(888) IPD-CONVerters ● (888) 473-2668 ● www.ipdconverters.com QBS SERIES - 120 WATT Rev. 04/2001 DESCRIPTION FEATURES QBS single output DC/DC converters provide up to 120 Watts of output power in an industry standard, quarter-brick footprint. The QBS converters feature open-frame packaging, along with planar magnetics to provide maximum useable power with minimal thermal constraints. The QBS is especially suited to telecom, networking, and industrial applications, and is fully compatible with production board washing processes. • “Quarter-Brick” • High Power Density Up To 120W • Open-Frame Packaging • 100°C Baseplate Operation • Water Washable • Outputs From 2.5V to 15V • 1500V Isolation • Positive or Negative Enable Logic TECHNICAL SPECIFICATIONS Input Voltage Range 24 VDC Nominal 48 VDC Nominal Input Reverse Voltage Protection 18 - 36 VDC 36 - 75 VDC Shunt Diode Output Dynamic Regulation, Loadstep Pk Deviation Settling Time Voltage Trim Range Short Circuit And Overcurrent Protection Current Limit Threshold Range, % of Iout Rated Short Circuit Current Limit OVP Trip Range UVP Trip Range OVP/UVP Type ±1% 0.2% Vout 0.5% Vout 0.5 VDC 10 % lout Rated 25% Iout 4% Vout 500 µs ±10% Shutdown 110 - 140% 200% I out 115 - 140% Vout Nom. 70 - 90% Vout Nom. Latching Efficiency vs. Load (48V Input) 90 85 EFFICIENCY % Setpoint Accuracy Line Regulation Vin Min. - Vin Max., Iout Rated Load Regulation Iout Min. - Iout Max., Vin Nom. Remote Sense Headroom Minimum Output Current 80 QBS100ZG-ANT 75 EFF. (36v) EFF. (48v) 70 EFF. (75v) 65 60 10 20 30 40 50 60 LOAD% 70 80 90 100 General Turn-On Time Remote Shutdown Remote Shutdown Reference Switching Frequency Isolation Input - Output Input - Case Output - Case Temperature Coefficient Case Temperature Operating Range Storage Range Thermal Shutdown Range Vibration, 3 Axes, 5 Min Each MTBF† (Bellcore TR-NWT-000332) Safety Weight (Approx.) 30 ms Positive or Negative Logic Vin Negative 400 kHz 1500 VDC 1050 VDC 1050 VDC 0.02 ppm/°C -40°C To +100°C -40°C To +125°C 105°C To 115°C 5 g, 10 - 55 Hz 2.5 X 106 hrs UL, CUL, TUV 1.7 oz 1 Notes † MTBF predictions may vary slightly from model to model. Specifications typically at 25°C, normal line, and full load, unless otherwise stated. Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with commercial wave-soldering equipment. Safety: Agency approvals may vary from model to model. Please consult factory for specific model information. Units are water-washable and fully compatible with commercial spray or immersion post wave-solder washing equipment. QBS SERIES - 120 WATT MODELS - (See the last page of this file for options.) Vin (Volts) Vin Range (Volts) Iin Max.* (Amps) Vout (Volts) Iout Rated (Amps) Ripple & Noise Pk-Pk (mV) Efficiency Typ. ** 24 24 24 24 24 48 48 48 48 48 48 48 48 48 18 - 36 18 - 36 18 - 36 18 - 36 18 - 36 36 - 75 36 - 75 36 - 75 36 - 75 36 - 75 36 - 75 36 - 75 36 - 75 36 - 75 2.90 3.50 5.20 6.80 6.80 1.40 1.70 2.50 3.30 4.00 3.30 2.50 3.45 4.00 2.5 3.3 5 12 15 2.5 3.3 5 12 12 15 3.3 5.0 15 15.00 15.00 15.00 8.33 6.67 15.00 15.00 15.00 8.33 10.00 6.67 20.0 20.0 8.0 100 100 100 150 150 100 100 100 150 150 150 100 100 150 76% 80% 84% 85% 85% 75% 78% 83% 86% 84% 86% 80% 82% 84% Model QBS038YD-A QBS050YE-A QBS075YG-A QBS100YH-A † QBS100YJ-A QBS038ZD-A QBS050ZE-A QBS075ZG-A QBS100ZH-A † QBS120ZH-A † QBS100ZJ-A QBS066ZE-A † QBS100ZG-A † QBS120ZJ-A † † Denotes advanced product release. Consult factory for product availability. * Maximum input current at minimum input voltage, maximum rated output power. ** At nominal Vin, rated output. MECHANICAL DRAWING 2.28" (57.9mm) MOUNTING INSERTS M3X0.5 THROUGH 4PL 0.815"(20.7mm) 2 BOTTOM VIEW 3 5 0.450"(11.4mm) 6 0.300"(7.6mm) 7 0.150"(3.8mm) 8 0 -0.215"(-5.5mm) -0.425"(-10.8mm) -0.14" (-3.6mm) Thermal Impedance Natural Convection 100 LFM 200 LFM 300 LFM 400 LFM 10.1 8.0 5.4 4.4 3.4 (49.0mm) Pin °C/W °C/W °C/W °C/W °C/W Note: Thermal impedance data is dependent on many environmental factors. The exact thermal performance should be validated for specific application. 0.50" (12.7mm) 1.930" (1.8mm) (1.0mm) 6PL (4.6mm) (50.8mm) 0.070" DIA 0.040" 0.18" 2.000" 0 QBS 1.45" (36.8mm) 2PL 0.600"(15.2mm) 4 1 DIA 0.062" (1.6mm) Tolerances Function 1 2 3 4 5 6 7 8 -Vin On/Off +Vin -V out -Sense Trim +Sense +V out 2 Inches: .XX ± 0.020 .XXX ± .010 (Millimeters) .X ± 0.5 .XX ± 0.25 Pin: ± 0.002 ± 0.05 ( Dimensions as listed unless otherwise specified.) OPTIONS When ordering equipment options, use the following suffix information. Select the option(s) that you prefer and add them to the model number. Example ordering options are located below the options table. OPTION SUFFIX APPLICABLE SERIES Negative Logic N HAS, HBD, HBS, HES, LES, QBS, QES, TES, TQD Lucent Compatible Trim T HAS, HBD, HBS, HES, QBS, QES Terminal Strip TS REMARKS TTL “Low” Turns Module ON TTL “High” Turns Module OFF XWS, XWD, XWT Trim 1 IAS, LES Enable 2 IAD, IAS, LES, SMS Trim and Enable 3 IAS, LES Current Share 4 SMS Headerless Y Encapsulated EWS, IWS, OWS PIN LENGTH AND HEATSINK OPTIONS Standard Pin Length is 0.180” (4.6mm) 0.110” (2.8mm) Pin Length 8 All Units (Except SMS) 0.150” (3.8mm) Pin Length 9 All Units (Except SMS) 0.24” (6.1mm) Horizontal Heatsink 1H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.24” (6.1mm) Vertical Heatsink 1V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.45” (11.4mm) Horizontal Heatsink 2H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.45” (11.4mm) Vertical Heatsink 2V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.95” (24.1mm) Horizontal Heatsink 3H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.95” (24.1mm) Vertical Heatsink 3V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad Example Options:HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent compatible trim, and 0.95” vertical heatsink. LES015YJ-3N = LES015YJ with optional trim and enable, negative logic. QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110” pin length. NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc. TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. 3