(888) IPD-CONVerters ● (888) 473-2668 ● www.ipdconverters.com HPT SERIES - TRIPLE OUTPUT, 15 WATT DESCRIPTION FEATURES HPT triple output DC/DC converters provide 15 Watts of output power in an industry standard package. HPT’s feature excellent efficiency and industry-leading power density. The HPT has openframe packaging to provide maximum useable power with minimal thermal constraints. These units are fully compatible with production board washing processes. • • • • Triple Output 2” X 2” Open-Frame Packaging 2.5 Million Hours MTBF Short Circuit and Overvoltage Protection • 500V Isolation • Input Undervoltage Lockout • 3-1 Wide Voltage Input • 100°C Baseplate Operation TECHNICAL SPECIFICATIONS Input Voltage Range 24 VDC Nominal 48 VDC Nominal 48 VDC Wide 10 - 30 VDC 34 - 75 VDC 20 - 60 VDC Output Setpoint Accuracy Auxiliary Setpoint Accuracy Line Regulation Vin Min. - Vin Max., Iout Rated Load Regulation Iout Min. - Iout Max., Vin Nom. Minimum Output Current Dynamic Regulation, Loadstep Pk Deviation Settling Time Ripple and Noise w/ 25 MHz BW, Pk-Pk / RMS Current Limit Type Current Limit Threshold Range, % of Iout Rated Short Circuit Current Max. OVP Trip Range OVP Type ±1% 5% ±1% Vout ±1% Vout 10 % Iout Rated 25% Iout 1% Vout 250 µs 1% / 0.3% Vout Hiccup 110 - 140% 200% Iout Nom. 110 - 140% Vout Nom. Second Control Loop General Switching Frequency Isolation Input - Output Input - Case Output - Case Temperature Coefficient Case Temperature Operating Range Storage Range Thermal Shutdown Range Humidity Max., Non-Condensing Vibration, 3 Axes, 5 Min Each MTBF† (Bellcore TR-NWT-000332) Safety Weight (approx.) 200 kHz 500 VDC 500 VDC 500 VDC 0.02 ppm/°C -40 to +100°C -40 to +125°C 105 to 115°C 95% 2g 2.5 x 106 hrs Consult Factory 0.85 oz 1 Notes 1 For negative logic, add suffix “N” to model number. † MTBF predictions may vary slightly from model to model. Specifications typically at 25°C, normal line, and full load, unless otherwise stated. Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with commercial wave-soldering equipment. Safety: Agency approvals may vary from model to model. Please consult factory for specific model information. Units are water-washable and fully compatible with commercial spray or immersion post wave-solder washing equipment. HPT SERIES - TRIPLE OUTPUT, 15 WATT MODELS - (See the last page of this file for options.) Vin (Volts) Vin Range (Volts) Iin Max.* (Amps) Vout (Volts) Iout Rated (Amps) 24 24 24 24 48 48 48 48 48 WIDE 48 WIDE 48 WIDE 48 WIDE 18 - 36 18 - 36 18 - 36 18 - 36 34 - 75 34 - 75 34 - 75 34 - 75 20 - 60 20 - 60 20 - 60 20 - 60 1.90 1.90 1.84 1.84 0.56 0.56 0.54 0.54 0.95 0.95 0.92 0.92 3.3, –12 3.3, –15 5, –12 5, –15 3.3, –12 3.3, –15 5, –12 5, –15 3.3, –12 3.3, –15 5, –12 5, –15 2.3, 2.3, 1.5, 1.5, 2.3, 2.3, 1.5, 1.5, 2.3, 2.3, 1.5, 1.5, Ripple & Noise Pk-Pk (mV) 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, –0.31 –0.25 –0.31 –0.25 –0.31 –0.25 –0.31 –0.25 –0.31 –0.25 –0.31 –0.25 –200 –200 –200 –200 –200 –200 –200 –200 –200 –200 –200 –200 Efficiency Typ. ** Model HPT015YEHH-A HPT015YEJJ-A HPT015YGHH-A HPT015YGJJ-A HPT015ZEHH-AS1 HPT015ZEJJ-AS1 HPT015ZGHH-AS1 HPT015ZGJJ-AS1 HPT015ZEHH-A HPT015ZEJJ-A HPT015ZGHH-A HPT015ZGJJ-A 80% 80% 83% 83% 80% 80% 83% 83% 80% 80% 83% 83% Denotes advanced product release. Consult factory for product availability. * Maximum input current at minimum input voltage, maximum rated output power. ** At nominal Vin, rated output. MECHANICAL DRAWING 2.00" 0.18" (50.8mm) 0.700"(17.8mm) 0.500"(12.7mm) (4.6mm) 3 1.200"(30.5mm) 4 0.800"(20.3mm) 1 2 DIA 0.040" (1.0mm) 2.00" (50.8mm) BOTTOM VIEW 5 0.400"(10.2mm) 6 0 -0.40"(-10.2mm) 0.025" REF. 0 1.800"(45.7mm) (0.6mm) -0.10"(-2.5mm) Thermal Impedance Natural Convection 100 LFM 200 LFM 300 LFM 400 LFM 11.2 9.6 6.8 5.1 4.2 °C/W °C/W °C/W °C/W °C/W Note: Thermal impedance data is dependent on many environmental factors. The exact thermal performance should be validated for specific application. Pin Function 1 2 3 4 5 6 +Vin -Vin +V out +V out -V out -V out 2 0.40" (10.2mm) Tolerances Inches: .XX ± 0.020 .XXX ± 0.010 Pin: ± 0.002 (Millimeters) .X ± 0.5 .XX ± 0.25 ± 0.05 (Dimensions as listed unless otherwise specified.) OPTIONS When ordering equipment options, use the following suffix information. Select the option(s) that you prefer and add them to the model number. Example ordering options are located below the options table. OPTION SUFFIX APPLICABLE SERIES Negative Logic N HAS, HBD, HBS, HES, LES, QBS, QES, TES, TQD Lucent Compatible Trim T HAS, HBD, HBS, HES, QBS, QES Terminal Strip TS REMARKS TTL “Low” Turns Module ON TTL “High” Turns Module OFF XWS, XWD, XWT Trim 1 IAS, LES Enable 2 IAD, IAS, LES, SMS Trim and Enable 3 IAS, LES Current Share 4 SMS Headerless Y Encapsulated EWS, IWS, OWS PIN LENGTH AND HEATSINK OPTIONS Standard Pin Length is 0.180” (4.6mm) 0.110” (2.8mm) Pin Length 8 All Units (Except SMS) 0.150” (3.8mm) Pin Length 9 All Units (Except SMS) 0.24” (6.1mm) Horizontal Heatsink 1H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.24” (6.1mm) Vertical Heatsink 1V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.45” (11.4mm) Horizontal Heatsink 2H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.45” (11.4mm) Vertical Heatsink 2V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.95” (24.1mm) Horizontal Heatsink 3H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.95” (24.1mm) Vertical Heatsink 3V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad Example Options:HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent compatible trim, and 0.95” vertical heatsink. LES015YJ-3N = LES015YJ with optional trim and enable, negative logic. QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110” pin length. NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc. TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. 3