TI SN74ABT573ADW

SCBS190F − JANUARY 1991 − REVISED SEPTEMBER 2003
2
19
3
18
4
17
5
16
6
15
7
14
8
13
9
12
10
11
VCC
1Q
2Q
3Q
4Q
5Q
6Q
7Q
8Q
LE
1D
2D
3D
4D
5D
6D
7D
8D
20
2D
1D
OE
VCC
1
SN54ABT573 . . . FK PACKAGE
(TOP VIEW)
19 1Q
18 2Q
2
3
3D
4D
5D
6D
7D
17 3Q
16 4Q
4
5
15 5Q
14 6Q
6
7
13 7Q
12 8Q
8
9
10
11
4
3 2 1 20 19
18
5
17
6
16
7
15
8
14
9 10 11 12 13
2Q
3Q
4Q
5Q
6Q
8D
GND
LE
8Q
7Q
20
VCC
1
LE
OE
1D
2D
3D
4D
5D
6D
7D
8D
GND
JEDEC Standard JESD 17
ESD Protection Exceeds JESD 22
− 2000-V Human-Body Model (A114-A)
− 200-V Machine Model (A115-A)
SN74ABT573A . . . RGY PACKAGE
(TOP VIEW)
OE
SN54ABT573 . . . J OR W PACKAGE
SN74ABT573A . . . DB, DW, N, NS,
OR PW PACKAGE
(TOP VIEW)
D
GND
D
D
D Latch-Up Performance Exceeds 500 mA Per
<1 V at VCC = 5 V, TA = 25°C
High-Drive Outputs (−32-mA IOH, 64-mA IOL)
Ioff Supports Partial-Power-Down Mode
Operation
1Q
D Typical VOLP (Output Ground Bounce)
description/ordering information
These 8-bit latches feature 3-state outputs designed specifically for driving highly capacitive or relatively
low-impedance loads. They are particularly suitable for implementing buffer registers, I/O ports, bidirectional
bus drivers, and working registers.
ORDERING INFORMATION
Tube
SN74ABT573AN
SN74ABT573AN
QFN − RGY
Tape and reel
SN74ABT573ARGYR
AB573A
Tube
SN74ABT573ADW
Tape and reel
SN74ABT573ADWR
SOP − NS
Tape and reel
SN74ABT573ANSR
ABT573A
SSOP − DB
Tape and reel
SN74ABT573ADBR
AB573A
Tube
SN74ABT573APW
Tape and reel
SN74ABT573APWR
TSSOP − PW
VFBGA − GQN
VFBGA − ZQN (Pb-free)
−55°C
−55
C to 125
125°C
C
TOP-SIDE
MARKING
PDIP − N
SOIC − DW
−40°C to 85°C
ORDERABLE
PART NUMBER
PACKAGE†
TA
ABT573A
AB573A
SN74ABT573AGQNR
Tape and reel
SN74ABT573AZQNR
AB573A
CDIP − J
Tube
SNJ54ABT573J
SNJ54ABT573J
CFP − W
Tube
SNJ54ABT573W
SNJ54ABT573W
LCCC − FK
Tube
SNJ54ABT573FK
SNJ54ABT573FK
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines
are available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2003, Texas Instruments Incorporated
! "#$ ! %#&'" ($)
(#"! " !%$""! %$ *$ $! $+! !#$!
!(( ,-) (#" %"$!!. ($! $"$!!'- "'#($
$!. '' %$$!)
%(#"! "%' /01
'' %$$! $ $!$(
#'$!! *$,!$ $() '' *$ %(#"!
%(#"
%"$!!. ($! $"$!!'- "'#($ $!. '' %$$!)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SCBS190F − JANUARY 1991 − REVISED SEPTEMBER 2003
description/ordering information (continued)
A buffered output-enable (OE) input can be used to place the eight outputs in either a normal logic state (high
or low logic levels) or the high-impedance state. In the high-impedance state, the outputs neither load nor drive
the bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus
lines without need for interface or pullup components.
OE does not affect the internal operations of the latches. Old data can be retained or new data can be entered
while the outputs are in the high-impedance state.
To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs,
preventing damaging current backflow through the device when it is powered down.
SN74ABT573A . . . GQN OR ZQN PACKAGE
(TOP VIEW)
1
2
3
terminal assignments
4
1
2
3
4
A
A
1D
OE
B
3D
3Q
VCC
2D
1Q
B
C
C
5D
4D
5Q
4Q
D
D
7D
7Q
6D
6Q
E
E
GND
8D
LE
8Q
2Q
FUNCTION TABLE
(each latch)
INPUTS
OE
LE
D
OUTPUT
Q
L
H
H
H
L
H
L
L
L
L
X
Q0
H
X
X
Z
logic diagram (positive logic)
OE
LE
1
11
C1
1D
2
19
1D
To Seven Other Channels
Pin numbers shown are for the DB, DW, FK, J, N, NS, PW, RGY, and W packages.
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1Q
SCBS190F − JANUARY 1991 − REVISED SEPTEMBER 2003
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Voltage range applied to any output in the high or power-off state, VO . . . . . . . . . . . . . . . . . . . −0.5 V to 5.5 V
Current into any output in the low state, IO: SN54ABT573 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 mA
SN74ABT573A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA
Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −18 mA
Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
Package thermal impedance, θJA (see Note 2): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70°C/W
(see Note 2): DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W
(see Note 2): GQN/ZQN package . . . . . . . . . . . . . . . . . . . . . . . . . . . 78°C/W
(see Note 2): N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69°C/W
(see Note 2): NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60°C/W
(see Note 2): PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83°C/W
(see Note 3): RGY package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
2. The package thermal impedance is calculated in accordance with JESD 51-7.
3. The package thermal impedance is calculated in accordance with JESD 51-5.
recommended operating conditions (see Note 4)
SN54ABT573
MAX
MIN
MAX
4.5
5.5
4.5
5.5
VCC
VIH
Supply voltage
VIL
VI
Low-level input voltage
IOH
IOL
High-level output current
VCC
−24
Low-level output current
∆t/∆v
Input transition rise or fall rate
High-level input voltage
SN74ABT573A
MIN
2
2
0.8
Input voltage
0
Outputs enabled
V
V
0.8
0
UNIT
V
VCC
−32
mA
V
48
64
mA
5
5
ns/V
TA
Operating free-air temperature
−55
125
−40
85
°C
NOTE 4: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SCBS190F − JANUARY 1991 − REVISED SEPTEMBER 2003
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
VIK
VOH
TEST CONDITIONS
VCC = 4.5 V,
VCC = 4.5 V,
II = −18 mA
IOH = −3 mA
VCC = 5 V,
VCC = 4.5 V
VOL
VCC = 4.5 V
Vhys
II
TA = 25°C
TYP†
MAX
SN54ABT573
MIN
MAX
−1.2
SN74ABT573A
MIN
−1.2
MAX
−1.2
2.5
2.5
2.5
IOH = −3 mA
IOH = −24 mA
3
3
3
2
2
IOH = −32 mA
IOL = 48 mA
2*
IOL = 64 mA
0.55
0.55*
Ioff
ICEX
IO§
VI = VCC or GND
VO = 2.7 V
VCC = 5.5 V,
VCC = 0,
VO = 0.5 V
VI or VO ≤ 4.5 V
VCC = 5.5 V,
VCC = 5.5 V,
VO = 5.5 V
VO = 2.5 V
0.55
ICC
∆ICC¶
VCC = 5.5 V, One input at 3.4 V,
Other inputs at VCC or GND
Ci
VI = 2.5 V or 0.5 V
VO = 2.5 V or 0.5 V
±1
10‡
−10‡
±100
Outputs high
VCC = 5.5 V, IO = 0,
VI = VCC or GND
V
mV
±1
10‡
−10‡
50
−50
V
2
0.55
VCC = 5.5 V,
VCC = 5.5 V,
UNIT
V
100
IOZH
IOZL
Co
MIN
50
−50
−180
−50
±1
10‡
−10‡
µA
±100
µA
50
µA
−180
mA
µA
µA
−100
−180
Outputs high
1
250
250
250
µA
Outputs low
24
30
30
30
mA
Outputs disabled
0.5
250
250
250
µA
1.5
1.5
1.5
mA
3.5
pF
6.5
pF
* On products compliant to MIL-PRF-38535, this parameter does not apply.
† All typical values are at VCC = 5 V.
‡ This data sheet limit may vary among suppliers.
§ Not more than one output should be tested at a time, and the duration of the test should not exceed one second.
¶ This is the increase in supply current for each input that is at the specified TTL voltage level, rather than VCC or GND.
timing requirements over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (see Figure 1)
SN54ABT573
VCC = 5 V,
TA = 25°C
MIN
4
tw
Pulse duration, LE high
tsu
Setup time, data before LE↓
th
Hold time, data after LE↓
POST OFFICE BOX 655303
MIN
UNIT
MAX
3.3
3.3
High
1.9
2.5
Low
1.5
2.5
1
2.5
• DALLAS, TEXAS 75265
MAX
ns
ns
ns
SCBS190F − JANUARY 1991 − REVISED SEPTEMBER 2003
timing requirements over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (see Figure 1)
SN74ABT573A
VCC = 5 V,
TA = 25°C
MIN
tw
tsu
Pulse duration, LE high
Setup time, data before LE↓
MIN
UNIT
MAX
3.3
3.3
High
1.9
1.9
Low
1.5
1.8†
1.5
1.8†
th
Hold time, data after LE↓
† This data-sheet limit may vary among suppliers.
MAX
ns
ns
ns
switching characteristics over recommended ranges of supply voltage and operating free-air
temperature, CL = 50 pF (unless otherwise noted) (see Figure 1)
SN54ABT573
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
tPLH
tPHL
D
Q
tPLH
tPHL
LE
Q
tPZH
tPZL
OE
Q
tPHZ
tPLZ
OE
Q
VCC = 5 V,
TA = 25°C
MIN
MAX
MIN
TYP
MAX
1.9
3.2
5.4
1.4
6.4
2.2
4.2
5.7
1.6
6.7
2.2
4
6.1
2
7.1
3.2
5.2
6.7
2.8
7.5
1.2
3.2
4.7
0.8
6.2
2.7
4.7
6.2
2
7.2
2.5
4.9
6.4
2.2
7.7
2
4.2
6
1.4
7
UNIT
ns
ns
ns
ns
switching characteristics over recommended ranges of supply voltage and operating free-air
temperature, CL = 50 pF (unless otherwise noted) (see Figure 1)
SN74ABT573A
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
tPLH
tPHL
D
Q
tPLH
tPHL
LE
Q
tPZH
tPZL
OE
Q
tPHZ
tPLZ
OE
Q
VCC = 5 V,
TA = 25°C
MIN
MAX
MIN
TYP
MAX
1.9
3.2
5.4
1.9
5.9
2.2
4.2
5.7
2.2
6.2
2.2
4
6.1
2.2
6.6
3.2
5.2
6.7
3.2
7.2
1.2
2.5†
3.2
4.7
6.2
1.2
2.5†
5.2
4.7
2.5
4.9
6.4
2.5
6.7
7.1†
2
4.2
6
2
6.5
UNIT
ns
ns
ns
ns
† This data-sheet limit may vary among suppliers.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SCBS190F − JANUARY 1991 − REVISED SEPTEMBER 2003
PARAMETER MEASUREMENT INFORMATION
500 Ω
From Output
Under Test
S1
7V
Open
GND
CL = 50 pF
(see Note A)
500 Ω
TEST
S1
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
Open
7V
Open
3V
LOAD CIRCUIT
Timing Input
1.5 V
0V
tw
tsu
3V
th
3V
Input
1.5 V
1.5 V
0V
Data Input
1.5 V
0V
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
VOLTAGE WAVEFORMS
PULSE DURATION
3V
1.5 V
Input
1.5 V
0V
1.5 V
1.5 V
VOL
Output
tPLZ
3.5 V
1.5 V
1.5 V
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
Output
Waveform 2
S1 at Open
(see Note B)
VOL + 0.3 V
VOL
tPHZ
tPZH
VOH
1.5 V
1.5 V
0V
Output
Waveform 1
S1 at 7 V
(see Note B)
tPLH
tPHL
1.5 V
tPZL
VOH
Output
3V
Output
Control
tPHL
tPLH
1.5 V
1.5 V
VOH − 0.3 V
VOH
≈0 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns.
D. The outputs are measured one at a time with one transition per measurement.
E. All parameters and waveforms are not applicable to all devices.
Figure 1. Load Circuit and Voltage Waveforms
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MCFP006B − JANUARY 1995 − REVISED JULY 2003
W (R-GDFP-F20)
CERAMIC DUAL FLATPACK
Base and Seating Plane
0.300 (7,62)
0.245 (6,22)
0.045 (1,14)
0.026 (0,66)
0.009 (0,23)
0.004 (0,10)
0.100 (2,54)
0.045 (1,14)
0.320 (8,13) MAX
1
0.022 (0,56)
0.015 (0,38)
20
0.050 (1,27)
0.540 (13,72)
MAX
0.005 (0,13) MIN
4 Places
10
11
0.370 (9,40)
0.250 (6,35)
0.370 (9,40)
0.250 (6,35)
4040180-4 /D 07/03
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a ceramic lid using glass frit.
Index point is provided on cap for terminal identification only.
Falls within Mil-Std 1835 GDFP2-F20
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
MECHANICAL DATA
MLCC006B – OCTOBER 1996
FK (S-CQCC-N**)
LEADLESS CERAMIC CHIP CARRIER
28 TERMINAL SHOWN
18
17
16
15
14
13
NO. OF
TERMINALS
**
12
19
11
20
10
A
B
MIN
MAX
MIN
MAX
20
0.342
(8,69)
0.358
(9,09)
0.307
(7,80)
0.358
(9,09)
28
0.442
(11,23)
0.458
(11,63)
0.406
(10,31)
0.458
(11,63)
21
9
22
8
44
0.640
(16,26)
0.660
(16,76)
0.495
(12,58)
0.560
(14,22)
23
7
52
0.739
(18,78)
0.761
(19,32)
0.495
(12,58)
0.560
(14,22)
24
6
68
0.938
(23,83)
0.962
(24,43)
0.850
(21,6)
0.858
(21,8)
84
1.141
(28,99)
1.165
(29,59)
1.047
(26,6)
1.063
(27,0)
B SQ
A SQ
25
5
26
27
28
1
2
3
4
0.080 (2,03)
0.064 (1,63)
0.020 (0,51)
0.010 (0,25)
0.020 (0,51)
0.010 (0,25)
0.055 (1,40)
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
0.045 (1,14)
0.035 (0,89)
0.028 (0,71)
0.022 (0,54)
0.050 (1,27)
4040140 / D 10/96
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a metal lid.
The terminals are gold plated.
Falls within JEDEC MS-004
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
MECHANICAL DATA
MPBG133C – APRIL 2000 – REVISED AUGUST 2002
GQN (R-PBGA-N20)
PLASTIC BALL GRID ARRAY
1,95 TYP
3,10
2,90
0,65
0,325
0,65
E
D
4,10
3,90
2,60
C
B
A
1
A1 Corner
2
3
4
Bottom View
1,00 MAX
0,08
Seating Plane
20×
0,45
0,35
0,25
0,15
0,05 M
4200704/D 07/2002
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
MicroStar Juniort configuration
Falls within JEDEC MO-225 variation BC.
This package is tin-lead (SnPb). Refer to the 20 ZQN package (drawing 4204492) for lead-free.
MicroStar Junior is a trademark of Texas Instruments.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
MECHANICAL DATA
MPBG297 – JULY 2002
ZQN (R-PBGA-N20)
PLASTIC BALL GRID ARRAY
1,95
0,65
3,10
2,90
0,325
0,65
E
D
4,10
3,90
2,60
C
B
A
1
2
3
4
Bottom View
A1 Corner
1,00 Max
0,08
Seating Plane
20×
0,45
0,35
0,05 M
0,25
0,15
4204492/A 06/2002
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
MicroStar Junior configuration.
Fall within JEDEC MO-225 variation BC.
This package is lead-free. Refer to the 20 GQN package (drawing 4200704) for tin-lead )SnPb).
MicroStar Junior is a trademark of Texas Instruments.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
MECHANICAL
MPDI002C – JANUARY 1995 – REVISED DECEMBER 20002
N (R-PDIP-T**)
PLASTIC DUAL-IN-LINE PACKAGE
16 PINS SHOWN
PINS **
14
16
18
20
A MAX
0.775
(19,69)
0.775
(19,69)
0.920
(23,37)
1.060
(26,92)
A MIN
0.745
(18,92)
0.745
(18,92)
0.850
(21,59)
0.940
(23,88)
MS-100
VARIATION
AA
BB
AC
DIM
A
16
9
0.260 (6,60)
0.240 (6,10)
1
C
AD
8
0.070 (1,78)
0.045 (1,14)
0.045 (1,14)
0.030 (0,76)
D
D
0.325 (8,26)
0.300 (7,62)
0.020 (0,51) MIN
0.015 (0,38)
Gauge Plane
0.200 (5,08) MAX
Seating Plane
0.010 (0,25) NOM
0.125 (3,18) MIN
0.100 (2,54)
0.430 (10,92) MAX
0.021 (0,53)
0.015 (0,38)
0.010 (0,25) M
14/18 PIN ONLY
20 pin vendor option
D
4040049/E 12/2002
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001, except 18 and 20 pin minimum body lrngth (Dim A).
D. The 20 pin end lead shoulder width is a vendor option, either half or full width.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
MECHANICAL DATA
MSOI003E – JANUARY 1995 – REVISED SEPTEMBER 2001
DW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
16 PINS SHOWN
0.020 (0,51)
0.014 (0,35)
9
0.050 (1,27)
16
0.010 (0,25)
0.419 (10,65)
0.400 (10,15)
0.010 (0,25) NOM
0.299 (7,59)
0.291 (7,39)
Gage Plane
0.010 (0,25)
1
8
0°– 8°
0.050 (1,27)
0.016 (0,40)
A
Seating Plane
0.104 (2,65) MAX
0.012 (0,30)
0.004 (0,10)
PINS **
0.004 (0,10)
16
18
20
24
28
A MAX
0.410
(10,41)
0.462
(11,73)
0.510
(12,95)
0.610
(15,49)
0.710
(18,03)
A MIN
0.400
(10,16)
0.453
(11,51)
0.500
(12,70)
0.600
(15,24)
0.700
(17,78)
DIM
4040000/E 08/01
NOTES: A.
B.
C.
D.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15).
Falls within JEDEC MS-013
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
DB (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
28 PINS SHOWN
0,38
0,22
0,65
28
0,15 M
15
0,25
0,09
8,20
7,40
5,60
5,00
Gage Plane
1
14
0,25
A
0°–ā8°
0,95
0,55
Seating Plane
2,00 MAX
0,10
0,05 MIN
PINS **
14
16
20
24
28
30
38
A MAX
6,50
6,50
7,50
8,50
10,50
10,50
12,90
A MIN
5,90
5,90
6,90
7,90
9,90
9,90
12,30
DIM
4040065 /E 12/01
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-150
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Amplifiers
Applications
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2003, Texas Instruments Incorporated