NTE NTE7051

NTE7051
Integrated Circuit
1W BTL Mono Audio Amplifier
Description:
The NTE7051 is a mono output amplifier in a 8–Lead DIP style plastic package designed for use in
battery–fed portable audio applications, such as tape recorders and radios.
This device uses the Bridge–Tied–Load principle (BTL) which can deliver an output power of 1.2W
(THD = 10%) into an 8Ω load with a power supply of 6V. The load can be short–circuited at each signal
excursion.
Features:
D No External Components
D
No Switch–On or Switch–Off Clicks
D
Good Overall Stability
D
Low Power Consumption
D
No External Heatsink Required
D
Short–Circuit Proof
Absolute Maximum Ratings:
Supply Voltage, VP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18V
Non–Repetitive Peak Output Current, IOSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5A
Total Power Dissipation (TA = +25°C), Ptot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.15W
Operating Junction Temperature, TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Storage Temperature Range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65° to +150°C
Electrical Characteristics: (VP = 6V, RL = 8Ω, f = 1kHz, TA = +25°C unless otherwise specified)
Parameter
Symbol
Supply Voltage Range
VP
Total Quiescent Current
Itot
Voltage Gain
GV
Output Power
PO
Test Conditions
RL = ∞
THD = 10%
Min
Typ
Max
Unit
3
6
15
V
–
4
8
mA
39
40
41
dB
–
1.2
–
W
Electrical Characteristics (Cont’d): (VP = 6V, RL = 8Ω, f = 1kHz, TA = +25°C unless otherwise
specified)
Parameter
Symbol
Noise Output Voltage (RMS)
Vno(rms)
Frequency Response
Test Conditions
Min
Typ
Max
Unit
Note 1
–
150
300
µV
Note 2
–
60
–
µV
fr
20 to 20k
Hz
Supply Voltage Ripple Rejection
SVRR
Note 3
40
50
–
dB
DC Output Offset Voltage (Pin5 to Pin8)
∆V5–8
RS = 5kΩ
–
–
100
mV
Total Harmonic Distortion
THD
PO = 0.1W
–
0.2
–
%
Input Impedance
|ZI|
–
100
–
kΩ
Input Bias Current
Ibias
–
100
300
nA
Note 1. The unweighted RMS noise output voltage is measured at a bandwidth of 60Hz to 15kHz
with a source impedance (RS) of 5kΩ.
Note 2. The RMS noise output voltage is measured at a bandwidth of 5kHz with a source impedance
of 0Ω and a frequency of 500kHz. With a practical load (R = 8Ω, L = 200µH) the noise output
current is only 100nA.
Note 3. Ripple Rejection is measured at the output with a source impedance of 0Ω and a frequency
between 100Hz and 10kHz. The ripple voltage = 200mV (RMS value) is applied to the positive supply rail.
Pin Connection Diagram
VCC 1
8
Output 2
Input
2
7
N.C.
GND (Signal)
3
6
GND (Substrate)
N.C.
4
5
Output 1
8
5
.256 (6.52) Max
1
4
.393 (10.0)
Max
.300
(7.62)
.150
(3.81)
.100 (2.54)
.070 (1.77) Min
.300 (7.62)