO
−
1.2
−
−
1.2
−
mW
Short Circuit Current Limit (TA = 25°C)
ISC
−
0.2
−
−
0.2
−
A
Imax
−
2.2
−
−
2.2
−
A
TCVO
−
−1.0
−
−
−1.0
−
mV/°C
Line Regulation, TJ = 25°C (Note 22)
Load Regulation, TJ = 25°C (Note 22)
Regline
mV
5.0 mA ≤ IO ≤ 1.5 A
Quiescent Current
Quiescent Current Change
Ripple Rejection
mA
DIB
dB
18.5 Vdc ≤ Vin ≤ 28.5 Vdc, f = 120 Hz
Dropout Voltage (IO = 1.0 A, TJ = 25°C)
Output Noise Voltage (TA = 25°C)
10 Hz ≤ f ≤ 100 kHz
Vin = 35 Vdc
Peak Output Current (TJ = 25°C)
Average Temperature Coefficient of Output Voltage
21. Tlow = 0°C for MC78XXC, MC78XXAC,
= *40°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB
22. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
http://onsemi.com
13
MC7800, MC7800A, MC7800AE, NCV7800
ELECTRICAL CHARACTERISTICS (Vin = 23 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 23), unless otherwise noted)
MC7815AB/MC7815AC
Characteristic
Symbol
Min
Typ
Max
Unit
Output Voltage (TJ = 25°C)
VO
14.7
15
15.3
Vdc
Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)
VO
14.4
15
15.6
Vdc
17.9 Vdc ≤ Vin ≤ 30 Vdc
Line Regulation (Note 24)
Regline
mV
17.9 Vdc ≤ Vin ≤ 30 Vdc, IO = 500 mA
−
8.5
20
20 Vdc ≤ Vin ≤ 26 Vdc
−
3.0
22
17.5 Vdc ≤ Vin ≤ 30 Vdc, IO = 1.0 A, TJ = 25°C
−
7.0
20
Load Regulation (Note 24)
Regload
mV
5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C
−
1.8
25
5.0 mA ≤ IO ≤ 1.0 A
−
1.5
25
−
1.2
15
−
3.5
6.0
250 mA ≤ IO ≤ 750 mA
Quiescent Current
IB
Quiescent Current Change
mA
mA
DIB
17.5 Vdc ≤ Vin ≤ 30 Vdc, IO = 500 mA
−
−
0.8
17.5 Vdc ≤ Vin ≤ 30 Vdc, IO = 1.0 A, TJ = 25°C
−
−
0.8
5.0 mA ≤ IO ≤ 1.0 A
−
−
0.5
RR
60
80
−
dB
VI − VO
−
2.0
−
Vdc
Vn
−
10
−
mV/VO
Output Resistance f = 1.0 kHz
rO
−
1.2
−
mW
Short Circuit Current Limit (TA = 25°C)
ISC
−
0.2
−
A
Imax
−
2.2
−
A
TCVO
−
−1.0
−
mV/°C
Ripple Rejection
18.5 Vdc ≤ Vin ≤ 28.5 Vdc, f = 120 Hz, IO = 500 mA
Dropout Voltage (IO = 1.0 A, TJ = 25°C)
Output Noise Voltage (TA = 25°C)
10 Hz ≤ f ≤ 100 kHz
Vin = 35 Vdc
Peak Output Current (TJ = 25°C)
Average Temperature Coefficient of Output Voltage
23. Tlow = 0°C for MC78XXC, MC78XXAC,
= *40°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB
24. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
http://onsemi.com
14
MC7800, MC7800A, MC7800AE, NCV7800
ELECTRICAL CHARACTERISTICS (Vin = 27 V, IO = 500 mA, TJ = Tlow to 125°C (Note 25), unless otherwise noted)
MC7818B
Characteristic
MC7818C
Symbol
Min
Typ
Max
Min
Typ
Max
Unit
Output Voltage (TJ = 25°C)
VO
17.3
18
18.7
17.3
18
18.7
Vdc
Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)
VO
Vdc
21 Vdc ≤ Vin ≤ 33 Vdc
−
−
−
17.1
18
18.9
22 Vdc ≤ Vin ≤ 33 Vdc
17.1
18
18.9
−
−
−
21 Vdc ≤ Vin ≤ 33 Vdc
−
9.5
360
−
9.5
50
24 Vdc ≤ Vin ≤ 30 Vdc
−
3.2
180
−
3.2
25
Regload
−
2.0
360
−
2.0
55
mV
IB
−
3.5
8.0
−
3.5
6.5
mA
21 Vdc ≤ Vin ≤ 33 Vdc
−
−
−
−
−
1.0
5.0 mA ≤ IO ≤ 1.0 A
−
−
0.5
−
−
0.5
RR
−
57
−
53
57
−
dB
ViI − VO
−
2.0
−
−
2.0
−
Vdc
Vn
−
10
−
−
10
−
mV/VO
Output Resistance f = 1.0 kHz
rO
−
1.3
−
−
1.3
−
mW
Short Circuit Current Limit (TA = 25°C)
ISC
−
0.2
−
−
0.2
−
A
Imax
−
2.2
−
−
2.2
−
A
TCVO
−
−1.5
−
−
−1.5
−
mV/°C
Line Regulation, (Note 26)
Load Regulation, (Note 26)
Regline
mV
5.0 mA ≤ IO ≤ 1.5 A
Quiescent Current
Quiescent Current Change
Ripple Rejection
mA
DIB
22 Vdc ≤ Vin ≤ 33 Vdc, f = 120 Hz
Dropout Voltage (IO = 1.0 A, TJ = 25°C)
Output Noise Voltage (TA = 25°C)
10 Hz ≤ f ≤ 100 kHz
Vin = 35 Vdc
Peak Output Current (TJ = 25°C)
Average Temperature Coefficient of Output Voltage
25. Tlow = 0°C for MC78XXC, MC78XXAC,
= *40°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB
26. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
http://onsemi.com
15
MC7800, MC7800A, MC7800AE, NCV7800
ELECTRICAL CHARACTERISTICS (Vin = 27 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 27), unless otherwise noted)
MC7818AC
Symbol
Min
Typ
Max
Unit
Output Voltage (TJ = 25°C)
VO
17.64
18
18.36
Vdc
Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)
VO
17.3
18
18.7
Vdc
Characteristic
21 Vdc ≤ Vin ≤ 33 Vdc
Line Regulation (Note 28)
Regline
mV
21 Vdc ≤ Vin ≤ 33 Vdc, IO = 500 mA
−
9.5
22
24 Vdc ≤ Vin ≤ 30 Vdc, IO = 1.0 A
−
3.2
25
24 Vdc ≤ Vin ≤ 30 Vdc, IO = 1.0 A, TJ = 25°C
−
3.2
10.5
20.6 Vdc ≤ Vin ≤ 33 Vdc, IO = 1.0 A, TJ = 25°C
−
8.0
22
Load Regulation (Note 28)
Regload
mV
5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C
−
2.0
25
5.0 mA ≤ IO ≤ 1.0 A
−
1.8
25
250 mA ≤ IO ≤ 750 mA
−
1.5
15
−
3.5
6.0
Quiescent Current
IB
Quiescent Current Change
mA
DIB
21 Vdc ≤ Vin ≤ 33 Vdc, IO = 500 mA
−
−
0.8
21.5 Vdc ≤ Vin ≤ 30 Vdc, TJ = 25°C
−
−
0.8
5.0 mA ≤ IO ≤ 1.0 A
mA
−
−
0.5
RR
53
57
−
dB
VI − VO
−
2.0
−
Vdc
Vn
−
10
−
mV/VO
Output Resistance f = 1.0 kHz
rO
−
1.3
−
mW
Short Circuit Current Limit (TA = 25°C)
ISC
−
0.2
−
A
Imax
−
2.2
−
A
TCVO
−
−1.5
−
mV/°C
Ripple Rejection
22 Vdc ≤ Vin ≤ 32 Vdc, f = 120 Hz, IO = 500 mA
Dropout Voltage (IO = 1.0 A, TJ = 25°C)
Output Noise Voltage (TA = 25°C)
10 Hz ≤ f ≤ 100 kHz
Vin = 35 Vdc
Peak Output Current (TJ = 25°C)
Average Temperature Coefficient of Output Voltage
27. Tlow = 0°C for MC78XXC, MC78XXAC,
= *40°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB
28. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
http://onsemi.com
16
MC7800, MC7800A, MC7800AE, NCV7800
ELECTRICAL CHARACTERISTICS (Vin = 33 V, IO = 500 mA, TJ = Tlow to 125°C (Note 29), unless otherwise noted)
MC7824B
Characteristic
MC7824C
Symbol
Min
Typ
Max
Min
Typ
Max
Unit
Output Voltage (TJ = 25°C)
VO
23
24
25
23
24
25
Vdc
Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)
VO
Vdc
27 Vdc ≤ Vin ≤ 38 Vdc
−
−
−
22.8
24
25.2
28 Vdc ≤ Vin ≤ 38 Vdc
22.8
24
25.2
−
−
−
27 Vdc ≤ Vin ≤ 38 Vdc
−
11.5
480
−
2.7
60
30 Vdc ≤ Vin ≤ 36 Vdc
−
3.8
240
−
2.7
48
Regload
−
2.1
480
−
4.4
65
mV
IB
−
3.6
8.0
−
3.6
6.5
mA
27 Vdc ≤ Vin ≤ 38 Vdc
−
−
−
−
−
1.0
5.0 mA ≤ IO ≤ 1.0 A
−
−
0.5
−
−
0.5
RR
−
54
−
50
54
−
dB
VI − VO
−
2.0
−
−
2.0
−
Vdc
Vn
−
10
−
−
10
−
mV/VO
Output Resistance f = 1.0 kHz
rO
−
1.4
−
−
1.4
−
mW
Short Circuit Current Limit (TA = 25°C)
ISC
−
0.2
−
−
0.2
−
A
Imax
−
2.2
−
−
2.2
−
A
TCVO
−
−2.0
−
−
−2.0
−
mV/°C
Line Regulation, (Note 30)
Load Regulation, (Note 30)
Regline
mV
5.0 mA ≤ IO ≤ 1.5 A
Quiescent Current
Quiescent Current Change
Ripple Rejection
mA
DIB
28 Vdc ≤ Vin ≤ 38 Vdc, f = 120 Hz
Dropout Voltage (IO = 1.0 A, TJ = 25°C)
Output Noise Voltage (TA = 25°C)
10 Hz ≤ f ≤ 100 kHz
Vin = 35 Vdc
Peak Output Current (TJ = 25°C)
Average Temperature Coefficient of Output Voltage
29. Tlow = 0°C for MC78XXC, MC78XXAC,
= *40°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB
30. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
http://onsemi.com
17
MC7800, MC7800A, MC7800AE, NCV7800
ELECTRICAL CHARACTERISTICS (Vin = 33 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 31), unless otherwise noted)
MC7824AC
Characteristic
Symbol
Min
Typ
Max
Unit
Output Voltage (TJ = 25°C)
VO
23.5
24
24.5
Vdc
Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)
VO
23.2
24
25.8
Vdc
27.3 Vdc ≤ Vin ≤ 38 Vdc
Line Regulation (Note 32)
Regline
mV
27 Vdc ≤ Vin ≤ 38 Vdc, IO = 500 mA
−
11.5
25
30 Vdc ≤ Vin ≤ 36 Vdc, IO = 1.0 A
−
3.8
28
30 Vdc ≤ Vin ≤ 36 Vdc, TJ = 25°C
−
3.8
12
26.7 Vdc ≤ Vin ≤ 38 Vdc, IO = 1.0 A, TJ = 25°C
−
10
25
Load Regulation (Note 32)
Regload
mV
5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C
−
2.1
15
5.0 mA ≤ IO ≤ 1.0 A
−
2.0
25
250 mA ≤ IO ≤ 750 mA
−
1.8
15
−
3.6
6.0
Quiescent Current
IB
Quiescent Current Change
mA
DIB
27.3 Vdc ≤ Vin ≤ 38 Vdc, IO = 500 mA
−
−
0.8
27 Vdc ≤ Vin ≤ 38 Vdc, TJ = 25°C
−
−
0.8
5.0 mA ≤ IO ≤ 1.0 A
mA
−
−
0.5
RR
45
54
−
dB
VI − VO
−
2.0
−
Vdc
Vn
−
10
−
mV/VO
Output Resistance (f = 1.0 kHz)
rO
−
1.4
−
mW
Short Circuit Current Limit (TA = 25°C)
ISC
−
0.2
−
A
Imax
−
2.2
−
A
TCVO
−
−2.0
−
mV/°C
Ripple Rejection
28 Vdc ≤ Vin ≤ 38 Vdc, f = 120 Hz, IO = 500 mA
Dropout Voltage (IO = 1.0 A, TJ = 25°C)
Output Noise Voltage (TA = 25°C)
10 Hz ≤ f ≤ 100 kHz
Vin = 35 Vdc
Peak Output Current (TJ = 25°C)
Average Temperature Coefficient of Output Voltage
31. Tlow = 0°C for MC78XXC, MC78XXAC,
= *40°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB
32. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
http://onsemi.com
18
MC7800, MC7800A, MC7800AE, NCV7800
3.0
80
2.5
RR, RIPPLE REJECTION (dB)
I O, OUTPUT CURRENT (A)
TJ = -40°C
TJ = 0°C
2.0
TJ = 25°C
1.5
TJ = 85°C
1.0
TJ = 125°C
0.5
0
4.0
6.0
8.0
10
12
15
20
30
25
60
50
40
4.0
40
35
70
f = 120 Hz
IO = 20 mA
DVin = 1.0 V(RMS)
PART # Vin
MC7805C= 10 V
MC7806C= 11 V
MC7808C= 14 V
MC7812C= 19 V
MC7815C= 23 V
MC7818C= 27 V
MC7824C= 33 V
6.0
8.0
10
Vin−Vout, INPUT/OUTPUT VOLTAGE DIFFERENTIAL (V)
12
14
16
18
20
22
24
VO, OUTPUT VOLTAGE (V)
Figure 2. Peak Output Current as a Function of
Input/Output Differential Voltage (MC78XXC, AC, B)
Figure 3. Ripple Rejection as a Function of
Output Voltages (MC78XXC, AC, B)
VO, OUTPUT VOLTAGE (V)
70
MC78XXB, C, AC
60
Vin = 8.0 V to 18 V
IO = 500 mA
f = 120 Hz
TA = 25°C
50
40
30
0.01
0.1
1.0
Vin = 20 V
IO = 5.0 mA
5.0
4.9
4.8
-60
10
-20
20
60
100
140
f, FREQUENCY (kHz)
TJ, JUNCTION TEMPERATURE (°C)
Figure 4. Ripple Rejection as a Function of
Frequency (MC78XXC, AC, B)
Figure 5. Output Voltage as a Function of
Junction Temperature (MC7805C, AC, B)
8.20
8.15
VO, OUTPUT VOLTAGE (V)
RR, RIPPLE REJECTION (dB)
80
Vin = 14 V
IO = 1.0 mA
8.10
8.05
8.00
7.95
7.90
7.85
7.80
-40 -20
0
20
40
60
80
100 120 140
160 180
TJ, JUNCTION TEMPERATURE (5C)
Figure 6. Output Voltage as a Function of
Junction Temperature (MC7808AE)
http://onsemi.com
19
180
MC7800, MC7800A, MC7800AE, NCV7800
6.0
IB , QUIESCENT CURRENT (mA)
Z O , OUTPUT IMPEDANCE (m)
Ω
10
5.0
3.0
2.0
f = 120 Hz
IO = 500 mA
CL = 0 mF
1.0
0.5
0.3
0.2
0.1
4.0
8.0
12
16
20
4.0
3.0
2.0
1.0
0
-75
24
Vin = 10 V
VO = 5.0 V
IL = 20 mA
VO, OUTPUT VOLTAGE (V)
-50
-25
0
25
50
75
100
TJ, JUNCTION TEMPERATURE (°C)
Figure 7. Output Impedance as a Function of
Output Voltage (MC78XXC, AC, B)
Figure 8. Quiescent Current as a Function of
Temperature (MC78XXC, AC, B)
http://onsemi.com
20
125
MC7800, MC7800A, MC7800AE, NCV7800
APPLICATIONS INFORMATION
Design Considerations
wire lengths, or if the output load capacitance is large. An
input bypass capacitor should be selected to provide good
high−frequency characteristics to insure stable operation
under all load conditions. A 0.33 mF or larger tantalum,
mylar, or other capacitor having low internal impedance at
high frequencies should be chosen. The bypass capacitor
should be mounted with the shortest possible leads directly
across the regulators input terminals. Normally good
construction techniques should be used to minimize ground
loops and lead resistance drops since the regulator has no
external sense lead.
The MC7800 Series of fixed voltage regulators are
designed with Thermal Overload Protection that shuts down
the circuit when subjected to an excessive power overload
condition, Internal Short Circuit Protection that limits the
maximum current the circuit will pass, and Output Transistor
Safe−Area Compensation that reduces the output short circuit
current as the voltage across the pass transistor is increased.
In many low current applications, compensation
capacitors are not required. However, it is recommended
that the regulator input be bypassed with a capacitor if the
regulator is connected to the power supply filter with long
MC7805
Input
0.33 mF
R
IO
Constant
Current to
Grounded
Load
Output
MC7805
Input
7
0.33 mF
2
0.1 mF
6
3
The MC7800 regulators can also be used as a current source when
connected as above. In order to minimize dissipation the MC7805C is
chosen in this application. Resistor R determines the current as follows:
1.0 k
5.0V
I +
)I
O
B
R
4
10 k
MC1741G
VO = 7.0 V to 20 V
VIN = VO ≥ 2.0 V
IB ^ 3.2 mA over line and load changes.
For example, a 1.0 A current source would require R to be a 5.0 W,
10 W resistor and the output voltage compliance would be the input
voltage less 7.0 V.
The addition of an operational amplifier allows adjustment to higher or
intermediate values while retaining regulation characteristics. The
minimum voltage obtainable with this arrangement is 2.0 V greater than the
regulator voltage.
Figure 9. Current Regulator
Figure 10. Adjustable Output Regulator
RSource
MJ2955 or Equiv.
Input
Input
0.33 mF
R
RSC
RSource
MC78XX
0.33 mF
2N6049
or Equiv.
Output
R
≥ 10 mF
1.0 mF
MJ2955
or Equiv.
1.0 mF
≥ 10 mF
XX = 2 digits of type number indicating voltage.
MC78XX
1.0 mF
Output
XX = 2 digits of type number indicating voltage.
The MC7800 series can be current boosted with a PNP transistor. The
MJ2955 provides current to 5.0 A. Resistor R in conjunction with the VBE
of the PNP determines when the pass transistor begins conducting; this
circuit is not short circuit proof. Input/output differential voltage minimum is
increased by VBE of the pass transistor.
The circuit of Figure 11 can be modified to provide supply protection
against short circuits by adding a short circuit sense resistor, RSC, and an
additional PNP transistor. The current sensing PNP must be able to handle
the short circuit current of the three-terminal regulator. Therefore, a
four-ampere plastic power transistor is specified.
Figure 11. Current Boost Regulator
Figure 12. Short Circuit Protection
http://onsemi.com
21
MC7800, MC7800A, MC7800AE, NCV7800
2.5
20
Vin - Vout , INPUT-OUTPUT VOLTAGE
DIFFERENTIAL (V)
qHS = 5°C/W
12
qHS = 15°C/W
4.0
No Heatsink
0
-50
-25
0
25
50
75
100
125
IO = 500 mA
2.0
IO = 200 mA
1.5
IO = 20 mA
IO = 0 mA
1.0
0.5
DVO = 2% of VO
- - - Extended Curve for MC78XXB
0
-75
150
-50
TA, AMBIENT TEMPERATURE (°C)
-25
0
Figure 13. Worst Case Power Dissipation versus
Ambient Temperature (Case 221A)
JUNCTION‐TO‐AIR (°C/W)
R θ JA, THERMAL RESISTANCE
3.5
PD(max) for TA = 50°C
Free Air
Mounted
Vertically
60
3.0
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
2.0 oz. Copper
L
Minimum
Size Pad
50
2.5
2.0
L
1.5
40
RqJA
30
0
5.0
10
15
20
25
30
1.0
L, LENGTH OF COPPER (mm)
Figure 15. D2PAK Thermal Resistance and Maximum
Power Dissipation versus P.C.B. Copper Length
JUNCTION-TO-AIR ( °C/W)
R θ JA, THERMAL RESISTANCE
100
2.4
PD(max) for TA = 50°C
Free Air
Mounted
Vertically
90
2.0
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
80
Minimum
Size Pad
70
60
2.0 oz. Copper
L
1.6
L
1.2
0.8
50
0.4
RqJA
40
0
0
5.0
50
75
100
125
Figure 14. Input Output Differential as a Function
of Junction Temperature (MC78XXC, AC, B)
80
70
25
TJ, JUNCTION TEMPERATURE (°C)
10
15
20
25
30
L, LENGTH OF COPPER (mm)
Figure 16. DPAK Thermal Resistance and Maximum
Power Dissipation versus P.C.B. Copper Length
http://onsemi.com
22
PD, MAXIMUM POWER DISSIPATION (W)
8.0
IO = 1.0 A
PD, MAXIMUM POWER DISSIPATION (W)
qHS = 0°C/W
16
PD , POWER DISSIPATION (W)
qJC = 5°C/W
qJA = 65°C/W
TJ(max) = 150°C
MC7800, MC7800A, MC7800AE, NCV7800
DEFINITIONS
Line Regulation − The change in output voltage for a
change in the input voltage. The measurement is made under
conditions of low dissipation or by using pulse techniques
such that the average chip temperature is not significantly
affected.
Load Regulation − The change in output voltage for a
change in load current at constant chip temperature.
Maximum Power Dissipation − The maximum total
device dissipation for which the regulator will operate
within specifications.
Quiescent Current − That part of the input current that is
not delivered to the load.
Output Noise Voltage − The rms ac voltage at the output,
with constant load and no input ripple, measured over a
specified frequency range.
Long Term Stability − Output voltage stability under
accelerated life test conditions with the maximum rated
voltage listed in the devices’ electrical characteristics and
maximum power dissipation.
ORDERING INFORMATION
Operating
Temperature Range
Package
Shipping†
D2PAK
50 Units /Rail
MC7805ABD2TG
D2PAK
(Pb−free)
50 Units /Rail
MC7805ABD2TR4
D2PAK
800 / Tape & Reel
D2PAK
(Pb−free)
800 / Tape & Reel
MC7805ABT
TO−220
50 Units /Rail
MC7805ABTG
TO−220
(Pb−free)
50 Units /Rail
MC7805ACD2T
D2PAK
50 Units /Rail
MC7805ACD2TG
D2PAK
50 Units /Rail
D2PAK
800 / Tape & Reel
D2PAK
800 / Tape & Reel
TO−220
50 Units /Rail
MC7805ACTG
TO−220
(Pb−free)
50 Units /Rail
MC7805BD2T
D2PAK
50 Units /Rail
MC7805BD2TG
D2PAK
50 Units /Rail
MC7805BD2TR4
D2PAK
800 / Tape & Reel
MC7805BD2TR4G
D2PAK
800 / Tape & Reel
DPAK
75 Units / Rail
DPAK
(Pb−free)
75 Units / Rail
DPAK
2500 / Tape & Reel
DPAK
(Pb−free)
2500 / Tape & Reel
Device
Nominal Voltage
MC7805ABD2T
TJ = −40°C to +125°C
MC7805ABD2TR4G
(Pb−free)
MC7805ACD2TR4
TJ = 0°C to +125°C
MC7805ACD2TR4G
MC7805ACT
MC7805BDT
5.0 V
(Pb−free)
(Pb−free)
TJ = −40°C to +125°C
MC7805BDTG
MC7805BDTRK
MC7805BDTRKG
(Pb−free)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
*NCV devices: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and
change control.
http://onsemi.com
23
MC7800, MC7800A, MC7800AE, NCV7800
ORDERING INFORMATION
Operating
Temperature Range
Package
Shipping†
MC7805BT
TO−220
50 Units /Rail
MC7805BTG
TO−220
(Pb−free)
50 Units /Rail
NCV7805BDTRKG
DPAK
(Pb−free)
2500 / Tape & Reel
D2PAK
50 Units /Rail
D2PAK
(Pb−free)
50 Units /Rail
D2PAK
800 / Tape & Reel
NCV7805BD2TR4G*
D2PAK
(Pb−free)
800 / Tape & Reel
NCV7805BT*
TO−220
50 Units /Rail
NCV7805BTG*
TO−220
(Pb−free)
50 Units /Rail
D2PAK
50 Units /Rail
MC7805CD2TG
D2PAK
(Pb−free)
50 Units /Rail
MC7805CD2TR4
D2PAK
800 / Tape & Reel
D2PAK
(Pb−free)
800 / Tape & Reel
DPAK
75 Units / Rail
DPAK
(Pb−free)
75 Units / Rail
DPAK
2500 / Tape & Reel
MC7805CDTRKG
DPAK
(Pb−free)
2500 / Tape & Reel
MC7805CT
TO−220
50 Units /Rail
MC7805CTG
TO−220
(Pb−free)
50 Units /Rail
D2PAK
(Pb−free)
800 / Tape & Reel
Device
Nominal Voltage
NCV7805BD2T*
NCV7805BD2TG*
TJ = −40°C to +125°C
NCV7805BD2TR4*
MC7805CD2T
5.0 V
MC7805CD2TR4G
MC7805CDT
TJ = 0°C to +125°C
MC7805CDTG
MC7805CDTRK
NCV7805ABD2TR4G*
5.0 V
TJ = −40°C to +125°C
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
*NCV devices: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and
change control.
http://onsemi.com
24
MC7800, MC7800A, MC7800AE, NCV7800
ORDERING INFORMATION
Operating
Temperature Range
Package
Shipping†
TO−220
50 Units /Rail
TO−220
(Pb−free)
50 Units /Rail
MC7806BD2T
D2PAK
50 Units /Rail
MC7806BD2TG
D2PAK
50 Units /Rail
D2PAK
800 / Tape & Reel
D2PAK
800 / Tape & Reel
MC7806BT
TO−220
50 Units /Rail
MC7806BTG
TO−220
(Pb−free)
50 Units /Rail
MC7806CT
TO−220
50 Units /Rail
TO−220
(Pb−free)
50 Units /Rail
Device
MC7806ACT
MC7806ACTG
Nominal Voltage
6.0 V
TJ = 0°C to +125°C
(Pb−free)
MC7806BD2TR4
MC7806BD2TR4G
MC7806CTG
TJ = −40°C to +125°C
TJ = 0°C to +125°C
(Pb−free)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
*NCV devices: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and
change control.
http://onsemi.com
25
MC7800, MC7800A, MC7800AE, NCV7800
ORDERING INFORMATION
Operating
Temperature Range
Package
Shipping†
MC7808ABD2T
D2PAK
50 Units / Rail
MC7808ABD2TG
D2PAK
50 Units / Rail
D2PAK
800 / Tape & Reel
D2PAK
800 / Tape & Reel
TO−220
50 Units / Rail
MC7808ABTG
TO−220
(Pb−free)
50 Units / Rail
MC7808ACT
TO−220
50 Units / Rail
TO−220
(Pb−free)
50 Units / Rail
TO−220
(Pb−free)
50 Units / Rail
D2PAK
50 Units / Rail
MC7808BD2TG
D2PAK
(Pb−free)
50 Units / Rail
MC7808BD2TR4
D2PAK
800 / Tape & Reel
D2PAK
(Pb−free)
800 / Tape & Reel
DPAK
75 Units / Rail
DPAK
(Pb−free)
75 Units / Rail
DPAK
2500 / Tape & Reel
MC7808BDTRKG
DPAK
(Pb−free)
2500 / Tape & Reel
MC7808BT
TO−220
50 Units /Rail
MC7808BTG
TO−220
(Pb−free)
50 Units /Rail
MC7808CD2T
D2PAK
50 Units /Rail
MC7808CD2TG
D2PAK
50 Units /Rail
MC7808CD2TR4
D2PAK
800 / Tape & Reel
MC7808CD2TR4G
D2PAK
800 / Tape & Reel
DPAK
75 Units / Rail
DPAK
(Pb−free)
75 Units / Rail
Device
Nominal Voltage
(Pb−free)
MC7808ABD2TR4
TJ = −40°C to +125°C
MC7808ABD2TR4G
MC7808ABT
8.0 V
TJ = 0°C to +125°C
MC7808ACTG
MC7808AEBTG
MC7808BD2T
MC7808BD2TR4G
MC7808BDT
TJ = −40°C to +125°C
MC7808BDTG
MC7808BDTRK
(Pb−free)
8.0 V
MC7808CDT
MC7808CDTG
(Pb−free)
(Pb−free)
TJ = 0°C to +125°C
MC7808CDTT5G
MC7808CDTRK
2500 / Tape & Reel
DPAK
2500 / Tape & Reel
MC7808CDTRKG
DPAK
(Pb−free)
2500 / Tape & Reel
MC7808CTG
TO−220
(Pb−free)
50 Units /Rail
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
*NCV devices: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and
change control.
http://onsemi.com
26
MC7800, MC7800A, MC7800AE, NCV7800
ORDERING INFORMATION
Device
Nominal Voltage
Operating
Temperature Range
TJ = −40°C to +125°C
NCV7808BDTG*
NCV7808BDTRKG*
Package
Shipping†
DPAK
(Pb−free)
75 Units / Rail
2500 / Tape & Reel
NCV7808BTG*
TO−220
(Pb−free)
50 Units / Rail
NCV7808BD2TR4G*
D2PAK
(Pb−free)
800 / Tape & Reel
TO−220
(Pb−free)
50 Units /Rail
TO−220
50 Units /Rail
TO−220
(Pb−free)
50 Units /Rail
TO−220
50 Units /Rail
TO−220
(Pb−free)
50 Units /Rail
D2PAK
50 Units /Rail
D2PAK
(Pb−free)
50 Units /Rail
D2PAK
800 / Tape & Reel
D2PAK
(Pb−free)
800 / Tape & Reel
MC7809CT
TO−220
50 Units /Rail
MC7809CTG
TO−220
(Pb−free)
50 Units /Rail
D2PAK
(Pb−free)
800 / Tape & Reel
MC7812ABD2T
D2PAK
50 Units /Rail
MC7812ABD2TG
D2PAK
50 Units /Rail
D2PAK
800 / Tape & Reel
D2PAK
800 / Tape & Reel
MC7812ABT
TO−220
50 Units /Rail
MC7812ABTG
TO−220
(Pb−free)
50 Units /Rail
MC7812ACD2T
D2PAK
50 Units /Rail
MC7812ACD2TG
D2PAK
50 Units /Rail
D2PAK
800 / Tape & Reel
D2PAK
(Pb−free)
800 / Tape & Reel
MC7812ACT
TO−220
50 Units /Rail
MC7812ACTG
TO−220
(Pb−free)
50 Units /Rail
MC7809ABTG
TJ = −40°C to +125°C
MC7809ACT
TJ = 0°C to +125°C
MC7809ACTG
MC7809BT
TJ = −40°C to +125°C
MC7809BTG
MC7809CD2T
MC7809CD2TG
9.0 V
MC7809CD2TR4
TJ = 0°C to +125°C
MC7809CD2TR4G
NCV7809BD2TR4G*
TJ = −40°C to +125°C
(Pb−free)
MC7812ABD2TR4
MC7812ABD2TR4G
12 V
TJ = −40°C to +125°C
(Pb−free)
MC7812ACD2TR4
MC7812ACD2TR4G
(Pb−free)
12 V
TJ = 0°C to +125°C
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
*NCV devices: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and
change control.
http://onsemi.com
27
MC7800, MC7800A, MC7800AE, NCV7800
ORDERING INFORMATION
Operating
Temperature Range
Package
Shipping†
MC7812BD2T
D2PAK
50 Units /Rail
MC7812BD2TG
D2PAK
50 Units /Rail
D2PAK
800 / Tape & Reel
D2PAK
800 / Tape & Reel
DPAK
75 Units / Rail
DPAK
(Pb−free)
75 Units / Rail
DPAK
2500 / Tape & Reel
DPAK
(Pb−free)
2500 / Tape & Reel
TO−220
50 Units / Rail
TO−220
(Pb−free)
50 Units / Rail
NCV7812BD2T*
D2PAK
50 Units /Rail
NCV7812BD2TR4*
D2PAK
800 / Tape & Reel
NCV7812BD2TR4G*
D2PAK
800 / Tape & Reel
NCV7812BT*
TO−220
50 Units /Rail
NCV7812BTG*
TO−220
(Pb−free)
50 Units /Rail
MC7812CD2T
D2PAK
50 Units /Rail
MC7812CD2TG
D2PAK
(Pb−free)
50 Units /Rail
MC7812CD2TR4
D2PAK
800 / Tape & Reel
D2PAK
(Pb−free)
800 / Tape & Reel
Device
Nominal Voltage
(Pb−free)
MC7812BD2TR4
MC7812BD2TR4G
12 V
TJ = −40°C to +125°C
MC7812BDT
MC7812BDTG
MC7812BDTRK
MC7812BDTRKG
MC7812BT
12 V
TJ = −40°C to +125°C
MC7812BTG
12 V
TJ = −40°C to +125°C
MC7812CD2TR4G
MC7812CDT
MC7812CDTG
12 V
TJ = 0°C to +125°C
MC7812CDTRK
(Pb−free)
(Pb−free)
DPAK
75 Units / Rail
DPAK
(Pb−free)
75 Units / Rail
DPAK
2500 / Tape & Reel
MC7812CDTRKG
DPAK
(Pb−free)
2500 / Tape & Reel
MC7812CT
TO−220
50 Units /Rail
MC7812CTG
TO−220
(Pb−free)
50 Units / Rail
TO−220
(Pb−free)
50 Units / Rail
NCV7812ABTG*
12 V
TJ = −40°C to +125°C
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
*NCV devices: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and
change control.
http://onsemi.com
28
MC7800, MC7800A, MC7800AE, NCV7800
ORDERING INFORMATION
Operating
Temperature Range
Package
Shipping†
MC7815ABD2T
D2PAK
50 Units /Rail
MC7815ABD2TG
D2PAK
50 Units /Rail
D2PAK
800 / Tape & Reel
D2PAK
800 / Tape & Reel
MC7815ABT
TO−220
50 Units /Rail
MC7815ABTG
TO−220
(Pb−free)
50 Units /Rail
D2PAK
50 Units /Rail
D2PAK
50 Units /Rail
TO−220
50 Units /Rail
MC7815ACTG
TO−220
(Pb−free)
50 Units / Rail
MC7815BD2T
D2PAK
50 Units /Rail
D2PAK
(Pb−free)
50 Units /Rail
TO−220
(Pb−free)
50 Units / Rail
MC7815BD2TR4
D2PAK
800 / Tape & Reel
MC7815BD2TR4G
D2PAK
800 / Tape & Reel
DPAK
75 Units / Rail
DPAK
(Pb−free)
75 Units / Rail
DPAK
2500 / Tape & Reel
MC7815BDTRKG
DPAK
(Pb−free)
2500 / Tape & Reel
MC7815BT
TO−220
50 Units / Rail
MC7815BTG
TO−220
(Pb−free)
50 Units / Rail
Device
Nominal Voltage
(Pb−free)
MC7815ABD2TR4
TJ = −40°C to +125°C
MC7815ABD2TR4G
MC7815ACD2T
15 V
MC7815ACD2TG
TJ = 0°C to +125°C
MC7815ACT
TJ = −40°C to +125°C
MC7815BD2TG
NCV7815BTG*
(Pb−free)
(Pb−free)
MC7815BDT
MC7815BDTG
(Pb−free)
15 V
TJ = −40°C to +125°C
MC7815BDTRK
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
*NCV devices: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and
change control.
http://onsemi.com
29
MC7800, MC7800A, MC7800AE, NCV7800
ORDERING INFORMATION
Operating
Temperature Range
Package
Shipping†
MC7815CD2T
D2PAK
50 Units /Rail
MC7815CD2TG
D2PAK
50 Units /Rail
MC7815CD2TR4
D2PAK
800 / Tape & Reel
MC7815CD2TR4G
D2PAK
800 / Tape & Reel
DPAK
75 Units / Rail
DPAK
(Pb−free)
75 Units / Rail
DPAK
2500 / Tape & Reel
MC7815CDTRKG
DPAK
(Pb−free)
2500 / Tape & Reel
MC7815CT
TO−220
50 Units /Rail
MC7815CTG
TO−220
(Pb−free)
50 Units /Rail
MC7818ACT
TO−220
50 Units /Rail
TO−220
(Pb−free)
50 Units /Rail
TO−220
50 Units /Rail
TO−220
(Pb−free)
50 Units /Rail
Device
Nominal Voltage
(Pb−free)
(Pb−free)
MC7815CDT
MC7815CDTG
15 V
TJ = 0°C to +125°C
MC7815CDTRK
TJ = 0°C to +125°C
MC7818ACTG
MC7818BT
TJ = −40°C to +125°C
MC7818BTG
D2PAK
50 Units /Rail
D2PAK
800 / Tape & Reel
D2PAK
(Pb−free)
800 / Tape & Reel
MC7818CT
TO−220
50 Units /Rail
MC7818CTG
TO−220
(Pb−free)
50 Units /Rail
MC7818CD2T
18 V
MC7818CD2TR4
MC7818CD2TR4G
TJ = 0°C to +125°C
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
*NCV devices: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and
change control.
http://onsemi.com
30
MC7800, MC7800A, MC7800AE, NCV7800
ORDERING INFORMATION
Operating
Temperature Range
Package
Shipping†
TO−220
50 Units /Rail
TO−220
(Pb−free)
50 Units /Rail
MC7824BD2T
D2PAK
50 Units /Rail
MC7824BD2TG
D2PAK
50 Units /Rail
D2PAK
800 / Tape & Reel
D2PAK
800 / Tape & Reel
TO−220
50 Units /Rail
TO−220
(Pb−free)
50 Units /Rail
D2PAK
50 Units /Rail
MC7824CD2TG
D2PAK
(Pb−free)
50 Units /Rail
MC7824CD2TR4
D2PAK
800 / Tape & Reel
D2PAK
(Pb−free)
800 / Tape & Reel
MC7824CT
TO−220
50 Units /Rail
MC7824CTG
TO−220
(Pb−free)
50 Units /Rail
Device
Nominal Voltage
MC7824ACT
TJ = 0°C to +125°C
MC7824ACTG
(Pb−free)
MC7824BD2TR4
TJ = −40°C to +125°C
MC7824BD2TR4G
(Pb−free)
MC7824BT
24 V
MC7824BTG
MC7824CD2T
TJ = 0°C to +125°C
MC7824CD2TR4G
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
*NCV devices: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and
change control.
MARKING DIAGRAMS
MC
78xxAEyT
AWLYWWG
MC
78xxAyT
AWLYWWG
MC *
78xxyT
AWLYWWG
MC
78xxAyD2T
AWLYWWG
MC
78xxyD2T
AWLYWWG
*
D2PAK−3
D2T SUFFIX
CASE 936
TO−220−3
T SUFFIX
CASE 221A
*This marking diagram also applies to NCV78xx family.
xx
y
A
WL, L
Y
WW
G
= 05, 06, 08, 09, 12, 15, 18, or 24
= B or C
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Device
http://onsemi.com
31
78xxyG
ALYWW
DPAK−3
DT SUFFIX
CASE 369C
MC7800, MC7800A, MC7800AE, NCV7800
PACKAGE DIMENSIONS
TO−220, SINGLE GAUGE
CASE 221AB
ISSUE A
−T−
B
F
T
SEATING
PLANE
C
S
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCHES.
3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND
LEAD IRREGULARITIES ARE ALLOWED.
4. PRODUCT SHIPPED PRIOR TO 2008 HAD DIMENSIONS
S = 0.045 - 0.055 INCHES (1.143 - 1.397 MM)
4
DIM
A
B
C
D
F
G
H
J
K
L
N
Q
R
S
T
U
V
Z
A
Q
U
1 2 3
H
K
Z
L
R
V
J
G
D
N
http://onsemi.com
32
INCHES
MIN
MAX
0.570
0.620
0.380
0.405
0.160
0.190
0.025
0.035
0.142
0.147
0.095
0.105
0.110
0.155
0.018
0.025
0.500
0.562
0.045
0.060
0.190
0.210
0.100
0.120
0.080
0.110
0.020
0.024
0.235
0.255
0.000
0.050
0.045
----0.080
MILLIMETERS
MIN
MAX
14.48
15.75
9.66
10.28
4.07
4.82
0.64
0.88
3.61
3.73
2.42
2.66
2.80
3.93
0.46
0.64
12.70
14.27
1.15
1.52
4.83
5.33
2.54
3.04
2.04
2.79
0.508
0.61
5.97
6.47
0.00
1.27
1.15
----2.04
MC7800, MC7800A, MC7800AE, NCV7800
PACKAGE DIMENSIONS
D2PAK−3
D2T SUFFIX
CASE 936−03
ISSUE C
T
C
A
K
OPTIONAL
CHAMFER
J
2
DETAIL C
DETAIL C
3
F
G
SIDE VIEW
2X
TOP VIEW
D
0.010 (0.254)
N
M
P
R
ES
OPTIONAL
CHAMFER
V
H
1
C
U
ED
S
B
T
TERMINAL 4
L
DUAL GAUGE
CONSTRUCTION
BOTTOM VIEW
SIDE VIEW
SINGLE GAUGE
CONSTRUCTION
T
M
T
SEATING
PLANE
BOTTOM VIEW
DETAIL C
OPTIONAL CONSTRUCTIONS
SOLDERING FOOTPRINT*
10.49
8.38
16.155
2X
3.504
2X
1 016
http://onsemi.com
33
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCHES.
3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS
A AND K.
4. DIMENSIONS U AND V ESTABLISH A MINIMUM
MOUNTING SURFACE FOR TERMINAL 4.
5. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH OR GATE PROTRUSIONS. MOLD FLASH
AND GATE PROTRUSIONS NOT TO EXCEED
0.025 (0.635) MAXIMUM.
6. SINGLE GAUGE DESIGN WILL BE SHIPPED
AFTER FPCN EXPIRATION IN OCTOBER 2011.
DIM
A
B
C
D
ED
ES
F
G
H
J
K
L
M
N
P
R
S
U
V
INCHES
MIN
MAX
0.386
0.403
0.356
0.368
0.170
0.180
0.026
0.036
0.045
0.055
0.018
0.026
0.051 REF
0.100 BSC
0.539
0.579
0.125 MAX
0.050 REF
0.000
0.010
0.088
0.102
0.018
0.026
0.058
0.078
5 _ REF
0.116 REF
0.200 MIN
0.250 MIN
MILLIMETERS
MIN
MAX
9.804 10.236
9.042
9.347
4.318
4.572
0.660
0.914
1.143
1.397
0.457
0.660
1.295 REF
2.540 BSC
13.691 14.707
3.175 MAX
1.270 REF
0.000
0.254
2.235
2.591
0.457
0.660
1.473
1.981
5 _ REF
2.946 REF
5.080 MIN
6.350 MIN
MC7800, MC7800A, MC7800AE, NCV7800
PACKAGE DIMENSIONS
DPAK−3
DT SUFFIX
CASE 369C
ISSUE D
A
E
b3
c2
B
Z
D
1
L4
A
4
L3
b2
e
2
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: INCHES.
3. THERMAL PAD CONTOUR OPTIONAL WITHIN DIMENSIONS b3, L3 and Z.
4. DIMENSIONS D AND E DO NOT INCLUDE MOLD
FLASH, PROTRUSIONS, OR BURRS. MOLD
FLASH, PROTRUSIONS, OR GATE BURRS SHALL
NOT EXCEED 0.006 INCHES PER SIDE.
5. DIMENSIONS D AND E ARE DETERMINED AT THE
OUTERMOST EXTREMES OF THE PLASTIC BODY.
6. DATUMS A AND B ARE DETERMINED AT DATUM
PLANE H.
C
H
DETAIL A
3
DIM
A
A1
b
b2
b3
c
c2
D
E
e
H
L
L1
L2
L3
L4
Z
c
b
0.005 (0.13)
M
H
C
L2
GAUGE
PLANE
C
L
SEATING
PLANE
A1
L1
DETAIL A
ROTATED 905 CW
INCHES
MIN
MAX
0.086 0.094
0.000 0.005
0.025 0.035
0.030 0.045
0.180 0.215
0.018 0.024
0.018 0.024
0.235 0.245
0.250 0.265
0.090 BSC
0.370 0.410
0.055 0.070
0.108 REF
0.020 BSC
0.035 0.050
−−− 0.040
0.155
−−−
MILLIMETERS
MIN
MAX
2.18
2.38
0.00
0.13
0.63
0.89
0.76
1.14
4.57
5.46
0.46
0.61
0.46
0.61
5.97
6.22
6.35
6.73
2.29 BSC
9.40 10.41
1.40
1.78
2.74 REF
0.51 BSC
0.89
1.27
−−−
1.01
3.93
−−−
SOLDERING FOOTPRINT*
6.20
0.244
2.58
0.102
5.80
0.228
3.00
0.118
1.60
0.063
6.17
0.243
SCALE 3:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
34
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC7800/D