AWT6103M5 Cellular Dual Mode AMPS/TDMA Mode 3.5V/30 dBm Linear Power Amplifier Module Advanced Product Information Rev. 1 • • • • • • • • • • FEATURES InGaP HBT Technology High Efficiency 50% AMPS High Efficiency 45% TDMA Low Leakage Current (<25µA) SMT Module Package Small Foot Print (6mm x 6mm) Low Profile (1.6mm) 50 Ω Input and Output Matching Low Quiescent Current (ICQ 50mA Typ) Shut Down and Mode Control APPLICATIONS • Dual Mode AMP/TDMA Handsets 6x6mm Module Package Description The AWT6103 is a 3.5V power amplifier module for use in Dual Mode AMPS/TDMA handsets. Absolute Minimum and Maximum Ratings S IGNAL MIN MAX UNITS +5 V Input Power (RF IN ) +10 dBm Bias Voltage (V REF ) +3.5 V Supply Voltage (Vcc ) V M O D Voltage (V MOD ) +3.5 V Storage Temperature (T STG ) -55 100 °C Operating Temperature (T C ) -25 80 °C AWT6103M5 Electrical Specifications AMPS: (Unless otherwise specified: Vcc = 3.5V, Z = Z IN Parameter Minimal OUT =50Ω System, TC = 25 °C) Typical Maximum Units 849 MHz Frequency Range 824 Supply Voltage Range 3.0 3.5 5.0 V Ref voltage Range 2.75 2.8 2.9 V Ref current 2 mA Output Power, V CC = 3.5V 32.0 dBm Output Power, V CC = 3.0V 31.0 dBm Input Impedance 2:1 Output Impedance 2:1 Efficiency Pout = 32 dBm 50 % Icq (V MODE = 2.7V) Low Power Mode 50 mA Noise at Receiver Band P OUT ≤ 32 dbm -90 dBm/30 kHz Gain, P OUT= 32 dBm 26 dB Leakage Current V CC = 3.5V; V REF = 0V ; V MODE = 2.7V 25 µA Harmonics 2fo, P OUT = 32 dBm -30 dBc 3fo, P OUT = 32 dBm -30 dBc Stability (out of band load VSWR < 20:1) (in band load VSWR < 10:1) -60 Ruggedness Stress for no permanent degradation or failure, VCC = 5.0 V 10:1 Bias Table 2 Power Range POUT Levels 50 mA All 0-32 dBm AMP All Power 50 mA Low 0-22 dBm NADC Low Power 100 mA High 22-30 dBm NADC High Power V MODE V ICQ Typ High 2.7 High 2.7 Low 0 Mode dBc, all spurious Pin - 50 dBm … +0 dBm AWT6103M5 Electrical Specifications (TDMA 824-849 MHz) (Unless otherwise specified: Vcc = 3.5V, Z = Z =50Ω System, TC = 25 °C) IN Parameter Minimum OUT Typical Maximum Units Frequency Range 824 849 MHz Supply Voltage Range 3.0 3.5 5.0 V Ref. Voltage Range 2.75 2.8 2.9 V Ref. Current 2 mA Output Power, V CC = 3.5V 30 dBm Output Power, V CC = 3.0V 29 dBm Input VSWR 2:1 Output VSWR 2:1 Power Added Efficiency Pout = 30 dBm Power Added Efficiency Pout = 16 dBm (V MODE = 2.7V) Low Power Mode Icq (V MODE = 2.7V) Low Power Mode 45 % 7 % 50 mA Linearity (P OUT avg. = 30 dBm) & V CC =3.5V NADC - modulation ACPR +/- 30 kHz -28 dBc ACPR +/- 60 kHz -48 dBc ACPR +/- 90 kHz -50 dBc Noise at Receiver Band Pout ≤30 dbm -90 dBm/30 kHz Gain, P OUT = 30 dBm 25 28 31 Leakage current V CC =3.5V ; V MODE =2.7V ; V REF = 0V 25 µA Harmonics 2fo, P OUT = 30 dBm -30 dBc 3fo, P OUT = 30 dBm -30 dBc Stability (out of band load VSWR < 20:1) (in band load VSWR < 10:1) Ruggedness Stress for no permanent degradation or failure, V CC = 5.0 V -60 dBc, all spurious Pin - 50 dBm … +0 dBm 10:1 3 AWT6103M5 Pin Description P in Name 1 V CC D e s c r ip t i o n Supply Voltage 2 R F IN R F In p u t S i g n a l 3 V REF Bias 4 V MODE M o d e C o n trol 5 V CC 6 R F OUT Supply Voltage RF output 7 GND Ground Package Outline Top View 6.0 ANADIGICS, Inc. 35 Technology Drive Warren, New Jersey 07059 Tel: (908) 668-5000 Fax: (908) 668-5132 http://www.anadigics.com [email protected] IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or discontinue any product at any time without notice. The Advanced Product data sheets and product specifications contained in this data sheet are subject to change prior to a products formal introduction. The information in this data sheet has been carefully checked and is assumed to be reliable. However, ANADIGICS assumes no responsibility for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices, or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 4