ADS8405 SLAS427 – DECEMBER 2004 16-BIT, 1.25-MSPS, UNIPOLAR PSEUDO-DIFFERENTIAL INPUT, MICROPOWER SAMPLING ANALOG-TO-DIGITAL CONVERTER WITH PARALLEL INTERFACE FEATURES APPLICATIONS • • • • • • • • • • • • • • • Unipolar Pseudo-Differential Input, 0 V to Vref 16-Bit NMC at 1.25 MSPS ±2 LSB INL Max, -1/+1.5 LSB DNL 86 dB SNR, -90 dB THD at 100 kHz Input Zero Latency Internal 4.096-V Reference High-Speed Parallel Interface Single 5-V Analog Supply Wide I/O Supply: 2.7 V to 5.25 V Low Power: 155 mW at 1.25 MHz Typ Pin Compatible With ADS8411/8401 48-Pin TQFP Package • • • DWDM Instrumentation High-Speed, High-Resolution, Zero Latency Data Acquisition Systems Transducer Interface Medical Instruments Communications DESCRIPTION The ADS8405 is a 16-bit, 1.25-MHz A/D converter with an internal 4.096-V reference. The device includes a 16-bit capacitor-based SAR A/D converter with inherent sample and hold. The ADS8405 offers a full 16-bit interface and an 8-bit option where data is read using two 8-bit read cycles if necessary. The ADS8405 has a unipolar pseudo-differential input. It is available in a 48-lead TQFP package and is characterized over the industrial -40°C to 85°C temperature range. High Speed SAR Converter Family Type/Speed 18-Bit Pseudo-Diff 500 kHz ~600 kHz ADS8383 750 kHz 1 MHz 1.25 MHz 2 MHz 3 MHz 4 MHz ADS8381 ADS8380 (S) 18-Bit Pseudo-Bipolar, Fully Diff ADS8382 (S) 16-Bit Pseudo-Diff ADS8401/05 ADS8411 16-Bit Pseudo-Bipolar, Fully Diff ADS8371 ADS8402/06 ADS8412 14-Bit Pseudo-Diff ADS7890 (S) 12-Bit Pseudo-Diff ADS7891 ADS7886 SAR +IN −IN + _ CDAC ADS7881 Output Latches and 3-State Drivers BYTE 16-/8-Bit Parallel DATA Output Bus Comparator REFIN REFOUT 4.096-V Internal Reference Clock Conversion and Control Logic RESET CONVST BUSY CS RD Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2004, Texas Instruments Incorporated ADS8405 www.ti.com SLAS427 – DECEMBER 2004 ORDERING INFORMATION (1) MODEL MAXIMUM INTEGRAL LINEARITY (LSB) MAXIMUM DIFFERENTIAL LINEARITY (LSB) NO MISSING CODES RESOLUTION (BIT) PACKAGE TYPE PACKAGE DESIGNATOR TEMPERATURE RANGE ADS8405I –4 to +4 –2 to +2 15 48 Pin TQFP PFB –40°C to 85°C ADS8405IB (1) –2 to +2 –1 to +1.5 16 48 Pin TQFP PFB ORDERING INFORMATION TRANSPORT MEDIA QUANTITY ADS8405IPFBT Tape and reel 250 ADS8405IPFBR Tape and reel 1000 ADS8405IBPFBT Tape and reel 250 ADS8405IBPFBR Tape and reel 1000 –40°C to 85°C For the most current specifications and package information, refer to our website at www.ti.com. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted (1) UNIT Voltage +IN to AGND –0.4 V to +VA + 0.1 V –IN to AGND –0.4 V to 0.5 V +VA to AGND –0.3 V to 7 V +VBD to BDGND +VA to +VBD –0.3 V to 7 V –0.3 V to 2.55 V Digital input voltage to BDGND –0.3 V to +VBD + 0.3 V Digital output voltage to BDGND –0.3 V to +VBD + 0.3 V TA Operating free-air temperature range –40°C to 85°C Tstg Storage temperature range –65°C to 150°C Junction temperature (TJ max) TQFP package Power dissipation θJA thermal impedance Lead temperature, soldering (1) 2 150°C (TJMax – TA)/θJA 86°C/W Vapor phase (60 sec) 215°C Infrared (15 sec) 220°C Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. ADS8405 www.ti.com SLAS427 – DECEMBER 2004 SPECIFICATIONS TA = –40°C to 85°C, +VA = 5 V, +VBD = 3 V or 5 V, Vref = 4.096 V, fSAMPLE = 1.25 MHz (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT ANALOG INPUT Full-scale input voltage (1) +IN – (–IN) Absolute input voltage 0 Vref +IN –0.2 Vref + 0.2 –IN –0.2 0.2 V V Input capacitance 25 pF Input leakage current 0.5 nA 16 Bits SYSTEM PERFORMANCE Resolution No missing codes (2) (3) INL Integral linearity DNL Differential linearity EO Offset error (4) 15 ADS8405IB 16 ADS8405I –4 ±2 4 ADS8405IB –2 ±1 2 ADS8405I –2 ±1 2 ADS8405IB –1 ±0.75 1.5 ADS8405I –3 ±1 3 mV –1.5 ±0.5 1.5 mV ADS8405IB ADS8405I Gain error (4) (5) EG ADS8405I ADS8405IB –0.15 0.15 –0.098 0.98 Noise DC Power supply rejection ratio Bits At FFFFh output code, +VA = 4.75 V to 5.25 V, Vref = 4.096 V (4) LSB LSB %FS 60 µV RMS 2 LSB SAMPLING DYNAMICS Conversion time 500 Acquisition time 150 650 ns 1.25 MHz ns Throughput rate Aperture delay 2 ns Aperture jitter 25 ps Step response 100 ns Overvoltage recovery 100 ns VIN = 4 Vp-p at 100 kHz –90 dB VIN = 4 Vp-p at 500 kHz –88.5 dB DYNAMIC CHARACTERISTICS THD Total harmonic distortion (6) SNR Signal-to-noise ratio VIN = 4 Vp-p at 100 kHz 86 dB SINAD Signal-to-noise + distortion VIN = 4 Vp-p at 100 kHz 85 dB VIN = 4 Vp-p at 100 kHz 90 dB VIN = 4 Vp-p at 500 kHz 88 dB 5 MHz SFDR Spurious free dynamic range -3dB Small signal bandwidth EXTERNAL VOLTAGE REFERENCE INPUT Reference voltage at REFIN, Vref Reference resistance (1) (2) (3) (4) (5) (6) (7) (7) 2.5 4.096 500 4.2 V kΩ Ideal input span, does not include gain or offset error. LSB means least significant bit This is endpoint INL, not best fit. Measured relative to an ideal full-scale input (+IN – (–IN)) of 4.096 V. This specification does not include the internal reference voltage error and drift. Calculated on the first nine harmonics of the input frequency. Can vary ±20% 3 ADS8405 www.ti.com SLAS427 – DECEMBER 2004 SPECIFICATIONS (continued) TA = –40°C to 85°C, +VA = 5 V, +VBD = 3 V or 5 V, Vref = 4.096 V, fSAMPLE = 1.25 MHz (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 120 ms INTERNAL REFERENCE OUTPUT Internal reference start-up time From 95% (+VA), with 1-µF storage capacitor Vref range IOUT = 0 Source current Static load Line regulation +VA = 4.75 V to 5.25 V 0.6 mV Drift IOUT = 0 36 PPM/C 4.065 4.096 4.13 V 10 µA DIGITAL INPUT/OUTPUT Logic family - CMOS VIH High-level input voltage IIH = 5 µA +VBD – 1 VIL Low-level input voltage IIL = 5 µA –0.3 +VBD + 0.3 0.8 VOH High-level output voltage IOH = 2 TTL loads +VBD – 0.6 +VBD VOL Low-level output voltage IOL = 2 TTL loads 0 0.4 V Data format - straight binary POWER SUPPLY REQUIREMENTS Power supply voltage +VA Supply current Power dissipation (8) (8) +VBD 2.7 +VA 4.75 3 5.25 V 5 5.25 fs = 1.25 MHz 31 34 mA V fs = 1.25 MHz 155 170 mW 85 °C TEMPERATURE RANGE Operating free-air (8) 4 –40 This includes only VA+ current. +VBD current is typically 1 mA with 5-pF load capacitance on output pins. ADS8405 www.ti.com SLAS427 – DECEMBER 2004 TIMING CHARACTERISTICS All specifications typical at –40°C to 85°C, +VA = +VBD = 5 V (1) (2) (3) PARAMETER MIN tCONV Conversion time 500 tACQ Acquisition time 150 tpd1 CONVST low to BUSY high tpd2 Propagation delay time, end of conversion to BUSY low tw1 Pulse duration, CONVST low tsu1 Setup time, CS low to CONVST low tw2 Pulse duration, CONVST high TYP MAX UNIT 650 ns ns 40 ns 5 ns 20 ns 0 ns 20 ns CONVST falling edge jitter 10 tw3 Pulse duration, BUSY signal low tw4 Pulse duration, BUSY signal high th1 Hold time, first data bus data transition (RD low, or CS low for read cycle, or BYTE input changes) after CONVST low td1 tsu2 tw5 Pulse duration, RD low ten Enable time, RD low (or CS low for read cycle) to data valid td2 Delay time, data hold from RD high 0 td3 Delay time, BYTE rising edge or falling edge to data valid 2 tw6 Pulse duration, RD high 20 ns tw7 Pulse duration, CS high 20 ns th2 Hold time, last RD (or CS for read cycle ) rising edge to CONVST falling edge 50 ns tsu3 Setup time, BYTE transition to RD falling edge 0 ns th3 Hold time, BYTE transition to RD falling edge 0 tdis Disable time, RD high (CS high for read cycle) to 3-stated data bus 20 ns td5 Delay time, end of conversion to MSB data valid 10 ns tsu4 Byte transition setup time, from BYTE transition to next BYTE transition 50 ns td6 Delay time, CS rising edge to BUSY falling edge 50 ns td7 Delay time, BUSY falling edge to CS rising edge 50 ns tsu(AB) Setup time, from the falling edge of CONVST (used to start the valid conversion) to the next falling edge of CONVST (when CS = 0 and CONVST used to abort) or to the next falling edge of CS (when CS is used to abort) 60 tsu5 Setup time, falling edge of CONVST to read valid data (MSB) from current conversion th4 Hold time, data (MSB) from previous conversion hold valid from falling edge of CONVST (1) (2) (3) Min(tACQ) ps ns 610 ns 40 ns Delay time, CS low to RD low (or BUSY low to RD low when CS = 0) 0 ns Setup time, RD high to CS high 0 ns 50 ns 20 ns ns 20 ns ns 500 MAX(tCONV) + MAX(td5) ns ns MIN(tCONV) ns All input signals are specified with tr = tf = 5 ns (10% to 90% of +VBD) and timed from a voltage level of (VIL + VIH)/2. See timing diagrams. All timings are measured with 20-pF equivalent loads on all data bits and BUSY pins. 5 ADS8405 www.ti.com SLAS427 – DECEMBER 2004 TIMING CHARACTERISTICS All specifications typical at –40°C to 85°C, +VA = 5 V, +VBD = 3 V (1) (2) (3) PARAMETER MIN TYP MAX UNIT 650 ns tCONV Conversion time 500 tACQ Acquisition time 150 tpd1 CONVST low to BUSY high 50 ns tpd2 Propagation delay time, end of conversion to BUSY low 10 ns tw1 Pulse duration, CONVST low tsu1 Setup time, CS low to CONVST low tw2 Pulse duration, CONVST high ns 20 ns 0 ns 20 ns CONVST falling edge jitter 10 tw3 Pulse duration, BUSY signal low tw4 Pulse duration, BUSY signal high th1 Hold time, first data bus transition (RD low, or CS low for read cycle, or BYTE input changes) after CONVST low 40 ns td1 Delay time, CS low to RD low (or BUSY low to RD low when CS = 0) 0 ns tsu2 Setup time, RD high to CS high 0 ns tw5 Pulse duration, RD low 50 ns ten Enable time, RD low (or CS low for read cycle) to data valid td2 Delay time, data hold from RD high 0 td3 Delay time, BYTE rising edge or falling edge to data valid 2 tw6 Pulse duration, RD high 20 ns tw7 Pulse duration, CS high 20 ns th2 Hold time, last RD (or CS for read cycle ) rising edge to CONVST falling edge 50 ns tsu3 Setup time, BYTE transition to RD falling edge 0 ns th3 Hold time, BYTE transition to RD falling edge 0 tdis Disable time, RD high (CS high for read cycle) to 3-stated data bus 30 ns td5 Delay time, end of conversion to MSB data valid 20 ns tsu4 Byte transition setup time, from BYTE transition to next BYTE transition 50 ns td6 Delay time, CS rising edge to BUSY falling edge 50 ns td7 Delay time, BUSY falling edge to CS rising edge 50 ns tsu(AB) Setup time, from the falling edge of CONVST (used to start the valid conversion) to the next falling edge of CONVST (when CS = 0 and CONVST used to abort) or to the next falling edge of CS (when CS is used to abort) 70 tsu5 Setup time, falling edge of CONVST to read valid data (MSB) from current conversion th4 Hold time, data (MSB) from previous conversion hold valid from falling edge of CONVST (1) (2) (3) 6 Min(tACQ) ps ns 610 ns 30 ns ns 30 ns ns 500 MAX(tCONV) + MAX(td5) ns ns MIN(tCONV) All input signals are specified with tr = tf = 5 ns (10% to 90% of +VBD) and timed from a voltage level of (VIL + VIH)/2. See timing diagrams. All timings are measured with 10-pF equivalent loads on all data bits and BUSY pins. ns ADS8405 www.ti.com SLAS427 – DECEMBER 2004 PIN ASSIGNMENTS BUSY BDGND +VBD DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 BDGND PFB PACKAGE (TOP VIEW) 36 35 34 33 32 31 30 29 28 27 26 25 37 24 38 23 39 22 40 21 41 20 42 19 43 18 44 17 45 16 46 15 47 14 48 3 4 5 6 7 8 13 9 10 11 12 REFIN REFOUT NC +VA AGND +IN -IN AGND +VA +VA 1 2 +VBD DB8 DB9 DB10 DB11 DB12 DB13 DB14 DB15 AGND AGND +VA AGND AGND +VBD RESET BYTE CONVST RD CS +VA AGND AGND +VA REFM REFM NC - No connection 7 ADS8405 www.ti.com SLAS427 – DECEMBER 2004 Terminal Functions NAME AGND BDGND NO. I/O DESCRIPTION 5, 8, 11, 12, 14, 15, 44, 45 – Analog ground 25, 35 – Digital ground for bus interface digital supply BUSY 36 O Status output. High when a conversion is in progress. BYTE 39 I Byte select input. Used for 8-bit bus reading. 0: No fold back 1: Low byte D[7:0] of the 16 most significant bits is folded back to high byte of the 16 most significant pins DB[15:8]. CONVST 40 I Convert start. The falling edge of this input ends the acquisition period and starts the hold period. CS 42 I Chip select. The falling edge of this input starts the acquisition period. 8-Bit Bus Data Bus 16-Bit Bus BYTE = 0 BYTE = 1 BYTE = 0 DB15 16 O D15 (MSB) D7 D15 (MSB) DB14 17 O D14 D6 D14 DB13 18 O D13 D5 D13 DB12 19 O D12 D4 D12 DB11 20 O D11 D3 D11 DB10 21 O D10 D2 D10 DB9 22 O D9 D1 D9 DB8 23 O D8 D0 (LSB) D8 DB7 26 O D7 All ones D7 DB6 27 O D6 All ones D6 DB5 28 O D5 All ones D5 DB4 29 O D4 All ones D4 DB3 30 O D3 All ones D3 DB2 31 O D2 All ones D2 DB1 32 O D1 All ones D1 DB0 33 O D0 (LSB) All ones D0 (LSB) –IN 7 I Inverting input channel +IN 6 I Noninverting input channel NC 3 – No connection REFIN 1 I Reference input REFM 47, 48 I Reference ground REFOUT 2 O Reference output. Add 1-µF capacitor between the REFOUT pin and REFM pin when the internal reference is used. RESET 38 I Current conversion is aborted and output latches are cleared (set to zeros) when this pin is asserted low. RESET works independantly of CS. RD 41 I Synchronization pulse for the parallel output. When CS is low, this serves as the output enable and puts the previous conversion result on the bus. +VA 4, 9, 10, 13, 43, 46 – Analog power supplies, 5-V dc 24, 34, 37 – Digital power supply for bus +VBD 8 ADS8405 www.ti.com SLAS427 – DECEMBER 2004 TIMING DIAGRAMS tw2 tw1 CONVST (used in normal conversion) tcycle CONVST (used in ABORT) tsu(AB) tpd1 tsu(AB) tpd2 tw4 tpd1 tw3 BUSY tsu1 tw7 td7 CS td6 CONVERT† tCONV tCONV SAMPLING† (When CS Toggle) tACQ BYTE tsu4 th1 tsu2 td1 th2 RD Data to be read† Invalid Previous Conversion th4 tdis ten tsu5 DB[15:8] Invalid Current Conversion Hi−Z Hi−Z D [15:8] DB[7:0] Hi−Z D [7:0] Hi−Z D [7:0] †Signal internal to device Figure 1. Timing for Conversion and Acquisition Cycles With CS and RD Toggling 9 ADS8405 www.ti.com SLAS427 – DECEMBER 2004 TIMING DIAGRAMS (continued) tw1 CONVST (used in normal conversion) tw2 tcycle CONVST (used in ABORT) tsu(AB) tpd1 tsu(AB) tpd2 tw4 tw3 BUSY tw7 tsu1 td7 CS td6 CONVERT† tCONV tCONV SAMPLING† (When CS Toggle) tACQ BYTE th1 RD = 0 Data to be read† tdis ten DB[15:8] DB[7:0] †Signal Invalid Current Conversion tsu5 Hi−Z Previous D [15:8] Hi−Z Hi−Z Previous D [7:0] Hi−Z internal to device tdis Invalid Previous Conversion th4 tsu4 th2 ten D [15:8] D [7:0] D [7:0] Hi−Z Repeated D [15:8] Hi−Z Repeated D [7:0] ten Figure 2. Timing for Conversion and Acquisition Cycles With CS Toggling, RD Tied to BDGND 10 ADS8405 www.ti.com SLAS427 – DECEMBER 2004 TIMING DIAGRAMS (continued) tw1 tw2 CONVST (used in normal conversion) tcycle CONVST (used in ABORT) tsu(AB) tpd1 tsu(AB) tpd2 tw4 tpd1 tw3 BUSY CS = 0 CONVERT† tCONV tCONV t(ACQ) SAMPLING† (When CS = 0) BYTE tsu4 th1 th2 RD tdis ten Data to be read† th4 DB[15:8] DB[7:0] †Signal Invalid Invalid Previous Conversion Current Conversion tsu5 Hi−Z Hi−Z D [15:8] D [7:0] D [7:0] Hi−Z Hi−Z internal to device Figure 3. Timing for Conversion and Acquisition Cycles With CS Tied to BDGND, RD Toggling 11 ADS8405 www.ti.com SLAS427 – DECEMBER 2004 TIMING DIAGRAMS (continued) tw1 CONVST (used in normal conversion) tw2 tcycle CONVST (used in ABORT) tsu(AB) tpd1 tsu(AB) tpd2 tw4 tpd1 tpd2 tw3 BUSY CS = 0 CONVERT† tCONV tCONV tACQ SAMPLING† (When CS Toggle) th1 th1 BYTE RD = 0 td3 td3 td5 th4 tsu5 Previous MSB Invalid DB[15:8] Previous Previous LSB LSB Invalid DB[7:0] †Signal td5 th4 td3 tsu5 Invalid MSB LSB MSB MSB LSB MSB Invalid internal to device Figure 4. Timing for Conversion and Acquisition Cycles With CS and RD Tied to BDGND—Auto Read CS RD tsu4 BYTE ten tdis tdis ten DB[15:0] td3 Hi−Z Valid Hi−Z Valid Valid Figure 5. Detailed Timing for Read Cycles 12 Hi−Z ADS8405 www.ti.com SLAS427 – DECEMBER 2004 TYPICAL CHARACTERISTICS At –40°C to 85°C, +VA = 5 V, +VBD = 5 V, REFIN = 4.096 V (internal reference used) and fsample = 1.25 MHz (unless otherwise noted) SIGNAL-TO-NOISE RATIO vs FREE-AIR TEMPERATURE HISTOGRAM (DC Code Spread) HALF SCALE 131071 CONVERSIONS 86.8 80000 70000 60000 SNR − Signal-to-Noise Ratio − dB +VA = 5 V, +VBD = 3.3 V, TA = 25°C, Code = 65292 50000 40000 30000 20000 10000 86.4 86.2 86 85.8 85.6 85.4 fi = 50 kHz, Full Scale Input, +VA = 5 V, +VBD = 3 V, Int Ref = 4.096 V 65295 65292 65289 85.2 −40 −25 −10 5 20 35 50 65 80 TA − Free-Air Temperature − C Figure 6. Figure 7. SIGNAL-TO-NOISE AND DISTORTION vs FREE-AIR TEMPERATURE EFFECTIVE NUMBER OF BITS vs FREE-AIR TEMPERATURE 83.6 13.6 ENOB − Effective Number of Bits − Bits SINAD − Signal-to-Noise and Distortion − dB 0 86.6 83.4 83.2 83 82.8 82.6 82.4 82.2 82 fi = 50 kHz, Full Scale Input, +VA = 5 V, +VBD = 3 V, Int Ref = 4.096 V 81.8 −40 −25 −10 5 20 35 50 65 TA − Free-Air Temperature − C Figure 8. 13.55 13.5 13.45 13.4 13.35 13.3 fi = 50 kHz, Full Scale Input, +VA = 5 V, +VBD = 3 V, Int Ref = 4.096 V 13.25 80 −40 −25 −10 5 20 35 50 65 80 TA − Free-Air Temperature − C Figure 9. 13 ADS8405 www.ti.com SLAS427 – DECEMBER 2004 TYPICAL CHARACTERISTICS (continued) TOTAL HARMONIC DISTORTION vs FREE-AIR TEMPERATURE 95 −90 THD − Total Harmonic Distortion − dB SFDR − Spurious Free Dynamic Range − dB SPURIOUS FREE DYNAMIC RANGE vs FREE-AIR TEMPERATURE 94 93 92 91 fi = 50 kHz, Full Scale Input, +VA = 5 V, +VBD = 3 V, Int Ref = 4.096 V 90 −40 −25 −10 5 20 35 50 65 −94 EFFECTIVE NUMBER OF BITS vs INPUT FREQUENCY 86.7 86.6 86.5 86.4 86.3 fi = 50 kHz, Full Scale Input, +VA = 5 V, +VBD = 3 V, Int Ref = 4.096 V 86 13.9 13.85 13.8 13.75 13.7 13.65 13.6 13.55 13.45 13.4 10 20 30 40 50 60 70 80 90 100 fi = 50 kHz, Full Scale Input, +VA = 5 V, +VBD = 3 V, Int Ref = 4.096 V 13.5 0 50 60 70 80 90 100 Figure 12. Figure 13. SIGNAL-TO-NOISE AND DISTORTION vs INPUT FREQUENCY SPURIOUS FREE DYNAMIC RANGE vs INPUT FREQUENCY 85.5 85 84.5 84 83.5 fi = 50 kHz, Full Scale Input, +VA = 5 V, +VBD = 3 V, Int Ref = 4.096 V 83 82.5 0 10 20 30 40 50 60 70 80 90 100 fi − Input Frequency − kHz Figure 14. SFDR − Spurious Free Dynamic Range − dB SINAD − Signal-to-Noise and Distortion − dB 10 20 30 40 fi − Input Frequency − kHz fi − Input Frequency − kHz 14 80 SIGNAL-TO-NOISE RATIO vs INPUT FREQUENCY ENOB − Effective Number of Bits − Bits SNR − Signal-to-Noise Ratio − dB −93 Figure 11. 86.8 0 −92 Figure 10. 86.9 86.1 fi = 50 kHz, Full Scale Input, +VA = 5 V, +VBD = 3 V, Int Ref = 4.096 V −95 −40 −25 −10 5 20 35 50 65 TA − Free-Air Temperature − C 80 TA − Free-Air Temperature − C 86.2 −91 101 100 99 98 97 96 95 94 fi = 50 kHz, Full Scale Input, +VA = 5 V, +VBD = 3 V, Int Ref = 4.096 V 93 92 91 0 10 20 30 40 50 60 70 80 90 100 fi − Input Frequency − kHz Figure 15. ADS8405 www.ti.com SLAS427 – DECEMBER 2004 TYPICAL CHARACTERISTICS (continued) TOTAL HARMONIC DISTORTION vs INPUT FREQUENCY 29 fi = 50 kHz, Full Scale Input, +VA = 5 V, +VBD = 3 V, Int Ref = 4.096 V −92 −93 −94 −95 −96 −97 −98 −99 0 27.5 27 26.5 26 25 250 10 20 30 40 50 60 70 80 90 100 fi − Input Frequency − kHz 750 1000 Figure 16. Figure 17. GAIN ERROR vs SUPPLY VOLTAGE OFFSET ERROR vs SUPPLY VOLTAGE +VBD = 3.3 V, TA = 25°C, Ext Ref = 4.096 V Offset Voltage − mV 0.25 0.05 0 −0.05 0.2 0.15 0.1 0.05 −0.1 −0.15 4.75 5 0 4.75 5.25 VCC − Supply Voltage − V 5 VCC − Supply Voltage − V Figure 18. Figure 19. INTERNAL VOLTAGE REFERENCE vs FREE-AIR TEMPERATURE GAIN ERROR vs FREE-AIR TEMPERATURE 4.093 0.5 4.092 0.4 4.091 0.3 Gain Error − mV 4.090 4.089 4.088 4.087 4.086 5.25 +VA = 5 V, +VBD = 3.3 V, Ext Ref = 4.096 V 0.2 0.1 0 −0.1 −0.2 4.085 +VA = 5 V +VBD = 3.3 V 4.084 −0.3 −0.4 4.083 4.082 1250 0.3 +VBD = 3.3 V, TA = 25°C, Ext Ref = 4.096 V 0.1 Internal Reference Output Voltage − V 500 Sample Rate − KSPS 0.15 Gain Error − mV 28 25.5 −100 −101 +VA = 5 V, +VBD = 3.3 V, TA = 25°C, Int Ref = 4.096 V 28.5 I CC − Supply Current − mA THD − Total Harmonic Distortion − dB −91 SUPPLY CURRENT vs SAMPLE RATE −40 −25 −10 5 20 35 50 65 TA − Free-Air Temperature − C Figure 20. 80 −0.5 −40 −25 −10 5 20 35 50 65 TA − Free-Air Temperature − C 80 Figure 21. 15 ADS8405 www.ti.com SLAS427 – DECEMBER 2004 TYPICAL CHARACTERISTICS (continued) OFFSET ERROR vs FREE-AIR TEMPERATURE SUPPLY CURRENT vs FREE-AIR TEMPERATURE 29.2 0.5 +VA = 5 V, +VBD = 3.3 V, Ext Ref = 4.096 V Offset Voltage − mV 0.4 0.35 0.3 0.25 0.2 0.15 0.1 28.8 28.6 28.4 28.2 28 0.05 0 −40 −25 −10 5 20 35 50 65 27.8 80 −40 −25 −10 35 50 65 Figure 22. Figure 23. DIFFERENTIAL NONLINEARITY vs FREE-AIR TEMPERATURE INTEGRAL NONLINEARITY vs FREE-AIR TEMPERATURE 80 1.5 Max INL − Integral Nonlinearity − Bits 0.6 0.4 0.2 +VA = 5 V, +VBD = 3.3 V, Ext Ref = 4.096 V 0 −0.2 Min −0.4 −0.6 20 35 50 65 Max 1 0.5 +VA = 5 V, +VBD = 3.3 V, Ext Ref = 4.096 V 0 −0.5 Min −1 −1.5 −40 −25 −10 80 TA − Free-Air Temperature − C 5 20 35 50 65 80 TA − Free-Air Temperature − C Figure 24. Figure 25. DIFFERENTIAL NONLINEARITY vs REFERENCE VOLTAGE INTEGRAL NONLINEARITY vs REFERENCE VOLTAGE 2 2 1.5 INL − Integral Nonlinearity − Bits DNL − Differential Nonlinearity − Bits 20 TA − Free-Air Temperature − C −0.8 −40 −25 −10 5 Max 1 0.5 +VA = 5 V, +VBD = 3.3 V, Ext Ref = Varied 0 −0.5 Min −1 −1.5 1.5 Max 1 0.5 0 +VA = 5 V, +VBD = 3.3 V, Ext Ref = Varied −0.5 −1 Min −1.5 −2 2.5 3 3.5 VREF − Reference Voltage − V Figure 26. 16 5 TA − Free-Air Temperature − C 0.8 DNL − Differential Nonlinearity − Bits +VA = 5 V, +VBD = 3.3 V 29 I CC − Supply Current − mA 0.45 4 −2 2.5 3 3.5 VREF − Reference Voltage − V Figure 27. 4 ADS8405 www.ti.com SLAS427 – DECEMBER 2004 TYPICAL CHARACTERISTICS (continued) DNL 2.5 +VA = 5 V, +VBD = 5 V, TA = 25°C, Ext Ref = 4.096 V 2 1.5 DNL − LSBs 1 0.5 0 −0.5 −1 −1.5 −2 −2.5 0 16384 32768 Code 49152 65536 Figure 28. INL 2.5 +VA = 5 V, +VBD = 5 V, TA = 25°C, Ext Ref = 4.096 V 2 1.5 INL − LSBs 1 0.5 0 −0.5 −1 −1.5 −2 −2.5 0 16384 32768 Code 49152 65536 Figure 29. FFT 0 +VA = 5 V, +VBD = 3.3 V, REF +32768 Points, fi = 100 kHz, fs = 1.25 MHz, TA = 25°C, Int Ref = 4.096 V Amplitude −50 −100 −150 −200 0 200 400 Frequency − kHz 600 Figure 30. 17 ADS8405 www.ti.com SLAS427 – DECEMBER 2004 APPLICATION INFORMATION MICROCONTROLLER INTERFACING ADS8405 to 8-Bit Microcontroller Interface Figure 31 shows a parallel interface between the ADS8405 and a typical microcontroller using the 8-bit data bus. The BUSY signal is used as a falling-edge interrupt to the microcontroller. Analog 5 V 0.1 µF AGND 10 µF Ext Ref Input 0.1 µF 1 µF Micro Controller −IN REFM AGND +IN +VA REFIN Analog Input Digital 3 V GPIO CS BYTE GPIO P[7:0] ADS8405 DB[15:8] RD CONVST BUSY RD GPIO INT 0.1 µF BDGND BDGND +VBD Figure 31. ADS8405 Application Circuitry (Using an External Reference) Analog 5 V 0.1 µF AGND 10 µF 0.1 µF AGND AGND REFM REFIN REFOUT +VA 1 µF ADS8405 Figure 32. Using the Internal Reference PRINCIPLES OF OPERATION The ADS8405 is a high-speed successive approximation register (SAR) analog-to-digital converter (ADC). The architecture is based on charge redistribution, which inherently includes a sample/hold function. See Figure 31 for the application circuit for the ADS8405. The conversion clock is generated internally. The conversion time of 650 ns is capable of sustaining a 1.25-MHz throughput. 18 ADS8405 www.ti.com SLAS427 – DECEMBER 2004 PRINCIPLES OF OPERATION (continued) The analog input is provided to two input pins: +IN and –IN. When a conversion is initiated, the differential input on these pins is sampled on the internal capacitor array. While a conversion is in progress, both inputs are disconnected from any internal function. REFERENCE The ADS8405 can operate with an external reference with a range from 2.5 V to 4.2 V. A 4.096-V internal reference is included. When an internal reference is used, pin 2 (REFOUT) should be connected to pin 1 (REFIN) with a 0.1-µF decoupling capacitor and a 1-µF storage capacitor between pin 2 (REFOUT) and pins 47 and 48 (REFM) (see Figure 32). The internal reference of the converter is double buffered. If an external reference is used, the second buffer provides isolation between the external reference and the CDAC. This buffer is also used to recharge all of the capacitors of the CDAC during conversion. Pin 2 (REFOUT) can be left unconnected (floating) if an external reference is used. ANALOG INPUT When the converter enters hold mode, the voltage difference between the +IN and -IN inputs is captured on the internal capacitor array. The voltage on the –IN input is limited between –0.2 V and 0.2 V, allowing the input to reject small signals which are common to both the +IN and –IN inputs. The +IN input has a range of –0.2 V to Vref + 0.2 V. The input span (+IN – (–IN)) is limited to 0 V to Vref. The input current on the analog inputs depends upon a number of factors: sample rate, input voltage, and source impedance. Essentially, the current into the ADS8405 charges the internal capacitor array during the sample period. After this capacitance has been fully charged, there is no further input current. The source of the analog input voltage must be able to charge the input capacitance (25 pF) to an 16-bit settling level within the acquisition time (150 ns) of the device. When the converter goes into hold mode, the input impedance is greater than 1 GΩ. Care must be taken regarding the absolute analog input voltage. To maintain the linearity of the converter, the +IN and –IN inputs and the span (+IN – (–IN)) should be within the limits specified. Outside of these ranges, the converter's linearity may not meet specifications. To minimize noise, low bandwidth input signals with low-pass filters should be used. Care should be taken to ensure that the output impedance of the sources driving the +IN and –IN inputs are matched. If this is not observed, the two inputs could have different setting times. This may result in offset error, gain error, and linearity error which varies with temperature and input voltage. A typical input circuit using TI's THS4031 is shown in Figure 33. 300 15 V 0.1 F 1 F 300 G = +2 _ 15 THS4031 VIN + +IN ADS8405 1 F 6800 pF −IN 0.1 F −15 V Figure 33. Using the THS4031 with the ADS8405 19 ADS8405 www.ti.com SLAS427 – DECEMBER 2004 PRINCIPLES OF OPERATION (continued) DIGITAL INTERFACE Timing And Control See the timing diagrams in the specifications section for detailed information on timing signals and their requirements. The ADS8405 uses an internal oscillator generated clock which controls the conversion rate and in turn the throughput of the converter. No external clock input is required. Conversions are initiated by bringing the CONVST pin low for a minimum of 20 ns (after the 20 ns minimum requirement has been met, the CONVST pin can be brought high) while CS is low. The ADS8405 switches from the sample to the hold mode on the falling edge of the CONVST command. A clean and low jitter falling edge of this signal is important to the performance of the converter. The BUSY output is brought high after CONVST goes low. BUSY stays high throughout the conversion process and returns low when the conversion has ended. Sampling starts as soon as the conversion is over when CS is tied low or starts with the falling edge of CS when BUSY is low. Both RD and CS can be high during and before a conversion with one exception (CS must be low when CONVST goes low to initiate a conversion). Both the RD and CS pins are brought low in order to enable the parallel output bus with the conversion. Reading Data The ADS8405 outputs full parallel data in straight binary format as shown in Table 1. The parallel output is active when CS and RD are both low. There is a minimal quiet zone requirement around the falling edge of CONVST. This is 50 ns prior to the falling edge of CONVST and 40 ns after the falling edge. No data read should be attempted within this zone. Any other combination of CS and RD sets the parallel output to 3-state. BYTE is used for multiword read operations. BYTE is used whenever lower bits of the converter result are output on the higher byte of the bus. Refer to Table 1 for ideal output codes. Table 1. Ideal Input Voltages and Output Codes DESCRIPTION ANALOG VALUE DIGITAL OUTPUT Full scale range +Vref Least significant bit (LSB) (+Vref)/65536 STRAIGHT BINARY Full scale (+Vref) – 1 LSB 1111 1111 1111 1111 FFFF Midscale (+Vref)/2 1000 0000 0000 0000 8000 Midscale – 1 LSB (+Vref)/2 – 1 LSB 0111 1111 1111 1111 7FFF Zero 0V 0000 0000 0000 0000 0000 BINARY CODE HEX CODE The output data is a full 16-bit word (D15 – D0) on the DB15 – DB0 pins (MSB-LSB) if BYTE is low. The result may also be read on an 8-bit bus for convenience. This is done by using only pins DB15 – DB8. In this case two reads are necessary: the first as before, leaving BYTE low and reading the 8 most significant bits on pins DB15 – DB8, then bringing BYTE high. When BYTE is high, the low bits (D7 – D0) appear on pins DB15 – D8. These multiword read operations can be done with multiple active RD (toggling) or with RD tied low for simplicity. Conversion Data Readout BYTE 20 DATA READ OUT DB15–DB8 Pins DB7–DB0 Pins High D7–D0 All one's Low D15–D8 D7-D0 ADS8405 www.ti.com SLAS427 – DECEMBER 2004 RESET RESET is an asynchronous active low input signal (that works independently of CS). Minimum RESET low time is 25 ns. The current conversion is aborted no later than 50 ns after the converter is in reset mode. In addition, all output latches are cleared (set to zero's) after RESET. The converter goes back to normal operation mode no later than 20 ns after the RESET input is brought high. The converter starts the first sampling period 20 ns after the rising edge of RESET. Any sampling period except for the one immediately after a RESET is started with the falling edge of the previous BUSY signal or the falling edge of CS, whichever is later. Another way to reset the device is through the use of the combination of CS and CONVST. This is useful when the dedicated RESET pin is tied to the system reset but there is a need to abort only the conversion in a specific converter. Since the BUSY signal is held high during the conversion, either one of these conditions triggers an internal self-clear reset to the converter just the same as a reset via the dedicated RESET pin. The reset does not have to be cleared as for the dedicated RESET pin. A reset can be started with either of the two following steps. • Issue a CONVST when CS is low and a conversion is in progress. The falling edge of CONVST must satisfy the timing as specified by the timing parameter tsu(AB) specified in the timing characteristics table to ensure a reset. The falling edge of CONVST starts a reset. The timing is the same as a reset using the dedicated RESET pin except the instance of the falling edge is replaced by the falling edge of CONVST. • Issue a CS while a conversion is in progress. The falling edge of CS must satisfy the timing as specified by the timing parameter tsu(AB) specified in the timing characteristics table to ensure a reset. The falling edge of CS causes a reset. The timing is the same as a reset using the dedicated RESET pin except the instance of the falling edge is replaced by the falling edge of CS. POWER-ON INITIALIZATION RESET is not required after power on. An internal power-on reset circuit generates the reset. To ensure that all of the registers are cleared, the three conversion cycles must be given to the converter after power on. LAYOUT For optimum performance, care should be taken with the physical layout of the ADS8405 circuitry. As the ADS8405 offers single-supply operation, it is often used in close proximity with digital logic, microcontrollers, microprocessors, and digital signal processors. The more digital logic present in the design and the higher the switching speed, the more difficult it is to achieve good performance from the converter. The basic SAR architecture is sensitive to glitches or sudden changes on the power supply, reference, ground connections, and digital inputs that occur just prior to latching the output of the analog comparator. Thus, driving any single conversion for an n-bit SAR converter, there are at least n windows in which large external transient voltages can affect the conversion result. Such glitches might originate from switching power supplies, nearby digital logic, or high power devices. The degree of error in the digital output depends on the reference voltage, layout, and the exact timing of the external event. On average, the ADS8405 draws very little current from an external reference, as the reference voltage is internally buffered. If the reference voltage is external and originates from an op amp, make sure that it can drive the bypass capacitor or capacitors without oscillation. A 0.1-µF bypass capacitor and a 1-µF storage capacitor are recommended from pin 1 (REFIN) directly to pin 48 (REFM). REFM and AGND should be shorted on the same ground plane under the device. The AGND and BDGND pins should be connected to a clean ground point. In all cases, this should be the analog ground. Avoid connections which are close to the grounding point of a microcontroller or digital signal processor. If required, run a ground trace directly from the converter to the power supply entry point. The ideal layout consists of an analog ground plane dedicated to the converter and associated analog circuitry. 21 ADS8405 www.ti.com SLAS427 – DECEMBER 2004 As with the AGND connections, +VA should be connected to a 5-V power supply plane or trace that is separate from the connection for digital logic until they are connected at the power entry point. Power to the ADS8405 should be clean and well bypassed. A 0.1-µF ceramic bypass capacitor should be placed as close to the device as possible. See Table 2 for the placement of the capacitor. In addition, a 1-µF to 10-µF capacitor is recommended. In some situations, additional bypassing may be required, such as a 100-µF electrolytic capacitor or even a Pi filter made up of inductors and capacitors—all designed to essentially low-pass filter the 5-V supply, removing the high frequency noise. Table 2. Power Supply Decoupling Capacitor Placement POWER SUPPLY PLANE SUPPLY PINS CONVERTER ANALOG SIDE CONVERTER DIGITAL SIDE Pin pairs that require shortest path to decoupling capacitors (4,5), (8,9), (10,11), (13,15), (43,44), (45,46) (24,25), (34, 35) Pins that require no decoupling 12, 14 37 22 PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) ADS8405IBPFBR ACTIVE TQFP PFB 48 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 ADS8405I B ADS8405IBPFBRG4 ACTIVE TQFP PFB 48 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 ADS8405I B ADS8405IBPFBT ACTIVE TQFP PFB 48 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 ADS8405I B ADS8405IBPFBTG4 ACTIVE TQFP PFB 48 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 ADS8405I B ADS8405IPFBR ACTIVE TQFP PFB 48 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 ADS8405I ADS8405IPFBRG4 ACTIVE TQFP PFB 48 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 ADS8405I ADS8405IPFBT ACTIVE TQFP PFB 48 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 ADS8405I ADS8405IPFBTG4 ACTIVE TQFP PFB 48 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 ADS8405I (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 26-Jan-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing ADS8405IBPFBR TQFP PFB 48 ADS8405IBPFBT TQFP PFB ADS8405IPFBR TQFP PFB ADS8405IPFBT TQFP PFB SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 1000 330.0 16.4 9.6 9.6 1.5 12.0 16.0 Q2 48 250 330.0 16.4 9.6 9.6 1.5 12.0 16.0 Q2 48 1000 330.0 16.4 9.6 9.6 1.5 12.0 16.0 Q2 48 250 330.0 16.4 9.6 9.6 1.5 12.0 16.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 26-Jan-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) ADS8405IBPFBR TQFP PFB 48 1000 367.0 367.0 38.0 ADS8405IBPFBT TQFP PFB 48 250 367.0 367.0 38.0 ADS8405IPFBR TQFP PFB 48 1000 367.0 367.0 38.0 ADS8405IPFBT TQFP PFB 48 250 367.0 367.0 38.0 Pack Materials-Page 2 MECHANICAL DATA MTQF019A – JANUARY 1995 – REVISED JANUARY 1998 PFB (S-PQFP-G48) PLASTIC QUAD FLATPACK 0,27 0,17 0,50 36 0,08 M 25 37 24 48 13 0,13 NOM 1 12 5,50 TYP 7,20 SQ 6,80 9,20 SQ 8,80 Gage Plane 0,25 0,05 MIN 0°– 7° 1,05 0,95 Seating Plane 0,75 0,45 0,08 1,20 MAX 4073176 / B 10/96 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Falls within JEDEC MS-026 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated