HMC251MS8 v01.0801 MICROWAVE CORPORATION GaAs MMIC SMT DIVIDE-BY-2, 3.0 - 6.5 GHz FREQ. DIVIDER & DETECTORS - SMT 10 Typical Applications Features The HMC251MS8 is ideal for: Divide-By-Two • Wireless Local Loop Low Phase Noise: -130 dBc/Hz @ 10KHz • UNII & HiperLAN Single Positive Bias Voltage: +5.0V @ 27 mA • ISM Miniature Small Outline Pakcage: MSOP8 • VSAT Functional Diagram General Description The HMC251MS8 is a low noise divide-by-2 GaAs MMIC prescaler in an 8 lead surface mount MSOP plastic package. This device operates from 3.0 to 6.5 GHz (input frequency) with a single +5.0 V DC supply while drawing only 27 mA of current. The low residual phase noise of this prescaler helps the user maintain good system noise performance. Electrical Specifications, TA = +25° C, Vdd = +5.0V, 50 Ohm System Parameter Condition Min Typical Max Input Frequency Range 3.0 - 6.5 GHz Output Frequency Range 1.5 - 3.25 GHz Operating Input Power Range Fin = 3.0 - 4.0 GHz Fin = 4.0 - 5.0 GHz Fin = 5.0 - 6.0 GHz Fin = 6.0 - 6.5 GHz 6 -2 -8 -3 Output Power for Minimum Input Power Level (Note 1) Fin = 3.0 - 4.0 GHz Fin = 4.0 - 5.0 GHz Fin = 5.0 - 6.0 GHz Fin = 6.0 - 6.5 GHz -12 -14 -16 -17 Single-Side-Band Phase Noise Supply Current (Idd) -8.0 -7.7 -8.2 -8.5 Fin = 5.0 - 6.0 GHz Offset from carrier = 10KHz -130 Vdd = -5.0 Vdc 27 10 10 10 7 dBm dBm dBm dBm -3 -3 -3 -3 dBm dBm dBm dBm dBc/Hz 33 Note 1. Output Power Measured at half the Input Frequency. 10 - 2 Units For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com mA HMC251MS8 v01.0801 MICROWAVE CORPORATION GaAs MMIC SMT DIVIDE-BY-2, 3.0 - 6.5 GHz Output Power vs. Frequency @ Minimum Input Power Level Minimum Input Power vs. Input Frequency 20 OUTPUT POWER (dBm) -2 -40 C -4 +25 C -6 -8 -10 -12 10 Guaranteed Operating Window 0 -40 C -20 +25 C +85 C +85 C -14 -30 3 3.5 4 4.5 5 5.5 6 6.5 3 3.5 4 INPUT FREQUENCY (GHz) 4.5 5 5.5 6 6.5 INPUT FREQUENCY (GHz) Output Power for Input Power= +10 dBm* 0 OUTPUT POWER (dBm) 10 -10 Single-Side-Band Phase Noise vs. Offset from Carrier, fin= 5 to 6 GHz -80 -2 -90 -4 -100 -110 -6 -120 -8 -130 -10 -140 -12 -150 -14 -160 3 3.5 4 4.5 5 5.5 INPUT FREQUENCY (GHz) 6 6.5 10 1 10 2 10 3 10 4 10 OFFSET FROM CARRIER (Hz) 5 10 6 FREQ. DIVIDERS & DETECTORS - SMT MINIMUM INPUT POWER (dBm) 0 *Note: Output Power Measured @ fin/2 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 10 - 3 HMC251MS8 v01.0801 MICROWAVE CORPORATION GaAs MMIC SMT DIVIDE-BY-2, 3.0 - 6.5 GHz 0 0 -2 -2 Output Power @ 2.6 GHz -4 OUTPUT POWER (dBm) FREQ. DIVIDER & DETECTORS - SMT 10 OUTPUT POWER (dBm) Output Power vs. Input Power, Output Power vs. Input Power, MMIC PUMPED MIXER 17 - 25 InputGaAs Frequency= 5.2 SUB-HARMONICALLY GHz Input Frequency= 5.8 GHz -6 -8 -10 -12 -14 -16 Output Power @ 2.9 GHz -4 -6 -8 -10 -12 -14 -16 Feedthru Signal @ 5.2 GHz -18 Feedthru Signal @ 5.8 GHz -18 -20 -10 -5 0 5 10 15 20 -20 -10 -5 0 INPUT POWER (dBm) 5 10 15 RF OUT S-Parameters * j1 j1 3.0 GHz j2 j0.5 j2 3.25 GHz j0.2 j0.2 j5 j5 6.5 GHz 1.5 GHz 0 0.2 0.5 1 2 5 0 -j5 -j0.2 -j0.5 -j2 -j1 0.2 0.5 1 2 5 -j5 -j0.2 -j0.5 -j2 -j1 *S-Parameter Data is Available @ www.hittite.com 10 - 4 20 INPUT POWER (dBm) RF IN S-Parameters * j0.5 GHz For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com HMC251MS8 v01.0801 MICROWAVE CORPORATION GaAs MMIC SMT DIVIDE-BY-2, 3.0 - 6.5 GHz Vdd +8 Vdc Maximum Input Power (Vdd = +5.0 Vdc) 20 dBm Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C Application Circuit 10 Operating Notes: 1. With no input signal, or input signals below the minimum input power level, the prescaler will self-oscillate. 2. DC blocks on the RF ports are not required but are recommended if DC voltages exceeding 8 volts are present. Outline Drawing NOTES: 1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED PLASTIC SILICA AND SILICON IMPREGNATED. FREQ. DIVIDERS & DETECTORS - SMT Absolute Maximum Ratings 2. LEADFRAME MATERIAL: COPPER ALLOY 3. LEADFRAME PLATING: Sn/Pb SOLDER 4. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 5. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 6. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 7. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 10 - 5 v01.0801 MICROWAVE CORPORATION HMC251MS8 GaAs MMIC SMT DIVIDE-BY-2, 3.0 - 6.5 GHz Eval Board Layout (Top View) FREQ. DIVIDER & DETECTORS - SMT 10 List Of Materials Item Description J1, J2 PC Mount SMA Connector J3, J4 DC Pin C1, C2 330 pF capacitor, 0603 Pkg. U1 HMC251MS8 Prescaler PCB* 102285 Eval Board The circuit board used in the final application should be generated with proper RF circuit design techniques. Signal lines at RF IN and RF OUT should have 50 ohm impedance and the package ground leads should be connected directly to the ground plane similar to that shown. The evaluation circuit board shown is available from Hittite upon request. * Circuit Board Material: 4350 10 - 6 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v01.0801 MICROWAVE CORPORATION HMC251MS8 GaAs MMIC SMT DIVIDE-BY-2, 3.0 - 6.5 GHz Notes: FREQ. DIVIDERS & DETECTORS - SMT 10 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 10 - 7