SRN3 THRU SRN7 SURFACE MOUNT FAST SWITCHNG RECTIFIER Reverse Voltage - 50 to 600 Volts Forward Current - 1.0 Ampere Features For surface mounted applications Low profile package Built-in strain relief Easy pick and place Fast recovery times for high efficiency Plastic package has Underwriters Laboratory Flammability Classification 94V-0 High temperature soldering: 260 /10 seconds at terminals D IM E N S IO N S Mechanical Data D IM A Case: SMA molded plastic Terminals: Solder plated solderable per MIL-STD-750, method 2026 Polarity: Indicated by cathode band Weight: 0.004 ounce, 0.113 gram in c h e s m m M in . M a x . M in . M a x . 0 .2 1 6 0 .2 2 6 5 .4 8 5 .7 4 B 0 .1 7 6 0 .1 8 2 4 .4 8 4 .6 3 C 0 .0 9 4 0 .1 0 0 2 .4 0 2 .5 5 D 0 .1 7 0 0 .1 7 6 4 .3 3 4 .4 8 E 0 .0 3 9 0 .0 5 5 1 .0 0 1 .4 0 F 0 .0 8 0 0 .0 8 1 2 .0 3 2 .0 7 G 0 .0 6 8 0 .0 8 3 1 .7 2 2 .1 0 H 0 .1 1 2 0 .1 1 8 2 .8 5 3 .0 0 J 0 .0 5 7 - 1 .4 4 - K - 0 .0 1 8 - 0 .4 5 L 0 .0 1 6 - 0 .4 0 - M 0 .1 0 9 0 .1 1 5 2 .7 7 2 .9 3 N 0 .1 0 5 0 .1 0 7 2 .6 7 2 .7 3 P 0 .0 7 8 0 .0 8 1 2 .0 0 2 .0 5 Maximum Ratings and Electrical Characteristics Ratings at 25 ambient temperature unless otherwise specified. Resistive or inductive load. For capacitive load, derate current by 20%. Symbols SRN3 SRN4 SRN5 SRN6 SRN7 Units Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 Volts Maximum RMS voltage VRMS 35 70 140 280 420 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 Volts Maximum average forward rectified current at TL=90 I(AV) 1.0 Amp Peak forward surge current 8.3mS single half sine-wave superimposed on rated load (MIL-STD-750D 4066 method) IFSM 30.0 Amps Maximum instantaneous forward voltage at 1.0A VF 1.3 Volts IR 5.0 300.0 Maximum DC reverse current at rated DC blocking voltage TA=25 TA=125 Maximum reverse recovery time (Note 1) TJ=25 Trr Typical junction capacitance (Note 2) CJ Maximum thermal resistance (Note 3) Operating and storage temperature range R 150 JL TJ, TSTG 250 1 500 nS 10.0 F 30.0 /W -50 to +150 Notes: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0MHz and applied reverse voltage of 4.0 volts (3) 8.0mm2 (0.013mm thick) land areas A N o te RATINGS AND CHARACTERISTIC CURVES 2