TI SN74AHCT595PW

SCLS374L − MAY 1997 − REVISED FEBRUARY 2004
QB
QC
QD
QE
QF
QG
QH
GND
description/ordering information
The ’AHCT595 devices contain an 8-bit serial-in,
parallel-out shift register that feeds an 8-bit D-type
storage register. The storage register has parallel
3-state outputs. Separate clocks are provided for
the shift and storage registers. The shift register
has a direct overriding clear (SRCLR) input, serial
(SER) input, and serial outputs for cascading.
When the output-enable (OE) input is high, the
outputs are in the high-impedance state.
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
VCC
QA
SER
OE
RCLK
SRCLK
SRCLR
QH′
QC
QB
SN54AHCT595 . . . FK PACKAGE
(TOP VIEW)
3 2 1 20 19
18
5
17
6
16
7
15
8
14
9 10 11 12 13
QH
Both the shift register clock (SRCLK) and storage
register clock (RCLK) are positive-edge triggered.
If both clocks are connected together, the shift
register always is one clock pulse ahead of the
storage register.
4
SER
OE
NC
RCLK
SRCLK
SRCLR
QD
QE
NC
QF
QG
NC
VCC
QA
D
SN54AHCT595 . . . J OR W PACKAGE
SN74AHCT595 . . . D, DB, N, NS, OR PW PACKAGE
(TOP VIEW)
Inputs Are TTL-Voltage Compatible
8-Bit Serial-In, Parallel-Out Shift
Shift Register Has Direct Clear
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
ESD Protection Exceeds JESD 22
− 2000-V Human-Body Model (A114-A)
− 200-V Machine Model (A115-A)
− 1000-V Charged-Device Model (C101)
GND
NC
Q H′
D
D
D
D
NC − No internal connection
ORDERING INFORMATION
PDIP − N
SN74AHCT595N
Tube
SN74AHCT595D
Tape and reel
SN74AHCT595DR
SOP − NS
Tape and reel
SN74AHCT595NSR
AHCT595
SSOP − DB
Tape and reel
SN74AHCT595DBR
HB595
Tube
SN74AHCT595PW
Tape and reel
SN74AHCT595PWR
CDIP − J
Tube
SNJ54AHCT595J
SNJ54AHCT595J
CFP − W
Tube
SNJ54AHCT595W
SNJ54AHCT595W
LCCC − FK
Tube
SNJ54AHCT595FK
SNJ54AHCT595FK
TSSOP − PW
−55°C
−55
C to 125
125°C
C
TOP-SIDE
MARKING
Tube
SOIC − D
−40°C
85°C
−40
C to 85
C
ORDERABLE
PART NUMBER
PACKAGE†
TA
SN74AHCT595N
AHCT595
HB595
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines
are available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2004, Texas Instruments Incorporated
!"#$%& "!&'& &(!)$'!& "#))%& ' !( *#+,"'!& '%- )!#" "!&(!)$ !
*%"("'!& *%) % %)$ !( %.' &)#$%& '&') /'))'&0)!#"!& *)!"%&1 !% &! &%"%'),0 &",#% %&1 !( ',,
*')'$%%)POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SCLS374L − MAY 1997 − REVISED FEBRUARY 2004
FUNCTION TABLE
INPUTS
2
SER
SRCLK
X
X
X
X
X
X
L
SRCLR
FUNCTION
RCLK
OE
X
X
H
X
X
L
Outputs QA−QH are disabled.
Outputs QA−QH are enabled.
L
X
X
Shift register is cleared.
↑
H
X
X
First stage of the shift register goes low.
Other stages store the data of previous stage, respectively.
H
↑
H
X
X
First stage of the shift register goes high.
Other stages store the data of previous stage, respectively.
X
X
X
↑
X
Shift-register data is stored in the storage register.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCLS374L − MAY 1997 − REVISED FEBRUARY 2004
logic diagram (positive logic)
OE
RCLK
SRCLR
SRCLK
SER
13
12
10
11
14
1D Q
C1
R
3D
C3 Q
15
2D Q
C2
R
3D
C3 Q
1
2D Q
C2
R
3D
C3 Q
2
2D Q
C2
R
3D
C3 Q
3
2D Q
C2
R
3D
C3 Q
4
2D Q
C2
R
3D
C3 Q
5
2D Q
C2
R
3D
C3 Q
6
2D Q
C2
R
3D
C3 Q
7
9
QA
QB
QC
QD
QE
QF
QG
QH
QH′
Pin numbers shown are for the D, DB, J, N, NS, PW, and W packages.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SCLS374L − MAY 1997 − REVISED FEBRUARY 2004
timing diagram
SRCLK
SER
RCLK
SRCLR
OE
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
QA
QB
QC
QD
QE
QF
QG
QH
QH’
NOTE:
4
ÎÎÎÎ
implies that the output is in 3-State mode.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCLS374L − MAY 1997 − REVISED FEBRUARY 2004
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Output voltage range, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCC + 0.5 V
Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −20 mA
Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25 mA
Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA
Package thermal impedance, θJA (see Note 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73°C/W
DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82°C/W
N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67°C/W
NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64°C/W
PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
2. The package thermal impedance is calculated in accordance with JESD 51-7.
recommended operating conditions (see Note 3)
SN54AHCT595
MIN
MAX
MIN
MAX
4.5
5.5
4.5
5.5
VCC
VIH
Supply voltage
VIL
VI
Low-level input voltage
Input voltage
0
5.5
VO
IOH
Output voltage
0
High-level output current
VCC
−8
IOL
∆t/∆v
Low-level output current
High-level input voltage
SN74AHCT595
2
2
0.8
Input transition rise or fall rate
UNIT
V
V
0.8
V
0
5.5
V
0
VCC
−8
mA
8
8
mA
20
20
ns/V
V
TA
Operating free-air temperature
−55
125
−40
85
°C
NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
2 &(!)$'!& "!&"%)& *)!#" & % (!)$'3% !)
%1& *'% !( %3%,!*$%&- ')'"%)" '' '& !%)
*%"("'!& ')% %1& 1!',- %.' &)#$%& )%%)3% % )1 !
"'&1% !) "!&&#% %% *)!#" /!# &!"%-
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SCLS374L − MAY 1997 − REVISED FEBRUARY 2004
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
VOH
IOH = −50 mA
IOH = −8 mA
4.5 V
VOL
IOL = 50 mA
IOL = 8 mA
4.5 V
II
IOZ
VI = 5.5 V or GND
VO = VCC or GND,
ICC
∆ICC†
Ci
MIN
4.4
QA−QH
VI = VCC or GND,
IO = 0
One input at 3.4V,
Other inputs at VCC or GND
TA = 25°C
TYP
MAX
4.5
3.94
SN54AHCT595
MIN
MAX
SN74AHCT595
MIN
4.4
4.4
3.8
3.8
MAX
UNIT
V
0.1
0.1
0.1
0.36
0.44
0.44
0 V to 5.5 V
±0.1
±1*
±1
mA
5.5 V
±0.25
±2.5
±2.5
mA
5.5 V
4
40
40
mA
5.5 V
2
2.2
2.2
mA
10
pF
VI = VCC or GND
5V
3
10
Co
VO = VCC or GND
5V
5.5
* On products compliant to MIL-PRF-38535, this parameter is not production tested at VCC = 0 V.
† This is the increase in supply current for each input at one of the specified TTL voltage levels, rather than 0 V or VCC.
V
pF
timing requirements over recommended operating free-air temperature range, VCC = 5 V ± 0.5 V
(unless otherwise noted) (see Figure 1)
TA = 25°C
MIN
MAX
tw
tsu
Pulse duration
Setup time
SN54AHCT595
MIN
MAX
SN74AHCT595
MIN
SRCLK high or low
5
5.5
5.5
RCLK high or low
5
5.5
5.5
SRCLR low
5
5
5
SER before SRCLK↑
3
3
3
SRCLK↑ before RCLK↑‡
5
5
5
SRCLR low before RCLK↑
5
5
5
3.4
3.8
3.8
SRCLR high (inactive) before SRCLK↑
MAX
UNIT
ns
ns
th
Hold time
SER after SRCLK↑
2
2
2
ns
‡ This setup time allows the storage register to receive stable data from the shift register. The clocks can be tied together, in which case the shift
register is one clock pulse ahead of the storage register.
2 &(!)$'!& "!&"%)& *)!#" & % (!)$'3% !)
%1& *'% !( %3%,!*$%&- ')'"%)" '' '& !%)
*%"("'!& ')% %1& 1!',- %.' &)#$%& )%%)3% % )1 !
"'&1% !) "!&&#% %% *)!#" /!# &!"%-
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCLS374L − MAY 1997 − REVISED FEBRUARY 2004
switching characteristics over recommended operating free-air temperature range,
VCC = 5 V ± 0.5 V (unless otherwise noted) (see Figure 1)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
fmax
TA = 25°C
TYP
MAX
SN54AHCT595
SN74AHCT595
LOAD
CAPACITANCE
MIN
CL = 15 pF
135*
170*
115*
115
CL = 50 pF
95
140
85
85
tPLH
tPHL
RCLK
QA−QH
CL = 15 pF
tPLH
tPHL
SRCLK
QH′
H
CL = 15 pF
tPHL
SRCLR
QH′
CL = 15 pF
tPZH
tPZL
OE
QA−QH
CL = 15 pF
tPLH
tPHL
RCLK
QA−QH
CL = 50 pF
tPLH
tPHL
SRCLK
QH′
H
CL = 50 pF
tPHL
SRCLR
QH′
CL = 50 pF
tPZH
tPZL
OE
QA−QH
CL = 50 pF
tPHZ
tPLZ
OE
QA−QH
CL = 50 pF
MIN
MAX
MIN
MAX
UNIT
MHz
4.3*
7.4*
1*
8.5*
1
8.5
4.3*
7.4*
1*
8.5*
1
8.5
4.5*
8.2*
1*
9.4*
1
9.4
4.5*
8.2*
1*
9.4*
1
9.4
4.5*
8*
1*
9.1*
1
9.1
4.3*
8.6*
1*
10*
1
10
5.4*
8.6*
1*
10*
1
10
5.6
9.4
1
10.5
1
10.5
5.6
9.4
1
10.5
1
10.5
6.4
10.2
1
11.4
1
11.4
6.4
10.2
1
11.4
1
11.4
6.4
10
1
11.1
1
11.1
5.7
10.6
1
12
1
12
6.8
10.6
1
12
1
12
3.5
10.3
1
11
1
11
3.4
10.3
1
11
1
11
ns
ns
ns
ns
ns
ns
ns
ns
ns
* On products compliant to MIL-PRF-38535, this parameter is not production tested.
noise characteristics, VCC = 5 V, CL = 50 pF, TA = 25°C (see Note 4)
SN74AHCT595
PARAMETER
MIN
TYP
MAX
UNIT
VOL(P)
VOL(V)
Quiet output, maximum dynamic VOL
1
V
Quiet output, minimum dynamic VOL
−0.6
V
VOH(V)
VIH(D)
Quiet output, minimum dynamic VOH
3.8
V
High-level dynamic input voltage
2
VIL(D)
Low-level dynamic input voltage
NOTE 4: Characteristics are for surface-mount packages only.
V
0.8
V
TYP
UNIT
112
pF
operating characteristics, VCC = 5 V, TA = 25°C
PARAMETER
Cpd
TEST CONDITIONS
Power dissipation capacitance
No load,
f = 1 MHz
2 &(!)$'!& "!&"%)& *)!#" & % (!)$'3% !)
%1& *'% !( %3%,!*$%&- ')'"%)" '' '& !%)
*%"("'!& ')% %1& 1!',- %.' &)#$%& )%%)3% % )1 !
"'&1% !) "!&&#% %% *)!#" /!# &!"%-
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SCLS374L − MAY 1997 − REVISED FEBRUARY 2004
PARAMETER MEASUREMENT INFORMATION
From Output
Under Test
RL = 1 kΩ S1
From Output
Under Test
Test
Point
VCC
Open
TEST
GND
CL
(see Note A)
CL
(see Note A)
S1
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
Open Drain
Open
VCC
GND
VCC
LOAD CIRCUIT FOR
3-STATE AND OPEN-DRAIN OUTPUTS
LOAD CIRCUIT FOR
TOTEM-POLE OUTPUTS
3V
1.5 V
Timing Input
0V
tw
3V
1.5 V
Input
1.5 V
th
tsu
3V
1.5 V
Data Input
1.5 V
0V
0V
VOLTAGE WAVEFORMS
PULSE DURATION
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
3V
1.5 V
Input
1.5 V
0V
tPLH
In-Phase
Output
tPHL
50% VCC
tPHL
Out-of-Phase
Output
VOH
50% VCC
VOL
Output
Waveform 1
S1 at VCC
(see Note B)
VOH
50% VCC
VOL
1.5 V
tPLZ
≈VCC
50% VCC
Output
Waveform 2
S1 at GND
(see Note B)
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
1.5 V
0V
tPZL
tPZH
tPLH
50% VCC
3V
Output
Control
VOL + 0.3 V
VOL
tPHZ
50% VCC
VOH − 0.3 V
VOH
≈0 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr ≤ 3 ns, tf ≤ 3 ns.
D. The outputs are measured one at a time, with one input transition per measurement.
E. All parameters and waveforms are not applicable to all devices.
Figure 1. Load Circuit and Voltage Waveforms
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
18-Jul-2006
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
SN74AHCT595D
ACTIVE
SOIC
D
16
SN74AHCT595DBR
ACTIVE
SSOP
DB
SN74AHCT595DBRE4
ACTIVE
SSOP
SN74AHCT595DE4
ACTIVE
SN74AHCT595DR
40
Lead/Ball Finish
MSL Peak Temp (3)
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
DB
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SOIC
D
16
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74AHCT595DRE4
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74AHCT595N
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
SN74AHCT595NE4
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
SN74AHCT595NSR
ACTIVE
SO
NS
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74AHCT595NSRE4
ACTIVE
SO
NS
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74AHCT595PW
ACTIVE
TSSOP
PW
16
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74AHCT595PWE4
ACTIVE
TSSOP
PW
16
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74AHCT595PWR
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74AHCT595PWRE4
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
40
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
18-Jul-2006
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
DB (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
28 PINS SHOWN
0,38
0,22
0,65
28
0,15 M
15
0,25
0,09
8,20
7,40
5,60
5,00
Gage Plane
1
14
0,25
A
0°–ā8°
0,95
0,55
Seating Plane
2,00 MAX
0,10
0,05 MIN
PINS **
14
16
20
24
28
30
38
A MAX
6,50
6,50
7,50
8,50
10,50
10,50
12,90
A MIN
5,90
5,90
6,90
7,90
9,90
9,90
12,30
DIM
4040065 /E 12/01
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-150
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Low Power Wireless www.ti.com/lpw
Mailing Address:
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2006, Texas Instruments Incorporated