NTE309K Integrted Circuit Voltage Regulator Description: The NTE309K is a complete 5V regulator fabricated on a single silicon chip. It is designed for local regulation on digital logic cards, eliminating the distribution problems associated with single–point regulation. With the TO3 power package, the available output current is greater than 1A. The regulator is essentially blowout proof. Current limiting is included to limit the peak output current to a safe value. In addition, the thermal shutdown is provided to keep the IC from overheating. If internal dissipation becomes too great, the regulator will shut down to prevent excessive heating. Considerable effort was expended to make these devices easy to use and to minimize the number of external components. It is not necessary to bypass the output, although this does improve transient response somewhat. Input bypassing is needed, however, if the regulator is located very far from the filter capacitor of the power supply. Stability is also achieved by methods that provide very good rejection of load or line transients as are usually seen with TTL logic. Although designed primarily as a fixed–voltage regulator, the output can be set to voltages above 5V, as shown below. It is also possible to use the circuits as the control element in precision regulators, taking advantage of the good current–handling capability and the thermal overload protection. Features: D Specified to be compatible, worst case, with TTL and DTL D Output current in excess of 1A D Internal thermal overload protection D No external components required Absolute Maximum Ratings: Input Voltage, VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35V Power Dissipation, PD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internally Limited Operating Junction Temperature Range, Topr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +125°C Storage Temperature Range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to +150°C Typical Thermal Resistance, Junction–to–Case (Note 1), RthJC . . . . . . . . . . . . . . . . . . . . . . . 2.5°C/W Lead Temperature (Soldering, 10 seconds), TL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +300°C Note 1. Without a heat sink, the thermal resistance of the TO–3 package is approximately 35°C/W. With a heat sink, Electrical Characteristics: (Note 2) Parameter Test Conditions Min Typ Max Unit 4.8 5.05 5.2 V Output Voltage TJ = +25°C Line Regulation TJ = +25°C, 7 ≤ VIN ≤ 25V – 4.0 50 mV Load Regulation TJ = +25°C 5mA ≤ IOUT ≤ 1.5A – 15 100 mV Output Voltage 7 ≤ VIN ≤ 25V, 5mA ≤ IOUT ≤ IMAX, P ≤ PMAX 4.75 – 5.25 V Quiescent Current 7V ≤ VIn ≤ 25V – 5.2 10 mA Quiescent Current Change 7V ≤ VIN ≤ 25V – – 0.5 mA 5mA ≤ IOUT ≤ IMAX – – 0.8 mA TA = +25°C 10Hz ≤ f ≤ 100kHz – 40 – µV – – 20 mV 50 – – dB Output Noise Voltage Long Term Stability Ripple Rejection TJ = +25°C Note 2. Unless otherwise specified, these specifications apply 0°C ≤ TJ ≤ +125°C VIN = 10V; and IOUT = 0.5A. IMAX = 1.0A and PMAX = 20W. .135 (3.45) Max .350 (8.89) .875 (22.2) Dia Max Seating Plane Pin Connection Diagram Output .312 (7.93) Min .040 (1.02) 2 VOUT 1.187 (30.16) 1 .215 (5.45) .665 (16.9) Input Case/GND .156 (3.96) Dia (2 Holes) .430 (10.92) .188 (4.8) R Max VIN .525 (13.35) R Max GND/Case