LSI/CSI UL ® LS7314-7315 LSI Computer Systems, Inc. 1235 Walt Whitman Road, Melville, NY 11747 (631) 271-0400 FAX (631) 271-0405 A3800 AC POWER CONTROLLERS A FEATURES: • 10 I/Os to Select/Indicate up to ten Power Levels • Inputs activated by Touch or Pushbutton Switch • Output switches pure and precise AC Power to Load • Operates with 50Hz/60Hz line frequency • Rugged, latchup-free process technology • +10V to +14V operation (Vss-VDD) • LS7314, LS7315 (DIP; LS7314-S, LS7315-S (SOIC) - See Figure 1 CONNECTION DIAGRAM - TOP VIEW INPUT/OUTPUT DESCRIPTION: PL1-PL10 (Pins 1-8, 15, 16) Ten inputs/outputs for selecting ten output phase angles (power levels). When no power level is selected (such as after system power-up) PL1-PL10 all act as inputs. When a power level is selected by applying a logic zero at one of these inputs for TH time (See Dynamic Characteristics), the output (TRIG) is turned on at the phase angle selected and the PL input switches status to become an output in order to drive a display, such as an LED. It switches back to the input state when another PL input is activated or when OFF is selected. (See Note 1) OFF (Pin 10) If TRIG is on, a logic 0 applied to the OFF input for TH time turns TRIG output off and switches the selected PL back to the input state. If TRIG is off, activating OFF leaves the circuit unaffected. Following an OFF activation, TRIG can be turned on by applying any PL input. (See Note 1) SYNC (Pin 12) Input for PLL reference frequency (50Hz/60Hz). All internal clock frequencies are synchronized with the SYNC input. CAP (Pin 11) Input for component connection for the PLL filter capacitor. 7314-040197-1 16 PL2 PL4 2 15 PL1 PL5 3 14 Vss (+V) PL6 4 13 TRIG PL7 5 12 SYNC PL8 6 11 CAP PL9 7 10 OFF 9 V DD (-V) LS7314 DESCRIPTION: The LS7314 - LS7315 are MOS integrated circuits specifically designed for appliance motor speed control, lighting control, etc. I/Os (PLs) are provided for selecting/indicating from one to ten power levels. The LS7315 is designed for pushbutton control. The LS7314 is designed for touch control. (See Figures 4A and 4B) 1 LSI APPLICATIONS: • Universal and shaded-pole motor speed control for modern appliance designs. Eliminates awkward mechanical switch assemblies and multi-tapped motor windings. (See Fig. 4C) • Multi-level light switches. (See Fig. 4D) PL3 PL10 8 FIGURE 1 TRIG (Pin 13) This output is designed to drive a triac in series with the load and control its firing angle with respect to the AC line. A 1ms output pulse width is provided to enable the triac to fire even with inductive loads which cause significant phase delays between voltage and current. Vss (Pin 14) Supply voltage positive terminal. VDD (Pin 9) Supply voltage negative terminal (ground). NOTE 1: LS7315 has an internal pullup resistor on this input and LS7314 does not. (See DC Electrical Characteristics.) FIGURE 2. TRIG PHASE ANGLE Ø SYNC Ø TRIG TW FIGURE 3. LS7314-LS7315 BLOCK DIAGRAM LEVEL 1 OFF POWER LEVEL ROM - 10 LEVEL 10 + DRIVER PL1 CONTROL LOGIC - 15 DIGITAL COMPARATOR PHASE ANGLE POINTER DRIVER 13 TRIG + DRIVER PL10 PHASE-LOCKED LOOP AND CLOCK GENERATOR - 8 V DD + V DD + V SS 11 - CAP 12 SYNC V SS FIGURE 4C and 4D NOTES TABLE 1. TRIG PHASE ANGLES, Ø (1) PL 1 2 3 4 5 6 7 8 9 10 Ø* 43° 55° 68° 81° 95° 108° 122° 134° 147° 160° % PWR (2) 8 16 26 40 55 69 82 90 96 99 *LS7314 & LS7315 (1) (2) Ø ** 81° 105° 116° 120° 123° 129° 134° 160° 167° 175° %PWR (2) 40 67 77 80 83 87 90 99 99 99 NOTE 1: Value for 5mA LEDs. NOTE 2: Use zener which produces 6.2V ±5% at 500µA or less, i. e. P/N MZ4627. NOTE 3: R6-C6 Snubber Network may be required for large inductive loads. NOTE 4: Tie all unused touch inputs together and return to Vss through 100k Ohm, 1/4W resistor. NOTE 5: The AC Mains Polarity shown is required for Touch Control applications. FIGURE 4C VALUE TABLE **LS7315-51 The TRIG Phase Angles shown in TABLE 1 are referenced to the SYNC input. Ø values are mask programmable. The percentage of Full Power delivered to a resistive load by the Triac Switch. CONDITION (1), (3) (1), (4) (2), (3) (2), (4) C2(µF) 0.47 0.33 0.68 0.47 (1) No LEDs (3) 115VAC, C2 = 200V FIGURE 4A. PUSHBUTTON INTERFACE FOR LS7315 PL10 PL1 FIGURE 4B. TOUCH INTERFACE FOR LS7314 SEE NOTE 4 OFF PL10 R8 R3 R3 = 10K , 1 / 4 W (2) 5mA LEDs (4) 220VAC, C2 = 400V PL1 R8 R7 OFF R8 R7 R7 Vss VDD R8 TP R8 TP R8 TP R7 = 1M to 5M , 1/4W (Select for Sensitivity) R8 = 2.7M , 1/4W for 115VAC Mains R8 = 4.7M , 1/4W for 220VAC Mains 7314-033197-2 FIGURE 4C. MOTOR SPEED CONTROL APPLICATION P G R6 C1 C5 - MT2 C6 AC MAINS + T MT1 SEE NOTE 3 C3 C4 Z1 R9 D1 L C2 9 11 12 13 SYNC TRIG CAP 14 L S 7 3 1 4 - L S 7 3 1 5 V SS V DD SEE NOTE 5 PL1 PL10 8 R2 M OFF 15 10 R1 PL1 PL10 OFF R5 N Use Fig. 4A or 4B Interface Circuits R4 Z2 C1 = 0.15µF, 200V (400V) * C2 = See Figure 4 Value Table C3 = 0.047µF C4 = 470pF C5 = 220uF C6 = 0.47µF, 200V (400V) * L = 100µH (200µH) * D1 = 1N4148 T = Q4004L4 (Q5004L4)* Typical R1 = 82Ω R2 = 1.5MΩ R4 = 560Ω (See Note 1) R5 = 10kΩ R6 = 1.8kΩ, 1W (2W) * R9 = 100Ω Z1 = 13V ± 5%, 1W Z2 = 6.2V, 1/4W (See Note 2) All resistors 1/4W, all capacitors 25V unless otherwise specified. * Indicates component change for 220VAC Mains. FIGURE 4D. MULTI-LEVEL WALL SWITCH DIMMER APPLICATION P .047µF G MT1 200V 0.15µF + Q40044L4 - MT2 13V 220µF .047µF 470pF 1W 1.5M 1N4148 100µH 115V AC MAINS 2W 2 0 0 V 9 82 0.68µF 12 13 SYNC TRIG 11 CAP L S 7 3 1 4 - L S 7 3 1 5 V SS V DD PL10 PL1 OFF 8 15 10 14 INCANDESCENT LAMP LOAD PL10 PL1 OFF N All Resistors 1/4W, all Capacitors 25V unless otherwise specified. Component Values are for use with 115VAC Mains and 2.5mA LEDs. Use Fig. 4A or Fig. 4B Interface Circuits 1K 6.2V, 1/4W (See Note 2) 7314-033197-3 10K MAXIMUM RATINGS: PARAMETER Storage Temperature Operating Temperature DC Supply Voltage Any Input Voltage SYMBOL TSTG TA Vss - VDD VIN VALUE -65 to +150 0 to +80 +20 Vss - 20 to Vss + 0.5 UNIT °C °C V V DC ELECTRICAL CHARACTERISTICS: (TA = 25˚C, all voltages referenced to VDD) SYMBOL VSS IDD MIN +10 - TYP +12 1.2 MAX +14 2 UNIT V mA CONDITION Vss = 12V, outputs off VISL VISH VIL VIH 0 2/3Vss 0 1/2Vss - 1/3Vss Vss 1/4Vss Vss V V V V - Input Current: SYNC Input IH - - 110 µA With Series 1.5MΩ Resistor to 115VAC Input Pull-up Resistance: For LS7315 PL, OFF RIN 50 100 200 kΩ - Output Voltage: TRIG, HI TRIG, LO VOH VOL Vss - Vss - 8 - V V - Output Current: TRIG, Sink IOS 25 - - mA PL Source IOPL 5 - - mA Vss = +12V VOL = Vss - 4V VOP L= Vss - 1V Supply Voltage Supply Current Input Voltage: SYNC, LO SYNC, HI All other inputs, LO All other inputs, HI DYNAMIC CHARACTERISTICS: SYMBOL MIN TYP MAX UNIT CONDITION SYNC frequency fS 40 - 70 Hz - PL, OFF hold time TH TH 50 60 - infinite infinite ms ms 60Hz SYNC 50Hz SYNC TRIG Pulse Width Tw Tw - 1.0 1.2 - ms ms 60Hz SYNC 50Hz SYNC The information included herein is believed to be accurate and reliable. However, LSI Computer Systems, Inc. assumes no responsibilities for inaccuracies, nor for any infringements of patent rights of others which may result from its use. 7310-032597-4