SN54ABT16245A, SN74ABT16245A 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS www.ti.com FEATURES • • • • • • • • • • Members of the Texas Instruments Widebus™ Family State-of-the-Art EPIC-IIB™ BiCMOS Design Significantly Reduces Power Dissipation Typical VOLP (Output Ground Bounce) <1 V at VCC = 5 V, TA = 25°C High-Impedance State During Power Up and Power Down Distributed VCC and GND Pin Configuration Minimizes High-Speed Switching Noise Flow-Through Architecture Optimizes PCB Layout High-Drive Outputs (–32-mA IOH, 64-mA IOL) Latch-Up Performance Exceeds 500 mA Per JESD 70 ESD Protection Exceeds 2000 V Per MIL-STD-883, Method 3015; Exceeds 200 V Using Machine Model (C = 200 pF, R = 0) Package Options Includes Plastic Thin Very Small-Outline (DGV), Shrink Small-Outline (DL), and Thin Shrink Small-Outline (DGG) Packages and 380-mil Fine-Pitch Ceramic (WD) Flat Package Using 25-mil Center-to-Center Spacings SCBS300G – MARCH 1994 – REVISED JANUARY 2006 SN54ABT16245A . . . WD PACKAGE SN74ABT16245A . . . DGG, DGV, OR DL PACKAGE (TOP VIEW) 1DIR 1B1 1B2 GND 1B3 1B4 VCC 1B5 1B6 GND 1B7 1B8 2B1 2B2 GND 2B3 2B4 VCC 2B5 2B6 GND 2B7 2B8 2DIR 1 48 2 47 3 46 4 45 5 44 6 43 7 42 8 41 9 40 10 39 11 38 12 37 13 36 14 35 15 34 16 33 17 32 18 31 19 30 20 29 21 28 22 27 23 26 24 25 1OE 1A1 1A2 GND 1A3 1A4 VCC 1A5 1A6 GND 1A7 1A8 2A1 2A2 GND 2A3 2A4 VCC 2A5 2A6 GND 2A7 2A8 2OE DESCRIPTION The 'ABT16245A devices are 16-bit noninverting 3-state transceivers designed for synchronous two-way communication between data buses. The control-function implementation minimizes external timing requirements. These devices can be used as two 8-bit transceviers or one 16-bit transceiver. They allow data transmission from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction-control (DIR) input. The output-enable (OE) input can be used to disable the device so that the buses are effectively isolated. When VCC is between 0 and 2.1 V, the device is in the high-impedance state during power up or power down. However, to ensure the high-impendance state above 2.1 V, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. The SN54ABT16245A is characterized for operation over the full military temperature range of –55°C to 125°C. The SN74ABT16245A is characterized for operation from –40°C to 85°C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus, EPIC-IIB are trademarks of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 1994–2006, Texas Instruments Incorporated On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters. SN54ABT16245A, SN74ABT16245A 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS www.ti.com SCBS300G – MARCH 1994 – REVISED JANUARY 2006 FUNCTION TABLE (EACH 8-BIT SECTION) INPUTS OE OPERATION DIR L L B data to A bus L H A data to B bus H X Isolation LOGIC SYMBOL(1) 48 1OE 1DIR 1 G3 3 EN1 [BA] 3 EN2 [AB] 25 2OE 2DIR 24 G6 6 EN4 [BA] 6 EN5 [AB] 1A1 47 2 1 1B1 2 1A2 1A3 1A4 1A5 1A6 1A7 1A8 2A1 46 3 44 5 43 6 41 8 40 9 38 11 37 12 36 13 4 1B2 1B3 1B4 1B5 1B6 1B7 1B8 2B1 5 2A2 2A3 2A4 2A5 2A6 2A7 2A8 (1) 2 35 14 33 16 32 17 30 19 29 20 27 22 26 23 2B2 2B3 2B4 2B5 2B6 2B7 2B8 This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. SN54ABT16245A, SN74ABT16245A 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS www.ti.com SCBS300G – MARCH 1994 – REVISED JANUARY 2006 LOGIC DIAGRAM (POSITIVE LOGIC) 1DIR 1 2DIR 48 1A1 25 1OE 47 2A1 2 24 2OE 36 13 1B1 2B1 To Seven Other Channels To Seven Other Channels Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX VCC Supply voltage range –0.5 7 V VI Input voltage range (except I/O ports) (2) –0.5 7 V VO Voltage range applied to any output in the high or power-off state –0.5 5.5 V IO Current into any output in the low state IIK IOK SN54ABT16245A 96 SN74ABT16245A 128 Input clamp current VI < 0 –18 mA Output clamp current VO < 0 –50 mA θJA Package thermal impedance (3) Tstg Storage temperature range DGG package 89 DGV package 93 DL package (1) (2) (3) UNIT mA °C/W 94 –65 150 °C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. The package thermal impedance is calculated in accordance with JESD 51. 3 SN54ABT16245A, SN74ABT16245A 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS www.ti.com SCBS300G – MARCH 1994 – REVISED JANUARY 2006 Recommended Operating Conditions (1) SN54ABT16245A SN74ABT16245A VCC Supply voltage VIH High-level input voltage VIL Low-level input voltage VI Input voltage IOH High-level output current IOL Low-level output current ∆t/∆v Input transition rise or fall rate MIN MAX MIN MAX 4.5 5.5 4.5 5.5 2 0.8 0 Outputs enabled ∆t/∆VCC Power-up ramp rate 200 TA –55 (1) 4 Operating free-air temperature 2 VCC V V 0.8 0 UNIT V VCC V –24 –32 mA 48 64 mA 10 10 ns/V µs/V 200 125 –40 85 All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. °C SN54ABT16245A, SN74ABT16245A 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS www.ti.com SCBS300G – MARCH 1994 – REVISED JANUARY 2006 Electrical Characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK VOH TEST CONDITIONS SN54ABT16245A SN74ABT16245A MAX MIN MIN II = –18 mA VCC = 4.5 V, IOH = –3 mA 2.5 2.5 2.5 VCC = 5 V, IOH = –3 mA 3 3 3 IOH = –24 mA 2 2 IOH = –32 mA 2 (2) VCC = 4.5 V –1.2 MAX VCC = 4.5 V, VCC = 4.5 V VOL TA = 25°C MIN TYP (1) –1.2 0.55 IOL = 64 mA 0.55 (2) VCC = 0 to 5.5 V, VI = VCC or GND A or B port V V 0.55 0.55 100 Control inputs UNIT 2 IOL = 48 mA Vhys –1.2 MAX V mV ±1 ±1 ±1 VCC = 2.1 V to 5.5 V, VI = VCC or GND ±20 (2) ±100 ±20 IOZPU VCC = 0 to 2.1 V, VO = 0.5 V to 2.7 V, OE = X ±50 (3) ±50 (3) ±50 µA IOZPD VCC = 2.1 V to 0, VO = 0.5 V to 2.7 V, OE = X ±50 (3) ±50 (3) ±50 µA 10 10 (5) µA –10 –10 (5) µA ±100 µA 50 µA –180 mA II µA (4) VCC = 2.1 V to 5.5 V, VO = 2.7 V, OE ≥ 2 V 10 (5) IOZL (4) VCC = 2.1 V to 5.5 V, VO = 0.5 V, OE ≥ 2 V –10 (5) Ioff VCC = 0, VI or VO ≤ 5.5 V ICEX VCC = 5.5 V, VO = 5.5 V Outputs high (6) VCC = 5.5 V, VO = 2.5 V IOZH IO A or B port ICC VCC = 5.5 V, IO = 0, VI = VCC or GND ±100 50 –50 –100 –180 50 –50 –180 –50 Outputs high 2 2 2 Outputs low 32 32 32 Outputs disabled 2 2 2 Outputs enabled 2 1.5 2 Outputs disabled 0.05 1 0.05 1.5 1.5 1.5 mA Data inputs VCC = 5.5 V, One inputs at 3.4 V, Other inputs at VCC or GND Control inputs VCC = 5.5 V, One input at 3.4 V, Other inputs at VCC or GND Ci Control inputs VI = 2.5 V or 0.5 V 3 pF Co A or B port VO = 2.5 V or 0.5 V 6 pF ∆ICC (7) (1) (2) (3) (4) (5) (6) (7) mA All typical values are at VCC = 5 V. On products compliant to MIL-PRF-38535, this parameter does not apply. On products compliant to MIL-PRF-38535, this parameter is not production tested. The parameters IOZH and IOZL include the input leakage current. This limit may vary among suppliers. Not more than one output should be tested at a time, and the duration of the test should not exceed one second. This is the increase in supply current for each input that is at the specified TTL voltage level, rather than VCC or GND. 5 SN54ABT16245A, SN74ABT16245A 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS www.ti.com SCBS300G – MARCH 1994 – REVISED JANUARY 2006 Switching Characteristics over recommended operating ranges of supply voltage and operating free-air temperature, CL = 50 pF (unless otherwise noted) (see Figure 1 ) SN54ABT16245A PARAMETER tPLH tPHL tPZH tPZL tPHZ tPLZ FROM (INPUT) TO (OUTPUT) A or B B or A OE B or A OE B or A VCC = 5 V, TA = 25°C MIN MAX MIN TYP MAX 0.5 2.2 3.4 0.5 4 0.5 2.3 3.8 0.5 4.6 0.8 3.6 5.2 0.8 5.5 0.9 3.7 6.1 0.1 7.3 1.3 4.4 5.8 1.3 6.3 1.4 3.3 4.7 1.4 5.5 UNIT ns ns ns Switching Characteristics over recommended operating ranges of supply voltage and operating free-air temperature, CL = 50 pF (unless otherwise noted) (see Figure 1 ) SN74ABT16245A PARAMETER tPLH tPHL tPZH tPZL tPHZ tPLZ 6 FROM (INPUT) TO (OUTPUT) A or B B or A OE B or A OE B or A VCC = 5 V, TA = 25°C MIN MAX MIN TYP MAX 1 2.2 3.4 1 3.9 1 2.3 3.7 1 4.2 1 3.6 5.2 1 6.3 1 3.7 5.4 1 6.4 2 4.4 5.8 2 6.3 1.5 3.3 4.7 1.5 5.2 UNIT ns ns ns SN54ABT16245A, SN74ABT16245A 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS www.ti.com SCBS300G – MARCH 1994 – REVISED JANUARY 2006 PARAMETER MEASUREMENT INFORMATION 500 Ω From Output Under Test S1 7V Open GND CL = 50 pF (see Note A) 500 Ω TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 7V Open 3V LOAD CIRCUIT Timing Input 1.5 V 0V tw tsu 3V th 3V Input 1.5 V 1.5 V 1.5 V Data Input 1.5 V 0V 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VOLTAGE WAVEFORMS PULSE DURATION 3V 1.5 V Input 1.5 V 0V tPLH tPHL 1.5 V 1.5 V VOL tPHL 1.5 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS tPLZ 3.5 V 1.5 V Output Waveform 2 S1 at Open (see Note B) VOL + 0.3 V VOL tPHZ tPZH 1.5 V 1.5 V 0V Output Waveform 1 S1 at 7 V (see Note B) tPLH VOH Output 1.5 V tPZL VOH Output 3V Output Control 1.5 V VOH − 0.3 V VOH ≈0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time, with one transition per measurement. Figure 1. Load Circuit and Voltage Waveforms 7 PACKAGE OPTION ADDENDUM www.ti.com 18-Jul-2006 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty 1 5962-9317501MXA ACTIVE CFP WD 48 ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74ABT16245ADGVRE4 ACTIVE TVSOP DGV 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT16245ADGGR ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT16245ADGVR ACTIVE TVSOP DGV 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT16245ADL ACTIVE SSOP DL 48 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT16245ADLG4 ACTIVE SSOP DL 48 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT16245ADLR ACTIVE SSOP DL 48 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT16245ADLRG4 ACTIVE SSOP DL 48 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SNJ54ABT16245AWD ACTIVE CFP WD 48 TBD A42 SNPB MSL Peak Temp (3) 74ABT16245ADGGRG4 1 TBD Lead/Ball Finish A42 SNPB N / A for Pkg Type N / A for Pkg Type (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 MECHANICAL DATA MCFP010B – JANUARY 1995 – REVISED NOVEMBER 1997 WD (R-GDFP-F**) CERAMIC DUAL FLATPACK 48 LEADS SHOWN 0.120 (3,05) 0.075 (1,91) 0.009 (0,23) 0.004 (0,10) 1.130 (28,70) 0.870 (22,10) 0.370 (9,40) 0.250 (6,35) 0.390 (9,91) 0.370 (9,40) 0.370 (9,40) 0.250 (6,35) 48 1 0.025 (0,635) A 0.014 (0,36) 0.008 (0,20) 25 24 NO. OF LEADS** 48 56 A MAX 0.640 (16,26) 0.740 (18,80) A MIN 0.610 (15,49) 0.710 (18,03) 4040176 / D 10/97 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification only Falls within MIL STD 1835: GDFP1-F48 and JEDEC MO -146AA GDFP1-F56 and JEDEC MO -146AB POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000 DGV (R-PDSO-G**) PLASTIC SMALL-OUTLINE 24 PINS SHOWN 0,40 0,23 0,13 24 13 0,07 M 0,16 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 0°–8° 1 0,75 0,50 12 A Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,08 14 16 20 24 38 48 56 A MAX 3,70 3,70 5,10 5,10 7,90 9,80 11,40 A MIN 3,50 3,50 4,90 4,90 7,70 9,60 11,20 DIM 4073251/E 08/00 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side. Falls within JEDEC: 24/48 Pins – MO-153 14/16/20/56 Pins – MO-194 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MSSO001C – JANUARY 1995 – REVISED DECEMBER 2001 DL (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 48 PINS SHOWN 0.025 (0,635) 0.0135 (0,343) 0.008 (0,203) 48 0.005 (0,13) M 25 0.010 (0,25) 0.005 (0,13) 0.299 (7,59) 0.291 (7,39) 0.420 (10,67) 0.395 (10,03) Gage Plane 0.010 (0,25) 1 0°–ā8° 24 0.040 (1,02) A 0.020 (0,51) Seating Plane 0.110 (2,79) MAX 0.004 (0,10) 0.008 (0,20) MIN PINS ** 28 48 56 A MAX 0.380 (9,65) 0.630 (16,00) 0.730 (18,54) A MIN 0.370 (9,40) 0.620 (15,75) 0.720 (18,29) DIM 4040048 / E 12/01 NOTES: A. B. C. D. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15). Falls within JEDEC MO-118 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MTSS003D – JANUARY 1995 – REVISED JANUARY 1998 DGG (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 48 PINS SHOWN 0,27 0,17 0,50 48 0,08 M 25 6,20 6,00 8,30 7,90 0,15 NOM Gage Plane 1 0,25 24 0°– 8° A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 48 56 64 A MAX 12,60 14,10 17,10 A MIN 12,40 13,90 16,90 DIM 4040078 / F 12/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Low Power Wireless www.ti.com/lpw Mailing Address: Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2006, Texas Instruments Incorporated