AKM AKD4520

ASAHI KASEI
[AK4520A]
AK4520A
100dB 20Bit Stereo ∆Σ ADC & DAC
General Description
The AK4520 is a stereo CMOS A/D & D/A converter for middle-range MD/DAT, Surround System and musical
instruments. Signal inputs and outputs are single-ended. The DAC outputs are analog filtered to remove out of
band noise. External components are minimized.
Features
† ∆Σ Stereo ADC
- 64x Oversampling
- S/(N+D): 90dB at 5V, 86dB at 3V
- Dynamic Range: 100dB at 5V, 96dB at 3V
- S/N: 100dB at 5V, 96dB at 3V
- Digital HPF for offset cancel
† ∆Σ Stereo DAC
- 128x Oversampling
- 2nd order SCF + 2nd order CTF
- Digital de-emphasis for 32kHz, 44.1kHz, 48kHz sampling
- S/(N+D): 90dB at 5V, 90dB at 3V
- Dynamic Range: 100dB at 5V, 96dB at 3V
- S/N: 100dB at 5V, 96dB at 3V
† High Jitter Tolerance
† Sample Rate Ranging from 16kHz to 54kHz
† Master Clock: 256fs or 384fs
† 2.7 to 3.6V or 4.5 to 5.5V supply
† Low Power Dissipation: 255mW
† Small 28pin VSOP Package
0163-E-00
1997/3
-1-
ASAHI KASEI
[AK4520A]
„ Ordering Guide
AK4520A-VF
AKD4520
-10∼+70°C
28pin VSOP
AK4520A Evaluation Board
„ Pin Layout
0163-E-00
1997/3
-2-
ASAHI KASEI
[AK4520A]
PIN/FUNCTION
No.
Pin Name
I/O
Function
Positive Voltage Reference Input Pin, VA
Used as a positive voltage reference by ADC & DAC. VREFH is connected
externally to filtered VA.
Negative Voltage Reference Input Pin, AGND
Used as a negative voltage reference by ADC & DAC. VREFL is connected
externally to AGND.
Rch Analog Positive Input pin
Rch Analog Negative Input Pin
Lch Analog Positive Input pin
Lch Analog Negative Input Pin
Analog Power Supply Pin
Analog Ground pin
Audio Data Interface Format Pin
Audio Data Interface Format Pin
Input/Output Channel Clock Pin
Audio Serial Data Clock Pin
Audio Serial Data Input Pin
Audio Serial Data Output Pin
Master Clock Input Pin
De-emphasis Frequency Select Pin
De-emphasis Frequency Select Pin
Test Pins (Pull down pins)
Must be left open or connected to DGND.
1
VREFH
I
2
VREFL
I
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
AINR+
AINRAINL+
AINLVA
AGND
DIF0
DIF1
LRCK
SCLK
SDTI
SDTO
MCLK
DEM0
DEM1
TST3
TST2
TST1
VD
DGND
PWDA
PWAD
CMODE
I
I
I
I
I
I
I
I
I
O
I
I
I
I/O
I/O
I
I
I
I
26
27
28
AOUTL
AOUTR
VCOM
O
O
O
Digital Power Supply Pin
Digital Ground Pin
DAC Power-Down Mode Pin
ADC Power-Down Mode Pin
Master Clock Select Pin
"H": 384fs, "L": 256fs
Lch analog output pin
Rch analog output pin
Common Voltage Output Pin, VA/2
Note: All input pins except pull-down pins should not be left floating.
0163-E-00
1997/3
-3-
ASAHI KASEI
[AK4520A]
ABSOLUTE MAXIMUM RATINGS
(AGND,DGND=0V; Note 1 )
Parameter
Symbol
min
max
Units
VA
VD
∆GND
-0.3
-0.3
-0.3
-0.3
-10
-65
6.0
6.0
0.3
±10
VA+0.3
VD+0.3
70
150
V
V
V
mA
V
V
°C
°C
Power Supplies:
Analog
Digital
|AGND-DGND|
Input Current, Any Pin Except Supplies
Analog Input Voltage
Digital Input Voltage
Ambient Temperature
(power applied)
Storage Temperature
Note: 1 . All voltages with respect to ground.
IIN
VINA
VIND
Ta
Tstg
WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal
operation is not guaranteed at these extremes.
RECOMMENDED OPERATING CONDITIONS
(AGND,DGND=0V; Note 1 )
Parameter
Power Supplies:
(Note 2 )
3V operation
Analog
Digital
Symbol
min
typ
max
Units
VA
VD
2.7
2.7
3.0
3.0
3.6
VA
V
V
5.0
5.0
5.5
VA
V
V
5V operation
Analog
VA
4.5
Digital
VD
4.5
Note: 1 . All voltages with respect to ground.
2 . The power up sequence between VA and VD is not critical.
0163-E-00
1997/3
-4-
ASAHI KASEI
[AK4520A]
ANALOG CHARACTERISTICS
(Ta=25°C; VA,VD=5.0V; AGND=DGND=0V; VREFH=VA; VREFL=AGND; fs=44.1kHz; SCLK=64fs,
Signal Frequency=1kHz; 20bit Data; Measurement frequency=10Hz∼20kHz; unless otherwise specified)
Parameter
min
typ
max
ADC Analog Input Characteristics: Differential Inputs; Analog Source Impedance=470Ω
Resolution
S/(N+D)
(-0.5dB Input)
20
VA=3V
(Note 3 )
VA=5V
DR (-60dB Input, A-Weighted)
VA=3V
(Note 4 )
VA=5V
S/N
(A-Weighted)
VA=3V
(Note 4 ,5 ) VA=5V
Interchannel Isolation
Interchannel Gain Mismatch
Gain Drift
Input Voltage
VA=3V
AIN=0.6x(VREFH-VREFL)
VA=5V
Input Resistance
Power Supply Rejection
(Note 6 )
80
84
90
94
90
94
90
1.7
2.85
20
86
90
96
100
96
100
110
0.1
20
1.8
3.0
30
50
0.3
1.9
3.15
Units
Bits
dB
dB
dB
dB
dB
dB
dB
dB
ppm/°C
Vpp
Vpp
kΩ
dB
DAC Analog Output Characteristics:
Resolution
S/(N+D)
20
VA=3V
VA=5V
VA=3V
VA=5V
VA=3V
VA=5V
84
80
92
96
92
96
90
90
90
96
100
96
100
110
0.1
20
1.88
3.13
Bits
dB
dB
dB
dB
dB
dB
dB
dB
ppm/°C
DR (-60dB Output, A-Weighted)
(Note 4 )
S/N
(A-Weighted)
(Note 7,5 )
Interchannel Isolation
Interchannel Gain Mismatch
0.3
Gain Drift
Output Voltage
VA=3V
1.76
1.99
Vpp
AOUT=0.626x(VREFH-VREFL)
VA=5V
2.94
3.32
Vpp
kΩ
Load Resistance
10
Load Capacitance
25
pF
Power Supply Rejection
(Note 6 )
50
dB
Note: 3 . In case of single ended input, S/(N+D)=84dB(typ, @VA=5V).
4 . In case of 16bit, DR and S/N of ADC are 98dB. DR of DAC is 98dB.
5 . S/N measured by CCIR-ARM is 96dB at each converter and 94dB at ADC to DAC loopback.
6 . PSR is applied to VA,VD with 1kHz, 50mVpp. VREFH/VREFL pin is held a constant voltage.
7 . As the input data is "0", S/N is 100dB regardless of resolution.
0163-E-00
1997/3
-5-
ASAHI KASEI
[AK4520A]
Parameter
min
typ
max
Units
Power supply Current VA=VD=5V
mA
62
41
PWAD="H",PWDA="H"
Analog
AD+DA
mA
26
17
PWAD="H",PWDA="L"
VA
AD
mA
38
25
PWAD="L",PWDA="H"
DA
Digital
AD+DA
PWAD="H",PWDA="H"
10
15
mA
VD
AD
PWAD="H",PWDA="L"
6
9
mA
(Note 8 ) DA
PWAD="L",PWDA="H"
4
6
mA
VA+VD
Power down PWAD="L",PWDA="L"
0.2
0.4
mA
Note:8 The typical supply current of VD drops to AD+DA=5.5mA, AD=3.5mA, DA=2mA at 3.0V supply
voltage.
FILTER CHARACTERISTICS
(Ta=25°C; VA,VD=2.7∼5.5V; fs=44.1kHz; DEM0="1", DEM1="0")
Parameter
Symbol
min
PB
0
0
0
0
24.34
typ
max
Units
19.76
20.02
20.20
22.05
29.3
0
kHz
kHz
kHz
kHz
kHz
dB
dB
1/fs
us
0.9
2.7
6.0
Hz
Hz
Hz
ADC Digital Filter(Decimation LPF):
Passband
(Note 9 )
-0.005dB
-0.02dB
-0.06dB
-6.0dB
Stopband
Passband Ripple
Stopband Attenuation
Group Delay
(Note 10 )
Group Delay Distortion
SB
PR
SA
GD
∆GD
±0.005
80
ADC Digital Filter(HPF):
Frequency Response (Note 9 ) -3dB
-0.5dB
-0.1dB
FR
DAC Digital Filter:
Passband
(Note 9 )
Stopband
Passband Ripple
Stopband Attenuation
Group Delay
-0.06dB
-6.0dB
(Note 10 )
PB
0
0
24.1
SB
PR
SA
GD
20.0
22.05
±0.06
43
14.7
kHz
kHz
kHz
dB
dB
1/fs
DAC Digital Filter+Analog Filter:
Frequency Response 0∼20.0kHz
±0.1
FR
dB
Notes: 9. The Passband and stopband frequencies scale with fs. For example, 20.02kHz at -0.02dB is
0.454 x fs.
10. The calculating delay time which occurred by digital filtering. This time is from the input of analog
signal to setting the 20bit data of both channels to the output register for ADC.
For DAC, this time is from setting the 20bit data of both channels on input register to the output of
analog signal.
0163-E-00
1997/3
-6-
ASAHI KASEI
[AK4520A]
DIGITAL CHARACTERISTICS
(Ta=25°C; VA,VD=2.7∼5.5V)
Parameter
High-Level Input Voltage
Low-Level Input Voltage
High-Level Output Voltage (Iout=-100uA)
Low-Level Output Voltage (Iout=100uA)
Input Leakage Current
Symbol
min
typ
max
Units
VIH
VIL
VOH
VOL
Iin
70%VD
VD-0.5
-
-
30%VD
0.5
±10
V
V
V
V
uA
typ
max
Unit
13.824
MHz
ns
ns
MHz
ns
ns
kHz
SWITCHING CHARACTERISTICS
(Ta=25°C; VA,VD=2.7∼5.5V; CL=20pF)
Parameter
Master Clock Timing
LRCK Frequency
256fs:
Pulse Width Low
Pulse Width High
384fs:
Pulse Width Low
Pulse Width High
VD=2.7-3.6V
VD=4.5-5.5V
(Note 11 )
Duty Cycle
Serial Interface Timing
SCLK Period
SCLK Pulse Width Low
Pulse Width High
LRCK Edge to SCLK "↑" (Note 12 )
SCLK "↑" to LRCK Edge (Note 12 )
LRCK to SDTO(MSB)
SCLK "↓" to SDTO
SDTI Hold Time
SDTI Setup Time
Reset Timing
PWAD & PWDA Pulse Width
PWAD "↑" to SDTO valid (Note 13 )
Symbol
fCLK
tCLKL
tCLKH
fCLK
tCLKL
tCLKH
fs
fs
tSCK
tSCKL
tSCKH
tLRS
tSLR
tLRM
tSSD
tSDH
tSDS
min
4.096
27
27
6.144
20
20
16
16
45
20.736
44.1
44.1
50
54
55
289.4
120
120
30
30
100
100
40
40
%
ns
ns
ns
ns
ns
ns
ns
ns
ns
tPW
150
ns
tPWV
516
1/fs
Notes: 11.If the duty cycle of LRCK changes larger than 5 to 50%, the AK4520A is reset by the internal phase
circuit automatically.
12.SCLK rising edge must not occur at the same time as LRCK edge.
13.These cycles are the number of LRCK rising from PWAD rising.
0163-E-00
1997/3
-7-
ASAHI KASEI
[AK4520A]
„ Timing Diagram
0163-E-00
1997/3
-8-
ASAHI KASEI
[AK4520A]
OPERATION OVERVIEW
„ System Clock Input
The AK4520A with CMODE is used to select either MCLK=256fs or 384fs. The relationship between the
external clock applied to the MCLK input and the desired sample rate is defined in Table 1 . The LRCK clock
input must be synchronized with MCLK, however the phase is not critical. Internal timing is synchronized to
LRCK upon power-up or when the internal timing becomes out of phase. All external clocks must be present
unless both PWDA and PWAD ="L", otherwise excessive current may result from abnormal operation of
internal dynamic logic.
MCLK
SCLK
fs
256fs
CMODE="L"
32.0kHz
44.1kHz
48.0kHz
8.1920MHz
12.2880MHz
2.048MHz
11.2896MHz
16.9344MHz
2.822MHz
12.2880MHz
18.4320MHz
3.072MHz
Table 1 . System Clock Example
384fs
CMODE="H"
64fs
32fs
1.0240MHz
1.4112MHz
1.5360MHz
„ Audio Serial Interface Format
Data is shifted in/out the SDTI/SDTO pins using SCLK and LRCK inputs. Four serial data modes are
supported selected by the DIF0 and DIF1 pins as shown in Table 2 . In all modes the serial data is MSB-first,
2's compliment format is clocked on the falling edge of SCLK. For mode 3, if SCLK is 32fs, then the least
significant bits will be truncated.
Mode
DIF1
DIF0
SDTO(ADC)
SDTI(DAC)
L/R
SCLK
0
0
0
20bit, MSB justified
16bit, LSB justified
H/L
≥32fs
1
0
1
20bit, MSB justified
20bit, LSB justified
H/L
≥40fs
2
1
0
20bit, MSB justified
20bit, MSB justifie
H/L
≥40fs
3
1
1
IIS(I2S)
IIS(I2S)
L/H
32fs or
≥40fs
Table 2 . Serial Data Modes
0163-E-00
1997/3
-9-
ASAHI KASEI
[AK4520A]
0163-E-00
1997/3
- 10 -
ASAHI KASEI
[AK4520A]
„ Digital High Pass Filter
The ADC of AK4520A has a digital high pass filter for DC offset cancel. The cut-off frequency of the HPF is
0.9Hz at fs=44.1kHz and also scales with sampling rate(fs).
„ De-emphasis filter
The DAC of AK4520A includes the digital de-emphasis filter(tc=50/15us) by IIR filter. This filter corresponds to
three frequencies (32kHz,44.1kHz,48kHz). The de-emphasis filter selected by DEM0 and DEM1 is enabled for
input audio data. The de-emphasis is also disabled at DEM0="1" and DEM1="0".
DEM 1
DEM0
Mode
0
0
44.1kHz
0
1
OFF
1
0
48kHz
1
1
32kHz
Table 3 . De-emphasis filter control
0163-E-00
1997/3
- 11 -
ASAHI KASEI
[AK4520A]
„ Power-Down & Reset
The ADC and DAC of AK4520A are placed in the power-down mode by bringing each power down pin, PWAD
PWDA "L" independently and each digital filter is also reset at the same time. This reset should always be done
after power-up. In case of the ADC, an analog initialization cycle starts after exiting the power-down mode.
Therefore, the output data, SDTO becomes available after 516 cycles of LRCK clock. This initialization cycle
does not affect the DAC operation.
Figure 5 shows the power-up sequence when the DAC is powered up before the ADC power-up.
1
{
2
{
{
4
{
3
5
{
6
{
The analog part of ADC is initialized after exiting the power-down state.
Digital output corresponding to analog input and analog output corresponding to digital input have
the group delay(GD).
A/D output is "0" data at the power-down state.
Click noise occurs at the end of initialization of the analog part. Please mute the digital output
externally if the click noise influences system application. Required muting time depends on the
configuration of the input buffer circuits.
Figure 6: 1s
Figure 9: 200ms
Click noise occurs at the edge of PWDA.
5 ) influences system application.
Please mute the analog output externally if the click noise({
Figure 5 . Power-up sequence
0163-E-00
1997/3
- 12 -
ASAHI KASEI
[AK4520A]
SYSTEM DESIGN
Figure 6 shows the system connection diagram. This is an example which analog signal is input by single
ended circuit. In case of differential input, please refer to Figure 9 . An evaluation board is available which
demonstrates application circuits, the optimum layout, power supply arrangements and measurement results.
0163-E-00
1997/3
- 13 -
ASAHI KASEI
[AK4520A]
Figure 8 . Power Supply Arrangement
1. Grounding and Power Supply Decoupling
The AK4520A requires careful attention to power supply and grounding arrangements. VA and VD are usually
supplied from analog supply in system. Alternatively if VA and VD are supplied separately, the power up
sequence is not critical. AGND and DGND of the AK4520A should be connected to analog ground plane.
System analog ground and digital ground should be connected together near to where the supplies are
brought onto the printed circuit board. Decoupling capacitors should be as near to the AK4520A as possible,
with the small value ceramic capacitor being the nearest.
0163-E-00
1997/3
- 14 -
ASAHI KASEI
[AK4520A]
2. On-chip voltage reference
The differential Voltage between VREFH and VREFL sets the analog input/output range. VREFH pin is
normally connected to VA with a 0.1uF ceramic capacitor and VREFL pin is connected to AGND. VCOM is a
signal ground of this chip. An electrolytic capacitor 10uF parallel with a 0.1uF ceramic capacitor attached to
VCOM pin eliminates the effects of high frequency noise. No load current may be drawn from VCOM pin. All
signals, especially clocks, should be kept away from the VREFH,VREFL and VCOM pins in order to avoid
unwanted coupling into the AK4520A.
3. Analog Inputs
The ADC inputs are differential and internally biased to the common voltage(VA/2) with 30kΩ (typ) resistance.
Figure 6 is a circuit example which analog signal is input by single end. the signal can be input from either
positive or negative input and the input signal range scales with the supply voltage and nominally 0.6 x
(VREFH-VREFL) Vpp. In case of single ended input, the distortion around full scale degrades compared with
differential input. Figure 9 is a circuit example which analog signal is input to both positive and negative input
and the input signal range scales with the supply voltage and nominally 0.3 x (VREFH-VREFL) Vpp. The
AK4520A can accept input voltages from AGND to VA. The ADC output data format is 2's complement The
output code is 7FFFFH(@20bit) for input above a positive full scale and 80000H(@20bit) for input below a
negative full scale. The ideal code is 00000H(@20bit) with no input signal. The DC offset is removed by the
internal HPF.
The AK4520A samples the analog inputs at 64fs. The digital filter rejects noise above the stop band except for
multiples of 64fs. A simple RC filter(fc=150kHz) may be used to attenuate any noise around 64fs and most
audio signals do not have significant energy at 64fs.
The AK4520A has tone noise with around -110dB on the ADC output. There are two methods of dropping VD
to 3V or adding a small DC offset at the ADC input to reduce the noise level. The evaluation board(AKD4520)
manual should be referred about the detail.
Figure 9 . Differential Input Buffer Example
0163-E-00
1997/3
- 15 -
ASAHI KASEI
[AK4520A]
4. Analog Outputs
The analog outputs are also single-ended and centered around the VCOM voltage. The input signal range
scales with the supply voltage and nominally 0.626 x (VREFH-VREFL) Vpp. The DAC input data format is 2's
complement. The output voltage is a positive full scale for 7FFFFH(@20bit) and a negative full scale for
80000H(@20bit). The ideal output is VCOM voltage for 00000H(@20bit). The internal switched-capacitor filter
and continuous-time filter removes most of the noise generated by the delta-sigma modulator of DAC beyond
the audio passband.
DC offsets on analog outputs are eliminated by AC coupling since DAC outputs have DC offsets of a few mV.
Figure 10 shows the example of external op-amp circuit with 6dB gain. The output signal is inverted by using
the circuit in this case.
Figure 10 . External analog circuit example(gain=6dB)
0163-E-00
1997/3
- 16 -
ASAHI KASEI
[AK4520A]
PACKAGE
z 28pin VSOP (Unit: mm)
„ Material & Lead finish
Package molding compound:
Lead frame material:
Lead frame surface treatment:
Epoxy
Cu
Solder plate
0163-E-00
1997/3
- 17 -
ASAHI KASEI
[AK4520A]
MARKING
XXXBYYYYC date code identifier
XXXB: Lot number(X:Digit number, B:Alpha character)
YYYYC: Assembly date(Y:Digit number,C:Alpha character)
0163-E-00
1997/3
- 18 -
IMPORTANT NOTICE
zThese products and their specifications are subject to change without notice. Before
considering any use or application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM)
sales office or authorized distributor concerning their current status.
zAKM assumes no liability for infringement of any patent, intellectual property, or other
right in the application or use of any information contained herein.
zAny export of these products, or devices or systems containing them, may require an
export license or other official approval under the law and regulations of the country of
export pertaining to customs and tariffs, currency exchange, or strategic materials.
zAKM products are neither intended nor authorized for use as critical components in any
safety, life support, or other hazard related device or system, and AKM assumes no
responsibility relating to any such use, except with the express written consent of the
Representative Director of AKM. As used here:
(a) A hazard related device or system is one designed or intended for life support or
maintenance of safety or for applications in medicine, aerospace, nuclear energy, or
other fields, in which its failure to function or perform may reasonably be expected to
result in loss of life or in significant injury or damage to person or property.
(b) A critical component is one whose failure to function or perform may reasonably be
expected to result, whether directly or indirectly, in the loss of the safety or
effectiveness of the device or system containing it, and which must therefore meet
very high standards of performance and reliability.
zIt is the responsibility of the buyer or distributor of an AKM product who distributes,
disposes of, or otherwise places the product with a third party to notify that party in
advance of the above content and conditions, and the buyer or distributor agrees to
assume any and all responsibility and liability for and hold AKM harmless from any and
all claims arising from the use of said product in the absence of such notification.