66058 Features: Applications: • • • • • • • • • Mii SINGLE/DUAL CHANNEL, LOW-INPUT CURRENT, OPTOCOUPLER (Electrically similar to 6N140) DSCC Approved 8978501PX (Dual) and 8981001PX (Single) High current transfer ratio: 1000% typical 1500 Vdc isolation test voltage Low input current requirement: 0.5mA OPTOELECTRONIC PRODUCTS DIVISION Telephone ring detection Voltage level shifting Isolated receiver input Communication systems Medical systems DESCRIPTION The 66058 single/dual optocoupler utilizes infrared LEDs optically coupled to high gain photodarlington detectors. This unique optocoupler provides high CTR and low leakage current over the full military temperature range (-55° to +125°C). The 66058 is a 8 pin dual-in-line, hermetically sealed package and is available in standard and screened versions or tested to customer specifications. ABSOLUTE MAXIMUM RATINGS Storage Temperature........................................................................................................................................... -65°C to +150°C Operating Free-Air Temperature Range ............................................................................................................. -55°C to +125°C Lead Solder Temperature.........................................................................................260°C for 10s (1.6mm below seating plane) Peak Forward Input Current (each channel) ................................................................................................ 20mA (1ms duration) Average Forward Input Current ........................…............(see Note 1) ...............................................................................10mA Reverse Input Voltage ...............................................................................................................................................................5V Output Current - IO (each channel) ......................................................................................................................................40mA Output Power Dissipation (each channel) ........................(see Note 2) ..............................................................................50mW Supply Voltage - VCC ..........................................................(see Note 3)........................................................................0.5 to 20V Output Voltage - VO (each channel).……........................(see Note 3) ...................................................................... -0.5 to 20V Package Dimensions Schematic Diagram 0.370 [9.040] 0.390 [9.90] 8 7 REAR VIEW PIN ONE 6 DATE CODE YYWW USA XXXX 1 2 3 NC 1 8 Vcc A 2 7 EN K 3 6 V0 5 NC 4 4 5 GND TYPE NUMBER 0.170 [4.32]MAX 0.280 [7.11] 0.310 [7.88] 0.320 [8.13]MAX PIN ONE 0.007 [0.18] 0.013 [0.33] SIDE VIEW 0.020 [0.51] MIN .020 [0.51] MAX 0.90 [2.28] 0.110 [2.80] END VIEW A 1 8 K 2 7 V01 K 3 6 V02 A 4 5 GND Vcc ALL DIMENSIONS ARE IN INCHES [MILLIMETERS] Notes: 1. Derate IF at 0.33 mA/°C above 110°C. 2. Collector output power plus one half of the total supply power is total output power. Derate at 1.66mW/°C above 110°C. 3. The lowest total IOH over temperature is developed by keeping VCC as low as possible, but greater that 2 volts. The negative voltage at the detector side should be applied to Pin 10. MICROPAC INDUSTRIES, INC. OPTOELECTRONIC PRODUCTS DIVISION • 725 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 487-6918 www.micropac.com E-MAIL: [email protected] 3 - 36 66058 SINGLE/DUAL CHANNEL, LOW-INPUT CURRENT OPTOCOUPLER ELECTRICAL CHARACTERISTICS Ta = -55°C to 125°C unless otherwise specified. SYMBOL MIN TYP Current Transfer Ratio PARAMETER CTR 300 300 200 1000 750 400 Logic Low Output Voltage VOL 0.1 0.2 Low Level Supply Current UNITS TEST CONDITIONS NOTE % % % IF = 0.5mA, VO = 0.4V, VCC = 4.5V IF = 1.6mA, VO = 0.4V, VCC = 4.5V IF = 5.0mA, VO = 0.4V, VCC = 4.5V 1,2 1,2 1,2 0.4 0.4 V V IF = 0.5mA, IOL = 1.5mA, VCC = 4.5V IF = 5.0mA, IOL = 10mA, VCC = 4.5V 1 1,3 IOH .005 250 µA IF = 2µA, VO = VCC = 18V -XX1 -XX2 ICCH .01 10 20 µA µA IF1 = 0mA, VCC = 18V IF1 = IF2 = 0mA, VCC = 18V -XX1 -XX2 ICCL .01 2 4 mA mA IF1 = 1.6mA, VCC = 18V IF1 = IF2 =1.6mA, VCC = 18V 1.4 1.7 V IF = 1.6mA 1 V IR = 10µA 1 1.0 µA VI—0 = 1500Vdc, Relative Humidity = 45% tA = 25°C, t = 5s 4 6 6 4 60 50 30 µs IF = 0.5mA, VCC = 5.0V, RL = 4.7kΩ IF = 1.6mA, VCC = 5.0V, RL = 1.5kΩ IF = 5mA, VCC = 5.0V, RL = 680Ω 8 3 2 100 30 10 µs Logic High Output Current High Level Output Current MAX Input Forward Voltage VF Input Reverse Breakdown Voltage BVR Input-Output Insulation Leakage Current II—O Propagation Delay Time To High Output Level tPLH Propagation Delay Time To Low Output Level tPHL 5 µs µs IF = 0.5mA, VCC = 5.0V, RL= 4.7kΩ IF = 1.6mA, VCC = 5.0V, RL = 1.5kΩ IF = 5mA, VCC = 5.0V, RL = 680Ω µs µs TYPICAL CHARACTERISTICS Ta = 25°C, VCC = 5V Each Channel UNITS TEST CONDITIONS Input Capacitance PARAMETER SYMBOL CIN MIN 60 pF VF = 0, f = MHz, ta = 25°C 1 Capacitance (Input-Output) CI-O 1.5 pF f = 1MHz, ta = 25°C 1, 5 Input Diode Temperature Coefficient ∆vF -1.8 mV/°C IF = 1.6mA 1 ∆TA Resistance (Input-Output) RI-0 10 Ω VI—O = 500V, ta = 25°C 1, 5 Resistance (Input-Input) RI-I 10 Ω VI—I = 500V, ta = 25°C 6 Input-Input Insulation Leakage Current II-I 0.5 nA Relative Humidity = 45% VI—I = 500V, t = 5s 6 Common Mode Transient immunity at High Output Level CMH 1000 V/µs VCM = 50V P-P,VCC = 5.0V, RL = 1.5kΩ, IF = OmA, ta = 25°C 7,9 500 TYP MAX 12 12 NOTE Common Mode Transient CML 500 1000 V/µs VCM = 50V P-P,VCC = 5.0V, 8,9 Immunity at Low Output Level RL = 1.5kΩ, IF = 1.6mA, ta = 25°C NOTES: 1. Each channel. 2. CURRENT TRANSFER RATIO is defined as the ratio of output collector current, IO, to the forward LED input current., IF , times 100%. 3. IF = 2µA for channel under test. For all other channels, IF = 10mA. 4. Device considered a two-terminal device. 5. Measured between each input pair shorted together and all output pins shorted together. 6. Measured between each input pair shorted together. 7. CMH is the maximum tolerable common mode transient to assure that the output will remain in a high logic state (ie. VO > @.0V). 8. CML is the maximum tolerable common mode transient to assure that the output will remain in a low logic state (ie. VO < 0.8V). 9. In applications where dv/dt may exceed 50,000 V/µs (such as static discharge) a series resistor, RCC , should be included to protect the detector IC’s from destructively high surge currents. The recommended value is RCC = 1V = kΩ 0.6IF (mA) RECOMMENDED OPERATING CONDITIONS: PARAMETER Input Current, Low Level Input Current, High Level Supply Voltage SYMBOL IFL MIN 0 MAX 2 UNITS µA IFH 0.5 5 mA 2.0 18 VCC V MICROPAC INDUSTRIES, INC. OPTOELECTRONIC PRODUCTS DIVISION • 725 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 487-6918 www.micropac.com E-MAIL: [email protected] 3 - 37