SE1A THRU SE1M SURFACE MOUNT HIGH EFFICIENCY RECTIFIER Reverse Voltage - 50 to 1000 Volts Forward Current - 1.0 Ampere Features For surface mounted applications Low profile package Built-in strain relief Easy pick and place Ultrafast recovery times for high efficiency Plastic package has Underwriters Laboratory Flammability classification 94V-0 High temperature soldering: 260 /10 seconds at terminals D IM E N S IO N S Mechanical Data in c h e s D IM A Case: SMA, molded plastic Terminals: Solder plated solderable per MIL-STD-750, method 2026 Polarity: Indicated by cathode band Weight: 0.004 ounce, 0.11 gram m m M in . M a x . M in . M a x . 0 .2 1 6 0 .2 2 6 5 .4 8 5 .7 4 B 0 .1 7 6 0 .1 8 2 4 .4 8 4 .6 3 C 0 .0 9 4 0 .1 0 0 2 .4 0 2 .5 5 D 0 .1 7 0 0 .1 7 6 4 .3 3 4 .4 8 E 0 .0 3 9 0 .0 5 5 1 .0 0 1 .4 0 F 0 .0 8 0 0 .0 8 1 2 .0 3 2 .0 7 G 0 .0 6 8 0 .0 8 3 1 .7 2 2 .1 0 H 0 .1 1 2 0 .1 1 8 2 .8 5 3 .0 0 J 0 .0 5 7 - 1 .4 4 - K - 0 .0 1 8 - 0 .4 5 L 0 .0 1 6 - 0 .4 0 N o te - M 0 .1 0 9 0 .1 1 5 2 .7 7 2 .9 3 N 0 .1 0 5 0 .1 0 7 2 .6 7 2 .7 3 P 0 .0 7 8 0 .0 8 1 2 .0 0 2 .0 5 Maximum Ratings and Electrical Characteristics Ratings at 25 ambient temperature unless otherwise specified. Resistive or inductive load. For capacitive load, derate current by 20%. Symbols SE1A SE1B SE1D SE1E SE1G SE1J SE1K SE1M Units Volts Maximum repetitive peak reverse voltage VRRM 50 100 200 300 400 600 800 1000 Maximum RMS voltage VRMS 35 70 140 210 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 300 400 600 800 1000 Volts Maximum average forward rectified current at TL=100 I(AV) 1.0 Amp Peak forward surge current 8.3mS single half sine-wave superimposed on rated load (MIL-STD-750D 4066 method) TA=55 IFSM 30.0 Amps Maximum instantaneous forward voltage at 1.0A VF Maximum DC reverse current at rated DC blocking voltage TA=25 TA=100 IR Trr Typical junction capacitance (Note 2) CJ Operating and storage temperature range 1.30 R 1.50 1.70 10.0 500.0 Maximum Reverse recovery time (Note 1) TJ=25 Maximum thermal resistance (Note 3) 1.00 50 JL TJ, TSTG 1 A 100 nS 15.0 F 30.0 /W -50 to +150 Notes: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, IRR=0.25A (2) Measured at 1.0MHz and applied reverse voltage of 4.0 volts (3) 8.0mm2 (0.013mm thick) land areas Volts RATINGS AND CHARACTERISTIC CURVES 2