NJW1191 4-channel Electronic Volume with Input Selector !GENERAL DESCRIPTION !PACKAGE OUTLINE NJW1191 is 4-channel Electronic Volume with input selector. It includes main volume, balance and fader trim, 4 inputs selector, loudness and tone control. NJW1191 performs low noise and low distortion characteristics with resistance ladder type electrical volume. 2 All of internal status and variables are controlled by I C BUS interface. NJW1191V !FEATURES ●Operating Voltage ●I2C BUS Interface ●Low Output Noise ●Low Distortion ●4ch Input Selector ●Loudness ●Tone Control ●Main Volume ●Balance & Fader ●Bi-CMOS Technology ●Package Outline 7.5 to 13V -103dBVtyp 0.01%typ Bass / Treble SSOP32 Tone 0dB,+6dB ,+12dB,+18dB I2C Interface !BLOCK DIAGRAM Tone Bias 0dB,+6dB ,+12dB,+18dB –1– NJW1191 !PIN FUNCTION No. 32 17 1 16 SYMBOL FUNCTION No. SYMBOL FUNCTION 2 1 GND Ground 17 SDA 2 VREF Reference Voltage 18 RL_OUT Lch Rear Vol. Output 3 IN1R Rch Input 1 19 FL_OUT Lch Front Vol. Output 4 IN2R Rch Input 2 20 VOL2IN_L Lch 2nd Vol. Input 5 IN3R Rch Input 3 21 TONEOUT_L Lch Tone Output 6 IN4R Rch Input 4 22 DCCL Lch Tone Bass DC cut Capacitor 7 TAP1R Rch Loudness High Freq. Time Constant 23 TLCL Lch Tone Bass Time Constant 8 TAP2R Rch Loudness Low Freq. Time Constant 24 THCL Lch Tone Treble Time Constant 9 THCR Rch Tone Treble Time Constant 25 TAP2L Lch Loudness Low Freq. Time Constant 10 TLCR Rch Tone Bass Time Constant 26 TAP1L Lch Loudness High Freq. Time Constant 11 DCCR Rch Tone Bass DC cut Capacitor 27 IN4L Lch Input 4 12 TONEOUT_R Rch Tone Output 28 IN3L Lch Input 3 nd I C Data Input / Acknowledge Output 13 VOL2IN_R Rch 2 Vol. Input 29 IN2L Lch Input 2 14 FR_OUT Rch Front Vol. Output 30 IN1L Lch Input 1 15 RR_OUT Rch Rear Vol. Output 31 N.C No Connect 16 SCL I2C Clock Input 32 V+ Power Supply !ABSOLUTE MAXIMUM RATING (Ta=25°C) PARAMETER SYMBOL + RATING UNIT 15 800 V Supply Voltage V Power Dissipation PD NOTE: EIA/JEDEC STANDARD Test board (76.2x114.3x1.6mm, 2layer, FR-4) mounting Operating Temperature Range Topr -40 to +85 °C Storage Temperature Range Tstg -40 to +125 °C –2– mW NJW1191 !ELECTRICAL CHARACTERISTICS ( Ta=25°C, V+=9V, Rg=600Ω, RL=47kΩ, Vin=1.5Vrms,f=1kHz, all controls flat(Gv=0dB) unless otherwise specified) MIN. TYP. MAX. UNIT 7.5 9.0 13.0 V No Signal - 13 18 mA VREF No Signal 4.0 4.5 5.0 V VIM VOL1=-20dB THD=1% 2.0 2.4 - Vrms VOM1 THD=1% 2.0 2.4 - Vrms VOM2 THD=1%, f=50kHz 1.5 2.4 - Vrms Voltage Gain 1 GV1 VOL1=0dB, AMP GAIN=+18dB Vin=0.1Vrms +16 +18 +20 dB Voltage Gain 2 GV2 -1 0 1 dB Voltage Gain 3 GV3 VOL1=-68dB -71 -68 -65 dB Voltage Gain 4 GV4 VOL2FL,FR,BL,BR=-42dB -45 -42 -39 dB Mute Level Mute VOL2FL,FR,BL,BR=Mute Filter : 400Hz to 30kHz - -100 -90 dB Channel Balance GCB -1 0 1 dB Total Harmonic Distortion THD PARAMETER + Operating Voltage V Supply Current ICC Reference Voltage Maximum Input Voltage Maximum Output Voltage 1 Maximum Output Voltage 2 Condition SYMBOL Output Noise Voltage 1 VNO1 Output Noise Voltage 2 VNO2 BW : 400Hz to 30kHz - 0.01 0.05 % Rg=0Ω, Filter : A-weighted - -103 (7) -90 (32) - -108 (4) -95 (17.8) dBV (µVrms) dBV (µVrms) Unselected Input : Input signal Filter : 400Hz to 30kHz 90 100 - dB VOL2FL,FR,BL,BR=Mute Rg=0Ω, Filter : A-weighted Selected Input : No signal Rg=0Ω Cross Talk CT Channel Separation CS Rg=0Ω, Filter : 400Hz to 30kHz 90 100 - dB Maximum Low Boost Level GLDL Loudness=ON,VOL1=-24dB,f=40Hz 9.5 12 14.5 dB Maximum High Boost Level GLDH Loudness=ON,VOL1=-24dB,f=10kHz 2.5 5 7.5 dB Treble Boost Level GHBST BCT=”1”,TREB=”111”, f=10kHz Vin=0.1Vrms 11.5 14.0 16.5 dB Treble Flat Level GHFLT TREB=”000”,f=10kHz -2.0 0.0 2.0 dB Treble Cut Level GHCUT BCT=”0”,TREB=”111”, f=10kHz -16.5 -14.0 -11.5 dB Bass Boost Level GLBST BCB=”1”,BASS=”111”, f=100Hz Vin=0.1Vrms 11.5 14.0 16.5 dB Bass Flat Level GLFLT BASS=”000”,f=100Hz -2.0 0.0 2.0 dB Bass Cut Level GLCUT BCB=”0”,BASS=”111”, f=100Hz -16.5 -14.0 -11.5 dB ♦LOUDNESS ♦TONE –3– NJW1191 !I2C BUS BLOCK CHARACTERISTICS (SDA,SCL) PARAMETER SYMBOL MIN. TYP. MAX. UNIT High Level Input Voltage VIH 2.5 - 5.0 V Low Level Input Voltage VIL 0 - 1.5 V High Level Input Current IIH - - 10 µA Low Level Input Current IIL - - 10 µA Low Level Output Voltage (3mA at SDA pin) VOL 0 - 0.4 V Maximum Output Current IOL -3.0 - - mA Maximum Clock Frequency fSCL - - 100 kHz Data Change Minimum Waiting Time tBUF 4.7 - - µs tHD:STA 4.0 - - µs Low Level Clock Pulse Width tLOW 4.7 - - µs High Level Clock Pulse Width tHIGH 4.0 - - µs Minimum Start Preparation Waiting Time tSU:STA 4.7 - - µs Minimum Data Hold Time tHD:DAT 5.0 - - µs Minimum Data Preparation Time tSU:DAT 250 - - ns Rise Time tR - - 1.0 µs Fall Time tF - - 300 ns tSU:STO 4.0 - - µs Data Transfer Start Minimum Waiting Time Minimum Stop Preparation Waiting Time 2 I C BUS Load Condition: Pull up resistance 4kΩ (Connected to +5V) Load capacitance 200pF (Connected to GND) SDA tBUF tR tF tHD:STA SCL tHD:STA tLOW P –4– S tHD:DAT tHIGH tSU:STA tSU:DAT Sr tSU:STO P NJW1191 !APPLICATION CIRCUIT C25 1 V+ GND 32 BIAS C1 10µF 2 + +9V 31 VREF C2 1µF 30 3 + C3 1µF 5 + C5 1µF INPUT SELECTOR + C4 1µF INPUT SELECTOR 4 29 28 27 6 + C6 470pF MASTER VOLUME & LOUDNESS R1 39kΩ R2 4.7kΩ C8 4.7nF 8 1µF C22 + 1µF C21 + 1µF R8 39kΩ 25 TONE CONTROL C20 100nF R7 C19 4.7nF 4.7kΩ C18 100nF TONE CONTROL 23 C17 4.7µF + C10 4.7µF + C23 + 24 10 + 1µF 26 MASTER VOLUME & LOUDNESS 9 C9 100nF R3 2.2kΩ C24 + C21 470pF 7 C7 100nF 100µF + 11 22 12 21 C11 1µF R6 2.2kΩ + C16 1µF 13 C12 10µF + C13 10µF + 20 14 FRONT VOLUME FRONT VOLUME 19 15 REAR VOLUME REAR VOLUME 18 R4 100Ω 16 SCL I2C BUS INTERFACE C15 10µF + C14 10µF + R5 100Ω SDA 17 !APPLICATION NOTES Pin No. Function Note C1 can be adjusted rise and fall time of reference voltage at power on and off. Take care that the reduced C1makes sensitive to ripple of power supply. The Input impedance is designed about 48k ohms. The ground line should be inserted between each input lines to 3 - 6, 27 -30 Inputs avoid cross talk. Loudness frequency can be adjusted with external parts(See page 6) . Especialy, 8 and 25 pins should be kept from Loudness filter large signal lines such as digital signal lines or the other sound signal lines to avoid digitaly noise or cross talk in 7,8,25,26 Taps Loudness mode. Tone Bass and Treble cut off frequency can be adjusted with external parts(See page6). These pins should be kept 9,10,11,22,23, Tone filter from large signal lines such as digital signal lines or the other sound signal lines to avoid the digitaly noise or cross 24 terminals talk. 12,21 Tone outputs Output impedance is designed about 50 ohms. Balance Fedar Input impedance is designed about 24k ohms. 13,20 volume inputs Balance Fedar 14,15,18,19 volume Output impedance is designed about 50 ohms. outputs 2 VREF 16,17 I2C control signal ports These terminals should be inserted resistance about 100 ohms between terminal and signal source to reduce the digitaly noise. These lines should be kept from analog signal lines and or near by the chip to avoid digitaly noise. Inserted ground line between analog line and digital line should be recommended. –5– NJW1191 !APPLICATION NOTES < Loudness fc adjustment > Loudness High and Low Boost cut off frequencies are able to adjust with the external parts as shown in fig.A. They are given by the functions below. TAP1 (7, 26pin) High Boost cut off frequency: fcH= MASTER VOLUME & LOUDNESS Ce1 (C6, C21) Re1 (R1, R8) TAP2 (8, 25pin) Low Boost cut off frequency: fcL= 1 (Hz) 2πRe1 ⋅ Ce1 1 2πRe2 ⋅ Ce2 (Hz) Re2 (R2, R7) <NOTE> Re2 should be fixed to 4.7kΩ for the precise level of volume in Loudness mode. Ce2 (C7, C20) fig. A Loudness circuit < Tone fc adjustment > Tone High and Low cut off frequencies are able to adjust with the external parts as shown in fig.B. They are given by the functions below. . R3A Treble cut off frequency: fcT= R4A R3B (R3A+R3B = 33kΩ) THC (9, 24pin) Ce3 DCC (11, 22pin) Ce4 (C8, C19) Ce5 (C9, C18) Bass cut off frequency: fcBL= (C10, C17) Re3 (R3, R6) DC cut off frequency: fcDC= (Boost) R4A R3B (R +R = 33kΩ) 3A 3B R4B TLC (10, 23pin) Ce3 Ce5 (C9, C18) (C10, C17) Re3 (R3, R6) (Cut) fig. B –6– (R4A+R4B= 33kΩ) DCC (11, 22pin) Ce4 (C8, C19) (Hz) (R 4B + R e3 ) 2π (R 4A + R 4B ) ⋅ R e3 ⋅ C e4 1 2π (R 4B + R e3 ) ⋅ C e5 (Hz) (Hz) (R4B=3.3kΩ at 14dB set) R3A THC (9, 24pin) 2πR 3B ⋅ C e3 (R3B=5.5kΩ at 14dB set) R4B (R4A+R4B= 33kΩ) TLC (10, 23pin) 1 Tone circuit NJW1191 !TERMINAL DESCRIPTION No. SYMBOL FUNCTION EQUIVALENT CIRCUIT VOLTAGE V+ 200k 2 VREF Reference Voltage V+/2 200k GND V+ 3 4 5 6 30 29 28 27 IN1R IN2R IN3R IN4R IN1L IN2L IN3L IN4L Rch Input 1 Rch Input 2 Rch Input 3 Rch Input 4 Lch Input 1 Lch Input 2 Lch Input 3 Lch Input 4 V+/2 50 18k 30k VREF GND V+ 7 TAP1R 26 TAP1L Rch Loudness High Freq. Time Constant Lch Loudness High Freq. Time Constant V+/2 50 GND V+ 8 TAP2R 25 TAP2L Rch Loudness Low Freq. Time Constant Lch Loudness Low Freq. Time Constant 50 V+/2 VREF GND 4.7k VREF –7– NJW1191 !TERMINAL DESCRIPTION No. SYMBOL FUNCTION EQUIVALENT CIRCUIT VOLTAGE V+ 9 24 THCR THCL Rch Tone Treble Time Constant Lch Tone Treble Time Constant 5k 50 V+/2 1.8k GND V+ 10 23 TLCR TLCL 800 Rch Tone Bass Time Constant Lch Tone Bass Time Constant 6.7k 5.4k V+/2 50 GND V+ 11 DCCR 22 DCCL Rch Tone Bass DC cut Capacitor Lch Tone Bass DC cut Capacitor V+/2 3k 50 2k GND V+ 12 21 TONEOUT_R Rch Tone Output TONEOUT_L Lch Tone Output V+/2 50 3k 6k 7k GND –8– NJW1191 !TERMINAL DESCRIPTION No. SYMBOL FUNCTION EQUIVALENT CIRCUIT VOLTAGE V+ 70 13 20 VOL2IN_R VOL2IN_L 12k 2.5k nd Rch 2 Vol. Input nd Lch 2 Vol. Input V+/2 12k 70 2.5k GND V+ 14 15 19 18 FR_OUT RR_OUT RL_OUT FL_OUT Rch Front Vol. Output Rch Rear Vol. Output Lch Front Vol. Output Lch Rear Vol. Output 10k 10k GND VREF 16 SCL V+/2 50 2 4k I C Clock Input 12k GND 17 SDA 2 I C Data Input / Acknowledge Output 4k 12k GND –9– NJW1191 2 !DEFINITION OF I C REGISTER 2 ♦I C BUS FORMAT MSB S LSB Slave Address 1bit 8bit MSB LSB A Select Address 1bit 8bit MSB LSB A 1bit Data A P 8bit 1bit 1bit S: Starting Term A: Acknowledge Bit P: Ending Term ♦SLAVE ADDRESS Slave Address Hex MSB 1 0 0 0 0 0 0 LSB - 0 80(h) ♦CONTROL REGISTER TABLE The select address sets each function (Volume, Loudness, Balance, Fader, Tone Control, Input Selector). The auto increment function cycles the select address as follows. 00H→01H→02H→03H→04H→00H <Write Mode> Select Address 00H 01H 02H 03H 04H BIT D7 D6 D4 D5 Amp Gain VOL2FL (Front Left) VOL2RL (Rear Left) BCB Tone Bass FLMute FRMute RLMute D3 D2 D1 D0 VOL1 VOL2FR (Front Right) VOL2RR (Rear Right) BCT Tone Treble Input Selector Loudness RRMute Test * * Test : Set D0=0 in usually. (For device check use only) ♦CONTROL REGISTER DEFAULT VALUE Control register default value is all “0”. BIT Select Address D7 D6 D5 D4 D3 D2 D1 D0 00H 01H 02H 03H 04H 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 – 10 – NJW1191 !INSTRUCTION CODE a) MAIN VOLUME (VOL1,Amp Gain) SETTING Select Address BIT D7 00H D6 D5 D4 D3 Amp Gain D2 D1 D0 VOL1 •Amp Gain : 0dB, +6dB, +12dB, +18dB •VOL1 : Volume 1 Attenuator setting 0 to –30dB (1dB/Step),-30 to –68dB (2dB/Step),Mute b) BALANCE, FADER VOLUME (VOL2FL,FR,RL,RR ) SETTING Select Address BIT D7 D6 D5 D4 D3 D2 01H VOL2FL VOL2FR 02H VOL2RL VOL2RR D1 D0 D1 D0 •VOL2FL,FR,RL,RR : 0,-2,-4,-6,-8,-10,-12,-16,-18,-20,-24,-32,-34,-36,-38,-42 dB c) TONE SETTING BIT Select Address D7 03H BCB D6 D5 D4 D3 TONE BASS D2 BCT TONE TREBLE •BCB : Boost cut select for Bass control “0” : Cut “1” : Boost •TONE BASS : BASS Level Setting Cut Level : -14 to 0dB(2dB/Step) Boost Level : 0 to +14dB(2dB/Step) •BCT : Boost cut select for Treble control “0” : Cut “1” : Boost •TONE TREBLE : TREBLE Level Setting Cut Level : -14 to 0dB(2dB/Step) Boost Level : 0 to +14dB(2dB/Step) d) INPUT SELECTOR SETTING BIT Select Address D7 D6 D5 D4 04H FLMute FRMute RLMute RRMute D3 D2 Input Selector D1 D0 Loudness Test •FLMute, FRMute, RLMute, RRMute : VOL2FL,FR,RL,RR Mute •Input Selector: INPUT1 to 4 •Loudness : Loudness ON/OFF •Test : For device check use only. Set D0 = 0 in usual. – 11 – NJW1191 !VOL1(Select Address : 00H) VOL1 Gain(dB) D5 D4 D3 D2 D1 D0 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 -22 -23 -24 -25 -26 -27 -28 -29 -30 -32 -34 -36 -38 -40 -42 -44 -46 -48 -50 -52 -54 -56 -58 -60 -62 -64 -66 -68 Mute 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 – 12 – NJW1191 !AMP GAIN (Select Address : 00H) Gain(dB) 0 +6 +12 +18 AMP GAIN D7 D6 0 0 1 1 0 1 0 1 !VOL2 FL,FR (Select Address : 01H) VOL2 RL,RR (Select Address : 02H) : Front Channel : Rear Channel VOL2 Gain(dB) Lch D7 D6 D5 D4 Rch D3 D2 D1 D0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 -2 -4 -6 -8 -10 -12 -16 -18 -20 -24 -32 -34 -36 -38 -42 !TONE (Select Address : 03H) BCB Cut/Boost Select Cut Boost D7 BCT D3 0 1 TONE BASS D5 D4 TONE TREBLE D2 D1 D0 D6 Cut Boost Gain(dB) Gain(dB) -14 14 -12 12 -10 10 -8 8 -6 6 -4 4 -2 2 0 0 1 1 1 1 0 0 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 – 13 – NJW1191 !VOL2 MUTE (Select Address : 04H) Mute Setting Mute Active FL Mute D7 FR Mute D6 RL Mute D5 RR Mute D4 0 1 !INPUT SELECTOR (Select Address : 04H) Input Selector D3 D2 INPUT 1 INPUT 2 INPUT 3 INPUT 4 0 0 1 1 0 1 0 1 !LOUDNESS (Select Address : 04H) Loudness Loudness Setting D1 OFF ON 0 1 !TEST (Select Address : 04H) Test D0 Normal Test Mode – 14 – 0 1 * FOR DEVICE CHECK USE ONLY. NJW1191 ! TYPICAL CHARACTERISTICS Operating Current vs. Operating Voltage Operating Current vs. Ambient Temperature V+=9V 16 15 85°C 14 14 Operating Current [mA] Operating Current [mA] 12 13 12 11 10 8 25°C 6 -40°C 4 10 2 0 9 -50 0 50 100 0 150 5 Reference Voltage vs. Ambient Temperature V+=9V 4.7 10 15 Operating Voltage [V] Ambient Temperature [°C] PSRR vs. Frequency V+=9V+1Vrms 0 -10 -20 -30 -40 PSRR [dB] Reference Voltage [V] 4.6 4.5 -50 -60 -70 4.4 -80 -90 4.3 -50 0 50 100 -100 10 10 150 100 100 Ambient Temperature [°C] Maximum Input Voltage vs. Ambient Temperature Input : L1, Output : FL, VOL1=-20dB, THD=1% 10000 10K 100000 100K Maximum Output Voltage vs. Frequency Input : L1, Output : FL,RL, THD=1% 4.0 4.0 3.5 3.5 Maximum Output Voltage [Vrms] Maximum Input Voltage [Vrms] 1000 1K Frequency [Hz] 3.0 2.5 2.0 1.5 1.0 -40°C, 25°C 3.0 2.5 2.0 85°C 1.5 1.0 0.5 0.5 0.0 0.0 -50 0 50 100 Ambient Temperature [°C] 150 10 100 100 1K 1000 10K 10000 100K 100000 Frequency [Hz] – 15 – NJW1191 ! TYPICAL CHARACTERISTICS Maximum Output Voltage vs. Ambiemt TEmperature Input : L1, Output : FL, f=50kHz, THD=1% 4.0 4.0 3.5 3.5 Maximum Output Voltage [Vrms] Maximum Output Voltage [Vrms] Maximum Output Voltage vs. Ambient Temperature Input : L1, Output : FL, THD=1% 3.0 2.5 2.0 1.5 1.0 3.0 2.5 2.0 1.5 1.0 0.5 0.5 0.0 0.0 -50 0 50 100 -50 150 0 50 100 150 Ambient Temperature [℃] Ambient Temperature [℃] Voltage Gain vs. Frequency Input : L1, Output : FL, BW:10Hz-80kHz Voltage Gain vs. Frequency Input : L1, Output : FL, BW:10Hz-80kHz 40 40 20 20 0 0 -20 VOL1=0dB -40 VOL1=-68dB Voltage Gain [dB] Voltage GAin [dB] GAIN=+18dB -60 VOL2=0dB VOL2=-42dB -20 -40 -60 -80 VOL2=MUTE -80 -100 -100 VOL1=MUTE -120 10 10 -120 100 100 1K 1000 10K 10000 10 10 100K 100000 100 100 Frequnency [Hz] 1K 1000 10K 10000 100K 100000 Frequnency [Hz] Voltage Gain vs. Volume Set Level Input : L1, Output : FL, Control: VOL2 Voltage Gain vs. Volume Set Level Input : L1, Output : FL, Control: VOL1 -50 -80 -70 -40 -60 Voltage Gain [dB] -40°C, 25°C, 85°C Voltage Gain [dB] -40°C, 25°C, 85°C -50 -40 -30 -20 -30 -20 -10 -10 0 0 0 -10 -20 -30 -40 -50 Volume Set Level [dB] – 16 – -60 -70 0 -10 -20 -30 Volume Set Level [dB] -40 -50 NJW1191 ! TYPICAL CHARACTERISTICS THD+N vs. Input Voltage Input : L1, Output : FL, BW:10Hz-80kHz THD+N vs. Input Voltage Input : L1, Output : FL, BW:400Hz-30kHz 10 10 1 1 VOL1=-12dB VOL1=-18dB THD+N [%] THD+N [%] 20Hz 20kHz,50kHz 0.1 0.01 0.1 0.01 VOL1=-6dB 1kHz 0.001 0.01 0.1 VOL1=0dB 1 0.001 0.01 10 0.1 1 Input Voltage [Vrms] Input Voltage [Vrms] THD+N vs. Ambient Temperature Input : L1, Output : FL, BW:400-30kHz THD+N vs. Frequency Input : L1, Output : FL 10 1 10 0.1 0.1 Vin=1.5Vrms Vin=1Vrms THD+N [%] THD+N [%] 1 0.01 -40°C, 25°C 0.01 0.001 0.0001 -50 85°C Vin=0.5Vrms 0 50 100 150 0.001 10 10 100 25 Output Noise Voltage [µVrms] 10 THD+N [%] 100000 100K 30 100 25°C 85°C 0.1 0.01 20 15 VOL1=VOL2=0dB 10 5 -40°C 0.001 0.01 10000 10K Output Noise Voltage vs. Ambient Tempereture Input : L1, Output : FL, Rg=0Ω, A-w eighted THD+N vs. Input Voltage Input : L1, Output : FL, BW:400Hz-30kHz 1 1000 1K Frequency [Hz] Ambient Temperature [°C] VOL2=MUTE 0.1 1 Input Voltage [Vrms] 10 0 -50 0 50 100 150 Ambient Temperature[℃] – 17 – NJW1191 ! TYPICAL CHARACTERISTICS 120 110 110 100 100 90 90 Cross Talk [dB] 120 80 70 60 80 60 50 40 40 30 30 20 0 50 100 150 10 100 1000 Frequency [Hz] Channel Separation vs. Ambient Temperature Input : L1, Output : FL, Rg=0Ω, BW:400Hz-30kHz Channel Separation vs. Frequency Input : R1, Output : FL, Rg=0Ω, BW:10Hz-80kHz 120 110 110 100 100 90 90 80 70 60 50 70 60 50 40 30 30 20 0 50 100 10 10 150 1K 1000 100 Voltage Gain vs. Ambient Temperature (LOUDNESS) Input : L1, Output : FL, Loudness=ON, VOL1=-24dB 100K 100000 Voltage Gain vs. Frequency (LOUDNESS) Input : L1, Output : FL, Loudness=ON 5 14 VOL1=0dB 13 VOL1=-10dB 0 12 11 -5 f =40Hz 10 9 Voltage Gain [dB] Voltage Gain [dB] 10K 10000 frequency [Hz] Ambient Temperature [℃] 8 7 6 5 4 -10 -15 -20 -25 f =10kHz 3 2 VOL1=-20dB -30 1 VOL1=-30dB -35 0 50 Ambient Temperature [℃] – 18 – 100000 -40°C, 25°C, 85°C 80 40 0 -50 10000 Ambient Temperature[℃] 120 20 -50 -40°C, 25°C, 85°C 70 50 20 -50 Channel Separation [dB] Cross Talk vs. Frequency Input : L2,L3,L4, Output : FL, Rg=0Ω, BW:10Hz-80kHz Channel Separation [dB] Cross Talk [dB] Cross Talk vs. Ambient Temperature Input : L1, Output : FL, Rg=0Ω, BW:400Hz-30kHz 100 150 10 10 100 100 1000 1K 10000 10K Frequency [Hz] 100000 100K NJW1191 ! TYPICAL CHARACTERISTICS Voltage Gain vs. frequency (LOUDNESS) Input : L1, Output : FL, Loudness=ON, VOL1=-24dB Voltage Gain vs. Frequency (TONE) Input : L1, Output : FL 0 20 BASS=TREBLE=+14dB Ta=-40°C, 25°C, 85°C 15 -5 Voltage Gain [dB] Voltage Gain [dB] 10 -10 85°C -15 5 0 BASS=TREBLE=0dB Ta=-40°C, 25°C, 85°C -5 -10 -20 -15 -40°C -25 10 10 BASS=TREBLE=-14dB Ta=-40°C, 25°C, 85°C 25°C -20 100 1000 1K 10000 10K 100000 100K 10 100 100 Frequency [Hz] 10000 10K 100000 100K Voltage Gain vs. Frequency (TREBLE) Input : L1, Output : FL, Vin=0.1Vrms Voltage Gain vs. Frequency (BASS) Input : L1, Output : FL, Vin=0.1Vrms 20 20 TREBLE=+14dB BASS=+14dB 15 15 10 10 BASS=0dB Voltage Gain [dB] Voltage Gain [dB] 1000 1K Frequency [Hz] 5 0 -5 5 0 -5 -10 -10 -15 -15 TREBLE=0dB TREBLE=-14dB BASS=-14dB -20 -20 10 10 100 100 1000 1K 10000 10K 100000 100K 10 10 100 1K 1000 10K 10000 100K 100000 Frequency [Hz] Frequency [Hz] THD+N vs. Volume Set Level 10 THD+N [%] 1 20kHz 20Hz 0.1 0.01 1kHz 0.001 -80 -60 -40 -20 0 Volume Set Level [dB] – 19 – NJW1191 !NOTE [CAUTION] The specifications on this databook are only given for information , without any guarantee as regards either mistakes or omissions. The application circuits in this databook are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights. – 20 –