LUMIMICRO – FLASH LED SPECIFICATION FLASH WHITE LED Super Luminosity White LED MODEL: LMFLSP100 Customer Model Issued Date Checked By Approved By Description Written By LMFLSP100 2003 – 11 - 20 Chip Type White LED Checked By Lumimicro Co., Ltd 362-43 Woncheon-dong,Yeongtonggu,, Suwon-si, Gyeonggi-do, Korea Date: 2005-06-10, Tel:+82-31-213-9200, Fax: +8231-213-9210 LUMIMICRO CO., LTD Approved by 1/9 ◆ Features [1] Built-in 3chip Super-luminosity Chip LED [2] Built-in zener Diode- Flash LED [3] Super-luminosity chip LED [4] Blue LED + Organic - Inorganic Phosphore [5] Using a package with high heat dissipation properties, it can be driven with a large current 3 LED Chip Die + 3 Port Zener Diode [6] Wide viewing angle [7] External dimensions: 5.0 x 5.0 x 1.5t mm Model: LMFLSP100 [8] Lead frame package with individual 6 pin ◆ Applications [1] Camera Flash [2] Hand Carrier Flash ◆ Outline Dimensions Unit: mm, Tolerance: ± 0.1 LUMIMICRO CO., LTD 2/9 ◆ Absolute Maximum Ratings. Parameter Symbol Rating Value Unit Power Dissipation PD 300 mW Forward Current IF 90 mA Forward Pulse Current IPF 180 mA Reverse Voltage VR 5 V Operating Temperature TOT -30 to +85 ℃ Storage Temperature TST -40 to +100 ℃ Soldering Temperature TSD Reflow: 240℃ for 10sec ℃ Hand Soldering: 350℃ for 10sec * Duty ratio=1/10, Pulse width < 30ms. ◆ Electro-optical Spec. Parameter Symbol Condition Min Typ. Max Unit Forward Voltage 1 VF 1 IF=20m A/each chip - 3.4 3.8 V Forward Voltage 2 VF 2 IF=10uA 1.8 _ _ V Luminous Intensity IV IF=20mA/ each chip 2.5 4.0 _ cd The tolerance of Intensity measurement: ± 10%, The tolerance of VF measurement: ±0.1V ◆ C.I.E x 0.290 0.290 0.330 0.330 y 0.276 0.320 0.318 0.365 Green Red Blue - The uncertainty of the C.I.E coordinates measurement: ±0.01 LUMIMICRO CO., LTD 3/9 ◆ FLASH LED-LMFLSP100 - Optical & Electrical Characteristics Ta = 25°C IF = 20mA/Chip Ta = 25°C IF = 20mA/Chip Spectrum Graph Allowable Current per Chip z VF : Forward Voltage(V), IF : Forward Current(m A), Ta : Ambient Temperature(°C) LUMIMICRO CO., LTD 4/9 ◆ Directivity (LMFLSP100) (LMFLSP100) (LMFLSP100) LUMIMICRO CO., LTD 5/9 ◆ Reliability Results LUMIMICRO CO., LTD 6/9 ◆ Precautions For Use This device should not be used in any type of fluid such as water, oil, organic solvent, etc. When washing is required, IPA should be used. When the LEDs are illuminating, operating current should be decided after considering the ambient maximum temperature. LEDs must be stored to maintain a clean atmosphere. If the LEDs are stored for 3months or more after being shipped from LUMIMICRO, sealed container with a nitrogen atmosphere should be used for storage. The LEDs must be dip soldered within seven days after opening the moisture-proof packing. Repack unused Products with anti-moisture packing, fold to close any opening and then store in dry place. The appearance and specifications of the product may be modified for improvement without notice. These LEDs are sensitive to the static electricity and surge. It is recommended to use a wrist band or anti-electrostatic glove when handling the LEDs. If Over voltage which exceeds the absolute maximum rating is applied to LEDs, it will cause damage in LEDs and result in destruction. Damaged LEDs will show some unusual characteristics such as remarkably increased leak current, turn-on voltage becomes lower and the LEDs get unlighted at low current. ◆ Soldering Condition Dip Max 260C Temp.(℃) Max 150C Pre-heating 120max 120sec. ① Solder Dip Conditions The Immersion of leads into a solder bath @MAX260℃ shall be to 5 seconds max. 5sec. 30sec. RT Time Max 240C Temp.(℃) Max 150C ② Reflow Conditions Preliminary heating to be at 150 ℃ max. for 2 minutes max. Soldering heat to be at 240℃ max. for 5 seconds max. 5sec. 120sec Time ③ For Manual Soldering Not more than 5 seconds @MAX300℃, under Soldering iron. LUMIMICRO CO., LTD 7/9 ◆ Recommended Soldering Pad Size ◆ Taping pocket Dimension LUMIMICRO CO., LTD 8/9 ◆ Reel Dimensions Φ 178 Φ 25 Φ 21.4 Φ 13.5 13.5 φ 60φ 2.4 13 15 L U MI MI C R O One Reel Max 750EA Unit MODEL : LMFLC2500 RANK : L1-C2 DATE : QNT : 2004-03-27 3,000 EA : ********* Tolerance ±0.1 mm Lumi-No ***** LUMI MICRO LUMIMICRO FLASH LED SIDE VIEW LED - Aluminum Bag Aluminum Bag - Box Spec. Reel in a Bag Silica in a Bag Goods QNT in a Bag 1 Reel 1 Silica Max : 750ea Dimensions (Width/Thickness) Unit:mm Box-L1 275/ 285/ 50 Reels in Box Goods QNT in Box 10 Max : 7,500ea LUMIMICRO CO., LTD 9/9 ◆ Label Spec. Model Name Shipping Date ***** Taping Quantity Lumimicro-Lot Number ◆ Weight: 65.1 mg (Measurement Tolerance: ± 10 %) LUMIMICRO CO., LTD