STMICROELECTRONICS STM32L152-EVAL

STM32L152-EVAL
STM32L152-EVAL evaluation board
Data brief
Features
■
Four 5 V power supply options:
– Power jack
– ST-LINK/V2 USB connector
– User USB connector
– Daughterboard
■
Audio speaker and microphone connected to
DAC and ADC of STM32L152VBT6
■
2 GByte or more SPI interface MicroSD
CardTM
■
I2C compatible serial interface temperature
sensor
■
RS-232 communication
■
IrDA transceiver
■
JTAG and trace debug support, ST-LINK/V2
embedded.
■
240x320 TFT color LCD connected to SPI
interface of STM32L152VBT6
■
Joystick with 4-direction control and selector
■
Reset button
■
Tamper or Key button
■
4 color user LEDs and 3 LEDs as MCU power
range indicator
■
MCU consumption measurement circuit
■
LCD glass 32 x 4 segments connected to LCD
controller in STM32L152VBT6
■
Extension connector for daughterboard or
wrapping board
■
MCU voltage choice of 3.3 V or adjustable from
1.65 V to 3.6 V
■
USB FS connector
■
Two touch sensing buttons
■
Light dependent resistor (LDR)
■
Potentiometer
January 2011
Description
The STM32L152-EVAL evaluation board is a
complete demonstration and development
platform for STMicroelectronics’ ARM cortex-M3
core-based STM32L152VBT6 microcontroller
supporting two I2C, two SPI and three USART
channels, 12-bit ADC, 12-bit DAC, 16 KB internal
SRAM and 128 KB Flash, USB FS, LCD
controller, touch sensing and JTAG debugging
support.
Doc ID 18342 Rev 1
For further information contact your local STMicroelectronics sales office.
1/3
www.st.com
3
Ordering information
1
STM32L152-EVAL evaluation board
Ordering information
Table 1.
Device summary
Order code
Reference
STM32L152-EVAL
2
Revision history
Table 2.
2/3
STM32L152-EVAL evaluation board
Document revision history
Date
Revision
07-Jan-2010
1
Changes
Initial release.
Doc ID 18342 Rev 1
STM32L152-EVAL evaluation board
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2011 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 18342 Rev 1
3/3