REVISION BQ DO NOT SCALE FROM THIS PRINT NOTES: 1. REPRESENTS A CRITICAL DIMENSION. C 2. PARTS MAY BE CUT TO POSITION. 3. MAXIMUM CUT FLASH: .010[0.25]. 4. MINIMUM PUSHOUT FORCE: 1.0 LB. 5. TERMINALS TO BE SHEARED TO MEET DIMENSION SPECIFICATION. 6. LAYER PACKAGE 2 - 4 POSITIONS AND TUBE 5 - 50 POSITIONS. 7. MAXIMUM BURR ALLOWANCE: .003[0.08]. 8. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE -EC OPTION IS NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE -EC OPTION. 9. MAXIMUM HEIGHT VARIATION BETWEEN ROWS: .005[0.13]. (No OF POS x .0500[1.270]) - .003[0.08] .006 [0.15] (No OF POS x .0500[1.270]) - .0500[1.270] 50 02 .135 3.43 REF 49 01 No OF POSITIONS -02 THRU -50 (PER ROW) OPTIONS LEAD STYLE -01: .120 [3.05] -02: .075 [1.91] -03: .065 [1.65] -04: .150 [3.81] PLATING SPECIFICATION -G:10µ" GOLD IN CONTACT AREA, 3µ" GOLD ON TAIL -F: 3µ" FLASH SELECTIVE GOLD IN CONTACT AREA, MATTE TIN ON TAIL -L: 10µ" LIGHT SELECTIVE GOLD IN CONTACT AREA, MATTE TIN ON TAIL -S: 30µ" SELECTIVE GOLD IN CONTACT AREA, MATTE TIN ON TAIL -H: 30µ" HEAVY GOLD IN CONTACT AREA, 3µ" GOLD ON TAIL -FM: 3µ" FLASH SELECTIVE GOLD IN CONTACT AREA, MATTE TIN ON TAIL -LM: 10µ" LIGHT SELECTIVE GOLD IN CONTACT AREA, MATTE TIN TAIL -SM: 30µ" HEAVY SELECTIVE GOLD IN CONTACT AREA, MATTE TIN ON TAIL -LTL: 10µ" LIGHT GOLD IN CONACT AREA, TIN/LEAD (90%/10 +/-5%) ON TAIL -ES: END SHROUDS (SEE FIG 2, SHT 2) (MOLDED 5 POS MIN; -02 & -03 LEAD STYLE ONLY) (MUST USE FTSH-XX-ES-XX-X) (SNAP SHROUDS 9 POS MIN; -02 & -03 LEAD STYLE ONLY) (MUST USE FTSH-50-D) -EJ: EJECTOR SHROUDS: (SEE FIG 3, SHT 2) (10 POS MIN; -01 LEAD STYLE ONLY) (MUST USE FTSH-50-D) -EC: LOCKING CLIP (SEE FIG 4, SHT 2; SEE NOTE 8) (9 POS MIN; -02 & -03 LEAD STYLES ONLY) (MUST USE FTSH-50-D) -EP: GUIDE POST (SEE FIG 5, SHT 2) (9 POS MIN; -02 & -03 LEAD STYLES ONLY) (USE ONLY WHEN MATING WITH CLP) (MUST USE FTSH-50-D) -EL: BOARD LOCKS (SEE FIG 6, SHT 2) (9 POS MIN; -02 & -03 LEAD STYLES ONLY) (USE ONLY WHEN MATING WITH CLP) (MUST USE FTSH-50-D) -K: KEYING OPTION FOR MATING WITH FFSD (05 THRU 25 ONLY) (POSITION 13, 17, 20 & 25 AVAILABLE WITH -EJ OPTION) (LEAD STYLE -01 ONLY, SEE FIG 7, SHT 3) (MUST USE FTSH-XX-CN-XX) -LC: LOCKING CLIP: (SEE FIG 8, SHT 3) (5 POS MIN, ONLY AVAILABLE IN -01 LEAD STYLE) (IN COMBINATION WITH -K, USE FTSH-XX-CN-XX, 10 POSITION MINIMUM, ONLY AVAILABLE IN -01 LEAD STYLE) (MUST USE FTSH-50-D) (SINGLE MATING CYCLE ONLY) (MUST BE MATED TO SAMTEC FFSD SERIES) ROW SPECIFICATION -D: DOUBLE ROW (USE **FTSHC-1XX-XX-XXX-D UNLESS OPTION IS SPECIFIED ABOVE. WHEN OPTION IS SPECIFIED, BUILD PER PRINT USING BODY SPECIFIED FOR REQUIRED OPTION) ** = SEE FTSHC-1XX-XX-XXX-DX-XX PRINT FOR DETAILS FTSHC-50-D .0160 0.406 SQ REF (TYP) FTSH-1XX-XX-XXX-D-XX 2 MAX SWAY (EITHER DIRECTION) 2 MAX SWAY (EITHER DIRECTION) C .050 1.27 T-1S15-XX-XXX SEE TABLE 1 "A" C (SEE TABLE 1) (SEE NOTE 9) "A" (SEE TABLE 1) (SEE NOTE 9) .099 2.51 "C" REF (SEE TABLE 1) "B" (SEE TABLE 2) (SEE NOTES 5 & 7) SEE NOTE 3 (2 PLCS) FIG 1 (SEE FTSHC-1XX-XX-XXX-DX-XX-PRINT FOR DETAILS) 2 MAX SWAY (EITHER DIRECTION) IN-PROCESS UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES. TOLERANCES ARE: DECIMALS ANGLES .XX: .01 [.3] 1 .XXX: .005 [.13] .XXXX: .0010 [.025] MATERIAL: PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING INSULATOR: LCD UL 94-V0 TERMINAL: PHOSPHOR BRONZE F:\DWG\MISC\MKTG\FTSH-1XX-XX-XXX-D-XX-MKT.SLDDRW SHEET SCALE: 5:1 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail [email protected] code 55322 DESCRIPTION: .050 x .050 CL THROUGH HOLE TERMINAL STRIP DWG. NO. FTSH-1XX-XX-XXX-D-XX BY: J. FERRY 02/27/1996 SHEET 1 OF 3 REVISION BQ (No OF POS x .050[1.27])+.131[3.32]±.008[0.20] .280 7.11 REF .265 6.73 REF 02 .188 4.78 REF .139 3.53 REF .0699 1.775 01 (No OF POS x .050[1.27])+.101[2.57]±.008[0.20] LC-05-TM FTSH-EC ES-FTSH (No OF POS x .050[1.27])+.079[3.30]±.008[0.20] FIG 4 -EC OPTION (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 2) .178 4.51 (No OF POS x .050[1.27])+.231[5.87]±.008[0.20] FTSH-XX-D FIG 2 -ES OPTION (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1) (-02 OR -03 LEAD STYLE ONLY) (9 POS MIN FOR SNAP SHROUDS) (5 POS MIN FOR MOLDED SHROUDS) (No OF POS x .050[1.27])+.156[3.96] REF .032[0.81] REF CHAMFER .075 1.91 REF FTSH-EP .120 3.05 REF .298 7.56 .096 2.44 REF 02 .175 4.45 REF 01 FIG 5 -EP OPTION (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 2) (USE ONLY WHEN MATING WITH CLP) FTSH-49-ES-XX-X .059 1.49 REF .178 4.51 REF (No OF POS x .050[1.27])+.257[6.53] .125 3.18 REF (No OF POS x .050[1.27])+.153[3.89] FTSH-EL (MOLDED SHROUDS) .293 7.44 REF .303 7.68 FIG 3 USE SUB-FTSH-EJEHA (2 REQ'D PER ASSEMBLY EACH USES 1 EHA-02, 1 FTSH-EJ) -EJ OPTION (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1) (-01 LEAD STYLE ONLY) (No OF POS x .050[1.27])+.223[1.26] FIG 6 -EL OPTION (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 2) (USE ONLY WHEN MATING WITH CLP) POST SIDE OF CONNECTOR .222 5.65 REF .440 11.18 REF PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING .090 2.29 ((No OF POS x .050[1.27]) + .621[15.77])±.010[0.25] F:\DWG\MISC\MKTG\FTSH-1XX-XX-XXX-D-XX-MKT.SLDDRW SHEET SCALE: 2:1 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail [email protected] code 55322 DESCRIPTION: .050 x .050 CL THROUGH HOLE TERMINAL STRIP DWG. NO. FTSH-1XX-XX-XXX-D-XX BY: J. FERRY 02/27/1996 SHEET 2 OF 3 REVISION BQ ((No OF POS x .0500[1.270]) -.003[0.08]±.006[0.15] .085 2.16 REF .200 5.08 REF CL .085 2.16 REF .200 5.08 REF .126 3.20 REF PT-1-24-05-09 FTSH-50-CN-XX PT-1-24-01-43 PT-1-24-11-09 FIG 7 -K OPTION (LEAD STYLE -01) (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1) (POSITION 13, 17, 20 & 25 AVAILABLE WITH -K & -EJ OPTION) LTC-31-01 -01, -02, -03 .428 10.874 REF -04 & -K -EJ, EJ-K, -LC & -LC-K PT-1-24-03-09 PT-1-24-01-55 PT-1-24-01-38 .12 3.1 C .270 6.86 REF (TYP) ((No OF POS x .050[1.27]) + .306[7.77])±.008[0.20] -EC & -EC-K -ES & -ES-K -EL, -EP, -EL-K & -EP-K FIG 9 TUBE VIEWS FIG 8 -LC OPTION (LEAD STYLE -01) (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1) F:\DWG\MISC\MKTG\FTSH-1XX-XX-XXX-D-XX-MKT.SLDDRW PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING SHEET SCALE: 2:1 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail [email protected] code 55322 DESCRIPTION: .050 x .050 CL THROUGH HOLE TERMINAL STRIP DWG. NO. FTSH-1XX-XX-XXX-D-XX BY: J. FERRY 02/27/1996 SHEET 3 OF 3