MC74VHC1GT125 Noninverting Buffer / CMOS Logic Level Shifter with LSTTL−Compatible Inputs http://onsemi.com MARKING DIAGRAMS 5 SC−88A / SOT−353 / SC−70 DF SUFFIX CASE 419A 5 W1 M G G 1 TSOP−5 / SOT−23 / SC−59 DT SUFFIX CASE 483 W1 M G High Speed: tPD = 3.5 ns (Typ) at VCC = 5 V Low Power Dissipation: ICC = 1 mA (Max) at TA = 25°C W1 M G G 1 5 Features • • • • • • • • • • 5 1 M The MC74VHC1GT125 is a single gate noninverting buffer fabricated with silicon gate CMOS technology. It achieves high speed operation similar to equivalent Bipolar Schottky TTL while maintaining CMOS low power dissipation. The MC74VHC1GT125 requires the 3−state control input (OE) to be set High to place the output into the high impedance state. The device input is compatible with TTL−type input thresholds and the output has a full 5 V CMOS level output swing. The input protection circuitry on this device allows overvoltage tolerance on the input, allowing the device to be used as a logic−level translator from 3 V CMOS logic to 5 V CMOS Logic or from 1.8 V CMOS logic to 3 V CMOS Logic while operating at the high−voltage power supply. The MC74VHC1GT125 input structure provides protection when voltages up to 7 V are applied, regardless of the supply voltage. This allows the MC74VHC1GT125 to be used to interface 5 V circuits to 3 V circuits. The output structures also provide protection when VCC = 0 V. These input and output structures help prevent device destruction caused by supply voltage − input/output voltage mismatch, battery backup, hot insertion, etc. 1 = Device Code = Date Code* = Pb−Free Package (Note: Microdot may be in either location) TTL−Compatible Inputs: VIL = 0.8 V; VIH = 2 V CMOS−Compatible Outputs: VOH > 0.8 VCC; VOL < 0.1 VCC @Load *Date Code orientation and/or position may vary depending upon manufacturing location. Power Down Protection Provided on Inputs and Outputs Balanced Propagation Delays Pin and Function Compatible with Other Standard Logic Families Chip Complexity: FETs = 62; Equivalent Gates = 16 These Devices are Pb−Free and are RoHS Compliant NLV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable OE 1 4 OUT Y OE OUT Y IN A 3 GND 4 OUT Y 5 VCC A Input OE Input Y Output L H X L L H L H Z ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. Figure 2. Logic Symbol September, 2012 − Rev. 14 OE IN A FUNCTION TABLE Figure 1. Pinout (Top View) © Semiconductor Components Industries, LLC, 2012 1 2 5 VCC IN A 2 GND 3 PIN ASSIGNMENT 1 Publication Order Number: MC74VHC1GT125/D MC74VHC1GT125 MAXIMUM RATINGS Symbol Characteristics Value Unit VCC DC Supply Voltage −0.5 to +7.0 V VIN DC Input Voltage −0.5 to +7.0 V −0.5 to 7.0 −0.5 to VCC + 0.5 V −20 mA +20 mA VOUT DC Output Voltage IIK Input Diode Current IOK Output Diode Current IOUT DC Output Current, per Pin +25 mA ICC DC Supply Current, VCC and GND +50 mA PD Power Dissipation in Still Air qJA Thermal Resistance TL VCC = 0 High or Low State VOUT < GND; VOUT > VCC SC−88A, TSOP−5 200 mW SC−88A, TSOP−5 333 °C/W Lead Temperature, 1 mm from Case for 10 s 260 °C TJ Junction Temperature Under Bias +150 °C Tstg Storage Temperature −65 to +150 °C > 2000 > 200 N/A V ±500 mA VESD ESD Withstand Voltage ILatchup Human Body Model (Note 1) Machine Model (Note 2) Charged Device Model (Note 3) Latchup Performance Above VCC and Below GND at 125°C (Note 4) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Tested to EIA/JESD22−A114−A 2. Tested to EIA/JESD22−A115−A 3. Tested to JESD22−C101−A 4. Tested to EIA/JESD78 RECOMMENDED OPERATING CONDITIONS Symbol Min Max Unit VCC DC Supply Voltage Characteristics 3.0 5.5 V VIN DC Input Voltage 0.0 5.5 V DC Output Voltage 0.0 VCC V Operating Temperature Range −55 +125 °C 0 20 ns/V VOUT TA tr , tf Input Rise and Fall Time VCC = 5.0 V ± 0.5 V 90 419,300 47.9 100 178,700 20.4 110 79,600 9.4 120 37,000 4.2 130 17,800 2.0 140 8,900 1.0 TJ = 80 ° C 117.8 TJ = 90 ° C 1,032,200 TJ = 100 ° C 80 FAILURE RATE OF PLASTIC = CERAMIC UNTIL INTERMETALLICS OCCUR TJ = 110° C Time, Years TJ = 120° C Time, Hours TJ = 130 ° C Junction Temperature 5C NORMALIZED FAILURE RATE Device Junction Temperature versus Time to 0.1% Bond Failures 1 1 10 100 TIME, YEARS Figure 3. Failure Rate vs. Time Junction Temperature http://onsemi.com 2 1000 MC74VHC1GT125 ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎ ÎÎÎ ÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎ ÎÎÎ ÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎ ÎÎÎ ÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ DC ELECTRICAL CHARACTERISTICS Symbol Parameter Test Conditions Min 1.4 2.0 2.0 VIH Minimum High−Level Input Voltage 3.0 4.5 5.5 VIL Maximum Low−Level Input Voltage 3.0 4.5 5.5 VOH Minimum High−Level Output Voltage VIN = VIH or VIL VOL Maximum Low−Level Output Voltage VIN = VIH or VIL TA = 25°C VCC (V) Typ TA ≤ 85°C Max Min Max 1.4 2.0 2.0 0.53 0.8 0.8 VIN = VIH or VIL IOH = − 50 mA 3.0 4.5 2.9 4.4 3.0 4.5 VIN = VIH or VIL IOH = − 4 mA IOH = − 8 mA 3.0 4.5 2.58 3.94 VIN = VIH or VIL IOL = 50 mA 3.0 4.5 VIN = VIH or VIL IOL = 4 mA IOL = 8 mA 0.0 0.0 −55 ≤ TA ≤ 125°C Min Max 1.4 2.0 2.0 V 0.53 0.8 0.8 0.53 0.8 0.8 2.9 4.4 2.9 4.4 2.48 3.80 2.34 3.66 Unit V V 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 0.36 0.36 0.44 0.44 0.52 0.52 V IIN Maximum Input Leakage Current VIN = 5.5 V or GND 0 to 5.5 ± 0.10 ± 1.0 ± 1.0 mA ICC Maximum Quiescent Supply Current VIN = VCC or GND 5.5 1.0 20 40 mA ICCT Quiescent Supply Current Input: VIN = 3.4 V Other Input: VCC or GND 5.5 1.35 1.50 1.65 mA IOPD Output Leakage Current VOUT = 5.5 V 0.0 0.5 5.0 10 mA Maximum 3−State Leakage Current VIN = VIH or VIL VOUT = VCC or GND 5.5 ± 0.25 ± 2.5 ± 2.5 mA Output Leakage Current VOUT = 5.5 V 0.0 0.5 5.0 10 mA IOZ IOPD AC ELECTRICAL CHARACTERISTICS Input tr = tf = 3.0 ns TA = 25°C Symbol tPLH, tPHL tPZL, tPZH tPLZ, tPHZ Min TA ≤ 85°C −55 ≤ TA ≤ 125°C Parameter Maximum Propagation Delay, A to Y (Figures 3 and 5.) Typ Max Min Max VCC = 3.3 ± 0.3 V CL = 15pF CL = 50pF 5.6 8.1 8.0 11.5 1.0 1.0 9.5 13.0 12.0 16.0 VCC = 5.0 ± 0.5 V CL = 15pF CL = 50pF 3.8 5.3 5.5 7.5 1.0 1.0 6.5 8.5 8.5 10.5 Maximum Output Enable TIme,OE to Y (Figures 4 and 5) VCC = 3.3 ± 0.3 V RL = RI = 500 W CL = 15pF CL = 50pF 5.4 7.9 8.0 11.5 1.0 1.0 9.5 13.0 11.5 15.0 VCC = 5.0 ± 0.5 V RL = RI = 500 W CL = 15pF CL = 50pF 3.6 5.1 5.1 7.1 1.0 1.0 6.0 8.0 7.5 9.5 Maximum Output Disable Time,OE to Y (Figures 4 and 5) VCC = 3.3 ± 0.3 V RL = RI = 500 W CL = 15pF CL = 50pF 6.5 8.0 9.7 13.2 1.0 1.0 11.5 15.0 14.5 18.0 VCC = 5.0 ± 0.5 V RL = RI = 500 W CL = 15pF CL = 50pF 4.8 7.0 6.8 8.8 1.0 1.0 8.0 10.0 10.0 12.0 10 10 10 Test Conditions Cin Maximum Input Capacitance 4 Cout Maximum Three−State Output Capacitance (Output in High Impedance State) 6 Min Max Unit ns ns ns pF pF Typical @ 25°C, VCC = 5.0 V 14 CPD Power Dissipation Capacitance (Note 5) pF 5. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC / 4 (per buffer). CPD is used to determine the no−load dynamic power consumption; PD = CPD VCC2 fin + ICC VCC. http://onsemi.com 3 MC74VHC1GT125 SWITCHING WAVEFORMS VCC OE 50% VCC GND 50% A tPZL GND tPHL tPLH tPLZ 50% VCC Y 50% VCC tPZH tPHZ Y HIGH IMPEDANCE VOL + 0.3V VOH - 0.3V 50% VCC Y Figure 4. Switching Waveforms TEST POINT TEST POINT OUTPUT DEVICE UNDER TEST HIGH IMPEDANCE Figure 5. DEVICE UNDER TEST CL* *Includes all probe and jig capacitance OUTPUT 1 kW CL * CONNECT TO VCC WHEN TESTING tPLZ AND tPZL. CONNECT TO GND WHEN TESTING tPHZ AND tPZH. *Includes all probe and jig capacitance Figure 6. Test Circuit Figure 7. Test Circuit INPUT Figure 8. Input Equivalent Circuit ORDERING INFORMATION Device M74VHC1GT125DF1G M74VHC1GT125DF2G Package SC−88A / SOT−353 / SC−70 (Pb−Free) M74VHC1GT125DT1G TSOP−5 / SOT−23 / SC−59 (Pb−Free) NLVVHC1GT125DF1G* SC−88A / SOT−353 / SC−70 (Pb−Free) NLVVHC1GT125DF2G* NLVVHC1GT125DT1G* Shipping† 3000/Tape & Reel TSOP−5 / SOT−23 / SC−59 (Pb−Free) †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NLV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable. http://onsemi.com 4 MC74VHC1GT125 PACKAGE DIMENSIONS SC−88A (SC−70−5/SOT−353) CASE 419A−02 ISSUE K A NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419A−01 OBSOLETE. NEW STANDARD 419A−02. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. G 5 4 −B− S 1 2 DIM A B C D G H J K N S 3 D 5 PL 0.2 (0.008) M B M N J C H K http://onsemi.com 5 INCHES MIN MAX 0.071 0.087 0.045 0.053 0.031 0.043 0.004 0.012 0.026 BSC --0.004 0.004 0.010 0.004 0.012 0.008 REF 0.079 0.087 MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.80 1.10 0.10 0.30 0.65 BSC --0.10 0.10 0.25 0.10 0.30 0.20 REF 2.00 2.20 MC74VHC1GT125 PACKAGE DIMENSIONS TSOP−5 CASE 483−02 ISSUE H 2X 0.10 T 2X 0.20 T NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. 5. OPTIONAL CONSTRUCTION: AN ADDITIONAL TRIMMED LEAD IS ALLOWED IN THIS LOCATION. TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2 FROM BODY. D 5X NOTE 5 0.20 C A B M 5 1 4 2 L 3 B S K DETAIL Z G A DIM A B C D G H J K L M S DETAIL Z J C 0.05 SEATING PLANE H T SOLDERING FOOTPRINT* 0.95 0.037 MILLIMETERS MIN MAX 3.00 BSC 1.50 BSC 0.90 1.10 0.25 0.50 0.95 BSC 0.01 0.10 0.10 0.26 0.20 0.60 1.25 1.55 0_ 10 _ 2.50 3.00 1.9 0.074 2.4 0.094 1.0 0.039 0.7 0.028 SCALE 10:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 http://onsemi.com 6 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC74VHC1GT125/D