124 Low-Power Quad Operational Amplifier Logic Diagram DESCRIPTION: • RAD-PAK® technology-hardened against natural space radiation • Total dose hardness: - > 100 krad (Si), depending upon space mission • Excellent Single Event Effects: • - SELTH LET = > 90 MeV/mg/cm2 • Package: -14 pin Rad-Pak® flat pack • Internally frequency compensated for unity gain • Large DC voltage gain • Wide bandwidth (unity gain): 1 MHz • Large output voltage swing 0V to V+ -1.5V • Input common - mode voltage range includes ground • Wide power supply range: - Single supply 3V to 32V - Dual supply ±1.5V to ±16V • Very low current drain (essentially independent of supply voltage): 700 uA • Low input biasing current: 45 nA • Low input offset voltage and current: 2mV, 5nA • Differential input voltage range equal to the power supply voltage Maxwell Technologies’s 124 independent, high gain, internally frequency compensated operational amplifiers feature a greater than 100 krad (Si) total dose tolerance, depending upon space mission. Using Maxwell’s radiation-hardened Rad-Pak® packaging technology, the 124 is designed specifically to operate from a single power supply over a wide range of voltages. The 124 also features operation from split power supplies, and the low power supply current drain is independent of the magnitude of the power supply voltage. Maxwell Technologies' patented RAD-PAK® packaging technology incorporates radiation shielding in the microcircuit package. It eliminates the need for box shielding while providing the required radiation shielding for a lifetime in orbit or space mission. In a GEO orbit, RAD-PAK provides greater than 100 krad (Si) radiation dose tolerance. This product is available with screening up to Class S. 04.02.02 Rev 5 (858) 503-3300 - Fax: (858) 503-3301 - www.maxwell.com All data sheets are subject to change without notice 1 ©2002 Maxwell Technologies All rights reserved. Memory FEATURES: 124 Low-Power Quad Operational Amplifier TABLE 1. PINOUT DESCRIPTION PIN SYMBOL DESCRIPTION 1, 7, 8, 14 OUTPUT 1 - 4 Ouput 2, 6, 9, 13 INPUT 1- – 4- Input (-) 3, 5, 10, 12 INPUT 1+ – 4+ Input (+) 4 V+ Power Supply 11 GND Ground TABLE 2. 124 ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL Supply Voltage MIN V+ Input Voltage -0.3 Input Current (VIN < -0.3V)1 UNIT 32 V 32 V +32 V 50 mA Output Short-Circuit to GND (One Amplifier) V+ < 15V, TA = 25°C2 Memory Differential Input Voltage MAX Continuous Storage Temperature Range TS -65 150 °C Operating Temperature Range TA -55 125 °C 250 V ESD Tolerance3 1. This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the op amps to go to the V+ voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than -0.3V (at 25°C). 2. Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground, the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V, continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result from simultaneous shorts on all amplifiers. 3. Human body model, 1.5 kΩ in series with 100 pF. TABLE 3. DELTA LIMITS PARAMETER VARIATION ICC ±10% of specified value in Table 4 04.02.02 Rev 5 All data sheets are subject to change without notice 2 ©2002 Maxwell Technologies All rights reserved. 124 Low-Power Quad Operational Amplifier TABLE 4. 124 ELECTRICAL CHARACTERISTICS (V+ = 5.0V, TA = -55 TO +125°C, UNLESS OTHERWISE SPECIFIED) PARAMETER Supply Current SYMBOL ICC TEST CONDITIONS Over Full Temperature Range RL = ∞ On All Op Amps V+ = 30V V+ = 5V SUBGROUPS MIN TYP MAX UNITS mA 1, 2, 3 1.5 0.7 3 1.2 Common-Mode Rejection Ratio CMRR DC, VCM = 0V to V+ -1.5V, TA = 25°C 1 70 85 dB Power Supply Rejection Ratio PSRR V+ = 5V to 30V TA = 25°C 1 65 100 dB f = 1 kHz to 20 kHz, TA = 25°C (Input Referred) 1 -120 dB V+ = 15V, TA = 25°C 1 40 mA Amplifier-to-Amplifier Coupling1 Short Circuit to Ground 2 IOS Input Offset Voltage 3 VIO Input Offset Current IOS Input Offset Current Drift Input Bias Current lib Input Common-Mode Voltage Range4 Large Signal Voltage Gain AVS Output Voltage Swing VOH Output Current 7 RS = 0Ω 1, 2, 3 IIN(+)-IIN(-), VCM = 0V 1, 2, 3 --- -- 100 nA RS = 0Ω 1, 2, 3 --- 10 -- pA/°C IIN(+) or IIN(-) 1, 2, 3 --- 40 300 nA V+ = +30V 1, 2, 3 0 V+ -2 V V+ = +15V (VO Swing = 1V to 11V) RL> 2 KΩ 1, 2, 3 25 7 µV/°C V/mV 1, 2, 3 V+ = 30V, RL = 2 kΩ RL = 10 kΩ 26 27 V 28 VOL V+ = 5V, RL = 10 kΩ 1, 2, 3 5 Source VO = 2V, VIN+ = +1V VIN- = 0V V+ = 15V VIN+ = +1V VIN- = 0V V+ = 15V 1, 2, 3 20 1, 2, 3 15 Sink mV 20 mV mA 1. Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This typically can be detected as this type of capacitance increases at higher frequencies. 2. Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground, the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V, continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result from simultaneous shorts on all amplifiers. 3. [email protected], RS=0Ω with V+ from 5V to 30V; and over the full input common-mode range (0V to V+ -1.5V). 4. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The upper end of the common-mode voltage range is V+ -1.5V (at 25°C), but either or both inputs can go to +32V without damage independent of the magnitude of V+. 04.02.02 Rev 5 All data sheets are subject to change without notice 3 ©2002 Maxwell Technologies All rights reserved. Memory Input Offset Voltage Drift 1, 2, 3 124 Low-Power Quad Operational Amplifier FIGURE 1. INPUT VOLTAGE RANGE Memory FIGURE 2. INPUT CURRENT 04.02.02 Rev 5 All data sheets are subject to change without notice 4 ©2002 Maxwell Technologies All rights reserved. 124 Low-Power Quad Operational Amplifier FIGURE 3. SUPPLY CURRENT Memory FIGURE 4. VOLTAGE GAIN 04.02.02 Rev 5 All data sheets are subject to change without notice 5 ©2002 Maxwell Technologies All rights reserved. 124 Low-Power Quad Operational Amplifier FIGURE 5. OPEN LOOP FREQUENCY RESPONSE Memory FIGURE 6. COMMON MODE REJECTION RATIO 04.02.02 Rev 5 All data sheets are subject to change without notice 6 ©2002 Maxwell Technologies All rights reserved. 124 Low-Power Quad Operational Amplifier FIGURE 7. VOLTAGE FOLLOWER PULSE RESPONSE Memory FIGURE 8. VOLTAGE FOLLOWER PULSE RESPONSE (SMALL SIGNAL) 04.02.02 Rev 5 All data sheets are subject to change without notice 7 ©2002 Maxwell Technologies All rights reserved. 124 Low-Power Quad Operational Amplifier FIGURE 9. LARGE SIGNAL FREQUENCY RESPONSE Memory FIGURE 10. OUTPUT CHARACTERISTICS CURRENT SOURCING 04.02.02 Rev 5 All data sheets are subject to change without notice 8 ©2002 Maxwell Technologies All rights reserved. 124 Low-Power Quad Operational Amplifier FIGURE 11. OUTPUT CHARACTERISTICS CURRENT SINKING Memory FIGURE 12. CURRENT LIMITING 04.02.02 Rev 5 All data sheets are subject to change without notice 9 ©2002 Maxwell Technologies All rights reserved. 124 Low-Power Quad Operational Amplifier Memory 14-PIN RAK-PAK® FLAT PACKAGE SYMBOL DIMENSION MIN NOM MAX A 0.119 0.132 0.145 b 0.010 0.017 0.022 c 0.004 0.005 0.009 D 0.250 0.255 0.260 E 0.250 0.255 0.260 E1 -- -- 0.290 E2 0.125 0.135 -- E3 0.030 0.060 -- e 0.050 BSC L 0.338 0.348 0.358 Q 0.021 0.025 0.030 S1 0.005 0.019 -- N 14 F14-03 Note: All dimensions in inches. 04.02.02 Rev 5 All data sheets are subject to change without notice 10 ©2002 Maxwell Technologies All rights reserved. Low-Power Quad Operational Amplifier 124 Important Notice: These data sheets are created using the chip manufacturer’s published specifications. Maxwell Technologies verifies functionality by testing key parameters either by 100% testing, sample testing or characterization. The specifications presented within these data sheets represent the latest and most accurate information available to date. However, these specifications are subject to change without notice and Maxwell Technologies assumes no responsibility for the use of this information. Maxwell Technologies’ products are not authorized for use as critical components in life support devices or systems without express written approval from Maxwell Technologies. Any claim against Maxwell Technologies must be made within 90 days from the date of shipment from Maxwell Technologies. Maxwell Technologies’ liability shall be limited to replacement of defective parts. Memory 04.02.02 Rev 5 All data sheets are subject to change without notice 11 ©2002 Maxwell Technologies All rights reserved. 124 Low-Power Quad Operational Amplifier Product Ordering Options Model Number 124 RP F X Option Details Feature Monolithic S = Maxwell Class S B = Maxwell Class B E = Engineering (testing @ +25°C) I = Industrial (testing @ -55°C, +25°C, +125°C) Package F = Flat Pack Radiation Feature RP = RAD-PAK® package Base Product Nomenclature Low-Power Quad Operational Amplifier 04.02.02 Rev 5 All data sheets are subject to change without notice Memory Screening Flow 12 ©2002 Maxwell Technologies All rights reserved.