Electrical / Environmental High Current Low Profile Surface Mount Inductors Sfor RCoompH t n a li ls • • • • ode ‘LF’ M Operating Temperature Range Temperature Rise, Maximum Ambient Temperature, Maximum Insulation System -40°C to +125°C 40°C 80°C Class F, 155°C Specifications Inductance 100kHz, 0.1V @ 0 Adc @ Irated (nH±20%) (nH) Typ. Min. Typ. Part Number HM69-10R025 HM69-20R050 HM69-30R070 HM69-40R10 HM69-50R10 HM69-50R15 HM69-55R10 HM69-55R20 HM69-60R10 HM69-60R15 HM69-60R20 HM69-70R30 HM69-75R20 HM69-80R30 Notes: 25 50 70 100 100 150 100 200 100 150 200 300 200 300 18 28 50 60 72 96 64 140 69 104 144 200 150 216 (1) Typ. Max. Irated @ 25°C (Adc) 0.27 0.20 0.40 0.31 0.40 0.40 0.45 0.45 0.42 0.42 0.42 0.17 0.40 0.17 0.33 0.24 0.48 0.39 0.48 0.48 0.56 0.56 0.50 0.50 0.50 0.20 0.50 0.25 42 70 46 28 29 18 45 21 68 48 31 37 20 40 DCR (mΩ) 25 36 67 75 95 120 80 175 87 130 180 250 175 285 (2) Heating (3) Current (A) Core Loss Factor 22 35 25 25 24 24 25 25 31 31 31 70 40 76 (4) K1 K2 3.847E-14 1.074E-13 1.074E-13 7.124E-14 8.733E-14 8.733E-14 1.337E-13 1.337E-13 2.311E-13 2.311E-13 2.311E-13 6.784E-13 3.559E-13 9.107E-13 59.444 50.117 70.164 156.891 127.990 191.986 96.541 160.902 52.336 78.503 104.671 98.921 134.203 72.674 (1) DC resistance is measured at 25°C. (2) The rated current (Irated) is the current at which the inductance will be decreased by 20% from its initial (zero DC) value. (3) The heating current is the DC current, which causes the component temperature to increase by approximately 40°C. This current is determined by soldering the component on a typical application PCB, and then apply the device for 30 minutes. (4) Core Loss approximation is based on published core data: Core Loss = K1 * (f)1.77 * (K2∆I)2.21 Where: core loss in watt f = switching frequency in kHz K1 and K2 = core loss factor ∆I = delta I across the component in Amp. K2∆I = one half of the peak to peak flux density across the component in Gauss Packaging Standard: Embossed Tape & Reel Reel: Diameter: Capacity: Case size 10,40 Case size 20,30,60 Case size 50,55,75 Case size 70,80 = = = = = 13” (330.2mm) 1000 Units 800 Units 500 Units 350 Units Ordering Information Model Series Case Size HM69 50 R10 LF TR Inductance Code: First 2 digits are significant. Last digit denotes the number of trailing zeros. For values below 10µH, “R” denotes the decimal point. 40 Tape & Reel Packing Lead-Free Option LF = Lead-Free (No code used for non lead-free part) MAGNETIC COMPONENTS SELECTOR GUIDE 2006 EDITION We reserve the right to change specifications without prior notice. www.bitechnologies.com Outline Dimensions (mm) Top View Bottom View Recommended Solder Pad Layout Electrical Characteristics @ 25°C 2006 EDITION MAGNETIC COMPONENTS SELECTOR GUIDE www.bitechnologies.com We reserve the right to change specifications without prior notice 41 Electrical Characteristics @ 25°C (Cont’d) 42 MAGNETIC COMPONENTS SELECTOR GUIDE 2006 EDITION We reserve the right to change specifications without prior notice. www.bitechnologies.com