ADS8402 SLAS154B – DECEMBER 2002 – REVISED MAY 2003 16-BIT, 1.25 MSPS, UNIPOLAR DIFFERENTIAL INPUT, MICRO POWER SAMPLING ANALOG-TO-DIGITAL CONVERTER WITH PARALLEL INTERFACE AND REFERENCE FEATURES APPLICATIONS D DWDM D Instrumentation D High-Speed, High-Resolution, Zero Latency D 1.25-MHz Sample Rate D 16-Bit NMC Ensured Over Temperature Data Acquisition Systems D Zero Latency D Onboard Reference D Transducer Interface D Medical Instruments D Communication D Onboard Reference Buffer DESCRIPTION D High-Speed Parallel Interface The ADS8402 is a 16-bit, 1.25 MHz A/D converter with an internal 4.096-V reference. The device includes a 16-bit capacitor-based SAR A/D converter with inherent sample and hold. The ADS8402 offers a full 16-bit interface and an 8-bit option where data is read using two 8-bit read cycles. D Unipolar Differential Input Range: Vref to –Vref D Power Dissipation: 155 mW at 1.25 MHz Typ D Wide Digital Supply D 8-/16-Bit Bus Transfer The ADS8402 has a unipolar differential input. It is available in a 48-lead TQFP package and is characterized over the industrial –40°C to 85°C temperature range. D 48-Pin TQFP Package SAR +IN –IN + _ Output Latches and 3-State Drivers CDAC BYTE 16-/8-Bit Parallel DATA Output Bus Comparator RESET REFIN REFOUT 4.096-V Internal Reference Clock Conversion and Control Logic CONVST BUSY CS RD Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright 2002–2003, Texas Instruments Incorporated ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ORDERING INFORMATION MODEL MAXIMUM INTEGRAL LINEARITY (LSB) ADS8402I ADS8402IB MAXIMUM DIFFERENTIAL LINEARITY (LSB) ±6 ±3 5 ±3.5 –2~+3 2 3 –1~+2 1 2 NO MISSING CODES RESOLUTION (BIT) PACKAGE TYPE 15 48 Pin TQFP 16 48 Pin TQFP PACKAGE DESIGNATOR TEMPERATURE RANGE PFB –40 C to –40°C 85°C PFB –40 C to –40°C 85°C ORDERING INFORMATION TRANSPORT MEDIA QUANTITY ADS8402IPFBT Tape and reel 250 ADS8402IPFBR Tape and reel 1000 ADS8402IBPFBT Tape and reel 250 ADS8402IBPFBR Tape and reel 1000 NOTE: For the most current specifications and package information, refer to our website at www.ti.com. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted(1) UNIT +IN to AGND Voltage Voltage range +VA + 0.1 V –IN to AGND +VA + 0.1 V +VA to AGND –0.3 V to 7 V +VBD to BDGND –0.3 V to 7 V +VA to +VBD –0.3 V to 2.5 V Digital input voltage to BDGND –0.3 V to +VBD + 0.3 V Digital output voltage to BDGND –0.3 V to +VBD + 0.3 V Operating free-air temperature range, TA –40°C to 85°C Storage temperature range, Tstg –65°C to 150°C Junction temperature (TJ max) Power dissipation TQFP package θJA thermal impedance Vapor phase (60 sec) Lead temperature, temperature soldering Infrared (15 sec) 150°C (TJMax – TA)/θJA 86°C/W 215°C 220°C (1) Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2 ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 SPECIFICATIONS TA = –40°C to 85°C, +VA = 5 V, +VBD = 3 V or 5 V, Vref = 4.096 V, fSAMPLE = 1.25 MHz (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Analog Input Full-scale input voltage (see Note 1) +IN – –IN Absolute input voltage Common-mode input range +IN –Vref –0.2 –IN –0.2 ADS8402I (Vref/2) – 0.2 Input capacitance Input leakage current Vref Vref + 0.2 Vref + 0.2 Vref/2 25 (Vref/2) + 0.2 V V V pF 0.5 nA 16 Bits System Performance Resolution No missing codes ADS8402I 15 ADS8402IB 16 –6 ±2.5 6 –3.5 ±2 3.5 ADS8402I –2 ±1 3 ADS8402IB –1 ±0.75 2 ADS8402I Integral linearity (see Notes 2 and 3) Differentiallinearity Differential linearity ADS8402IB ADS8402I Offset error (see Note 4) ADS8402IB ADS8402I Gain error (see Notes 4 and 5) Common mode rejection ratio Common-mode ADS8402IB LSB LSB –3 ±1 3 mV –1.5 ±0.5 1.5 mV –0.15 0.15 –0.098 0.098 At dc (±0.2 V around Vref/2) 80 +IN – –IN = 1 Vpp at 1 MHz 80 Noise DC Power supply rejection ratio Bits At 7FFFh output code, +VA = 4.75 V to 5.25 V, Vref = 4.096 V, See Note 4 %FS dB 60 µV RMS 1 LSB Sampling Dynamics Conversion time Acquisition time ns 1.25 MHz 150 ns Throughput rate Aperture delay 610 2 ns Aperture jitter 25 ps Step response 100 ns 100 ns Overvoltage recovery (1) Ideal input span, does not include gain or offset error. (2) LSB means least significant bit (3) This is endpoint INL, not best fit (4) Measured relative to an ideal full-scale input (+IN – –IN) of 8.192 V (5) This specification does not include the internal reference voltage error and drift. 3 ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 SPECIFICATIONS (CONTINUED) TA = –40°C to 85°C, +VA = +5 V, +VBD = 3 V or 5 V, Vref = 4.096 V, fSAMPLE = 1.25 MHz (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Dynamic Characteristics Total harmonic distortion (THD) (see Note 1) Signal-to-noise ratio (SNR) Signal-to-noise + distortion (SINAD) Spurious free dynamic range (SFDR) VIN = 8 Vpp at 100 kHz VIN = 8 Vpp at 100 kHz –95 dB 90 dB VIN = 8 Vpp at 100 kHz VIN = 8 Vpp at 100 kHz 88 dB 95 dB 5 MHz –3dB Small signal bandwidth External Voltage Reference Input Reference voltage at REFIN, Vref 2.5 Reference resistance (see Note 2) 4.096 4.2 500 V kΩ Internal Reference Output Internal reference start-up time From 95% (+VA), with 1 µF storage capacity 4.065 4.096 120 ms 4.13 V Vref range Source Current IOUT = 0 Line Regulation +VA = 4.75 ~ 5.25 V 0.6 mV Drift IOUT = 0 36 PPM/C Static load 10 µA Digital Input/Output CMO S Logic family L i level Logic l l VIH VIL IIH = 5 µA IIL = 5 µA VOH VOL IOH = 2 TTL loads IOL = 2 TTL loads +VBD–1 +VBD + 0.3 –0.3 0.8 +VBD – 0.6 +VBD 0 0.4 V 2’s Complement Data format Power Supply Requirements P Power supply l voltage lt +VBD (see Notes 3 and 4) 2.95 3.3 5.25 V +VA (see Note 4) 4.75 5 5.25 V 31 34 +VA Supply current (see Note 5) Power dissipation (see Note 5) fs = 1.25 MHz fs = 1.25 MHz 155 mA mW Temperature Range Operating free-air –40 85 (1) Calculated on the first nine harmonics of the input frequency (2) Can vary ±20% (3) The difference between +VA and +VBD should not be less than 2.3 V, i.e., if +VA is 5.25 V, +VBD should be minimum of 2.95 V. (4) +VBD ≥ +VA – 2.3 V (5) This includes only VA+ current. +VBD current is typically 1 mA with 5 pF load capacitance on output pins. 4 °C ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 TIMING CHARACTERISTICS All specifications typical at –40°C to 85°C, +VA = +VBD = 5 V (see Notes 1, 2, and 3) PARAMETER tCONV tACQ Conversion time tpd1 tpd2 CONVST low to conversion started (BUSY high) tw1 tsu1 Pulse duration, CONVST low tw2 Pulse duration, CONVST high Acquisition time MIN TYP MAX UNIT 600 610 ns 150 Propagation delay time, End of conversion to BUSY low Setup time, CS low to CONVST low th1 Pulse duration, BUSY signal low 20 ns ns 0 ns 20 ns 10 Min(tACQ) Pulse duration, BUSY signal high Hold time, First data bus data transition (RD low, or CS low for read cycle, or BYTE input changes) after CONVST low ns 20 CONVST falling edge jitter tw3 tw4 ns 35 ps ns 630 ns 40 ns 0 ns 0 ns 50 ns td1 tsu2 Delay time, CS low to RD low tw5 ten Pulse duration, RD low time td2 td3 Delay time, data hold from RD high 0 Delay time, BYTE rising edge or falling edge to data valid 2 tw6 th2 RD high 20 ns Hold time, last RD (or CS for read cycle ) rising edge to CONVST falling edge 50 ns tpd4 tsu3 Propagation delay time, BUSY falling edge to next RD (or CS for read cycle) falling edge Max(td5) 0 ns th3 Hold time, BYTE falling edge to RD falling edge 0 ns tdis Disable time, RD High (CS high for read cycle) to 3-stated data bus Setup time, RD high to CS high Enable time, RD low (or CS low for read cycle) to data valid Setup time, BYTE rising edge to RD falling edge 20 td5 Delay time, BUSY low to MSB data valid (1) All input signals are specified with tr = tf = 5 ns (10% to 90% of +VBD) and timed from a voltage level of (VIL + VIH)/2. (2) See timing diagrams. (3) All timings are measured with 20 pF equivalent loads on all data bits and BUSY pins. ns ns 20 ns ns 20 ns 0 ns 5 ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 TIMING CHARACTERISTICS All specifications typical at –40°C to 85°C, +VA = 5 V, +VBD = 3 V (see Notes 1, 2, and 3) PARAMETER tCONV tACQ Conversion time tpd1 tpd2 CONVST low to conversion started (BUSY high) tw1 tsu1 Pulse duration, CONVST low tw2 Pulse duration, CONVST high Acquisition time MIN TYP MAX UNIT 600 610 ns 150 Propagation delay time, end of conversion to BUSY low Setup time, CS low to CONVST low th1 Pulse duration, BUSY signal low 20 ns ns 0 ns 20 ns 10 Min(tACQ) Pulse duration, BUSY signal high Hold time, first data bus transition (RD low, or CS low for read cycle, or BYTE or BUS 16/16 input changes) after CONVST low ns 20 CONVST falling edge jitter tw3 tw4 ns 40 ps ns 630 ns 40 ns 0 ns 0 ns 50 ns td1 tsu2 Delay time, CS low to RD low tw5 ten Pulse duration, RD low td2 td3 Delay time, data hold from RD high 0 Delay time, BUS16/16 or BYTE rising edge or falling edge to data valid 2 tw6 th2 Pulse duration, RD high time 20 ns Hold time, last RD (or CS for read cycle ) rising edge to CONVST falling edge 50 ns tpd4 tsu3 Propagation delay time, BUSY falling edge to next RD (or CS for read cycle) falling edge Max(td5) ns Setup time, BYTE rising edge to RD falling edge 0 ns th3 Hold time, BYTE falling edge to RD falling edge 0 ns tdis Disable time, RD High (CS high for read cycle) to 3-stated data bus Setup time, RD high to CS high Enable time, RD low (or CS low for read cycle) to data valid 30 td5 Delay time, BUSY low to MSB data valid delay time (1) All input signals are specified with tr = tf = 5 ns (10% to 90% of +VBD) and timed from a voltage level of (VIL + VIH)/2. (2) See timing diagrams. (3) All timings are measured with 10 pF equivalent loads on all data bits and BUSY pins. 6 ns ns 30 ns 30 ns 0 ns ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 PIN ASSIGNMENTS BUSY BDGND +VBD DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 BDGND PFB PACKAGE (TOP VIEW) 36 35 34 33 32 31 30 29 28 27 26 25 37 24 38 23 39 22 40 21 41 20 42 19 43 18 44 17 45 16 46 15 47 14 48 3 4 5 6 7 8 13 9 10 11 12 REFIN REFOUT NC +VA AGND +IN –IN AGND +VA +VA 1 2 +VBD DB8 DB9 DB10 DB11 DB12 DB13 DB14 DB15 AGND AGND +VA AGND AGND +VBD RESET BYTE CONVST RD CS +VA AGND AGND +VA REFM REFM NC – No connection 7 ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 TERMINAL FUNCTIONS NAME AGND BDGND NO. I/O 5, 8, 11, 12, 14, 15, 44, 45 – Analog ground DESCRIPTION 25, 35 – Digital ground for bus interface digital supply BUSY 36 O Status output. High when a conversion is in progress. BYTE 39 I Byte select input. Used for 8-bit bus reading. 0: No fold back 1: Low byte D[7:0] of the 16 most significant bits is folded back to high byte of the 16 most significant pins DB[15:8]. CONVST 40 I Convert start CS 42 I Chip select 8-Bit Bus D t B Data Bus BYTE = 0 16-Bit Bus BYTE = 1 BYTE = 0 DB15 16 O D15 (MSB) D7 D15 (MSB) DB14 17 O D14 D6 D14 DB13 18 O D13 D5 D13 DB12 19 O D12 D4 D12 DB11 20 O D11 D3 D11 DB10 21 O D10 D2 D10 DB9 22 O D9 D1 D9 DB8 23 O D8 D0 (LSB) D8 DB7 26 O D7 All ones D7 DB6 27 O D6 All ones D6 DB5 28 O D5 All ones D5 DB4 29 O D4 All ones D4 DB3 30 O D3 All ones D3 DB2 31 O D2 All ones D2 DB1 32 O D1 All ones D1 DB0 33 O D0 (LSB) All ones D0 (LSB) –IN 7 I Inverting input channel +IN 6 I Non inverting input channel NC 3 – No connection REFIN 1 I Reference input REFM 47, 48 I Reference ground REFOUT 2 O Reference output. Add 1 µF capacitor between the REFOUT pin and REFM pin when internal reference is used. RESET 38 I Current conversion is aborted and output latches are cleared (set to zeros) when this pin is asserted low. RESET works independantly of CS. RD 41 I Synchronization pulse for the parallel output. +VA 4, 9, 10, 13, 43, 46 – Analog power supplies, 5-V dc 24, 34, 37 – Digital power supply for bus +VBD 8 ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 TIMING DIAGRAMS tw2 tw1 CONVST tpd1 tpd2 tw4 tw3 BUSY tsu1 CS CONVERT† t(CONV) t(CONV) SAMPLING† (When CS Toggle) t(ACQ) BYTE th1 tsu2 tpd4 th2 td1 RD tdis ten DB[15:8] Hi–Z Hi–Z D [15:8] DB[7:0] Hi–Z D [7:0] Hi–Z D [7:0] †Signal internal to device Figure 1. Timing for Conversion and Acquisition Cycles With CS and RD Toggling 9 ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 tw1 tw2 CONVST tpd1 tpd2 tw4 tw3 BUSY tsu1 CS CONVERT† t(CONV) t(CONV) SAMPLING† (When CS Toggle) t(ACQ) BYTE th1 tpd4 th2 RD = 0 ten DB[15:8] DB[7:0] Hi–Z Hi–Z tdis D [15:8] D [7:0] D [7:0] Hi–Z Hi–Z †Signal internal to device Figure 2. Timing for Conversion and Acquisition Cycles With CS Toggling, RD Tied to BDGND 10 ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 tw1 tw2 CONVST tpd1 tpd2 tw4 tw3 BUSY CS = 0 CONVERT† t(CONV) t(CONV) t(ACQ) SAMPLING† (When CS = 0) BYTE th1 tpd4 th2 RD tdis ten DB[15:8] DB[7:0] Hi–Z Hi–Z D [15:8] D [7:0] D [7:0] Hi–Z Hi–Z †Signal internal to device Figure 3. Timing for Conversion and Acquisition Cycles With CS Tied to BDGND, RD Toggling 11 ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 tw2 tw1 CONVST tpd1 tpd2 tw4 tw3 BUSY CS = 0 CONVERT† t(CONV) t(CONV) t(ACQ) SAMPLING† (When CS = 0) BYTE th1 RD = 0 th1 tdis td3 td5 DB[15:8] Previous D [7:0] Next D [15:8] D [7:0] D [15:8] DB[7:0] Next D [7:0] D [7:0] †Signal internal to device Figure 4. Timing for Conversion and Acquisition Cycles With CS and RD Tied to BDGND—Auto Read CS RD BYTE ten tdis tdis ten DB[15:0] td3 Hi–Z Valid Hi–Z Valid Valid Figure 5. Detailed Timing for Read Cycles 12 Hi–Z ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 TYPICAL CHARACTERISTICS† HISTOGRAM (DC Code Spread) NEAR POSITIVE FULL SCALE 196608 CONVERSIONS SIGNAL-TO-NOISE RATIO vs FREE-AIR TEMPERATURE 120000 fi = 50 kHz (+IN– –IN) = Full Scale +VA = 5 V, Code = 61383 SNR – Signal-To- Noise Ratio – dB 100000 90.9 80000 60000 40000 20000 61385 61383 61380 90.7 90.6 90.5 90.4 90.3 –40 0 Figure 6 90.8 SFDR – Spurious Free-Dynamic Range – dB SINAD – Signal-To-Noise Plus Distortion – dB 102 fi = 50 kHz (+IN– –IN) = Full Scale 90 89.8 89.6 89.4 89.2 –25 –10 5 20 35 50 65 TA – Free-Air Temperature – °C Figure 8 80 SPURIOUS FREE-DYNAMIC RANGE vs FREE-AIR TEMPERATURE 90.4 89 –40 –10 5 20 35 50 65 TA – Free-Air Temperature – °C Figure 7 SIGNAL-TO-NOISE PLUS DISTORTION vs FREE-AIR TEMPERATURE 90.2 –25 80 101 fi = 50 kHz (+IN– –IN) = Full Scale 100 99 98 97 96 95 94 –40 –20 0 20 40 60 80 TA – Free-Air Temperature – °C Figure 9 † At –40°C to 85°C, +VA = 5 V, +VBD = 5 V, REFIN = 4.096 V (internal reference used) and fsample = 1.25 MHz (unless otherwise noted) 13 ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 TOTAL HARMONIC DISTORTION vs FREE-AIR TEMPERATURE SIGNAL-TO-NOISE RATIO vs INPUT FREQUENCY 92 91.8 –95 SNR – Signal-To- Noise Ratio – dB THD – Total Harmonic Distortion – dB –94 –96 –97 –98 –99 –100 fi = 50 kHz (+IN– –IN) = Full Scale –101 –102 –40 –25 –10 5 20 35 50 TA = 25°C (+IN– –IN) = Full Scale 91.6 91.4 91.2 91 90.8 90.6 90.4 90.2 90 65 89.8 80 0 20 TA – Free-Air Temperature – °C Figure 10 60 14.9 TA = 25°C (+IN– –IN) = Full Scale Vref = 4.096 V 14.85 14.8 14.75 ENOB – Bit 90.5 90 89.5 14.7 14.65 14.6 14.55 14.5 89 14.45 14.4 88.5 0 20 40 60 80 fi – Input Frequency – kHz Figure 12 100 0 20 40 60 80 fi – Input Frequency – kHz Figure 13 † At –40°C to 85°C, +VA = 5 V, +VBD = 5 V, REFIN = 4.096 V (internal reference used) and fsample = 1.25 MHz (unless otherwise noted) 14 100 ENOB vs INPUT FREQUENCY 91.5 91 80 Figure 11 SIGNAL-TO-NOISE PLUS DISTORTION vs INPUT FREQUENCY SINAD – Signal-To-Noise Plus Distortion – dB 40 fi – Input Frequency – kHz 100 ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 SPURIOUS FREE-DYNAMIC RANGE vs INPUT FREQUENCY TOTAL HARMONIC DISTORTION vs INPUT FREQUENCY –94 TA = 25°C (+IN– –IN) = Full Scale 100 THD – Total Harmonic Distortion – dB SFDR – Spurious Free-Dynamic Range – dB 101 99 98 97 96 95 TA = 25°C (+IN– –IN) = Full Scale –95 –96 –97 –98 –99 –100 94 –101 0 20 40 60 80 fi – Input Frequency – kHz 0 100 Figure 14 0.0073 TA = 25°C Current of +VA only 0.0061 TA = 25°C External Reference = 4.096 V (REFIN) 0.0048 31 EG – Gain Error – %FS I CC – Supply Current – mA 100 GAIN ERROR vs SUPPLY VOLTAGE 32 30.5 30 29.5 0.0036 0.0024 0.0012 29 0 28.5 –0.0012 28 250 40 60 80 fi – Input Frequency – kHz Figure 15 SUPPLY CURRENT vs SAMPLE RATE 31.5 20 500 750 1000 Sample Rate – KSPS Figure 16 1250 –0.0024 4.75 5 +VA – Supply Voltage – V 5.25 Figure 17 † At –40°C to 85°C, +VA = 5 V, +VBD = 5 V, REFIN = 4.096 V (internal reference used) and fsample = 1.25 MHz (unless otherwise noted) 15 ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 INTERNAL REFERENCE VOLTAGE vs FREE-AIR TEMPERATURE OFFSET ERROR vs SUPPLY VOLTAGE 0.25 Vref – Internal Reference Voltage – V 4.098 EO – Offset Error – mV 0.2 0.15 0.1 TA = 25°C External Reference = 4.096 V (REFIN) 0.05 0 4.75 5 +VA – Supply Voltage – V 4.096 4.094 4.092 4.090 4.088 –40 5.25 –25 –10 5 20 35 50 65 80 TA – Free-Air Temperature – °C Figure 18 Figure 19 OFFSET ERROR vs FREE-AIR TEMPERATURE GAIN ERROR vs FREE-AIR TEMPERATURE 0.018 0.6 0.4 0.012 EO – Offset Error – mV EG – Gain Error – %FS 0.2 0.006 0 0 –0.2 –0.4 –0.6 –0.006 –0.8 External Reference = 4.096 V (REFIN) –0.012 –40 –25 –10 5 20 35 50 65 TA – Free-Air Temperature – °C Figure 20 External Reference = 4.096 V (REFIN) 80 –1 –40 –25 –10 5 20 35 50 65 TA – Free-Air Temperature – °C 80 Figure 21 † At –40°C to 85°C, +VA = 5 V, +VBD = 5 V, REFIN = 4.096 V (internal reference used) and fsample = 1.25 MHz (unless otherwise noted) 16 ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 DIFFERENTIAL NONLINEARITY (MAX) vs FREE-AIR TEMPERATURE SUPPLY CURRENT vs FREE-AIR TEMPERATURE 1.4 DNL – Differential Nonlinearity (Max) – LSB 30.75 I CC – Supply Current – mA 30.70 30.65 30.60 30.55 30.50 30.45 30.40 30.35 30.30 –40 External Reference = 4.096 V (REFIN) Current of +VA only –25 –10 5 20 35 50 65 1.2 1 0.8 0.6 0.4 External Reference = 4.096 V (REFIN) 0.2 0 –40 80 –25 TA – Free-Air Temperature – °C Figure 22 –10 5 20 35 50 65 TA – Free-Air Temperature – °C 80 Figure 23 DIFFERENTIAL NONLINEARITY (MIN) vs FREE-AIR TEMPERATURE INTEGRAL NONLINEARITY (MAX) vs FREE-AIR TEMPERATURE 3 –0.68 –0.69 INL – Integral Nonlinearity (MAX) – LSB DNL – Differential Nonlinearity (MIN) – LSB External Reference = 4.096 V (REFIN) –0.70 –0.71 –0.72 –0.73 –0.74 –0.75 –0.76 2.5 2 1.5 1 External Reference = 4.096 V (REFIN) 0.5 –0.77 –0.78 –40 –25 –10 5 20 35 50 65 TA – Free-Air Temperature – °C Figure 24 80 0 –40 –25 –10 5 20 35 50 65 TA – Free-Air Temperature – °C 80 Figure 25 † At –40°C to 85°C, +VA = 5 V, +VBD = 5 V, REFIN = 4.096 V (internal reference used) and fsample = 1.25 MHz (unless otherwise noted) 17 ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 INTEGRAL NONLINEARITY vs REFERENCE VOLTAGE INTEGRAL NONLINEARITY (MIN) vs FREE-AIR TEMPERATURE 3.0 0 2.5 INL – Integral Nonlinearity – LSB INL – Integral Nonlinearity (MIN) – LSB External Reference = 4.096 V (REFIN) –0.5 –1 –1.5 –2 Max 2.0 1.5 1.0 +VA = +VBD = 5 V, TA = 25°C 0.5 0.0 –0.5 Min –1.0 –1.5 –2.0 –2.5 –40 –25 –10 5 20 35 50 65 TA – Free-Air Temperature – °C –2.5 2.0 80 2.5 3.0 3.5 4.0 Vref – Reference Voltage – V Figure 26 Figure 27 DIFFERENTIAL NONLINEARITY vs REFERENCE VOLTAGE 3.5 +VA = +VBD = 5 V, TA = 25°C DNL – Differential Nonlinearity – LSB 3.0 2.5 2.0 Max 1.5 1.0 0.5 0.0 Min –0.5 –1.0 2.0 2.5 3.0 3.5 4.0 Vref – Reference Voltage – V 4.5 Figure 28 † At –40°C to 85°C, +VA = 5 V, +VBD = 5 V, REFIN = 4.096 V (internal reference used) and fsample = 1.25 MHz (unless otherwise noted) 18 4.5 ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 DNL – LSB DNL 2.5 2 1.5 1 0.5 0 –0.5 –1 –1.5 –2 –2.5 32768 16384 0 49152 65536 49152 65536 Code TA = 25°C, External Reference = 4.096 V (REFIN) Figure 29 INL 5 4 INL – LSB 3 2 1 –0 –1 –2 –3 –4 –5 0 16384 32768 Code TA = 25°C, External Reference = 4.096 V (REFIN) Figure 30 FFT SPECTRUM RESPONSE Magnitude – dB of Full Scale 0 –20 –40 –60 –80 –100 –120 –140 –160 –180 –200 0 100 32768 Points, fS = 1.25 MHz, Internal Reference = 4.096 V (REFIN), TA = 25°C, fi = 100 kHz, (+IN– –IN) = Full Scale 200 300 400 500 600 Frequency – kHz Figure 31 † At –40°C to 85°C, +VA = 5 V, +VBD = 5 V, REFIN = 4.096 V (internal reference used) and fsample = 1.25 MHz (unless otherwise noted) 19 ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 APPLICATION INFORMATION MICROCONTROLLER INTERFACING ADS8402 to 8-Bit Microcontroller Interface Figure 32 shows a parallel interface between the ADS8402 and a typical microcontroller using the 8-bit data bus. The BUSY signal is used as a falling-edge interrupt to the microcontroller. Analog 5 V 0.1 µF AGND 10 µF Ext Ref Input 0.1 µF 1 µF Micro Controller –IN +VA REFIN REFM AGND +IN Analog Input Digital 3 V ADS8402 GPIO CS GPIO P[7:0] BYTE DB[15:8] RD CONVST BUSY RD GPIO INT 0.1 µF BDGND BDGND +VBD Figure 32. ADS8402 Application Circuitry (using external reference) Analog 5 V 0.1 µF AGND 10 µF 0.1 µF AGND REFM REFIN REFOUT +VA 1 µF ADS8402 Figure 33. Use Internal Reference 20 AGND ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 PRINCIPLES OF OPERATION The ADS8402 is a high-speed successive approximation register (SAR) analog-to-digital converter (ADC). The architecture is based on charge redistribution, which inherently includes a sample/hold function. See Figure 32 for the application circuit for the ADS8402. The conversion clock is generated internally. The conversion time of 610 ns is capable of sustaining a 1.25-MHz throughput. The analog input is provided to two input pins: +IN and –IN. When a conversion is initiated, the differential input on these pins is sampled on the internal capacitor array. While a conversion is in progress, both inputs are disconnected from any internal function. REFERENCE The ADS8402 can operate with an external reference with a range from 2.5 V to 4.2 V. A 4.096-V internal reference is included. When internal reference is used, pin 2 (REFOUT) should be connected to pin 1 (REFIN) with an 0.1 µF decoupling capacitor and 1 µF storage capacitor between pin 2 (REFOUT) and pins 47 and 48 (REFM) (see Figure 33). The internal reference of the converter is double buffered. If an external reference is used, the second buffer provides isolation between the external reference and the CDAC. This buffer is also used to recharge all of the capacitors of the CDAC during conversion. Pin 2 (REFOUT) can be left unconnected (floating) if external reference is used. ANALOG INPUT When the converter enters the hold mode, the voltage difference between the +IN and –IN inputs is captured on the internal capacitor array. Both +IN and –IN input has a range of –0.2 V to Vref + 0.2 V. The input span (+IN – (–IN)) is limited to –Vref to Vref. The input current on the analog inputs depends upon a number of factors: sample rate, input voltage, and source impedance. Essentially, the current into the ADS8402 charges the internal capacitor array during the sample period. After this capacitance has been fully charged, there is no further input current. The source of the analog input voltage must be able to charge the input capacitance (25 pF) to an 16-bit settling level within the acquisition time (150 ns) of the device. When the converter goes into the hold mode, the input impedance is greater than 1 GΩ. Care must be taken regarding the absolute analog input voltage. To maintain the linearity of the converter, the +IN and –IN inputs and the span (+IN – (–IN)) should be within the limits specified. Outside of these ranges, the converter’s linearity may not meet specifications. To minimize noise, low bandwidth input signals with low-pass filters should be used. Care should be taken to ensure that the output impedance of the sources driving +IN and –IN inputs are matched. If this is not observed, the two inputs could have different setting time. This may result in offset error, gain error and linearity error which varies with temperature and input voltage. A typical input circuit using TI’s THS4503 is shown in Figure 34. Input from a single-ended source may be converted into differential signal for ADS8402 as shown in the figure. In case the source itself is differential then THS4503 may be used in differential input and differential output mode. 21 ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 68 pF RS RG RT 1 kΩ 50 Ω VCC+ + _ 20 pF THS4503 IN– ADS8402 _ + + _ IN+ OCM VCC– 1 kΩ 1 kΩ 50 Ω 68 pF RG, RS, and RT should be chosen such that RG + RS || RT = 1 k Ω VOCM = 2 V, +VCC = 7 V, and –VCC = –7 V Figure 34. Using THS4503 With ADS8402 DIGITAL INTERFACE Timing and Control See the timing diagrams in the specifications section for detailed information on timing signals and their requirements. The ADS8402 uses an internal oscillator generated clock which controls the conversion rate and in turn the throughput of the converter. No external clock input is required. Conversions are initiated by bringing the CONVST pin low for a minimum of 20 ns (after the 20 ns minimum requirement has been met, the CONVST pin can be brought high), while CS is low. The ADS8402 switches from the sample to the hold mode on the falling edge of the CONVST command. A clean and low jitter falling edge of this signal is important to the performance of the converter. The BUSY output is brought high after CONVST goes low. BUSY stays high throughout the conversion process and returns low when the conversion has ended. Sampling starts with the falling edge of the BUSY signal when CS is tied low or starts with the falling edge of CS when BUSY is low. Both RD and CS can be high during and before a conversion with one exception (CS must be low when CONVST goes low to initiate a conversion). Both the RD and CS pins are brought low in order to enable the parallel output bus with the conversion. Reading Data The ADS8402 outputs full parallel data in two’s complement format as shown in Table 1. The parallel output is active when CS and RD are both low. There is a minimal quiet zone requirement around the falling edge of CONVST. This is 100 ns prior to the falling edge of CONVST and 40 ns after the falling edge. No data read should be attempted within this zone. Any other combination of CS and RD sets the parallel output to 3-state. BYTE is used for multiword read operations. BYTE is used whenever lower bits of the conversion result are output on the higher byte of the bus. Refer to Table 1 for ideal output codes. 22 ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 Table 1. Ideal Input Voltages and Output Codes DESCRIPTION ANALOG VALUE FULL SCALE RANGE Least significant bit (LSB) DIGITAL OUTPUT TWOS COMPLEMENT 2Vref 2Vref/65536 BINARY CODE HEX CODE 0111 1111 1111 1111 7FFF Midscale Vref 0 0000 0000 0000 0000 0000 Zero –Vref 1000 0000 0000 0000 8000 Full scale The output data is a full 16-bit word (D15–D0) on DB15–DB0 pins (MSB–LSB) if BYTE is low. The result may also be read on an 8-bit bus for convenience. This is done by using only pins DB15–DB8. In this case two reads are necessary: the first as before, leaving BYTE low and reading the 8 most significant bits on pins DB15–DB8, then bringing BYTE high. When BYTE is high, the low bits (D7–D0) appears on pins DB15–D8. These multiword read operations can be done with multiple active RD (toggling) or with RD tied low for simplicity. DATA READ OUT BYTE DB15–DB8 DB7–DB0 High D7–D0 All one’s Low D15–D8 D7–D0 RESET RESET is an asynchronous active low input signal (that works independantly of CS). Minimum RESET low time is 20 ns. Current conversion will be aborted no later than 50 ns after the converter is in the reset mode. In addition, all output latches are cleared (set to zero’s) after RESET. The converter goes back to normal operation mode no later than 20 ns after RESET input is brought high. The converter starts the first sampling period 20 ns after the rising edge of RESET. Any sampling period except for the one immediately after a RESET is started with the falling edge of the previous BUSY signal or the falling edge of CS, whichever is later. POWER-ON INITIALIZATION One RESET pulse followed by three conversion cycles must be given to the converter after powerup to ensure proper operation. The next pulse can be issued once both +VA and +VBD reach 95% of the minimum required value. LAYOUT For optimum performance, care should be taken with the physical layout of the ADS8402 circuitry. As the ADS8402 offers single-supply operation, it is often used in close proximity with digital logic, microcontrollers, microprocessors, and digital signal processors. The more digital logic present in the design and the higher the switching speed, the more difficult it is to achieve good performance from the converter. The basic SAR architecture is sensitive to glitches or sudden changes on the power supply, reference, ground connections and digital inputs that occur just prior to latching the output of the analog comparator. Thus, driving any single conversion for an n-bit SAR converter, there are at least n windows in which large external transient voltages can affect the conversion result. Such glitches might originate from switching power supplies, nearby digital logic, or high power devices. The degree of error in the digital output depends on the reference voltage, layout, and the exact timing of the external event. On average, the ADS8402 draws very little current from an external reference, as the reference voltage is internally buffered. If the reference voltage is external and originates from an op amp, make sure that it can drive the bypass capacitor or capacitors without oscillation. A 0.1-µF bypass capacitor and 1-µF storage capacitor are recommended from pin 1 (REFIN) directly to pin 48 (REFM). REFM and AGND should be shorted on the same ground plane under the device. 23 ADS8402 www.ti.com SLAS154B – DECEMBER 2002 – REVISED MAY 2003 The AGND and BDGND pins should be connected to a clean ground point. In all cases, this should be the analog ground. Avoid connections which are close to the grounding point of a microcontroller or digital signal processor. If required, run a ground trace directly from the converter to the power supply entry point. The ideal layout consists of an analog ground plane dedicated to the converter and associated analog circuitry. As with the AGND connections, +VA should be connected to a 5-V power supply plane or trace that is separate from the connection for digital logic until they are connected at the power entry point. Power to the ADS8402 should be clean and well bypassed. A 0.1-µF ceramic bypass capacitor should be placed as close to the device as possible. See Table 2 for the placement of the capacitor. In addition, a 1-µF to 10-µF capacitor is recommended. In some situations, additional bypassing may be required, such as a 100-µF electrolytic capacitor or even a Pi filter made up of inductors and capacitors—all designed to essentially low-pass filter the 5-V supply, removing the high frequency noise. Table 2. Power Supply Decoupling Capacitor Placement POWER SUPPLY PLANE SUPPLY PINS CONVERTER ANALOG SIDE CONVERTER DIGITAL SIDE Pin pairs that require shortest path to decoupling capacitors (4,5), (8,9), (10,11), (13,15), (43,44), (45,46) (24,25), (34, 35) Pins that require no decoupling 12, 14 37 24 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third–party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2003, Texas Instruments Incorporated