55 Commerce Way Woburn, MA 01801 (781) 935 - 4442 (781) 938 - 5867 www.gilway.com GHB-0805DU-Y GHB-0805DU-O GHB-0805DU-R GHB-0805DU-R2 CATHODE MARK LED DIE 1.25 (0.049) 2.0 (0.079Ê) 1.4 (0.055) DIFFUSED EPOXY 0.62 (0.024) POLARITY 0.3 (0.012) PC BOARD CATHODE LINE 0.4 ± 0.15 (0.016 ± 0.006) Description These chip-type LEDs utilize Aluminum Indium Gallium Phosphide (AlInGaP) material technology. The AlInGaP material has a very high luminous efficiency, capable of producing high light output over a wide range of drive currents. The available colors in this surface mount series are 592 nm Amber, 605 nm Orange, 626 nm Red for AS AlInGaP and 631 nm red for TS AlInGaP. 0.8 (0.031) 0.3 (0.012) 0.4 ± 0.15 (0.016 ± 0.006) SOLDERING TERMINAL Device Selection Guide Footprint (mm)[1,2] AS AlInGaP Amber 2.0 x 1.25 x 0.8 GHB-0805DU-Y AS AlInGaP Orange AS AlInGaP Red TS AlInGaP Red GHB-0805DU-O GHB-0805DU-R GHB0805DU-R2 Package Description Untinted, Diffused Notes: 1. Dimensions in mm. 2. Tolerance ± 0.1 mm unless otherwise noted. T bsolute Maximum Ratings A °C A = 25 Parameter DC Forward Current GHB-0805DU-Y GHB-0805DU-O GHB-0805DU-R GHB-0805DU-R2 30 30 [1,2] Power Dissipation Reverse Voltage (I mA 75 81 mW 5 5 V 95 95 °C R = 100mA) LED Junction Temperature Units Operating Temperature Range Ð30 to +85 Ð30 to +85 °C Storage Temperature Range Ð40 to +85 Ð40 to +85 °C Soldering Temperature See IR soldering profile (Figure 7) Notes: 1. Derate linearly as shown in Figure 4. 2. Drive currents above 5 mA are recommended for best long term performance. Electrical Characteristics TA = 25°C Parameter Number Forward Voltage VF (Volts) @ IF = 20 mA Typ. Max. Reverse Breakdown V R (Volts) @RI = 100mA Min. Capacitance C (pF), VF = 0, f = 1 MHz Typ. Thermal Resistance RqJ-PIN = °(C/W) Typ. GHB-0805DU-Y 1.9 2.4 5 45 300 GHB-0805DU-O 1.9 2.4 5 45 300 GHB-0805DU-R 1.9 2.4 5 45 300 2.6 5 35 300 GHB-0805DU-R2 2.2 Optical Characteristics TA = 25°C Color Luminous Intensity I v (mcd) @ 20 mA[1] Min. Typ. GHB-0805DU-Y AS Amber 25 90 595 592 170 480 GHB-0805DU-O GHB-0805DU-R AS Orange AS Red 25 25 90 90 609 637 605 626 170 170 370 155 40 165 643 631 170 122 Part Number GHB-0805DU-R2 TS Red Peak Wavelength lpeak (nm) Typ. Color, Dominant Wavelength ld[2] (nm) Typ. Viewing Luminous Angle Efficacy 2 q1/2 hv Degrees[3] (lm/w) Typ. Typ. Notes: 1. The luminous intensity, I v, is measured at the peak of the spatial radiation pattern which may not be aligned with the mechanical axis of the lamp package. 2. The dominant wavelength, ld , is derived from the CIE Chromaticity Diagram and represents the perceived color of the device. 3. q 1/2 is the off-axis angle where the luminous intensity is 1/2 the peak intensity. 1.0 100 RELATIVE INTENSITY IF Ð FORWARD CURRENT Ð mA RE A SD AlInGaP AS AlInGaP AMBER AS AlInGaP ORANGE 0.5 TS AlInGaP RED 0 500 550 600 650 700 IF MAX. Ð MAXIMUM FORWARD CURRENT Ð mA 1.0 0.8 0.6 0.4 0.2 10 15 20 25 30 IF Ð FORWARD CURRENT Ð mA 1.00 35 30 25 20 RqJ-A = 800¡C/W 15 RqJ-A = 600¡C/W 10 RqJ-A = 500¡C/W 5 0 0 20 40 60 80 0.80 0.70 0.60 0.50 0.40 0.30 0.20 0.10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 ANGLE 100 TA Ð AMBIENT TEMPERATURE Ð ¡C 0.90 RELATIVE INTENSITY LUMINOUS INTENSITY (NORMALIZED AT 20 mA) 1.2 5 TS AlInGaP 1 1.5 1.7 1.9 2.1 2.3 V F Ð FORWARD VOLTAGE Ð V 1.4 0 10 0.1 750 WAVELENGTH Ð nm 0 AS AlInGaP 80 90 2.5 1.2 (0.047) 1.2 (0.047) 1.2 (0.047) 0.9 (0.035) Recommended soldering pattern for GHB-0805DU-Y/O/R/R2