ETC MZ4614/D

MOTOROLA
SEMICONDUCTOR
TECHNICAL DATA
MZ4614
SERIES
500 mW DO-35 Glass
Zener Voltage Regulator Diodes
500 mW
DO-35 GLASS
GENERAL DATA APPLICABLE TO ALL SERIES IN
THIS GROUP
500 Milliwatt
Hermetically Sealed
Glass Silicon Zener Diodes
GLASS ZENER DIODES
500 MILLIWATTS
1.8–200 VOLTS
Specification Features:
• Complete Voltage Range — 1.8 to 200 Volts
• DO-204AH Package — Smaller than Conventional DO-204AA Package
• Double Slug Type Construction
• Metallurgically Bonded Construction
Mechanical Characteristics:
CASE 299
DO-204AH
GLASS
CASE: Double slug type, hermetically sealed glass
MAXIMUM LEAD TEMPERATURE FOR SOLDERING PURPOSES: 230°C, 1/16″ from
case for 10 seconds
FINISH: All external surfaces are corrosion resistant with readily solderable leads
POLARITY: Cathode indicated by color band. When operated in zener mode, cathode
will be positive with respect to anode
MOUNTING POSITION: Any
WAFER FAB LOCATION: Phoenix, Arizona
ASSEMBLY/TEST LOCATION: Seoul, Korea
MAXIMUM RATINGS (Motorola Devices)*
Rating
Symbol
DC Power Dissipation and TL ≤ 75°C
Lead Length = 3/8″
Derate above TL = 75°C
Value
Unit
500
4
mW
mW/°C
– 65 to +200
°C
PD
Operating and Storage Temperature Range
TJ, Tstg
PD , MAXIMUM POWER DISSIPATION (WATTS)
* Some part number series have lower JEDEC registered ratings.
0.7
HEAT
SINKS
0.6
0.5
0.4
3/8”
3/8”
0.3
0.2
0.1
0
0
20
40
60
80
100
120
140
160
180 200
TL, LEAD TEMPERATURE (°C)
Figure 1. Steady State Power Derating
Motorola TVS/Zener Device Data
500 mW DO-35 Glass Data Sheet
6-1
GENERAL DATA — 500 mW DO-35 GLASS
Designed for 250 mW applications requiring low leakage,
low impedance. Same as 1N4099 through 1N4104 and
1N4614 through 1N4627 except low noise test omitted.
• Voltage Range from 1.8 to 10 Volts
• Zener Impedance and Zener Voltage Specified for LowLevel Operation at IZT = 250 µA
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise specified. IZT = 250 µA and VF = 1 V Max @ IF = 200 mA for all
ELECTRICAL CHARACTERISTICS types)
Type
Number
(Note 1)
Nominal
Zener Voltage
VZ
(Note 2)
(Volts)
Max Zener
Impedance
ZZT
(Note 3)
(Ohms)
Max
Reverse
Current
IR
(µA)
MZ4614
MZ4619
MZ4625
MZ4627
1.8
3
5.1
6.2
1200
1600
1500
1200
7.5
0.8
10
10
NOTE 1. TOLERANCE AND VOLTAGE DESIGNATION
The type numbers shown have a standard tolerance of ±5% on the nominal zener voltage.
NOTE 2. ZENER VOLTAGE (VZ) MEASUREMENT
Nominal Zener Voltage is measured with the device junction in the thermal equilibrium with
ambient temperature of 25°C.
@
(Note 5)
Test
Voltage
VR
(Volts)
Max Zener Current
IZM
(Note 4)
(mA)
1
1
3
5
120
85
55
45
NOTE 4. MAXIMUM ZENER CURRENT RATINGS (IZM)
Maximum zener current ratings are based on maximum zener voltage of the individual units.
NOTE 5. REVERSE LEAKAGE CURRENT IR
Reverse leakage currents are guaranteed and are measured at VR as shown on the table.
NOTE 3. ZENER IMPEDANCE (ZZT) DERIVATION
NOTE 6. SPECIAL SELECTORS AVAILABLE INCLUDE:
The zener impedance is derived from the 60 cycle ac voltage, which results when an ac current having an rms value equal to 10% of the dc zener current (IZT) is superimposed on IZT.
A) Tighter voltage tolerances. Contact your nearest Motorola representative for more information.
500 mW DO-35 Glass Data Sheet
6-2
Motorola TVS/Zener Device Data
APPLICATION NOTE — ZENER VOLTAGE
Since the actual voltage available from a given zener diode
is temperature dependent, it is necessary to determine junction temperature under any set of operating conditions in order
to calculate its value. The following procedure is recommended:
Lead Temperature, TL, should be determined from:
TL = θLAPD + TA.
θLA is the lead-to-ambient thermal resistance (°C/W) and PD is
the power dissipation. The value for θLA will vary and depends
on the device mounting method. θLA is generally 30 to 40°C/W
for the various clips and tie points in common use and for
printed circuit board wiring.
The temperature of the lead can also be measured using a
thermocouple placed on the lead as close as possible to the tie
point. The thermal mass connected to the tie point is normally
large enough so that it will not significantly respond to heat
surges generated in the diode as a result of pulsed operation
once steady-state conditions are achieved. Using the measured value of TL, the junction temperature may be determined by:
θ JL , JUNCTION-TO-LEAD THERMAL RESISTANCE (°C/W)
GENERAL DATA — 500 mW DO-35 GLASS
θVZ, the zener voltage temperature coefficient, is found from
Figures 4 and 5.
Under high power-pulse operation, the zener voltage will
vary with time and may also be affected significantly by the
zener resistance. For best regulation, keep current excursions
as low as possible.
Surge limitations are given in Figure 7. They are lower than
would be expected by considering only junction temperature,
as current crowding effects cause temperatures to be extremely high in small spots, resulting in device degradation
should the limits of Figure 7 be exceeded.
L
L
300
2.4–60 V
200
62–200 V
100
0
0
0.2
0.4
0.6
0.8
1
L, LEAD LENGTH TO HEAT SINK (INCH)
1000
7000
5000
TYPICAL LEAKAGE CURRENT
AT 80% OF NOMINAL
BREAKDOWN VOLTAGE
2000
1000
700
500
200
I R , LEAKAGE CURRENT ( µ A)
∆V = θVZTJ.
400
Figure 2. Typical Thermal Resistance
TJ = TL + ∆TJL.
∆TJL is the increase in junction temperature above the lead
temperature and may be found from Figure 2 for dc power:
∆TJL = θJLPD.
For worst-case design, using expected limits of IZ, limits of
PD and the extremes of TJ(∆TJ) may be estimated. Changes in
voltage, VZ, can then be found from:
500
100
70
50
20
10
7
5
2
1
0.7
0.5
+125°C
0.2
0.1
0.07
0.05
0.02
0.01
0.007
0.005
+25°C
0.002
0.001
3
4
5
6
7
8
9
10
11
12
13
14
15
VZ, NOMINAL ZENER VOLTAGE (VOLTS)
Figure 3. Typical Leakage Current
Motorola TVS/Zener Device Data
500 mW DO-35 Glass Data Sheet
6-3
GENERAL DATA — 500 mW DO-35 GLASS
TEMPERATURE COEFFICIENTS
θVZ , TEMPERATURE COEFFICIENT (mV/ °C)
θVZ , TEMPERATURE COEFFICIENT (mV/ °C)
(–55°C to +150°C temperature range; 90% of the units are in the ranges indicated.)
+12
+10
+8
+6
+4
+2
RANGE
VZ @ IZT
(NOTE 2)
0
–2
–4
2
3
4
5
6
7
8
9
VZ, ZENER VOLTAGE (VOLTS)
10
11
12
100
70
50
30
20
3
2
1
10
200
180
160
140
VZ @ IZT
(NOTE 2)
100
120
130
140
150
160
170
180
190
20
+2
20 mA
0
0.01 mA
1 mA
NOTE: BELOW 3 VOLTS AND ABOVE 8 VOLTS
NOTE: CHANGES IN ZENER CURRENT DO NOT
NOTE: AFFECT TEMPERATURE COEFFICIENTS
–2
–4
200
3
4
100
70
50
C, CAPACITANCE (pF)
C, CAPACITANCE (pF)
200
1 V BIAS
20
10
50% OF
VZ BIAS
5
6
7
8
Figure 5. Effect of Zener Current
0 V BIAS
50
5
VZ, ZENER VOLTAGE (VOLTS)
TA = 25°C
100
100
VZ @ IZ
TA = 25°C
+4
Figure 4c. Range for Units 120 to 200 Volts
500
70
+6
VZ, ZENER VOLTAGE (VOLTS)
1000
30
50
VZ, ZENER VOLTAGE (VOLTS)
Figure 4b. Range for Units 12 to 100 Volts
θVZ , TEMPERATURE COEFFICIENT (mV/ °C)
θVZ , TEMPERATURE COEFFICIENT (mV/ °C)
Figure 4a. Range for Units to 12 Volts
120
VZ @ IZ (NOTE 2)
RANGE
10
7
5
TA = 25°C
0 BIAS
30
20
1 VOLT BIAS
10
7
5
50% OF VZ BIAS
3
2
2
1
1
1
2
5
10
20
50
100
VZ, ZENER VOLTAGE (VOLTS)
Figure 6a. Typical Capacitance 2.4–100 Volts
500 mW DO-35 Glass Data Sheet
6-4
120
140
160
180
190
200
220
VZ, ZENER VOLTAGE (VOLTS)
Figure 6b. Typical Capacitance 120–200 Volts
Motorola TVS/Zener Device Data
Ppk , PEAK SURGE POWER (WATTS)
GENERAL DATA — 500 mW DO-35 GLASS
100
70
50
RECTANGULAR
WAVEFORM
TJ = 25°C PRIOR TO
INITIAL PULSE
11 V–91 V NONREPETITIVE
30
5% DUTY CYCLE
1.8 V–10 V NONREPETITIVE
20
10
7
5
10% DUTY CYCLE
20% DUTY CYCLE
3
2
1
0.01
0.02
0.05
0.1
0.2
0.5
1
2
5
10
20
50
100
200
500
1000
PW, PULSE WIDTH (ms)
1000
500
1000
700
500
300
200
RECTANGULAR
WAVEFORM, TJ = 25°C
100
70
50
30
20
100–200 VOLTS NONREPETITIVE
10
7
5
3
2
1
0.01
ZZ , DYNAMIC IMPEDANCE (OHMS)
Ppk , PEAK SURGE POWER (WATTS)
Figure 7a. Maximum Surge Power 1.8–91 Volts
200
47 V
100
27 V
50
20
6.2 V
10
5
2
1
0.1
1
10
100
0.1
1000
0.2
0.5
PW, PULSE WIDTH (ms)
100
70
50
5 mA
20
20 mA
1000
TJ = 25°C
iZ(rms) = 0.1 IZ(dc)
f = 60 Hz
IZ = 1 mA
2
5
10
20
50
100
Figure 8. Effect of Zener Current on
Zener Impedance
MAXIMUM
MINIMUM
500
I F , FORWARD CURRENT (mA)
ZZ , DYNAMIC IMPEDANCE (OHMS)
1000
700
500
1
IZ, ZENER CURRENT (mA)
Figure 7b. Maximum Surge Power DO-204AH
100–200 Volts
200
TJ = 25°C
iZ(rms) = 0.1 IZ(dc)
f = 60 Hz
VZ = 2.7 V
10
7
5
2
200
100
50
20
75°C
10
25°C
5 150°C
0°C
2
1
1
1
2
3
5
7
10
20
30
50
70 100
VZ, ZENER VOLTAGE (VOLTS)
Figure 9. Effect of Zener Voltage on Zener Impedance
Motorola TVS/Zener Device Data
0.4
0.5
0.6
0.7
0.8
0.9
1
1.1
VF, FORWARD VOLTAGE (VOLTS)
Figure 10. Typical Forward Characteristics
500 mW DO-35 Glass Data Sheet
6-5
GENERAL DATA — 500 mW DO-35 GLASS
20
10
I Z , ZENER CURRENT (mA)
TA = 25°
1
0.1
0.01
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
29
30
VZ, ZENER VOLTAGE (VOLTS)
Figure 11. Zener Voltage versus Zener Current — VZ = 1 thru 16 Volts
10
I Z , ZENER CURRENT (mA)
TA = 25°
1
0.1
0.01
15
16
17
18
19
20
21
22
23
24
25
26
27
28
VZ, ZENER VOLTAGE (VOLTS)
Figure 12. Zener Voltage versus Zener Current — VZ = 15 thru 30 Volts
500 mW DO-35 Glass Data Sheet
6-6
Motorola TVS/Zener Device Data
GENERAL DATA — 500 mW DO-35 GLASS
I Z , ZENER CURRENT (mA)
10
TA = 25°
1
0.1
0.01
30
35
40
45
50
55
60
65
70
75
80
85
90
95
100
105
250
260
VZ, ZENER VOLTAGE (VOLTS)
Figure 13. Zener Voltage versus Zener Current — VZ = 30 thru 105 Volts
I Z , ZENER CURRENT (mA)
10
1
0.1
0.01
110
120
130
140
150
160
170
180
190
200
210
220
230
240
VZ, ZENER VOLTAGE (VOLTS)
Figure 14. Zener Voltage versus Zener Current — VZ = 110 thru 220 Volts
Motorola TVS/Zener Device Data
500 mW DO-35 Glass Data Sheet
6-7
GENERAL DATA — 500 mW DO-35 GLASS
Zener Voltage Regulator Diodes — Axial Leaded
500 mW DO-35 Glass
NOTES:
1. PACKAGE CONTOUR OPTIONAL WITHIN A AND B
HEAT SLUGS, IF ANY, SHALL BE INCLUDED
WITHIN THIS CYLINDER, BUT NOT SUBJECT TO
THE MINIMUM LIMIT OF B.
2. LEAD DIAMETER NOT CONTROLLED IN ZONE F
TO ALLOW FOR FLASH, LEAD FINISH BUILDUP
AND MINOR IRREGULARITIES OTHER THAN
HEAT SLUGS.
3. POLARITY DENOTED BY CATHODE BAND.
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
B
D
F
K
A
K
DIM
A
B
D
F
K
F
MILLIMETERS
MIN
MAX
3.05
5.08
1.52
2.29
0.46
0.56
—
1.27
25.40
38.10
INCHES
MIN
MAX
0.120 0.200
0.060 0.090
0.018 0.022
—
0.050
1.000 1.500
All JEDEC dimensions and notes apply.
CASE 299-02
DO-204AH
GLASS
(Refer to Section 10 for Surface Mount, Thermal Data and Footprint Information.)
MULTIPLE PACKAGE QUANTITY (MPQ)
REQUIREMENTS
Package Option
Type No. Suffix
MPQ (Units)
Tape and Reel
RL, RL2(1)
5K
Tape and Ammo
TA, TA2(1)
5K
NOTES: 1. The “2” suffix refers to 26 mm tape spacing.
NOTES: 2. Radial Tape and Reel may be available. Please contact your Motorola
NOTES: 2. representative.
Refer to Section 10 for more information on Packaging Specifications.
500 mW DO-35 Glass Data Sheet
6-8
Motorola TVS/Zener Device Data