F S4560 Semiconductor Dual high slew rate OP AMP Description The S4560 is dual operational amplifiers which achieve approximately twice the high output current of the S4560, as well as featuring a higher slew rate of 4V/us, a gain band width of 10MHz, and an improved frequency characteristic. Features • • • • • Built-in output short-circuit protection circuit. Internal phase correction. No latch-up Wide same phase mode and differential voltage ranges High gain. low noise Applications • • • • Active filters Audio amplifiers VCOs Other electronic circuits Ordering Information Type NO. S4560 Marking Package Code S4560 SOP-8 Outline Dimensions unit : mm Block Diagram KSI-K004-001 1 S4560 Absolute maximum ratings Ta = 25 °C Characteristic Symbol Ratings Unit Supply voltage VCC ±18 V Differential input voltage VID ±30 V Input voltage VIC -Vcc~Vcc V Power Dissipation PD* 550 mW Operating temperature Topr -40 ~ +85 °C Storage temperature Tstg -55 ~ +125 °C * Refer to Pd characteristics diagram. The values for the S4560 are those when it is mounted on a glass epoxy PCB(50 ㎜×50 ㎜×1.6 ㎜). Electrical Characteristics (Unless otherwise specified. VCC = +15V, VEE=－15V and Characteristic Symbol Input offset voltage VIOS Input offset current IIOS Input bias current Ta = 25 °C) Test Condition Rg ≤ 10 ㏀ Min. Typ. Max. Unit - 0.5 6 mV - - 5 200 nA IIB - - 50 500 nA Input common mode Voltage Range VICR - ±12 ±14 - V ±14 VOM RL≥ 10 ㏀ ±12 Maximum Output Voltage - V RL≥ 2 ㏀ ±10 ±13 - V Vout=±10V, RL≥ 2 ㏀ 86 100 - dB Large signal Voltage Gain GV Common mode rejection ratio CMRR Rg ≤ 10 ㏀ 70 90 - dB Power supply rejection ratio PSRR Rg ≤ 10 ㏀ - 30 150 uV/V GV=1, RL≥ 2 ㏀ - 4.0 - V/us - - 2.2 uV - 10 - MHz Slew Rate SR Input conversion noise voltage Vn Gain band width product GBW f=10kHz KSI-K004-001 2 S4560 Electrical Characteristic Curves Fig. 1 GV – f Fig. 2 VOP-P – f (Vcc/VEE=±15V,RL=2 ㏀,Ta=25℃) (Vcc/VEE=±15V,Ta=25℃) ㏀ Fig. 4 VICR - VCC / VEE Fig. 3 IIB - Ta (Ta=25℃) (Vcc/VEE=±15V) / Fig. 5 IQ - VCC / V EE ± Fig. 6 IIB - VCC (Ta=25℃) (Ta=25℃) / KSI-K004-001 3 S4560 These AUK products are intended for usage in general electronic equipments(Office and communication equipment, measuring equipment, domestic electrification, etc.). Please make sure that you consult with us before you use these AUK products in equipments which require high quality and/or reliability, and in equipments which could have major impact to the welfare of human life(atomic energy control, airplane, spaceship, traffic signal, combustion central, all types of safety device, etc.). AUK cannot accept liability to any damage which may occur in case these AUK products were used in the mentioned equipments without prior consultation with AUK. KSI-K004-001 4