SN1A THRU SN1M, SN13 SURFACE MOUNT GENERAL PURPOSE PLASTIC RECTIFIER Reverse Voltage - 50 to 1300 Volts Forward Current - 1.0 Ampere Features For surface mounted applications Low profile package Built-in strain relief Easy pick and place Plastic package has Underwriters Laboratory Flammability Classification 94V-0 High temperature soldering: 260 /10 seconds at terminals D IM E N S IO N S Mechanical Data in c h e s D IM A Case: SMA molded plastic Terminals: Solder plated, solderable per MIL-STD-750, method 2026 Polarity: Indicated by cathode band Weight: 0.004 ounce, 0.115 gram m m M in . M a x . M in . M a x . 0 .2 1 6 0 .2 2 6 5 .4 8 5 .7 4 B 0 .1 7 6 0 .1 8 2 4 .4 8 4 .6 3 C 0 .0 9 4 0 .1 0 0 2 .4 0 2 .5 5 D 0 .1 7 0 0 .1 7 6 4 .3 3 4 .4 8 E 0 .0 3 9 0 .0 5 5 1 .0 0 1 .4 0 F 0 .0 8 0 0 .0 8 1 2 .0 3 2 .0 7 G 0 .0 6 8 0 .0 8 3 1 .7 2 2 .1 0 H 0 .1 1 2 0 .1 1 8 2 .8 5 3 .0 0 J 0 .0 5 7 - 1 .4 4 - K - 0 .0 1 8 - 0 .4 5 L 0 .0 1 6 - 0 .4 0 N o te - M 0 .1 0 9 0 .1 1 5 2 .7 7 2 .9 3 N 0 .1 0 5 0 .1 0 7 2 .6 7 2 .7 3 P 0 .0 7 8 0 .0 8 1 2 .0 0 2 .0 5 Maximum Ratings and Electrical Characteristics Ratings at 25 ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Symbols SN1A SN1B SN1D SN1G SN1J SN1K SN1M SN13 Units Volts Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 1000 1300 Maximum RMS voltage VRMS 35 70 140 280 420 560 700 910 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 1300 Volts Maximum average forward rectified current at TL=100 I(AV) 1.0 Amp Peak forward surge current 8.3mS single half sine-wave superimposed on rated load (MIL-STD-750D 4066 method) IFSM 30.0 Amps Maximum instantaneous forward voltage at 1.0A VF 1.10 Volts IR 5.0 200.0 A S Maximum DC reverse current at rated DC blocking voltage TA=25 TA=125 Maximum reverse recovery time (Note 1) Trr 2.0 Typical junction capacitance (Note 2) CJ 15.0 F 30.0 /W Maximum thermal resistance (Note 3) Operating and storage temperature range R JL TJ, TSTG -55 to +150 Notes: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0MHz and applied reverse voltage of 4.0 volts (3) 8.0mm2 (0.013mm thick) land areas 1 RATINGS AND CHARACTERISTIC CURVES 2