DS1305 Serial Alarm Real Time Clock (RTC) www.dalsemi.com FEATURES PIN ASSIGNMENT Real time clock counts seconds, minutes, hours, date of the month, month, day of the week and year with leap year compensation valid up to 2100 96-byte nonvolatile RAM for data storage Two time-of-day alarms programmable on combination of seconds, minutes, hours and day of the week Serial interface supports Motorola serial peripheral interface (SPI) serial data ports or standard 3-wire interface Burst mode for reading/writing successive addresses in clock/RAM Dual power supply pins for primary and backup power supplies Optional trickle charge output to backup supply 2.0 - 5.5V operation Optional industrial temperature range -40°C to +85°C Available in space-efficient, 20-pin TSSOP package Recognized by Underwriters Laboratory VCC2 1 20 VCC1 VBAT 2 19 NC X1 3 18 PF NC 4 17 VCCIF X2 5 16 SD0 NC 6 15 SDI INT0 7 14 SCLK NC 8 13 NC INT1 9 12 CE GND 10 11 SERMODE DS1305 20-Pin TSSOP (173 mil) ORDERING INFORMATION DS1305 DS1305N DS1305E DS1305EN 16-Pin DIP 16-Pin DIP (Industrial) 20-Pin TSSOP 20-Pin TSSOP (Industrial) VCC2 1 16 VCC1 VBAT 2 15 PF X1 3 14 VCCIF X2 4 13 SDO NC 5 12 SDI INT0 6 11 SCLK INT1 7 10 CE GND 8 9 SERMODE DS1305 16-Pin DIP (300 mil) 1 of 22 070900 DS1305 PIN DESCRIPTION VCC1 VCC2 VBAT VCCIF GND X1, X2 - Primary Power Supply - Backup Power Supply - +3V Battery Input - Interface Logic Power Supply Input - Ground - 32.768 kHz Crystal Connection INT0 - Interrupt 0 Output INT1 - Interrupt 1 Output SDI - Serial Data In SDO - Serial Data Out CE - Chip Enable SCLK - Serial Clock SERMODE - Serial Interface Mode PF - Power Fail Output DESCRIPTION The DS1305 Serial Alarm Real Time Clock provides a full BCD clock calendar which is accessed via a simple serial interface. The clock/calendar provides seconds, minutes, hours, day, date, month and year information. The end of the month date is automatically adjusted for months with less than 31 days, including corrections for leap year. The clock operates in either the 24-hour or 12-hour format with AM/PM indicator. In addition 96 bytes of nonvolatile RAM are provided for data storage. An interface logic power supply input pin (VCCIF) allows the DS1305 to drive SDO and PF pins to a level that is compatible with the interface logic. This allows an easy interface to 3-volt logic in mixed supply systems. The DS1305 offers dual power supplies as well as a battery input pin. The dual power supplies support a programmable trickle charge circuit which allows a rechargeable energy source (such as a super cap or rechargeable battery) to be used for a backup supply. The VBAT pin allows the device to be backed up by a non-rechargeable battery. The DS1305 is fully operational from 2.0 to 5.5 volts. Two programmable time of day alarms are provided by the DS1305. Each alarm can generate an interrupt on a programmable combination of seconds, minutes, hours and day. “Don’t care” states can be inserted into one or more fields if it is desired for them to be ignored for the alarm condition. The time of day alarms can be programmed to assert two different interrupt outputs or to assert one common interrupt output. Both interrupt outputs operate when the device is powered by VCC1, VCC2, or VBAT. The DS1305 supports a direct interface to Motorola SPI serial data ports or standard 3-wire interface. A straightforward address and data format is implemented in which data transfers can occur 1 byte at a time or in multiple-byte burst mode. OPERATION The block diagram in Figure 1 shows the main elements of the Serial Alarm RTC. The following paragraphs describe the function of each pin. 2 of 22 DS1305 DS1305 BLOCK DIAGRAM Figure 1 SIGNAL DESCRIPTIONS VCC1 - DC power is provided to the device on this pin. VCC1 is the primary power supply. VCC2 - This is the secondary power supply pin. In systems using the trickle charger, the rechargeable energy source is connected to this pin. VBAT - Battery input for any standard 3-volt lithium cell or other energy source. VCCIF (Interface Logic Power Supply Input) - The VCCIF pin allows the DS1305 to drive SDO and PF out-put pins to a level that is compatible with the interface logic, thus allowing an easy interface to 3-volt logic in mixed supply systems. This pin is physically connected to the source connection of the p-channel transistors in the output buffers of the SDO and PF pins. SERMODE (Serial Interface Mode Input) - The SERMODE pin offers the flexibility to choose between two serial interface modes. When connected to GND, standard 3-wire communication is selected. When connected to VCC, Motorola SPI communication is selected. SCLK (Serial Clock Input) - SCLK is used to synchronize data movement on the serial interface for either the SPI or 3-wire interface. SDI (Serial Data Input) - When SPI communication is selected, the SDI pin is the serial data input for the SPI bus. When 3-wire communication is selected, this pin must be tied to the SDO pin (the SDI and SDO pins function as a single I/O pin when tied together). SDO (Serial Data Output) - When SPI communication is selected, the SDO pin is the serial data output for the SPI bus. When 3-wire communication is selected, this pin must be tied to the SDI pin (the SDI and SDO pins function as a single I/O pin when tied together). 3 of 22 DS1305 CE (Chip Enable) - The Chip Enable signal must be asserted high during a read or a write for both 3wire and SPI communication. This pin has an internal 55K pull-down resistor (typical). INT0 (Interrupt 0 Output) - The INT0 pin is an active low output of the DS1305 that can be used as an interrupt input to a processor. The INT0 pin can be programmed to be asserted by only Alarm 0 or can be programmed to be asserted by either Alarm 0 or Alarm 1. The INT0 pin remains low as long as the status bit causing the interrupt is present and the corresponding interrupt enable bit is set. The INT0 pin operates when the DS1305 is powered by VCC1, VCC2, or VBAT. The INT0 pin is an open drain output and requires an external pull-up resistor. INT1 (Interrupt 1 Output) - The INT1 pin is an active low output of the DS1305 that can be used as an interrupt input to a processor. The INT1 pin can be programmed to be asserted by Alarm 1 only. The INT1 pin remains low as long as the status bit causing the interrupt is present and the corresponding interrupt enable bit is set. The INT1 pin operates when the DS1305 is powered by VCC1, VCC2, or VBAT. The INT1 pin is an open drain output and requires an external pull-up resistor. Both INT0 and INT1 are open drain outputs. The two interrupts and the internal clock continue to run regardless of the level of VCC (as long as a power source is present). (Power Fail Output) - The PF pin is used to indicate loss of the primary power supply (VCC1). When VCC1 is less than VCC2 or is less than VBAT , the PF pin will be driven low. PF X1, X2 - Connections for a standard 32.768 kHz quartz crystal. The internal oscillator is designed for operation with a crystal having a specified load capacitance of 6 pF. For more information on crystal selection and crystal layout considerations, please consult Application Note 58, “Crystal Considerations with Dallas Real Time Clocks.” The DS1305 can also be driven by an external 32.768 kHz oscillator. In this configuration, the X1 pin is connected to the external oscillator signal and the X2 pin is floated. 4 of 22 DS1305 RTC AND RAM ADDRESS MAP The address map for the RTC and RAM registers of the DS1305 is shown in Figure 2. Data is written to the RTC by writing to address locations 80h to 9Fh and is written to the RAM by writing to address locations A0h to FFh. RTC data is read by reading address locations 00h to 1Fh and RAM data is read by reading address locations 20h to 7Fh. ADDRESS MAP Figure 2 00H CLOCK/CALENDAR 1FH 20H READ ADDRESSES ONLY 96-BYTES USER RAM 7FH 80H READ ADDRESSES ONLY CLOCK/CALENDAR 9FH A0H WRITE ADDRESSES ONLY 96-BYTES USER RAM FFH WRITE ADDRESSES ONLY CLOCK, CALENDAR AND ALARM The time and calendar information is obtained by reading the appropriate register bytes. The real time clock registers are illustrated in Figure 3. The time, calendar and alarm are set or initialized by writing the appropriate register bytes. Note that some bits are set to zero. These bits will always read 0 regardless of how they are written. Also note that registers 12h to 1Fh (read) and registers 92h to 9Fh are reserved. These registers will always read 0 regardless of how they are written. The contents of the time, calendar and alarm registers are in the binary-coded decimal (BCD) format. Please note that the initial power on state of all registers in not defined. Therefore it is important to enable the oscillator (EOSC = 0) and disable write protect (WP = 0) during initial configuration. 5 of 22 DS1305 RTC REGISTERS Figure 3 RTC Registers DS1305 HEX ADDRESS READ WRITE 00H 80H 01H 81H 02H 82H Bit7 0 0 0 03H 04H 05H 06H 83H 84H 85H 86H 0 0 0 07H 08H 09H 87H 88H 89H M M M 0AH 8AH M 0BH 0CH 0DH 8BH 8CH 8DH M M M 0EH 0FH 10H 11H 12-1FH 8EH 8FH 90H 91H 92-9FH M Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 10 SEC SEC 10 MIN MIN 12/2 10 10 HR HOURS 4 P/A 0 0 0 DAY 0 10 DATE DATE 0 10 MONTH MONTH 10 YEAR YEAR Alarm 0 10 SEC ALARM SEC ALARM 10 MIN ALARM MIN ALARM 12/2 10 10 HR HOUR ALARM 4 P/A 0 0 0 DAY ALARM Alarm 1 10 SEC ALARM SEC ALARM 10 MIN ALARM MIN ALARM 12/2 10 10 HR HOUR ALARM 4 P/A 0 0 0 DAY ALARM CONTROL REGISTER STATUS REGISTER TRICKLE CHARGER REGISTER RESERVED Bit0 RANGE 00-59 00-59 01-12 + P/A 00-23 01-07 1-31 01-12 00-99 00-59 00-59 01-12 + P/A 00-23 01-07 00-59 00-59 01-12 + P/A 00-23 01-07 Range For Alarm Registers Does Not Include Mask’m’ Bits. The DS1305 can be run in either 12-hour or 24-hour mode. Bit 6 of the hours register is defined as the 12- or 24-hour mode select bit. When high, the 12-hour mode is selected. In the 12-hour mode, bit 5 is the AM/PM bit with logic high being PM. In the 24-hour mode, bit 5 is the second 10-hour bit (20-23 hours). The DS1305 contains two time of day alarms. Time of Day Alarm 0 can be set by writing to registers 87h to 8Ah. Time of Day Alarm 1 can be set by writing to registers 8Bh to 8Eh. The alarms can be programmed (by the INTCN bit of the Control Register) to operate in two different modes - each alarm can drive its own separate interrupt output or both alarms can drive a common interrupt output. Bit 7 of each of the time of day alarm registers are mask bits (Table 1). When all of the mask bits are logic 0, a time of day alarm will only occur once per week when the values stored in timekeeping registers 00h to 03h match the values stored in the time of day alarm registers. An alarm will be generated every day when bit 7 of the day alarm register is set to a logic 1. An alarm will be generated every hour when bit 7 of the day and hour alarm registers is set to a logic 1. Similarly, an alarm will be generated every minute when bit 7 of the day, hour and minute alarm registers is set to a logic 1. When bit 7 of the day, hour, minute and seconds alarm registers is set to a logic 1, alarm will occur every second. 6 of 22 DS1305 TIME OF DAY ALARM MASK BITS Table 1 ALARM REGISTER MASK BITS (BIT 7) SECONDS MINUTES HOURS DAYS 1 1 1 1 0 1 1 1 0 0 1 1 0 0 0 1 0 0 0 0 Alarm once per second Alarm when seconds match Alarm when minutes and seconds match Alarm hours, minutes and seconds match Alarm day, hours, minutes and seconds match SPECIAL PURPOSE REGISTERS The DS1305 has three additional registers (Control Register, Status Register and Trickle Charger Register) that control the real time clock, interrupts and trickle charger. CONTROL REGISTER (READ 0FH, WRITE 8FH) BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0 EOSC WP 0 0 0 INTCN AIE1 AIE0 EOSC (Enable oscillator) - This bit when set to logic 0 will start the oscillator. When this bit is set to a logic 1, the oscillator is stopped and the DS1305 is placed into a low-power standby mode with a current drain of less than 100 nanoamps when power is supplied by VBAT or VCC2 . The initial power on state is not defined. WP (Write Protect) - Before any write operation to the clock or RAM, this bit must be logic 0. When high, the write protect bit prevents a write operation to any register, including bits 0, 1, 2 and 7 of the control register. Upon initial power up, the state of the WP bit is undefined. Therefore the WP bit should be cleared before attempting to write to the device. INTCN (Interrupt Control) - This bit controls the relationship between the two time of day alarms and the interrupt output pins. When the INTCN bit is set to a logic 1, a match between the timekeeping registers and the Alarm 0 registers will activate the INT0 pin (provided that the alarm is enabled) and a match between the timekeeping registers and the Alarm 1 registers will activate the INT1 pin (provided that the alarm is enabled). When the INTCN bit is set to a logic 0, a match between the timekeeping registers and either Alarm 0 or Alarm 1 will activate the INT0 pin (provided that the alarms are enabled). INT1 has no function when INTCN is set to a logic 0. AIE0 (Alarm Interrupt Enable 0) - When set to a logic 1, this bit permits the Interrupt 0 Request Flag (IRQF0) bit in the status register to assert INT0 . When the AIE0 bit is set to logic 0, the IRQF0 bit does not initiate the INT0 signal. AIE1 (Alarm Interrupt Enable 1) - When set to a logic 1, this bit permits the Interrupt 1 Request Flag (IRQF1) bit in the status register to assert INT1 (when INTCN=1) or to assert INT0 (when INTCN=0). When the AIE1 bit is set to logic 0, the IRQF1 bit does not initiate an interrupt signal. 7 of 22 DS1305 STATUS REGISTER (READ 10H) BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0 0 0 0 0 0 0 IRQF1 IRQF0 IRQF0 (Interrupt 0 Request Flag) - A logic 1 in the Interrupt Request Flag bit indicates that the current time has matched the Alarm 0 registers. If the AIE0 bit is also a logic 1, the INT0 pin will go low. IRQF0 is cleared when any of the Alarm 0 registers are read or written. IRQF1 (Interrupt 1 Request Flag) - A logic 1 in the Interrupt Request Flag bit indicates that the current time has matched the Alarm 1 registers. This flag can be used to generate an interrupt on either INT0 or INT1 depending on the status of the INTCN bit in the Control Register. If the INTCN bit is set to a logic 1 and IRQF1 is at a logic 1 (and AIE1 bit is also a logic 1), the INT1 pin will go low. If the INTCN bit is set to a logic 0 and IRQF1 is at a logic 1 (and AIE1 bit is also a logic 1), the INT0 pin will go low. IRQF1 is cleared when any of the Alarm 1 registers are read or written. TRICKLE CHARGE REGISTER (READ 11H, WRITE 91H) This register controls the trickle charge characteristics of the DS1305. The simplified schematic of Figure 4 shows the basic components of the trickle charger. The trickle charge select (TCS) bits (bits 4-7) control the selection of the trickle charger. In order to prevent accidental enabling, only a pattern of 1010 will enable the trickle charger. All other patterns will disable the trickle charger. The DS1305 powers up with the trickle charger disabled. The diode select (DS) bits (bits 2-3) select whether one diode or two diodes are connected between VCC1 and VCC2 . If DS is 01, one diode is selected. If DS is 10, two diodes are selected. If DS is 00 or 11, the trickle charger is disabled independent of TCS. The RS bits select the resistor that is connected between VCC1 and VCC2. The resistor is selected by the resister select (RS) bits as shown in Table 2. PROGRAMMABLE TRICKLE CHARGER Figure 4 8 of 22 DS1305 TRICKLE CHARGER RESISTOR SELECT Table 2 RS BITS RESISITORS TYPICAL VALUE 00 None None 01 R1 2 kΩ 10 R2 4 kΩ 11 R3 8 kΩ If RS is 00, the trickle charger is disabled independent of TCS. Diode and resistor selection is determined by the user according to the maximum current desired for battery or super cap charging. The maximum charging current can be calculated as illustrated in the following example. Assume that a system power supply of 5 volts is applied to VCC1 and a super cap is connected to VCC2 . Also assume that the trickle charger has been enabled with 1 diode and resister R1 between VCC1 and VCC2. The maximum current I MAX would therefore be calculated as follows: I MAX = ~ ~ (5.0V - diode drop)/R1 (5.0V - 0.7V)/2 kΩ 2.2 mA Obviously, as the super cap charges, the voltage drop between VCC1 and VCC2 will decrease and therefore the charge current will decrease. POWER CONTROL Power is provided through the VCC1, VCC2 and VBAT pins. Three different power supply configurations are illustrated in Figure 5. Configuration 1 shows the DS1305 being backed up by a non-rechargeable energy source such as a lithium battery. In this configuration, the system power supply is connected to VCC1 and VCC2 is grounded. The DS1305 will be write protected if VCC1 is less than VBAT . Configuration 2 illustrates the DS1305 being backed up by a rechargeable energy source. In this case, the VBAT pin is grounded, VCC1 is connected to the primary power supply and VCC2 is connected to the secondary supply (the rechargeable energy source). The DS1305 will operate from the larger of VCC1 or VCC2. When VCC1 is greater than VCC2 + 0.2 volt (typical), VCC1 will power the DS1305. When VCC1 is less than VCC2, VCC2 will power the DS1305. The DS1305 does not write protect itself in this configuration. Configuration 3 shows the DS1305 in battery operate mode where the device is powered only by a single battery. In this case, the VCC1 and VBAT pins are grounded and the battery is connected to the VCC2 pin. Only these three configurations are allowed. Unused supply pins must be grounded. SERIAL INTERFACE The DS1305 offers the flexibility to choose between two serial interface modes. The DS1305 can communicate with the SPI interface or with a standard 3-wire inter-face. The interface method used is determined by the SERMODE pin. When this pin is connected to VCC, SPI communication is selected. When this pin is connected to ground, standard 3-wire communication is selected. 9 of 22 DS1305 SERIAL PERIPHERAL INTERFACE (SPI) The serial peripheral interface (SPI) is a synchronous bus for address and data transfer and is used when interfacing with the SPI bus on specific Motorola microcontrollers such as the 68HC05C4 and the 68HC11A8. The SPI mode of serial communication is selected by tying the SERMODE pin to VCC. Four pins are used for the SPI. The four pins are the SDO (Serial Data Out), SDI (Serial Data In), CE (Chip Enable) and SCLK (Serial Clock). The DS1305 is the slave device in an SPI application, with the microcontroller being the master. The SDI and SDO pins are the serial data input and output pins for the DS1305, respectively. The CE input is used to initiate and terminate a data transfer. The SCLK pin is used to synchronize data movement between the master (microcontroller) and the slave (DS1305) devices. The shift clock (SCLK), which is generated by the microcontroller, is active only during address and data transfer to any device on the SPI bus. The inactive clock polarity is programmable in some microcontrollers. The DS1305 offers an important feature in that the level of the inactive clock is determined by sampling SCLK when CE becomes active. Therefore either SCLK polarity can be accommodated. Input data (SDI) is latched on the internal strobe edge and output data (SDO) is shifted out on the shift edge (see Table 3 and Figure 6). There is one clock for each bit transferred. Address and data bits are transferred in groups of eight. POWER SUPPLY CONFIGURATIONS FOR THE DS1305 Figure 5 Configuration 1: Backup Supply is a Non-Rechargeable Lithium Battery 10 of 22 DS1305 Configuration 2: Backup Supply is a Rechargeable Battery or Super Capacitor Configuration 3: Battery Operate Mode FUNCTION TABLE Table 3 MODE CE SCLK SDI SDO Disable Reset L Input Disabled Input Disabled High Z Write H CPOL=1* Data Bit Latch High Z X Next data bit shift** CPOL=0 Read H CPOL=1 CPOL=0 * CPOL is the “Clock Polarity” bit that is set in the control register of the microcontroller. ** SDO remains at High Z until 8 bits of data are ready to be shifted out during a read. 11 of 22 DS1305 NOTE: CPHA bit polarity (if applicable) may need to be set accordingly. SERIAL CLOCK AS A FUNCTION OF MICROCONTROLLER CLOCK POLARITY (CPOL) Figure 6 CE CPOL = 1 SHIFT INTERNAL STROBE SHIFT INTERNAL STROBE SCLK CE CPOL = 0 SCLK NOTE: CPOL is a bit that is set in the microcontroller’s Control Register. ADDRESS AND DATA BYTES Address and data bytes are shifted MSB first into the serial data input (SDI) and out of the serial data output (SDO). Any transfer requires the address of the byte to specify a write or read to either a RTC or RAM location, followed by one or more bytes of data. Data is transferred out of the SDO for a read operation and into the SDI for a write operation (see Figure 7 and 8). SPI SINGLE-BYTE WRITE Figure 7 12 of 22 DS1305 SPI SINGLE-BYTE READ Figure 8 *SCLK can be either polarity. The address byte is always the first byte entered after CE is driven high. The most significant bit (A7) of this byte determines if a read or write will take place. If A7 is 0, one or more read cycles will occur. If A7 is 1, one or more write cycles will occur. Data transfers can occur 1 byte at a time or in multiple-byte burst mode. After CE is driven high an address is written to the DS1305. After the address, one or more data bytes can be written or read. For a single-byte transfer 1 byte is read or written and then CE is driven low. For a multiple-byte transfer, however, multiple bytes can be read or written to the DS1305 after the address has been written. Each read or write cycle causes the RTC register or RAM address to automatically increment. Incrementing continues until the device is disabled. When the RTC is selected, the address wraps to 00h after incrementing to 1Fh (during a read) and wraps to 80h after incrementing to 9Fh (during a write). When the RAM is selected, the address wraps to 20h after incrementing to 7Fh (during a read) and wraps to A0h after incrementing to FFh (during a write). SPI MULTIPLE-BYTE BURST TRANSFER Figure 9 13 of 22 DS1305 3-WIRE INTERFACE The 3-wire interface mode operates similarly to the SPI mode. However, in 3-wire mode there is one I/O instead of separate data in and data out signals. The 3-wire interface consists of the I/O (SDI and SDO pins tied together), CE and SCLK pins. In 3-wire mode, each byte is shifted in LSB first unlike SPI mode where each byte is shifted in MSB first. As is the case with the SPI mode, an address byte is written to the device followed by a single data byte or multiple data bytes. Figure 10 illustrates a read and write cycle. In 3-wire mode, data is input on the rising edge of SCLK and output on the falling edge of SCLK. 3-WIRE SINGLE-BYTE TRANSFER Figure 10 Single Byte Read RST SCLK I/O A0 A1 A2 A3 A4 A5 A6 A7 Single Byte Write RST SCLK I/O A0 A1 A2 A3 A4 A5 A6 A7 D0 D1 D2 D3 D4 D5 D6 D7 In burst mode, RST is kept high and additional SCLK cycles are sent until the end of the burst. * I/O is SDI and SDO tied together 14 of 22 DS1305 ABSOLUTE MAXIMUM RATINGS* Voltage on Any Pin Relative to Ground Operating Temperature Storage Temperature Soldering Temperature -0.5V to +7.0V 0°C to 70°C or -40°C to +85°C -55°C to +125°C 260°C for 10 seconds (DIP) See IPC/JEDEC Standard J-STD-020A for Surface Mount Devices * This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. RECOMMENDED DC OPERATING CONDITIONS (0°C to 70°C or –40°C to +85°C) PARAMETER SYMBOL Supply Voltage VCC1, VCC2 Logic 1 Input Logic 0 Input VCC1, VCC2 VIH VIL VBAT Battery Voltage VCCIF Supply Voltage VBAT VCCIF VCC=2.0V VCC=5V MIN MAX UNITS NOTES 2.0 5.5 V 1,9 2.0 -0.3 -0.3 2.0 2.0 VCC+0.3 +0.3 +0.8 5.5 5.5 V V 1 1 V V 1 14 15 of 22 TYP DS1305 DC ELECTRICAL CHARACTERISTICS (0°C to 70°C or –40°C to +85°C; VCC = 2.0 to 5.5V*) PARAMETER SYMBOL Input Leakage Output Leakage Logic 0 Output ILI ILO VOL Logic 1 Output VOH VCC1 Active Supply Current ICC1A VCC1 Timekeeping Current ICC1T VCC1 Standby Current ICC1S VCC2 Active Supply Current ICC2A VCC2 Timekeeping Current ICC2T VCC2 Standby Current ICC2S Battery Timekeeping Current Battery Standby Current Trickle Charge Resistors IBATT IBATS R1 R2 R3 Trickle Charge Diode Voltage Drop VTD MIN TYP -100 -1 VCC=2.0V VCC=5V VCCIF=2.0V VCCIF=5V VCC1=2.0V VCC1=5V VCC1=2.0V VCC1=5V VCC1=2.0V VCC1=5V VCC2=2.0V VCC2=5V VCC2=2.0V VCC2=5V VCC2=2.0V VCC2=5V VBAT=3V VBAT=3V MAX UNITS NOTES +500 1 0.4 0.4 µA µA V 2 V 13 mA 4,10 µA 3,10 µA 8,10 mA 4,11 µA 3,11 nA 8,11 nA nA kΩ kΩ kΩ V 12 12 1.6 2.4 0.425 1.28 25.3 81 25 80 0.4 1.2 0.3 1 200 200 400 200 2 4 8 0.7 *Unless otherwise noted. CAPACITANCE PARAMETER Input Capacitance Output Capacitance Crystal Capacitance (tA = 25°C) SYMBOL CI CO CX CONDITION TYP 10 15 6 16 of 22 MAX UNITS pF pF pF NOTES DS1305 3-WIRE AC ELECTRICAL CHARACTERISTICS (0°C to 70°C or –40°C to +85°C; VCC = 2.0 to 5.5V*) PARAMETER SYMBOL Data to CLK Setup tDC CLK to Data Hold tCDH CLK to Data Delay tCDD CLK Low Time tCL CLK High Time tCH CLK Frequency tCLK CLK Rise and Fall tR, tF CE to CLK Setup tCC CLK to CE Hold tCCH CE Inactive Time tCWH CE to Output High Z tCDZ SCLK to Output High Z tCCZ VCC=2.0V VCC=5V VCC=2.0V VCC=5V VCC=2.0V VCC=5V VCC=2.0V VCC=5V VCC=2.0V VCC=5V VCC=2.0V VCC=5V VCC=2.0V VCC=5V VCC=2.0V VCC=5V VCC=2.0V VCC=5V VCC=2.0V VCC=5V VCC=2.0V VCC=5V VCC=2.0V VCC=5V MIN TYP MAX 200 50 280 70 800 200 1000 250 1000 250 DC 0.6 2.0 2000 500 4 1 240 60 4 1 280 70 280 70 *Unless otherwise noted. TIMING DIAGRAM: 3-WIRE READ DATA TRANSFER Figure 12 17 of 22 UNITS NOTES ns 5,6 ns 5,6 ns 5,6,7 ns 6 ns 6 MHz 6 ns µs 6 ns 6 µs 6 ns 5,6 ns 5,6 DS1305 TIMING DIAGRAM: 3-WIRE WRITE DATA TRANSFER Figure 13 SPI AC ELECTRICAL CHARACTERISTICS (0°C to 70°C or -40°C to +85°C; VCC = 2.0 to 5.5V*) PARAMETER SYMBOL Data to CLK Setup tDC CLK to Data Hold tCDH CLK to Data Delay tCDD CLK Low Time tCL CLK High Time tCH CLK Frequency tCLK CLK Rise and Fall tR, tF CE to CLK Setup tCC CLK to CE Hold tCCH CE Inactive Time tCWH CE to Output High Z tCDZ VCC=2.0V VCC=5V VCC=2.0V VCC=5V VCC=2.0V VCC=5V VCC=2.0V VCC=5V VCC=2.0V VCC=5V VCC=2.0V VCC=5V VCC=2.0V VCC=5V VCC=2.0V VCC=5V VCC=2.0V VCC=5V VCC=2.0V VCC=5V VCC=2.0V VCC=5V MIN TYP MAX 200 50 280 70 800 200 1000 250 1000 250 DC 0.6 2.0 2000 500 4 1 240 60 4 1 280 70 * Unless otherwise noted. 18 of 22 UNITS NOTES ns 5,6 ns 5,6 ns 5,6,7 ns 6 ns 6 MHz 6 ns µs 6 ns 6 µs 6 ns 5,6 DS1305 TIMING DIAGRAM: SPI READ DATA TRANSFER Figure 14 TIMING DIAGRAM: SPI WRITE DATA TRANSFER Figure 15 19 of 22 DS1305 NOTES 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. All voltages are referenced to ground. Logic 0 voltages are specified at a sink current of 4 mA at VCC =5V and 1.5 mA at VCC =2.0V, VOL =GND for capacitive loads. ICC1T and ICC2T are specified with CE set to a logic 0 and EOSC bit=0 (oscillator enabled). ICC1A and ICC2A are specified with CE=VCC, SCLK=2 MHz (0-VCC) at VCC =5V; SCLK=500 kHz (0-5V) at VCC =2.0V and EOSC bit=0 (oscillator enabled). Measured at VIH =2.0V or VIL =0.8V and 10 ms maximum rise and fall time. Measured with 50 pF load. Measured at VOH =2.4V or VOL =0.4V. ICC1S and ICC2S are specified with CE set to a logic 0. The EOSC bit must be set to logic 1 (oscillator disabled). VCC =VCC1 , when VCC1 >VCC2 +0.2V (typical); VCC =VCC2, when VCC2 >VCC1. VCC2 =0V. VCC1 =0V. VCC1<VBAT. Logic one voltages are specified at a source current of 1 mA at VCC =5V and 0.4 mA at 2.0V, VOH =VCC. VCCIF must be less than or equal to the largest of VCC1, VCC2 and VBAT . 20 of 22 DS1305 DS1305 16-PIN DIP (300-MIL) PKG 16-PIN DIM MIN MAX A IN 0.740 0.780 MM 18.80 19.81 B IN MM 0.240 6.10 0.260 6.60 C IN 0.120 0.140 MM 3.05 3.56 D IN 0.300 0.325 MM 7.62 8.26 E IN 0.015 0.040 MM 0.38 1.02 F IN 0.120 0.140 MM 3.05 3.56 G IN 0.090 0.110 MM 2.29 2.79 H IN 0.320 0.370 MM 8.13 9.40 J IN 0.008 0.012 MM 0.20 0.30 K IN MM 0.015 0.38 0.021 0.53 21 of 22 DS1305 DS1305 20-PIN TSSOP DIM MIN MAX A MM - 1.10 A1 MM 0.05 - A2 MM 0.75 1.05 C MM 0.09 0.18 L MM 0.50 0.70 0.65 BSC e1 MM B MM 0.18 0.30 D MM 6.40 6.90 E MM 4.40 NOM G MM 0.25 REF H MM 6.25 6.55 phi 0° 8° 22 of 22