TRS3237E 3-V TO 5.5-V MULTICHANNEL RS-232 1-MBit/s LINE DRIVER/RECEIVER www.ti.com SLLS796 – JUNE 2007 FEATURES • • • • • • • • Meets or Exceeds the Requirements of TIA/EIA-232-F and ITU v.28 Standards Operates With 3-V to 5.5-V VCC Supply Operates From 250 kbits/s to 1 Mbit/s Low Standby Current . . . 1 μA Typical External Capacitors . . . 4 × 0.1 μF Accepts 5-V Logic Input With 3.3-V Supply Designed to Be Interchangeable With Industry Standard '3237E Devices Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II • ESD Protection for RS-232 I/O Pins and Logic Input pins – ±15 kV – Human-Body Model (HBM) – ±8 kV – IEC61000-4-2, Contact Discharge – ±15 kV – IEC61000-4-2, Air-Gap Discharge APPLICATIONS • • • • • Battery-Powered, Hand-Held, and Portable Equipment PDAs and Palmtop PCs Notebooks, Sub-Notebooks, and Laptops Digital Cameras Mobile Phones and Wireless Devices 1 28 2 27 3 26 4 25 5 24 6 23 7 22 8 21 9 20 10 19 11 18 12 17 13 16 14 15 C1+ V+ VCC C1− DIN1 DIN2 DIN3 ROUT1 ROUT2 DIN4 ROUT3 DIN5 ROUT1B MBAUD 32 31 30 29 28 27 26 25 DOUT1 DOUT2 DOUT3 RIN1 RIN2 DOUT4 RIN3 N.C. 1 2 3 4 5 6 7 8 24 23 22 21 20 19 18 17 C1– DIN1 IN2 DIN3 ROUT1 ROUT2 DIN4 ROUT3 9 10 11 12 13 14 15 16 DOUT5 EN SHDN MBAUD N.C. ROUT1B DIN5 N.C. C2 + GND C2− V− DOUT1 DOUT2 DOUT3 RIN1 RIN2 DOUT4 RIN3 DOUT5 EN SHDN RHB PACKAGE (TOP VIEW) V− C2– GND C2+ C1+ V+ VCC N.C. DB, DW, OR PW PACKAGE (TOP VIEW) N.C.– Not internally connected DESCRIPTION/ORDERING INFORMATION The TRS3237E consists of five line drivers, three line receivers, and a dual charge-pump circuit with ±15-kV ESD protection pin to pin (serial-port connection pins, including GND). The device meets the requirements of TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controller and the serial-port connector. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-V supply. This device operates at data signaling rates of 250 kbit/s in normal operating mode (MBAUD = GND) and 1Mbit/s when MBAUD = VCC. The driver output slew rate is a maximum of 30 V/μs. The TRS3237E transmitters are disabled and the outputs are forced into high-impedance state when the device is in shutdown mode (SHDN = GND) and the supply current falls to less than 1 μA. Also, during shutdown, the onboard charge pump is disabled; V+ is lowered to VCC, and V– is raised toward GND. Receiver outputs also can be placed in the high-impedance state by setting enable (EN) high. ROUT1B remains active all the time, regardless of the EN and SHDN condition. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2007, Texas Instruments Incorporated TRS3237E 3-V TO 5.5-V MULTICHANNEL RS-232 1-MBit/s LINE DRIVER/RECEIVER www.ti.com SLLS796 – JUNE 2007 DESCRIPTION/ORDERING INFORMATION (CONTINUED) The TRS3237EC is characterized for operation from 0°C to 70°C. The TRS3237EI is characterized for operation from –40°C to 85°C. ORDERING INFORMATION TA 0°C to 70°C –40°C to 85°C (1) (2) PACKAGE (1) (2) ORDERABLE PART NUMBER SSOP – DB Reel of 2000 TRS3237ECDBR TRS3237EC SOIC – DW Reel of 2000 TRS3237ECDWR TRS3237EC TSSOP – PW Reel of 2000 TRS3237ECPWR RS37EC QFN – RHB Reel of 2000 TRS3237ECRHBR PREVIEW SSOP – DB Reel of 2000 TRS3237EIDBR TRS3237EI SOIC – DW Reel of 2000 TRS3237EIDWR TRS3237EI TSSOP – PW Reel of 2000 TRS3237EIPWR RS37EI QFN – RHB Reel of 2000 TRS3237EIRHBR PREVIEW Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. FUNCTION TABLE INPUTS SHDN (1) 2 TOP-SIDE MARKING OUTPUTS EN DOUT (1) ROUT ROUT1B 0 0 Z Active Active 0 1 Z (1) Z (1) Active 1 0 Active Active Active 1 1 Active Z (1) Active Z = high impedance (off) Submit Documentation Feedback TRS3237E 3-V TO 5.5-V MULTICHANNEL RS-232 1-MBit/s LINE DRIVER/RECEIVER www.ti.com SLLS796 – JUNE 2007 LOGIC DIAGRAM (POSITIVE LOGIC) DIN1 DIN2 DIN3 DIN4 DIN5 SHDN MBAUD ROUT1B ROUT1 ROUT2 ROUT3 EN 24 5 23 6 22 7 19 10 17 12 DOUT1 DOUT2 DOUT3 DOUT4 DOUT5 14 15 16 21 8 20 9 18 11 RIN1 RIN2 RIN3 13 Submit Documentation Feedback 3 TRS3237E 3-V TO 5.5-V MULTICHANNEL RS-232 1-MBit/s LINE DRIVER/RECEIVER www.ti.com SLLS796 – JUNE 2007 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX VCC Supply voltage range (2) –0.3 6 V V+ Positive-output supply voltage range (2) –0.3 7 V 0.3 –7 V 13 V V– Negative-output supply voltage range V+ – V– Supply voltage difference (2) VI Input voltage range VO Output voltage range (2) –0.3 6 Receiver –25 25 Driver Receiver Short-circuit duration θJA Driver (SHDN, MBAUD, EN) –13.2 13.2 –0.3 VCC + 0.3 DOUT to GND (1) (2) (3) V V Unlimited Package thermal impedance (3) Lead temperature 1,6 mm (1/16 in) from case for 10 s Tstg UNIT Storage temperature range –65 62 °C/W 260 °C 150 °C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect to network GND. The package thermal impedance is calculated in accordance with JESD 51-7. Recommended Operating Conditions (1) See Figure 5 VCC = 3.3 V Supply voltage VCC = 5 V VIH Driver and control high-level input voltage DIN, SHDN, MBAUD, EN VIL Driver and control low-level input voltage DIN, SHDN, MBAUD, EN VI Receiver input voltage TA Operating free-air temperature (1) VCC = 3.3 V VCC = 5 V TRS3237EC TRS3237EI MIN NOM MAX 3 3.3 3.6 4.5 5 5.5 2 5.5 2.4 5.5 UNIT V V 0 0.8 V –25 25 V 0 70 –40 85 °C Test conditions are C1–C4 = 0.1 μF at VCC = 3 V to 5 V. Electrical Characteristics (1) over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5) PARAMETER II Input leakage current ICC Supply current (TA = 25°C) TEST CONDITIONS DIN, SHDN, MBAUD, EN No load, SHDN = VCC (1) (2) 4 SHDN = GND Shutdown supply current SHDN = RIN = GND, DIN = GND or VCC Test conditions are C1–C4 = 0.1 μF at VCC = 3 V to 5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C. Submit Documentation Feedback MIN TYP (2) MAX 9 18 μA 0.5 2 mA 1 10 μA 10 300 nA UNIT TRS3237E 3-V TO 5.5-V MULTICHANNEL RS-232 1-MBit/s LINE DRIVER/RECEIVER www.ti.com SLLS796 – JUNE 2007 DRIVER SECTION xxx Electrical Characteristics (1) over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5) PARAMETER MIN TYP (2) TEST CONDITIONS VOH High-level output voltage DOUT at RL = 3 kΩ to GND, DIN = GND 5 5.4 VOL Low-level output voltage DOUT at RL = 3 kΩ to GND, DIN = VCC –5 –5.4 IIH High-level input current VI = VCC IIL Low-level input current VI at GND IOS Short-circuit output current (3) VCC = 3.6 V or 3.3 V, VO = 0 V ro Output resistance VCC, V+, and V– = 0 V, VO = ±2 V (1) (2) (3) ±0.01 ±0.01 300 MAX UNIT V V ±1 μA ±1 μA ±60 mA Ω 50k Test conditions are C1–C4 = 0.1 μF at VCC = 3 V to 5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C. Short-circuit durations should be controlled to prevent exceeding the device absolute power-dissipation ratings, and not more than one output should be shorted at a time. Switching Characteristics (1) over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5) PARAMETER TEST CONDITIONS MIN CL = 1000 pF, MBAUD = GND Maximum data rate CL = 1000 pF, VCC = 4.5 V to 5.5 V, MBAUD = VCC MAX UNIT 250 RL = 3 kΩ, 1 DIN switching, See Figure 1 CL = 250 pF, VCC = 3 V to 4.5 V, MBAUD = VCC 1000 kbit/s 1000 tsk(p) Pulse skew (3) CL = 150 pF to 2500 pF, RL = 3 kΩ to 7 kΩ, MBAUD = VCC or GND, See Figure 2 SR(tr) Slew rate, transition region (see Figure 1) VCC = 3.3 V, RL = 3 kΩ to 7 kΩ, TA = 25°C (1) (2) (3) TYP (2) CL = 150 pF to 1000 pF CL = 150 pF to 2500 pF, 100 ns MBAUD = GND 6 30 MBAUD = VCC 24 150 MBAUD = GND 4 30 V/μs Test conditions are C1–C4 = 0.1 μF at VCC = 3 V to 5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C. Pulse skew is defined as |tPLH – tPHL| of each channel of the same device. Submit Documentation Feedback 5 TRS3237E 3-V TO 5.5-V MULTICHANNEL RS-232 1-MBit/s LINE DRIVER/RECEIVER www.ti.com SLLS796 – JUNE 2007 RECEIVER SECTION xxx Electrical Characteristics (1) over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5) PARAMETER VOH High-level output voltage IOH = –1 mA VOL Low-level output voltage IOL = 1 mA TYP (2) VCC – 0.6 VCC – 0.1 MAX VCC = 3.3 V Positive-going input threshold voltage VIT– Negative-going input threshold voltage Vhys Input hysteresis (VIT+ – VIT–) Ioz Output leakage current EN = VCC ri Input resistance VI = ±3 V to ±25 V 1.5 2.4 2 2.4 VCC = 5 V VCC = 3.3 V 0.6 1.1 VCC = 5 V 0.8 1.5 UNIT V 0.4 VIT+ (1) (2) MIN TEST CONDITIONS V V V 0.5 V ±0.05 ±10 μA 5 7 kΩ 3 Test conditions are C1–C4 = 0.1 mF at VCC = 3 V to.5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C. Switching Characteristics (1) over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) PARAMETER TEST CONDITIONS TYP (2) UNIT tPLH Propagation delay time, low- to high-level output CL = 150 pF, See Figure 3 150 tPHL Propagation delay time, high- to low-level output CL = 150 pF, See Figure 3 150 ns ten Output enable time CL = 150 pF, RL = 3 kΩ, See Figure 4 2.6 μs tdis Output disable time CL = 150 pF, RL = 3 kΩ, See Figure 4 2.4 μs tsk(p) Pulse skew (3) See Figure 3 50 ns TYP UNIT (1) (2) (3) ns Test conditions are C1–C4 = 0.1 μF at VCC = 3 V to 5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C. Pulse skew is defined as |tPLH – tPHL| of each channel of the same device. ESD Protection PIN TEST CONDITIONS ±15 HBM DIN, RIN, ROUT 6 IEC61000-4-2, Contact Discharge ±8 IEC61000-4-2, Air-Gap Discharge ±15 Submit Documentation Feedback kV TRS3237E 3-V TO 5.5-V MULTICHANNEL RS-232 1-MBit/s LINE DRIVER/RECEIVER www.ti.com SLLS796 – JUNE 2007 PARAMETER MEASUREMENT INFORMATION 3V Generator (see Note B) Input RS-232 Output 50 Ω RL tTHL CL (see Note A) 3V SHDN = VCC TEST CIRCUIT 0V 3V 3V Output SR(tr) + tTLH −3 V −3 V 6V t THL or tTLH VOH VOL VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns. Figure 1. Driver Slew Rate 3V Generator (see Note B) RS-232 Output 50 Ω RL Input 1.5 V 1.5 V 0V CL (see Note A) tPHL tPLH VOH 3V SHDN = VCC 50% 50% Output VOL TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns. Figure 2. Driver Pulse Skew 3 V or 0 V EN = GND 3V Input 1.5 V 1.5 V −3 V Output Generator (see Note B) tPHL 50 Ω 3V EN = GND tPLH CL (see Note A) VOH 50% Output 50% VOL TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns. Figure 3. Receiver Propagation Delay Times Submit Documentation Feedback 7 TRS3237E 3-V TO 5.5-V MULTICHANNEL RS-232 1-MBit/s LINE DRIVER/RECEIVER www.ti.com SLLS796 – JUNE 2007 PARAMETER MEASUREMENT INFORMATION (continued) 3V Input VCC 3 V or 0 V 1.5 V GND S1 −3 V tPZH (S1 at GND) tPHZ (S1 at GND) RL 3 V or 0 V 1.5 V VOH Output 50% Output CL (see Note A) EN Generator (see Note B) 50 Ω 0.3 V tPLZ (S1 at VCC) tPZL (S1 at VCC) 0.3 V Output 50% VOL TEST CIRCUIT NOTES: A. B. C. D. VOLTAGE WAVEFORMS CL includes probe and jig capacitance. The pulse generator has the following characteristics: ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns. tPLZ and tPHZ are the same as tdis. tPZL and tPZH are the same as ten. Figure 4. Receiver Enable and Disable Times 8 Submit Documentation Feedback TRS3237E 3-V TO 5.5-V MULTICHANNEL RS-232 1-MBit/s LINE DRIVER/RECEIVER www.ti.com SLLS796 – JUNE 2007 APPLICATION INFORMATION CBYPASS = 0.1 µF + − 1 2 + C2 V+ 28 27 + GND C3† − − 3 4 − + C1+ C2+ C2− VCC V− C1− C4 DOUT1 DOUT2 DOUT3 RIN1 + − 26 C1 25 5 24 6 23 7 22 8 21 DIN1 DIN2 DIN3 ROUT1 5 kΩ RS-232 Port RIN2 9 20 ROUT2 Logic I/Os 5 kΩ DOUT4 RIN3 10 19 11 18 DIN4 ROUT3 5 kΩ DOUT5 12 17 16 EN SHDN 13 14 15 DIN5 ROUT1B MBAUD † C3 can be connected to VCC or GND. NOTES: A. Resistor values shown are nominal. B. Nonpolarized ceramic capacitors are acceptable. If polarized tantalum or electrolytic capacitors are used, they should be connected as shown. VCC vs CAPACITOR VALUES VCC 3.3 V ± 0.15 V 3.3 V ± 0.3 V 5 V ± 0.5 V 3 V to 5.5 V C1 0.1 µF 0.22 µF 0.047 µF 0.22 µF C2, C3, and C4 0.1 µF 0.22 µF 0.33 µF 1 µF Figure 5. Typical Operating Circuit and Capacitor Values Submit Documentation Feedback 9 PACKAGE OPTION ADDENDUM www.ti.com 26-Sep-2007 PACKAGING INFORMATION (1) Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TRS3237ECDB ACTIVE SSOP DB 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237ECDBG4 ACTIVE SSOP DB 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237ECDBR ACTIVE SSOP DB 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237ECDBRG4 ACTIVE SSOP DB 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237ECDW ACTIVE SOIC DW 28 20 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237ECDWG4 ACTIVE SOIC DW 28 20 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237ECDWR ACTIVE SOIC DW 28 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237ECDWRG4 ACTIVE SOIC DW 28 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237ECPW ACTIVE TSSOP PW 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237ECPWG4 ACTIVE TSSOP PW 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237ECPWR ACTIVE TSSOP PW 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237ECPWRG4 ACTIVE TSSOP PW 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237EIDB ACTIVE SSOP DB 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237EIDBG4 ACTIVE SSOP DB 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237EIDBR ACTIVE SSOP DB 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237EIDBRG4 ACTIVE SSOP DB 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237EIDW ACTIVE SOIC DW 28 20 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237EIDWG4 ACTIVE SOIC DW 28 20 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237EIDWR ACTIVE SOIC DW 28 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237EIDWRG4 ACTIVE SOIC DW 28 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237EIPW ACTIVE TSSOP PW 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237EIPWG4 ACTIVE TSSOP PW 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237EIPWR ACTIVE TSSOP PW 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3237EIPWRG4 ACTIVE TSSOP PW 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM The marketing status values are defined as follows: Addendum-Page 1 Lead/Ball Finish MSL Peak Temp (3) PACKAGE OPTION ADDENDUM www.ti.com 26-Sep-2007 ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 4-Oct-2007 TAPE AND REEL BOX INFORMATION Device Package Pins Site Reel Diameter (mm) Reel Width (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TRS3237ECDBR DB 28 SITE 41 330 16 8.2 10.5 2.5 12 16 Q1 TRS3237ECDWR DW 28 SITE 60 330 32 11.35 18.67 3.1 16 32 Q1 TRS3237EIDBR DB 28 SITE 41 330 16 8.2 10.5 2.5 12 16 Q1 TRS3237EIDWR DW 28 SITE 60 330 32 11.35 18.67 3.1 16 32 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com Device 4-Oct-2007 Package Pins Site Length (mm) Width (mm) Height (mm) TRS3237ECDBR DB 28 SITE 41 346.0 346.0 33.0 TRS3237ECDWR DW 28 SITE 60 346.0 346.0 49.0 TRS3237EIDBR DB 28 SITE 41 346.0 346.0 33.0 TRS3237EIDWR DW 28 SITE 60 346.0 346.0 49.0 Pack Materials-Page 2 MECHANICAL DATA MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0°–ā8° 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0°– 8° A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Telephony www.ti.com/telephony Low Power Wireless www.ti.com/lpw Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated