DATA SHEET TFT COLOR LCD MODULE NL10276AC28-01L 36 cm (14.1 inches), 1024 × 768 pixels, Full-color, Multi-scan function, Built-in CRT interface board DESCRIPTION NL10276AC28-01L is a TFT (thin film transistor) active matrix color liquid crystal display (LCD) comprising amorphous silicon TFT attached to each signal electrode, a driving circuit, a CRT interface board and a backlight. NL10276AC28-01L has a built-in backlight with an inverter. The 36 cm (14.1 inches) diagonal display area contains 1024 × 768 pixels and can display full-color (more than 16 million colors simultaneously). Also, it has wide viewing angle and multi-scan function. FEATURES • High Luminance (200 cd/m2. typ.) • Low reflection • Multi-scan function: e.g. XGA, SVGA, VGA, VGATEXT, MAC • CRT interface board Auto recognition of input signal: Analog RGB signals, Synchronous signals (Hsync, Vsyn, Composite) • Incorporated edge type backlight (Two lamps into two lamp holders, Inverter) • Lamp unit replaceable (note) Digital control: e.g. Brightness, Display Position VESA : Video Electronics Standards Association Free supply voltage sequence DPMS : Display Power Management Signaling Corresponding to DDCI and DDC2B DDC1 : Display Data Channel 1 Corresponding to VESA DPMS DDC2B: Display Data Channel 2B APPLICATIONS • Desk-top type of PC • Engineering workstation • Display terminals for control system • Monitors for process controller On Screen Display Application with the OSD function might conflict with patents in Europe and/or the U.S.A. If you apply the OSD function, appreciate the patents at your side. The information in this document is subject to change without notice. Please confirm with the delivery specification before starting to design the system. Document No. EN0444EJ1V0DS00 (1st edition) Date Published May 2000 P Printed in Japan © 2000 NL10276AC28-01L STRUCTURE AND FUNCTIONS A color TFT (thin film transistor) LCD module is comprised of a TFT liquid crystal panel structure, LSIs for driving the TFT array, and a backlight assembly. The TFT panel structure is created by sandwiching liquid crystal material in the narrow gap between a TFT array glass substrate and a color filter glass substrate. After the driver LSIs are connected to the panel, the backlight assembly is attached to the backside of the panel. RGB (red, green, blue) data signals from a source system is modulated into a form suitable for active matrix addressing by the onboard signal processor and sent to the driver LSIs which in turn addresses the individual TFT cells. Acting as an electro-optical switch, each TFT cell regulates light transmission from the backlight assembly when activated by the data source. By regulating the amount of light passing through the array of red, green, and blue dots, color images are created with clarity. OUTLINE OF CHARACTERISTICS (at room temperature) Items 2 Description Display area 285.696 (H) × 214.272 (V) mm Drive system a-Si TFT active matrix Display colors Full-color Number of pixels 1024 (H) × 768 (V) Pixel arrangement RGB vertical stripe Pixel pitch 0.279 (H) × 0.279 (V) mm Module size 330.0 (H) × 255.0 (V) × 19.8 (D) mm (typ.) Weight 1230 g (typ.) Contrast ratio 150:1 (typ.) Viewing angle (more than the contrast ratio of 10:1) • • Horizontal : 50° (typ., left side, right side) Vertical : 20° (typ., up side), 35° (typ., down side) Designed viewing direction • • • Optimum grayscale ( γ = 2.2): perpendicular Wider viewing angle with contrast ratio: down side ( 6 o’clock) Wider viewing angle without image reversal: up side (12 o’clock) Color gamut 40% (typ., At center, To NTSC) Response time 11 ms (typ.), “white 100%” to “black 10%” Luminance 200 cd/m (typ.) Input signals Analog RGB signals, Synchronous signals (Hsync and Vsync or Composite) Backlight Edge light type: two cold cathode fluorescent lamps with an inverter Lamp holder: 141LHS08 Inverter : 141PW111 Supply voltage 12 V, 12 V (Logic/LCD driving, Backlight) Power consumption 16.0 W (typ.) 2 Data Sheet EN0444EJ1V0DS00 NL10276AC28-01L BLOCK DIAGRAM OF BASIC STRUCTURE I/F LCD module R G B HS/CS Vsync AIF Sync. Signal PLL CLK Timing Controller OSD LEDON LEDOFF SEL UP DOWN EXIT LEFT RIGHT RESET MENUSEL AMP Control signal Signal recognition Control signal H-driver ON/OFF 3072 lines V-driver LCD panel DC/DC converter VDD (+12 V) 768 lines H: 1024 × 3 (R, G, B) V: 768 Brightness control VDDB (+12 V) GNDB Inverter Backlight GND HS : Hsync CS : Composite synchronous signal Note: Neither GND nor GNDB is connected to frame. These should be connected in customers’ equipment. Data Sheet EN0444EJ1V0DS00 3 NL10276AC28-01L GENERAL SPECIFICATIONS Item Description Unit Module size 330 ± 0.5 (H) × 255.0 ± 0.5 (V) × 20.5 (max.) (D) mm Display area 285.696 (H) × 214.272 (V) mm Number of dots 1024 × 3 (H) × 768 (V) dots Pixel pitch 0.279 (H) × 0.279 (V) mm Dot pitch 0.093 (H) × 0.279 (V) mm RGB (Red, Green, Blue) vertical stripe – Full color color 1,350 (max.) g Pixel arrangement Display colors Weight ABSOLUTE MAXIMUM RATINGS Parameter Symbol Rating Unit VDD –0.3 to + 14 V VDDB –0.3 to + 14 V Logic input voltage VIn1 –0.3 to + 5.5 V R,G,B input voltage VIn2 –6.0 to + 6.0 V Storage temp. Tst –20 to + 60 °C Operating temp. Top 0 to 50 °C Module surface % Ta ≤ 40°C Supply voltage Relative Humidity ≤ 95% Ta = 25°C Ta = 25°C VDD = 12 V – ≤ 85% Absolute humidity Absolute humidity shall not exceed Ta = 50°C, RH = 85 % 40 < Ta ≤ 50°C g/m 3 Note: Measured at the LCD panel (Including self-fever) 4 Remarks Data Sheet EN0444EJ1V0DS00 Ta > 50°C Note No condensation NL10276AC28-01L ELECTRICAL CHARACTERISTICS (1) Logic, LCD driving, Backlight (Ta = 25°C) Item Symbol Min. Typ. Max. Unit VDD 11.4 12.0 12.6 V Logic and LCD driving VDDB 11.4 12.0 12.6 V Backlight Logic input “L” voltage VIL 0 – 0.8 V Logic input “H” voltage VIH 2.2 – 5.25 V HS/CS, Vsync, UP, DOWN, SEL, RESET, EXIT, RIGHT, LEFT, DDCCLK, DDCDAT Logic output “L” voltage VOL – – 0.4 V DDCDAT Logic output “H” voltage VOH 2.4 – – V Logic input “L” current IIL –1 – – µA Logic input “H” current IIH – – 1 µA Logic output “L” current 1 IOL1 – – 100 µA Logic output “H” current 1 IOH1 –100 – – µA Supply current (Pixel checked pattern) IDD – 630 900 mA VDD = 12.0 V – 170 200 mA Power saving mode VDD = 12.0 V – 700 900 mA VDDB = 12.0 V (Max. luminance) – 0.3 10 mA Power saving mode VDDB = 12.0 V Supply voltage IDDB Remarks HS/CS, Vsync DDCDAT (2) Video signal (R, G, B) input (Ta = 25°C) Items Min. Typ. Max. Unit 0 (black) 0.7 (white) *A Vp-p DC input level (black) −0.5 – +2.5 V Sync level −0.2 0.3 *B (0.6) Vp-p – – 1.4 Vp-p Maximum amplitude (white - black) *A + *B Remarks Note – G terminal (sync on green) – Note: Contrast adjustment is needed if the amplitude exceeds 0.7 Vp-p. Data Sheet EN0444EJ1V0DS00 5 NL10276AC28-01L Supply Voltage Sequence (1) Please note that the supply voltage must not be applied to the module while the control signals (SEL, UP, DOWN, EXIT, LEFT, RIGHT and RESET) are connected to GND. Otherwise the module may cause malfunction. (2) If the power supply voltage is applied while UP and DOWN are connected to GND, the input control signals become an ineffective mode. To reset this mode, turn off the power once and turn on the power while UP and DOWN are connected to GND. Then, the mode will be released. (3) Do not change MENUSEL setting while the module is operated. MENUSEL selection (Hierarchical type or Toggle type) is set when the power supply voltage is applied. (4) Inverter current wave Inverter current wave is as follows. 700 (mA) 0 (mA) Duty Luminance control frequency maximum luminance control: 100 % (Duty) minimam luminance control: 20 % (Duty) Luminance control frequency = Input Vsync frequency × K Input Vsync frequency ≤ 75 Hz: K = 4.6 Input Vsync frequency > 75 Hz: K = 3.6 (5) Ripple of supply voltage Please note that the ripple at the input connector of the module should be within the values shown in this table. If the ripple is beyond these values, the noise may appear on the screen. Supply voltage VDD (for logic and LCD driver) VDDB (for backlight) ≤ 100 mVp-p ≤ 200 mVp-p Acceptable range Note: The acceptable range of ripple voltage includes spike noise. Example of the power supply connection a) Separate the power supply Power VDD Power VDDB b) Put the filter Power Filter* VDD Filter* VDDB Filter* (reference value) L = 10 µH to 100 µH C = 10 µF to 100 µF 6 Data Sheet EN0444EJ1V0DS00 NL10276AC28-01L INTERFACE AND CONNECTOR PIN ASSIGNMENT (1) Logic and LCD driving CN1 Part No. : 1-353119-4 Adaptable socket : 1-353068-4 Supplier : Japan AMP Ltd. Pin No. Symbols Pin No. Symbols 1 B 8 Vsync 2 GND 9 GND 3 G 10 HS/CS 4 GND 11 GND 5 R 12 DDCCLK 6 GND 13 N.C. 7 GND 14 DDCDAT Figure from socket view 1 2 · · · · · · 13 14 Note 1: N.C. (No connection) must be open. CN3 Part No. : DF14A-25P-1.25H Adaptable socket : DF14-25S-1.25C Supplier : HIROSE ELECTRIC CO., LTD. Pin No. Symbols Pin No. Symbols 1 LEDON 14 EXIT 2 LEDOFF 15 GND 3 GND 16 N.C. 4 N.C. 17 GND 5 N.C. 18 GND 6 RIGHT 19 MENUSEL 7 LEFT 20 N.C. 8 RESET 21 N.C. 9 N.C. 22 N.C. 10 GND 23 GND 11 SEL 24 N.C. 12 UP 25 N.C. 13 DOWN Figure from socket view 1 2 · · · 24 25 Note 1: N.C. (No connection) must be open. Data Sheet EN0444EJ1V0DS00 7 NL10276AC28-01L CN5 Part No. : IL-Z-8PL-SMTY Adaptable socket : IL-Z-8S-S125C3 Supplier : Japan Aviation Electronics Industry Limited (JAE) Pin No. Symbols Pin No. Symbols 1 VDD 5 GND 2 VDD 6 GND 3 VDD 7 GND 4 VDD 8 GND Figure from socket view 8 7 · · · · · 2 1 (2) Backlight CN201 Part No. : IL-Z-11PL1-SMTY Adaptable socket : IL-Z-11S-S125C3 Supplier : Japan Aviation Electronics Industry Limited (JAE) Pin No. Symbols Pin No. Symbols 1 VDDB 7 N.C. 2 VDDB 8 N.C. 3 VDDB 9 N.C. 4 GNDB 10 N.C. 5 GNDB 11 N.C. 6 GNDB Figure from socket view 11 10 Note 1: N.C. (No connection) must be open. Rear view 1 CN1 14 1 1 11 CN201 CN3 25 8 CN5 1 8 Data Sheet EN0444EJ1V0DS00 · · · 2 1 NL10276AC28-01L (3) PIN FUNCTION Symbol I/O Logic Description HS/CS Input Negative Horizontal synchronous signal input or composite synchronous signal input (TTL level), Positive/Negative auto recognition Vsync Input Negative Vertical synchronous signal input (TTL level) Positive/Negative auto recognition, Clock input for DDC1 R Input – Red video signal input (0.7 Vp-p, input impedance 75 Ω) G Input – Green video signal input (0.7 Vp-p, input impedance 75 Ω) B Input – Blue video signal input (0.7 Vp-p, input impedance 75 Ω) LEDON Output Positive Indicator for LED power on “H”: LED select, “L”: Other status LEDOFF Output Positive Indicator for power save mode “H”: Power mode select, “L”: Other status DDCCLK Input Positive CLK for DDC2B DDCDAT Input/ Output Positive Data for DDC1/2B read/write SEL Input Negative Control function select signal (TTL level) SEL is pulled up in the module. Detail of the functions are mentioned in Page 13 CONTROL FUNCTIONS. “H” or “open”: SEL off, “L”: SEL on UP Input Negative Control signal (TTL level) The signal increases the value of the functions selected. UP is pulled up in tha module. “H” or “open”: UP off, “L”: UP on DOWN Input Negative Control signal (TTL level) The signal decreases the value of the functions selected. DOWN is pulled up in the module. “H" or “open”: DOWN off, “L” : DOWN on EXIT Input Negative Control function exit signal (TTL level) EXIT is pulled up in the module. “H" or “open”: EXIT off, “L”: EXIT on RIGHT Note1 Input Negative Control signal (TTL level) The signal increases the value of the functions selected. RIGHT is pulled up in the module. “H” or “open”: RIGHT off, “L”: RIGHT on LEFT Note1 Input Negative Control signal (TTL level) The signal decreases the value of the functions selected. LEFT is pulled up in the module. “H” or “open”: LEFT off, “L”: LEFT on RESET Note1 Input Negative Control signal (TTL level) The signal initializes the selected function. RESET is pulled up in the module. “H” or “open”: RESET off, “L”: RESET on MENUSEL Input – OSD design select signal (TTL level) MENUSEL is pulled up in the module. “H or open”: Hierarchical type “L”: Toggle type For detail, see Page 10 OSD MENU SELECT. Data Sheet EN0444EJ1V0DS00 9 NL10276AC28-01L Symbol I/O Logic Description VDD – – Power supply for Logic and LCD driving +12 V (±5%) VDDB – – Power supply for backlight +12 V (±5%) GND – – Ground for system GNDB – – Ground for backlight Notes 1: This terminal becomes effective only when the value of Button Sel is 7. Detail of the functions is mentioned in Page 27 INITIAL VALUE CHANGE FUNCTIONS. 2: Ground for system (GND) and backlight (GNDB) are not connected in the module. 3: 12 V for backlight should be started up within 300 ms, othernise, the protection circuit makes the backlight turn off. (4) OSD MENU SELECT OSD menu type Hierarchical type Toggle type MENUSEL “H” or “open” “L” How to adjust For details, see Page 27 INITIAL VALUE CHANGE FUCNTIONS. For details, see Page 27 INITIAL VALUE CHANGE FUCNTIONS. MENU Auto Adjust Brightness Clock Position Contrast Notes 1: If OSD menu type is changed, the adjustment of the type becomes default value. Then, It takes 5 seconds to display the changed menu after the supply voltage is input again. And, Indicators for both LEDON and LEDOFF are “ON” at one time during the 5 seconds. 2: The Initial value of Contrast ratio is as follows. Hierarchical type: 128:1 (typ.) Toggle type: 100:1 (typ.) 3: On Screen Display Application with the OSD function might conflict with patents in Europe and/or the U.S.A. If you apply the OSD function, appreciate the patents at your side. 10 Data Sheet EN0444EJ1V0DS00 NL10276AC28-01L (5) Equivalent circuit Symbol LEDON LEDOFF I/O Output Equivalent circuit RN2306 (Toshiba) Or equivalent Output <Example of LED circuit> LCD module Output R (330 Ω) LED LEDON LEDOFF R (330 Ω) SEL UP DOWN SW EXIT RIGHT LEFT RESET Data Sheet EN0444EJ1V0DS00 11 NL10276AC28-01L INPUT SIGNALS (1) SYNCHRONOUS SIGNAL This module is corresponding to the synchronous signals below. Synchronous signal Auto recognition mode HS/CS Vsync Sync. On Green Input Input Input or no input Composite synchronous mode Input (cs) No input Input or no input Sync. On Green mode No input No input Input Input (HS) No input Input or No input No input Input Input or no input No Input No input No input Separate synchronous signal mode (HS, Vsync) Power saving mode Notes 1: Power saving mode corresponds to VESA DPMA. 2: The module recognizes Sync on Green signal automatically, when the FUNC in SOG Sel of Sel Data is “Y”. Refer to Page 27 INITIAL VALUE CHANGE FUNCTION. (2) PRESET TIMING The 14 types of display timing shown below are preset in this module. The input synchronous signals are automatically recognized. Display size Vsync (Hz) Hsync (kHz) SYSTEM CLK (MHz) V Pulse (H) V B.Porch (H) H Pulse (CLK) H B.Porch (CLK) Sync Logic V, H 1 640 × 400 56.432 24.830 21.053 8 25 96 48 –,– * 2 640 × 480 59.992 31.469 25.175 2 33 96 48 –,– VGA 3 720 × 400 70.087 31.469 28.322 2 35 108 45 +,– VGA TXT 4 800 × 600 60.317 37.879 40.000 4 23 128 88 +,+ VESA 5 640 × 480 66.667 35.000 30.240 3 39 64 96 SonG 6 640 × 480 75.000 37.500 31.500 3 16 64 120 –,– VESA 7 720 × 400 85.039 37.927 35.500 3 42 36 144 +,– VESA 8 640 × 480 85.008 43.269 36.000 3 25 48 112 –,– * 9 1024 × 768 60.004 48.363 65.000 6 29 136 160 –,– VESA 10 800 × 600 75.000 46.875 49.500 3 21 80 160 +,+ VESA 11 832 × 624 74.565 49.735 57.283 3 39 64 224 SonG 12 800 × 600 85.061 53.674 56.250 3 27 64 152 +,+ * 13 1024 × 768 70.069 56.476 75.000 6 29 136 144 +,+ VESA 14 1024 × 768 75.029 60.023 78.750 3 28 96 176 +,+ VESA Preset No. * Out of specification. 12 Data Sheet EN0444EJ1V0DS00 Remarks Macintosh Macintosh NL10276AC28-01L Notes 1: Even if the preset timing is entered, a little adjustment of the functions such as Horizontal period, CLKdelay and display position, are required. The adjusted values are memorized in every preset No. 2: This module recognizes the synchronous signals with near preset timing of the frequency of HS, Vsync, even in the case that the signals other than the preset timing were entered. For instance, the module shows the display with presetting number 6 in the case of the following conditions: 640 × 480 dot; HS: 37.861kHz; Vsync: 72.809 Hz. Please note that using out of the preset timings may cause wrong magnification ratio, unfitness of control functions or other improper displays. 3: The display color scale may be different between Sync on Green Input and the others. CONTROL FUNCTIONS (1) EXPANSION MODES Expansion mode is a function to expand the screen size in different resolutions. For example, VGA signal has 640 × 480 pixels. But, if the display data can be expanded to 1.6 times vertically and horizontally, VGA screen image can be displayed fully on the screen of XGA resolution. This module automatically recognizes the timing shown in “PRESET TIMING” as an expansion mode. Please adopt this mode after evaluating display quality, because the appearance in expansion mode may become bad in some cases. The followings show display magnifications for each mode. Magnification Input display Number of pixels Vertical Horizontal XGA 1024 × 768 1.0 1.0 SVGA 800 × 600 1.25 1.25 VGA 640 × 480 1.6 1.6 VGA text 720 × 400 1.92 / 1.6 hiearchical / toggle 1.42 MAC 832 × 624 1.2 1.2 Data Sheet EN0444EJ1V0DS00 13 NL10276AC28-01L <DISPLAY IMAGE> (a) SVGA mode (800 u 600) XGA (1024 × 768) Black display area Horizontal: × 1.25 (1000 pixels) Vertical: × 1.25 (750 pixels) (b) VGA mode (640 u 480) Horizontal: × 1.6 (1024 pixels) Vertical: × 1.6 (768 pixels) (c) VGA text mode (720 u 400) (i) Hierarchical type XGA (1024 × 768) Black display area Horizontal: × 1.42 (1022 pixels) Vertical: × 1.92 (768 pixels) (ii) Hierarchical type XGA (1024 × 768) Black display area Horizontal: × 1.42 (1022 pixels) Vertical: × 1.6 (640 pixels) (d) 832 u 624 MAC mode (832 u 624) XGA (1024 × 768) Black display area Horizontal: × 1.2 (998 pixels) Vertical: × 1.2 (748 pixels) 14 Data Sheet EN0444EJ1V0DS00 NL10276AC28-01L (2) DDC FUNCTION This function is corresponding to VESA DDCTM and EDIDTM (Structure Version 1). Follow the specifications of the IC when you write data. Then VCLK should be fixed on “H.” Please write a data into necessary addresses in advance when you use this function. Data “55H” in address “00H” and “FFH” in other address are already programmed when shipping. The input equivalent circuit diagram is as follow. EDID: Extended Display Identification Data <Internal circuit diagram> Vsync VCLK DDCCLK SCL DDCDAT SDA Product: Microchip Technology Inc. 24LCS21 or equivalent (3) DPMS This function is corresponding to VESA DPMSTM Standard. VESA DPMS Standard NL10276AC28-01L Signal State Power saving Horizontal Vertical Recovery time Power saving Video Recovery time On Pulses Pulses Active None Not applicable None Not applicable Stand-by No pulses Pulses Blanked Minimum Short Maximum Short Suspend Pulses No pulses Blanked Substantial Longer Maximum Short Off No pulses No pulses Blanked Maximum System dependent Maximum Short Data Sheet EN0444EJ1V0DS00 15 NL10276AC28-01L (4) CONTROL FUNCTION ITEMS No. Form Function items 1 Auto adjust Clock and Position auto adjust 2 Brightness Brightness of backlight control 3 Clock 4 Position 5 Contrast 6 Color Level H. Size Horizontal display period adjust Clock Phase CLK-phase adjust H. Position Horizontal position adjust V. Position Vertical position adjust W, R, G, B White-level of video signals; synchronous color and each color are controllable. W White-level of video signal synchronous color control W, R, G, B Color-level of video signals; synchronous color and each color are controllable. W Color-level of video signal synchronous color control 7 Information Video signal information Display multi-scan function, Hsync and Vsync frequency 8 OSD Position OSD position adjust The display position of OSD can be moved. 9 Config Sync on Green signal. Response or non-response to Sync on Green signal is selected. When non-response is selected by Page 27 INITIAL VALUE CHANGE FUNCTIONS, config is not displayed. 10 All Reset Reset to initial value. The values in No. 1 to No. 6, No. 8 and No. 9 are returned to the initial values. In order to achieve the best picture quality, the above functions should be adjusted by setting SEL, UP, DOWN, LEFT, RIGHT, RESET and EXIT signals. Each adjusted value is memorized as soon as SEL is selected or time out mode is valid and the memorized values are not affected even if the power is switched off. But the selected value is not memorized in case where a selected mode is changed to another or the power is turned off before time out. 16 Data Sheet EN0444EJ1V0DS00 NL10276AC28-01L (5) FLOW CHART OF CONTROL FUNCTIONS (a) Hierarchical type (4 switches used for adjustment; SEL; UP; DOWN; EXIT) * For details, see Page 27 INITIAL VALUE CHANGE FUNCTIONS – 6. Sel Data, Button Sel Start (SEL): OSD opens (EXIT): OSD closes MENU Auto Adjust Brightness Clock Position Contrast (SEL) (EXIT), (SEL) Auto Adjust (DOWN) (UP) No Yes ↓ (UP), (DOWN) (EXIT) Auto Adjust No MENU Auto Adjust Brightness Clock Position Contrast ↑ (UP), (DOWN) (SEL): Auto Adjust Yes (EXIT): OSD closes (SEL) (EXIT) (UP), (DOWN) Brightness (DOWN) (UP) ↓ (SEL) ↑ (SEL), (EXIT) Reset Brightness No ↓ (UP), (DOWN)) Yes ↑ (UP), (DOWN)) Continue to next page Data Sheet EN0444EJ1V0DS00 17 NL10276AC28-01L ↓ (UP), (DOWN)) ↑ (UP), (DOWN)) Reset Brightness (DOWN) (EXIT): Cancel (UP) No MENU Auto Adjust Brightness Clock Position Contrast (SEL): Initialize Yes (EXIT): OSD closes (SEL) (EXIT) (UP) H. Size (DOWN) Clock Phase (UP) (UP), (DOWN) ↓ (SEL) ↑ (EXIT) (UP) / (DOWN) (SEL): Reset H. Size H. Size Clock Phase Similar behavior to that of “H. Size” adjustment shown above. H. Size (UP), (DOWN) MENU Auto Adjust Brightness Clock Position Contrast (DOWN) (UP) Clock Phase (EXIT): OSD closes (SEL) (EXIT) (DOWN) (EXIT) H. Position V. Position Continue to next page 18 Data Sheet EN0444EJ1V0DS00 Similar behavior to that of “Clock” adjustment shown above. NL10276AC28-01L ↓ (DOWN) ↑ (UP) MENU Auto Adjust Brightness Clock Position Contrast (EXIT): OSD closes (SEL) (EXIT) [S-Cnt Sel is ON] (SEL), (UP), (DOWN), (EXIT) (DOWN) (UP) Contrast W R G B For details, see Page 27 INITIAL VALUE CHANGE FUNCTIONS –6. Sel Data –. [S-Cnt Sel is OFF] (UP) / (DOWN) Contrast W * MENU Color Level Information OSD Position Config All Reset (EXIT): OSD closes (SEL) (EXIT) [S-Lvl Sel is ON] (SEL), (UP), (DOWN), (EXIT) (DOWN) (UP) Color Level W R G B Color Level W For details, see Page 27 INITIAL VALUE CHANGE FUNCTIONS –6. Sel Data –. [S-Cnt Sel is OFF] (UP) / (DOWN) * MENU Color Level Information OSD Position Config All Reset (DOWN) (UP) (EXIT): OSD closes (SEL) (EXIT) Continue to next page Data Sheet EN0444EJ1V0DS00 19 NL10276AC28-01L (DOWN) (UP) (SEL) (EXIT) Information 1024 × 788 Hf 60.0 kHz Vf 75.0 Hz * MENU Color Level Information OSD Position Config All Reset (DOWN) (UP) * MENU Color Level Information OSD Position Config All Reset (DOWN) (UP) * MENU Color Level Information OSD Position Config All Reset (EXIT): OSD closes (SEL) (EXIT) (UP) / (DOWN): OSD Position select OSD Position Center Center/LeftUp/RightUp/ LeftDown/RightDown (SEL): Reset OSD Position (EXIT): OSD closes (SEL) (EXIT) (UP) / (DOWN): Select “Sync on Green” acceptability [ON/OFF] Sync on Green OFF (SEL): Reset Sync on Green (EXIT): OSD closes * Config is not indicated, when SoG Sel MENU “N” of Page 27 INITIAL VALUE CHANGE FUNCTIONS –6. Sel Data – is selected. (SEL) (EXIT) All Reset No Yes ↓ (UP), (DOWN) (EXIT) ↑ (UP), (DOWN) All Reset (SEL): All reset No 20 Yes Data Sheet EN0444EJ1V0DS00 NL10276AC28-01L (b) Hierarchical type (7 switches used for adjustment: SEL; UP, DOWN; EXIT; LEFT; RIGHT; RESET) * For details, see Page 27 INITIAL VALUE CHANGE FUNCTIONS – 6. Sel Data, Button Sel -. Start (SEL): MENU open MENU Auto Adjust Brightness Clock Position Contrast (DOWN) (EXIT): OSD closes (SEL) (EXIT), (SEL) Auto Adjust (UP) No Yes ↓ (LEFT), (RIGHT), (UP), (DOWN) ↑ (LEFT), (RIGHT), (UP), (DOWN) (EXIT) Auto Adjust No MENU Auto Adjust Brightness Clock Position Contrast (SEL): Auto Adjust Yes (EXIT): OSD closes (SEL) (EXIT) (LEFT), (RIGHT) Brightness (DOWN) (UP) ↓ (RESET) ↑ (SEL), (EXIT) Reset Brightness No Yes ↓ (LEFT), (RIGHT), (UP), (DOWN) ↑ (LEFT), (RIGHT), (UP), (DOWN) Continue to next page Data Sheet EN0444EJ1V0DS00 21 NL10276AC28-01L ↓ (LEFT), (RIGHT), (UP), (DOWN) ↑ (LEFT), (RIGHT), (UP), (DOWN) (DOWN) (UP) Reset Brightness No Yes (EXIT): OSD closes MENU Auto Adjust Brightness Clock Position Contrast (DOWN) (EXIT): Cancel (SEL): Initialize (SEL) (EXIT) (LEFT) / (RIGHT) (RESET): Reset H. Size H. Size (UP) Clock Phase ↓ (UP), (DOWN) (EXIT) H. Size ↑ (UP), (DOWN) (LEFT) / (RIGHT) (RESET): Reset Clock Phase Clock Phase MENU Auto Adjust Brightness Clock Position Contrast (EXIT): OSD closes (SEL) (EXIT) Position (DOWN) (UP) Continue to next page 22 Data Sheet EN0444EJ1V0DS00 (LEFT) / (RIGHT) / (UP) / (DOWN) (RESET): Reset Position [H.Position and V.Position] NL10276AC28-01L ↓ (DOWN) ↑ (UP) MENU Auto Adjust Brightness Clock Position Contrast (DOWN) (UP) (EXIT): OSD closes (SEL) (EXIT) [S-Cnt Sel is ON] (SEL), (UP), (DOWN), (LEFT) / (RIGHT), (EXIT), (RESET) Contrast W R G B For details, see Page 27 INITIAL VALUE CHANGE FUNCTIONS –6. Sel Data –. [S-Cnt Sel is OFF] (RIGHT), (UP) / (LEFT), (DOWN) Contrast W * MENU Color Level Information OSD Position Config All Reset (DOWN) (UP) (EXIT): OSD closes (SEL) (EXIT) Color Level W R G B Color Level W [S-Cnt Sel is ON] (SEL), (UP), (DOWN), (LEFT) / (RIGHT), (EXIT), (RESET) For details, see Page 27 INITIAL VALUE CHANGE FUNCTIONS –6. Sel Data –. [S-Cnt Sel is OFF] (RIGHT), (UP) / (LEFT), (DOWN) * MENU Color Level Information OSD Position Config All Reset (DOWN) (UP) (EXIT): OSD closes (SEL) (EXIT) Continue to next page Data Sheet EN0444EJ1V0DS00 23 NL10276AC28-01L (DOWN) (UP) (SEL) (EXIT) Information 1024 × 788 Hf 60.0 kHz Vf 75.0 Hz * MENU Color Level Information OSD Position Config All Reset (DOWN) (UP) * MENU Color Level Information OSD Position Config All Reset (DOWN) (UP) * MENU Color Level Information OSD Position Config All Reset (EXIT): OSD closes (SEL) (EXIT) (LEFT) / (RIGHT) / (UP) / (DOWN): OSD Position selects OSD Position Center Center/LeftUp/RightUp/ LeftDown/RightDown (SEL): Reset Position (SEL): Reset OSD Position (EXIT): OSD closes (SEL) (EXIT) (LEFT) / (LIGHT) / (UP) / (DOWN): Sync on Green select [ON/OFF] Sync on Green OFF (SEL): Reset Sync on Green (EXIT): OSD closes * Config is not indicated, when SoG Sel selected MENU “N” by Page 27 INITIAL VALUE CHANGE FUNCTIONS –6. Sel Data –. (SEL) (EXIT) All Reset No Yes ↓ (LEFT), (RIGHT), (UP), (DOWN) (EXIT) All Reset No 24 ↑ (LEFT), (RIGHT), (UP), (DOWN) (SEL): Initialized Yes Data Sheet EN0444EJ1V0DS00 NL10276AC28-01L Notes 1: The value of the selected signals by LEFT, RIGHT, UP and DOWN key is continuously increased if the input signal is held for more than approx. one second. If it’s less than one second, the value is increased by one. 2: RESET signal initializes the value selected by SEL key. “All reset” function initializes all the values adjusted before. 3: No key input for more than ten seconds shall be regarded as “Time out”. 4: Contrast W is synchronous with Contrast R, Contrast G, and Contrast B. 5: Color Level W is synchronous with Color Level R, Color Level G and Color Level B. Data Sheet EN0444EJ1V0DS00 25 NL10276AC28-01L (c) Toggle type (SEL, UP, DOWN and EXIT) (UP), (DOWN): + or ð (EXIT): Initialize Start ↓ (SEL) (UP), (DOWN) (EXIT) ↓ (SEL) (UP), (DOWN) (EXIT) ↓ (SEL) (UP), (DOWN) (EXIT) ↓ (SEL) (UP), (DOWN) (EXIT) ↓ (SEL) (UP), (DOWN) (EXIT) ↓ (SEL) (UP), (DOWN) (EXIT) ↓ (SEL) ALL RESET Press Reset Key Over 2 Seconds (EXIT) ↓ (SEL) OSD closes Notes 1: The value of the signals selected by UP and DOWN key is continuously increased if the input signal is held for more than approx. one second. 2: RESET signal initializes the value selected by SEL key. All reset function initializes all the values adjusted before. 3: No key input for more than five seconds shall be regarded as “Time out”. 4: EXIT is valid when connected to GND for more than approx. two seconds. 26 Data Sheet EN0444EJ1V0DS00 NL10276AC28-01L (6) INITIAL VALUE CHANGE FUNCTIONS Initial value, OSD items, etc. can be changed. The changed initial value becomes initial value in each preset timing, and is applicable when it is reset (including All Reset). • How to transpose to initial value change mode. Hierarchical type: Connect SET and UP to GND at the same time when OSD function is in “information” mode. Toggle type : Connect SEL to GND while UP is connected to GND when OSD function is in “All Reset” mode. • Operation SEL, UP, DOWN, and EXIT • How to return to normal mode Connect EXIT to GND or turn off Power supply when OSD is closed. Both LEDON and LEDOFF become “H” when this mode is operating. No. 1 Form Compatible Function items It becomes valid when Toggle menu type is only selected. YES : Sync on Green The initial value of contrast (RGB synchronous) becomes 128. NO : No Sync on Green The initial value of contrast (RGB synchronous) becomes 100. The NEC factory value: NO. 2 Brightness The maximum value of brightness of backlight can be changed. Initial value: 100 3 Color Level The initial value of color level can be changed. Initial value: 128 4 Contrast The initial value of contrast can be changed. Initial value: 128 (When NO is selected by Compatible in Toggle menu type, the initial value of RGB synchronous only is 100. As for RGB synchronous, the setup value described in this item becomes valid as the Initial value regardless of the selections state of Compatible.) 5 LCD Data Mode No. of Page 12 PRESET TIMINGS is displayed. HSE The initial value of the Double Value can be changed. Delay The value of the CLK delay can be changed. (Initial value can not be changed.) Initial value: 0 VD The initial value of the up-down position of the display position can be changed. HD The initial value of the left-right position of the display position can be changed. Auto Adjust Auto adjust Par. Delay The compensation value of Delay of the auto adjust can be changed. Valid range: 0 to 255 Par. HD The compensation value of horizontal position of the auto adjust can be changed. Valid range: 0 to 127 Continue to next page Data Sheet EN0444EJ1V0DS00 27 NL10276AC28-01L No. Form Function items 5 LCD Data LCD Reset The values set in No. 5 LCD Data, return to the NEC factory settings 6 Sel Data S – Lvl Sel The adjustment of each individual RGB can be made impossible by the adjustment of the Color level. In this case, the adjustment item of each individual RGB is not displayed on the menu screen. ON : Individual adjustment is available. OFF : Individual adjustment is impossible Initial value: ON. S – Cnt Sel The adjustment that RGB is independent can be made impossible by the adjustment of the Color level. In this case, the adjustment item that RGB is independent is not displayed on the menu screen. ON : Individual adjustment is available. OFF : Individual adjustment is impossible Initial value: ON. SOG Sel Select or non-select of Sync on Green and display or non-display of select menu can be selected. When non-display is selected, Config is not displayed. • FUNC (Y: Sync on Green selection) (N: Sync on Green non-selection) • MENU (Y: Select MENU display.) (N: Select MENU non-display.) Initial value (FUNC: Y; MENU: N) * This item becomes effective only when the Hierarchical menu type is selected. But it becomes invalid when Toggle menu type is selected. MENU Sel B (blue) or S (transparency) can be selected for the Background Color of the OSD menu. Initial value: B Button Sel 4 (SEL, UP, DOWN and EXIT) or 7 (SEL, UP, DPWN, RIGHT, LEFT, EXIT and RESET) number of adjustment switch can be selected. Initial value: 7 PSOSD Sel Display or no display for Power Save OSD can be selected. (For detail, see Page 29 INFORMARION DISPLAY BY OSD) ON: Display Initial value: OFF OFF: No display 7 Information Input signal information is displayed. 8 OSD Position The initial value of OSD display position can be changed. C: Center UL: Upper left UR: Upper right DL: Down left DR: Down right Initial value: C 9 Used Time Used time in normal and Power save state is displayed. Used time is recorded in every five minutes. But it is not recorded when Power supply is cut off within five minutes. 10 Full Reset All values are returned to NEC factory settings. It takes about seven seconds. * The value of No.5 LCD Data are memorized in every Preset timing. * Selected adjustment item is displayed with OSD. * Data except Auto Adjust of 5. LCD Data are saved when it is returned in the extreme upper menu. But it is not saved if the power supply is cut off halfway. * All adjust value is returned to the NEC factory value when menu type is changed. * Please sufficiently evaluate the compensation values that Par. Delay and Par. HD of No.5 LCD Data need to set up, before determining the values. 28 Data Sheet EN0444EJ1V0DS00 NL10276AC28-01L (7) INFORMARION DISPLAY BY OSD (a) Power save: Frequency of horizontal, vertical synchronous signal is displayed for four seconds at the time of the Power Save mode switchover. Power Save Hf 0.0 kHz Vf 0.0 Hz am * It is displayed when Horizontal synchronous signal frequency (Hf) and vertical synchronous signal frequency (Vf) are the following cases: (1) Hf < 10 KHz (2) Vf < 40 Hz (3) (1) and (2) * It is not displayed when “Power Save OSD no display” form is selected with Page 27 INITIAL VALUE CHANGE FUNCTIONS - 6. Sel Data, PSOSD Sel -. (b) Out of Range:Each frequency is displayed for four seconds when the Horizontal and Vertical synchronous signal outside the corresponding range is inputted. Out of Range Hf 64.0 kHz Vf 60.0 Hz * It is displayed when Horizontal synchronous signal frequency (Hf) and vertical synchronous signal frequency (Vf) are the following cases: (1) 10 KHz ≤ Hf < 23 KHz or 61.5 KHz < Hf (2) 40 Hz ≤ Vf < 50 Hz or 200 Hz < Vf (3) (1) and (2) But it is not displayed when either Hf or Vf is power save mode. * Display or no display for Out of Range can not be selected. (c) Disable :It is displayed for four seconds if the switch for adjustment is disable. Key Disable Data Sheet EN0444EJ1V0DS00 29 NL10276AC28-01L (8) INPUT SIGNAL AND DISPLAY POSITION - XGA STANDARD TIMING Pixels D (0,0) D (0,1) D (0,2) ••• ••• D (0,1023) D (1,1) D (1,2) ••• ••• D (1,1023) D (2,0) D (2,1) D (2,2) ••• ••• D (2,1023) • • • • • • • • • • • • D (767,0) D (767,1) D (767,2) D (1,0) • • • • V Pulse ••• ••• V B. Porch Vsync 1 line Hsync XGA mode (VD = “35”) → 0 1 R G B 2 3 4 5 ··· 35 Invalid 36 37 Valid D (0, X), D (1, X), D (2, X) H Pulse H B. Porch Hsync 1 clk CLK XGA mode (HD = “296”) → 0 1 2 3 4 5 ··· 296 297 298 tda R G B Invalid Valid D (X, 0), D (X, 1), D (X, 2) Note: The tda should be more than 4ns 30 Data Sheet EN0444EJ1V0DS00 D (767, 1023) NL10276AC28-01L OPTICAL CHARACTERISTICS (Ta = 25°C, VDD = 12 V, VDDB = 12 V, Note 1) Item Symbol Condition Min. Typ. Max. Unit Remark CR γ = 2.2 viewing angle θR = 0°, θL = 0°, θD = 0°, White/Black, at center 80 150 − − Note 2 Lvmax White, at center 150 200 − cd/m − White − – 1.30 − Symbol Condition Min. Typ. Max. Contrast ratio CR Best contrast angle θR = 0°, θL = 0°, θD = 5° White/Black, at center − 300 − Color gamut C θR = 0°, θL = 0°, θU = 0°, θD = 0° at center, to NTSC 35 40 − % − Viewing angle range θR CR > 10, θU = 0°, θD = 0° White/Black, at center 40 50 − deg. Note 5 40 50 − deg. CR > 10, θR = 0°, θL = 0° White/Black, at center 15 20 − deg. 25 35 − deg. ms Note 6 % − Contrast ratio Luminance Luminance uniformity 2 Note 3 Note 4 Reference data (Ta = 25°C, VDD = 12 V, VDDB = 12 V, Note 1) Item θL θU θD Response time Luminance control range Ton Black (0 %) to White (90 %) − 11 25 Toff White (100 %) to Black (10 %) − 40 80 − Maximum luminance: 100 % at center. − 30 to 100 − Unit Remark Note 2 Notes 1: The luminance is measured after 20 minutes from the module works, with all pixels in “white.” The typical value is measured after luminance saturation. Display mode: VESA XGA-75 Hz RGB input voltage: 0.7 Vp-p Contrast: Default 2: The contrast ratio is calculated by using the following formula. Contrast ratio (CR) = Luminance with all pixels in “white” Luminance with all pixels in “black” 3: The luminance is measured after 20 minutes from the module works, with all pixels in “white”. The typical value is measured after luminance saturation, more than one hour after burn-in. The timing is XGA standard mode, preset No. 9. 50 cm Photo-detector (TOPCON BM-5A) 1° LCD module Data Sheet EN0444EJ1V0DS00 31 NL10276AC28-01L 4: Luminance uniformity is calculated by using the following formula. Maximum luminance Luminance uniformity = Minimum luminance The luminance is measured at near the five points shown below. Column 171 512 853 1 2 128 Row 384 3 4 640 5 5: Definitions of viewing angle are as follows. Perpendicular θL 12 o’clock θU –x θD θR +y –y +x 6: Definitions of response time is as follows. Photo-detector output signal is measured when the luminance changes “white” to “black” or “black” to “white”. White 100 % 90 % Luminance Black 10 % 0% Ton 32 Toff Data Sheet EN0444EJ1V0DS00 NL10276AC28-01L RELIABILITY TEST SPECIFICATIONS Test item Test condition Judgment High temperature/humidity operation 50 r2qC, 85% relative humidity 240 hours, Display data is black. Note 1 Heat cycle (operation) <1> 0qC r3qC ··· 1 hour 55qC r3qC ··· 1 hour <2> 50 cycles, 4 hours/cycle <3> Display data is black. Note 1 Thermal shock (non-operation) <1> ð20qC r3qC ··· 30 minutes 60qC r3qC ··· 30 minutes <2> 100 cycles <3> Temperature transition time is within 5 minutes. Note 1 Vibration (non-operation) <1> 5-100 Hz, 19.6 m/s (2G) 1 minute/cycle, X, Y, Z direction <2> 50 times each direction Mechanical shock (non-operation) <1> 294 m/s (30G), 11 ms X, Y, Z direction <2> 3 times each direction ESD (operation) 150 pF, 150 :, r10 KV 9 places on a panel 2 Notes 1, 2 2 Notes 1, 2 Note 1 Note 3 10 times each place at one-second intervals Dust (operation) 15 kinds of dust (JIS-Z 8901) Hourly 15 seconds stir, 8 times repeat Note 1 Notes 1: Display function is checked by the same condition as LCD module out-going inspection. 2: Physical damage. 3: Discharge points are shown in the following figure. Data Sheet EN0444EJ1V0DS00 33 NL10276AC28-01L GENERAL CAUTIONS Because next figures and sentences are very important, please understand these contents as follows. CAUTION This figure is a mark that you will get hurt and/or the module will have damages when you make a mistake to operate. This figure is a mark that you will get an electric shock when you make a mistake to operate. This figure is a mark that you will get hurt when you make a mistake to operate. CAUTION Do not touch an inverter - - on which is stuck a caution label - - while the LCD module is under the operation, because of dangerous high voltage. (1) Caution when taking out the module Pick the pouch only, in taking out module from a carrier box. (2) Cautions for handling the module a) As the electrostatic discharges may break the LCD module, handle the LCD module with care against electrostaic discharges. b) As the LCD panel and backlight element are made from fragile glass material, impulse and pressure to the LCD module should be avoided. c) As the surface of polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. d) Do not pull the interface connectors in or out while the LCD module is operating. e) Put the module display side down on a flat horizontal plane. f) Handle connectors and cables with care. g) When the module is operating, do not lose CLK, HS or Vsync signal. If any one of these signals is lost, the LCD panel would be damaged. h) The torque to mounting screw should never exceed 0.392 N·m (4 kgf·cm). (3) Cautions for the atmosphere a) Dew drop atmosphere should be avoided. b) Do not store and/or operate the LCD module in a high temperature and/or high humidity atmosphere. Storage in an electro-conductive polymer packing pouch and under relatively low temperature atmosphere, is recommended. c) This module uses cold cathod fluorescent lamps. Therefore, the life time of the lamps becomes short conspicuously at low temperature. d) Do not operate the LCD module in a high magnetic field. (4) Caution for the module characteristics a) Do not apply the fixed pattern for a long time to the LCD module at product againg. Applying fixed pattern for a long time may cause image sticking. 34 Data Sheet EN0444EJ1V0DS00 NL10276AC28-01L (5) Other cautions a) Do not disassemble and/or reassemble LCD module. b) Do not readjust any variable resistors, switches, etc. c) When returning the module for repair etc., please pack the module not to be broken. We recommend to the original shipping packages. Liquid Crystal Display has the following specific characteristics. There are neither defects nor malfunctions. The display condition of LCD module may be affected by the ambient temperature. The LCD module has cold cathode tube for backlight. Optical characteristics, like luminance or uniformity, will change during time. Uneven brightness and/or small spots may be noticed depending on different display patterns. Data Sheet EN0444EJ1V0DS00 35 5 200 ±0.3 5 4.5 4.7 13 13 94 13 · The torque for mounting screw should never 0.392 N · m (4 kg · cm). · Not shown tolerance of the dimension is ±0.5 mm. 80 φ 4.5 ±0.2 30 72 160 ±0.7 ACTIVE AREA CENTER 285.696 (ACTIVE AREA) 10.8 55 13 20 5 9.5 ±0.3 4.5 100 ±0.7 4– φ 3.5 ±0.2 92.8 MAX 19 TYP 17.8 Data Sheet EN0444EJ1V0DS00 16.2 32 ±0.3 200 ±0.3 4.5 MAX 20.5 TYP 19.8 4–2.7 ±0.3 219 ±0.3 (BEZEL OPENING) 4.5 255 ±0.5 36 5 330 ±0.5 320 ±0.3 290.4 ±0.3 (BEZEL OPENING) 4–3.4 ±0.3 NL10276AC28-01L OUTLINE DRAWINGS Front View (Unit in mm) 214.27 (ACTIVE AREA) 52 11.2 7 10.3 10.2 10.2 32 ±1 130 69.5 36.3 ±1 THE TFT COLOR LCD PANEL CONTAINS COLD CATHODE FLOURESCEST LAMPS. PLEASE FOLLOW LOCALORDINANCES OR REGULATIONS FOR ITS DISPOSAL 54 1.5 A 31 152 C 48.6 CN1 54.5 ±1 199 ±1 · The torque for mounting screw should never exceed 0.392N·m (4kgf·cm) · Not shown tolerance of the dimensions are ±0.5 mm. A Material Information Light guide: >PMMA< A 1 0 0 8 9 2 0 1 8 3 0 1 SERIAL: B9810036 PANEL: A100892018301 99.8.26/ C170832 MADE IN JAPAN MODEL: NL10276AC28-02L 1 231 20 10.3 153 ±1 FPC 109 10.3 3 18.3 2.7 ±0.3 3.4 ±0.3 MAX 19 TYP 17.8 10.3 24 11.3 6 1 30 100 30 14.3 14.3 7 117 ±1 11 1 CN201 1 14 CN4 CN3 CN5 1 25 8 1 16.2 8 13.8 13.2 8 Data Sheet EN0444EJ1V0DS00 16.2 165 233 MAX 20.5 TYP 19.8 NL10276AC28-01L Rear View (Unit in mm) CAUTION HIGH VOLTAGE 37 NL10276AC28-01L [MEMO] 38 Data Sheet EN0444EJ1V0DS00 NL10276AC28-01L [MEMO] Data Sheet EN0444EJ1V0DS00 39 1/ìíëæç$&ëåðíì/ No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its electronic components, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC electronic component, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. Anti-radioactive design is not implemented in this product. DATA SHEET