VISHAY MKP3366Y2

MKP 336 6 Y2
Vishay BCcomponents
Interference Suppression Film Capacitors
MKP Radial Potted Type
FEATURES
168x12(halfpage)
10 to 15 mm lead pitch.
Supplied loose in box, taped on reel
w
l
e3
Lead (Pb)-free product
h
RoHS
RoHS-compliant product
COMPLIANT
PERMISSIBLE DC VOLTAGE
DC 1000 V
lt
Ø dt
P ± 0.4
Dimensions in mm
NO FOCUS PRODUCT: USE MKP 338 6 Y2
ENCAPSULATION
Plastic case, epoxy resin sealed, flame retardant UL-class
94 V - 0
APPLICATIONS
CLIMATIC TESTING CLASS ACC. TO EN 60068-1
Y2 class
55/105/56/B
For Y2 electromagnetic interference suppression between
line and ground applications (50/60 Hz) with a maximum
mains voltage of 300 Vac.
CAPACITANCE RANGE (E12 SERIES)
For application limitations refer to section
“APPLICATION NOTES”
E12 series 0.001 to 0.047 µF
Preferred values acc. to E6
CAPACITANCE TOLERANCE
REFERENCE STANDARDS
“IEC 60384-14 2nd edition and EN 132400”
“IEC 60065 requires, pass. flamm. class B”
250 V: UL 1414; CSA-C22.2 No 1;
300 V: UL1283; ENEC
± 20 %; ± 10 %
LEADS
Tinned wire
MARKING
C-value; tolerance; rated voltage; sub-class; manufacturer’s
type designation; code for dielectric material; manufacturer
location; year and week
DIELECTRIC
Polypropylene film
MAXIMUM APPLICATION TEMPERATURE
105 °C
DETAIL SPECIFICATION
For more detailed data and test requirements contact:
[email protected]
ELECTRODES
Metallized film
CONSTRUCTION
Series and triple construction
RATED VOLTAGE
AC 300 V; 50 to 60 Hz
Document Number: 28115
Revision: 12-Jul-07
For technical questions, contact: [email protected]
www.vishay.com
171
MKP 336 6 Y2
Vishay BCcomponents Interference Suppression Film Capacitors
MKP Radial Potted Type
COMPOSITION OF CATALOG NUMBER
TYPE AND PITCHES
336 6
10.0 mm
Y2
15.0 mm
MULTIPLIER
(nF)
CAPACITANCE
(numerically)
0.1
2
1
3
Example:
103 = 10 x 1 = 10 nF
BFC2 336 6X XX X
2222(*) 336 6X XX X
(*) Old ordering code
TYPE
PACKAGING
336 6
loose in box
Y2
LEAD CONFIGURATION
lead length 3.5 + 1/- 0.5 mm (pitch = 10 mm) or
3.5 ± 0.3 mm (pitch = 15 mm)
C-TOL
PREFERRED TYPES
BFC2 336 60...
± 20 %
BFC2 336 66...
lead length 25.0 ± 2.0 mm
ON REQUEST
336 6
loose in box
lead length 3.5 + 1/- 0.5 mm (pitch = 10 mm) or
3.5 ± 0.3 mm (pitch = 15 mm)
BFC2 336 61...
± 10 %
lead length 25.0 ± 2.0 mm
Y2
taped on reel (1)
H = 18.5 mm; P0 = 12.7 mm;
reel diameter 500 mm
BFC2 336 67...
± 20 %
BFC2 336 63...
± 10 %
BFC2 336 64...
Note:
(1) For detailed tape specification refer to Packaging information: www.vishay.com/docs/28139/packinfo.pdf
SPECIFIC REFERENCE DATA MKP 336 6 300 VAC
DESCRIPTION
VALUE
at 10 kHz
Tangent of loss angle:
≤ 10 × 10 -4
Rated voltage pulse slope (dU/dt)R at 420 V (DC)
200 V/µs
R between leads, for C ≤ 0.33 µF at 100 V; 1 minute
> 15 000 MΩ
R between leads and case; 100 V; 1 minute
> 30 000 MΩ
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s
3400 V; 1 minute
Withstanding (AC) voltage between leads and case
2100 V; 1 minute
www.vishay.com
172
For technical questions, contact: [email protected]
Document Number: 28115
Revision: 12-Jul-07
MKP 336 6 Y2
Interference Suppression Film Capacitors Vishay BCcomponents
MKP Radial Potted Type
MKP 336 6 GENERAL DATA
URac = 300 V; C-tol = ± 20 %
CATALOG NUMBER BFC2 336 6..... AND PACKAGING
LOOSE IN BOX
C
(µF)
DIMENSIONS
WxHxL
(mm)
MASS
(g)(1)
Lt = 3.5 + 1/- 0.5 mm (10 mm)
or 3.5 ± 03 mm (= 15 mm)
Last 5 digits of
catalog number
SPQ
REEL
H = 18.5 mm;
P0 = 12.7 mm
lt = 25.0 ± 2.0 mm
Last 5 digits of
catalog number
SPQ
Last 5 digits of
catalog number
SPQ
Pitch = 10.0 ± 0.4 mm; dt = 0.6 ± 0.06 mm
0.001
0.0015
0.0022
4.0 x 10.0 x 12.5
0.6
0.0033
0.0047
0.0068
60102
66102
60152
66152
60222
66222
60332
5.0 x 11.0 x 12.5
0.82
1000
63102
1250
66332
60472
66472
60682
66682
63152
63222
1400
63332
1000
63472
63682
1100
Pitch = 15.0 ± 0.4 mm; dt = 0.6 ± 0.06 mm
0.0068
0.01
0.015
5.0 x 11.0 x 17.5
1.0
6.0 x 12.0 x 17.5
1.4
69005
60103
69009
1000
60153
66103
69006
1000
66153
63103
1100
63153
900
63223
800
63333
650
63473
600
Pitch = 15.0 ± 0.4 mm; dt = 0.8 ± 0.08 mm
0.022
7.0 x 13.5 x 17.5
1.8
60223
0.033
8.5 x 15.0 x 17.5
2.4
60333
0.047
10.0 x 16.5 x 17.5
3.0
60473
750
500
66223
66333
66473
500
450
Notes
(1) Weight for short lead product only.
Document Number: 28115
Revision: 12-Jul-07
For technical questions, contact: [email protected]
www.vishay.com
173
MKP 336 6 Y2
Vishay BCcomponents Interference Suppression Film Capacitors
MKP Radial Potted Type
MKP 336 6 GENERAL DATA
URac = 300 V; C-tol = ± 10 %
CATALOG NUMBER BFC2 336 6..... AND PACKAGING
LOOSE IN BOX
C
(µF)
DIMENSIONS
WxHxL
(mm)
MASS
(g)(1)
Lt = 3.5 + 1/- 0.5 mm (10 mm)
or 3.5 ± 03 mm (= 15 mm)
Last 5 digits of
catalog number
SPQ
REEL
H = 18.5 mm;
P0 = 12.7 mm
lt = 25.0 ± 2.0 mm
Last 5 digits of
catalog number
SPQ
Last 5 digits of
catalog number
SPQ
Pitch = 10.0 ± 0.4 mm; dt = 0.6 ± 0.06 mm
0.001
61102
67102
64102
0.0012
61122
67122
64122
0.0015
61152
67152
64152
0.0018
61182
67182
0.0022
4.0 x 10.0 x 12.5
0.6
61222
1000
67222
1250
64182
64222
0.0027
61272
67272
64272
0.0033
61332
67332
64332
0.0039
61392
67392
64392
0.0047
61472
67472
0.0056
5.0 x 11.0 x 12.5
1.1
61562
1000
67562
1000
64472
64562
1400
1100
Pitch = 15.0 ± 0.4 mm; dt = 0.80 ± 0.08 mm
0.0056
69001
0.0068
0.0082
69007
61682
5.0 x 11.0 x 17.5
1.0
61822
69003
67682
1000
67822
64682
1000
64822
0.01
61103
67103
64103
0.012
61123
67123
64123
0.015
61153
67153
6.0 x 12.0 x 17.5
1.4
0.018
Pitch = 15.0 ± 0.4 mm; dt = 0.80 ± 0.08 mm
61183
0.022
61223
0.027
0.033
0.039
0.047
7.0 x 13.5 x 17.5
1.8
8.5 x 15.0 x 17.5
2.4
10.0 x 16.5 x 17.5
3.0
61273
1000
61473
1000
67223
750
61333
61393
67183
67273
64223
500
67333
500
67393
67473
61153
64183
64273
64333
450
61393
64473
1100
900
800
650
600
Notes
(1) Weight for short lead product only.
www.vishay.com
174
For technical questions, contact: [email protected]
Document Number: 28115
Revision: 12-Jul-07
MKP 336 6 Y2
Interference Suppression Film Capacitors Vishay BCcomponents
MKP Radial Potted Type
SAFETY APPROVALS Y2
VOLTAGE
VALUE
FILE NUMBERS
EN132400
300 V (AC)
1 nF to 47 nF
FI 2006018
250 V (AC)
1 nF to 47 nF
E112471
300 V (AC)
1 nF to 47 nF
E109565
UL1414 and CSA-C 22.2 No 1
antenna coupling
UL1283
The Enec-approval together with the CB-Certificate replace all national marks of the following countries (they have already signed the
ENEC-Agreement): Austria; Belgium; Czech. Republic; Denmark; Finland; France; Germany; Greece; Hungary; Ireland; Italy; Luxembourg;
Netherlands; Norway; Portugal; Slovenian; Spain; Switzerland and United Kingdom.
16
MOUNTING
Normal Use
The capacitors are designed for mounting on printed-circuit
boards. The capacitors packed in bandoliers are designed
for mounting in printed-circuit boards by means of automatic
insertion machines.
Specific Method of Mounting to Withstand Vibration and
Shock
In order to withstand vibration and shock tests, it must be
ensured that the stand-off pips are in good contact with the
printed-circuit board:
• The capacitors shall be mechanically fixed by the leads
Space Requirements on printed Circuit Board
The maximum length and width of film capacitors is shown in
Figure:
• Eccentricity as in figure. The maximum eccentricity is
smaller than or equal to the lead diameter of the product
concerned
• Product height with seating plane as given by “IEC 60717”
as reference: hmax ≤ h + 0.3 mm
Document Number: 28115
Revision: 12-Jul-07
bmax = b + 0.3 mm
eccentricity
lmax = I + 0.3 mm
CBA116
Storage Temperature
• Storage temperature: Tstg = 25 to + 40 °C with RH
maximum 80 % without condensation
Ratings and Characteristics Reference Conditions
Unless otherwise specified, all electrical values apply to an
ambient temperature of 23 ± 1 °C, an atmospheric pressure
of 86 to 106 kPa and a relative humidity of 50 ± 2 %.
For reference testing, a conditioning period shall be applied
over 96 ± 4 hours by heating the products in a circulating air
oven at the rated temperature and a relative humidity not
exceeding 20 %.
For technical questions, contact: [email protected]
www.vishay.com
175
MKP 336 6 Y2
Vishay BCcomponents Interference Suppression Film Capacitors
MKP Radial Potted Type
CHARACTERISTICS
Capacitance
Tangent of loss angle
4
2
3
Dissipation
Factor (x 10- 4)
ΔC/C
(%)
10
typical
10 2
0
-2
F
47 n
C≤
<
F
10 n ≤ 10 nF
C
101
-4
min.
-6
10
0
- 50
50
Tamb (°C) 100
Impedance
0
10
1
10
2
10
3
10
4
f (Hz) 10 5
Resonant frequency
103
4.7
10
47
1
102
F
f (MHz)
Impedance
(Ω)
1n
nF
nF
nF
10
101
100
10-1
10-2
104
105
106
107
f (Hz) 108
100
C (nF)
10
1
47
Max RMS voltage and AC current (sinewave)
3
10 3
AC current
(mA)
AC voltage
(V)
10
47 nF
102
10 1
10 nF
4.7 nF
10 0
1nF
Tamb ≤ 105 °C
Tamb ≤ 105 °C
-1
101
10
1
10
www.vishay.com
176
2
10
3
10
4
10
f (Hz) 105
10 1
For technical questions, contact: [email protected]
10 2
10 3
104
f (Hz) 105
Document Number: 28115
Revision: 12-Jul-07
MKP 336 6 Y2
Interference Suppression Film Capacitors Vishay BCcomponents
MKP Radial Potted Type
Insulation resistance
6
RC (s)
10
5
10
4
10
0
20
40
60
80 T
100
amb(°C)
APPLICATION NOTES
• For Y2 electromagnetic interference suppression between line and ground (50/60 Hz) with a maximum mains voltage of
300 V (AC) ± 10 % instability.
• These capacitors are not intended for continuous pulse applications. For these situations, capacitors of the AC and pulse
program must be used.
• The maximum ambient temperature must not exceed 105 °C.
• Rated voltage pulse slope:
If the pulse voltage is lower than the rated voltage, the values of the specific reference data can be multiplied by 420 V (DC)
and divided by the applied voltage.
Document Number: 28115
Revision: 12-Jul-07
For technical questions, contact: [email protected]
www.vishay.com
177
MKP 336 6 Y2
Vishay BCcomponents Interference Suppression Film Capacitors
MKP Radial Potted Type
INSPECTION REQUIREMENTS
General Notes:
1. Sub-clause numbers of tests and performance requirements refer to the “ Sectional Specification, IEC-puplication EN 132400
(IEC 60384-14) and section One of this specification”.
2. In this table: D =destructive
ND = non destructive
Group C inspection requirements
SUB - CLAUSE NUMBER
AND TEST
D
OR
ND
CONDITIONS
PERFORMANCE REQUIREMENTS
Group C inspection (periodic) see section “General notes“ item 3
SUB-GROUP C1A PART OF SAMPLE
OF SUB-GROUP C1
D
4.1 Dimensions (detail)
As specified in Chapters “General data”
of this specification
Initial measurements
Capacitance
Tangent of loss angle at 10 kHz
4.3 Robustness of
terminations
Tensile: load 10 N; 10 s
Bending: load 5 N; 4 x 90°
4.4 Resistance to soldering heat
No pre-drying
Method: 1A
Solder bath: 260 °C
Duration: 10 s
4.19 Component solvent
resistance
Isopropylalcohol at room temperature
Method: 2
Immersion time: 5 ± 0.5 min
Recovery time:
Min 1 hour, max 2 hours
4.4.2 Final measurements
Visual examination
No visible damage
Legible marking
Capacitance
|ΔC/C| ≤ 5 % of the value measured
initially
Tangent of loss angle
Increase of tan δ:
≤ 0.008
Compared to values measured initially
Insulation resistance
As specified in Section
“Insulation
Resistance” of this specification
SUB - GROUP C1B PART OF SAMPLE
OF SUB - GROUP C1
D
Initial measurements
Capacitance
Tangent of loss angle at 10 kHz
4.20 Solvent resistance of the marking:
see Section “General notes”; item 5
Isopropylalcohol at room temperature
Method: 1
Rubbing material: cotton wool
Immersion time: 5 ± 0.5 min
4.6 Rapid change of temperature
θA = - 55 °C
θB = + 105 °C
5 cycles
4.6.1 Inspection
Duration t = 30 min
www.vishay.com
178
No visible damage
For technical questions, contact: [email protected]
No visible damage
Legible marking
Document Number: 28115
Revision: 12-Jul-07
MKP 336 6 Y2
Interference Suppression Film Capacitors Vishay BCcomponents
MKP Radial Potted Type
SUB - CLAUSE NUMBER
AND TEST
D
OR
ND
CONDITIONS
PERFORMANCE REQUIREMENTS
Visual examination
Mounting: see Section “Mounting” of this
specification
Procedure B4
Frequency range: 10 to 55 Hz.
Amplitude: 0.75 mm or
Acceleration 98 m/s²
(whichever is less severe)
Total duration 6 hours.
No visible damage
4.7.2 Final inspection
Visual examination
No visible damage
4.9 Shock (see note 3)
Mounting: see Section “Mounting” for
more information
Pulse shape: half sine
Acceleration: 490 m/s²
Duration of pulse: 11 ms.
4.9.2 Final measurements
Visual examination
No visible damage
Capacitance
|ΔC/C| ≤ 5 % of the value measured
initially
Tangent of loss angle
Increase of tan δ:
≤ 0.008
Compared to
initially
4.7 Vibration (see note 3)
Insulation resistance
SUB - GROUP C1 COMBINED
SAMPLE OF SPECIMENS OF SUB GROUPS C1A AND C1B
values
measured
As specified in Section
“Insulation
Resistance” of this specification
D
4.11 Climatic sequence
4.11.1 Initial measurements
Capacitance
Measured in 4.4.2 and 4.9.2
Tangent of loss angle:
Measured initially in C1A and C1B
4.11.2 Dry heat
Temperature: 105 °C
Duration: 16 hours
4.11.3 Damp heat cyclic
Test Db
First cycle
4.11.4 Cold
Temperature: - 55 °C
Duration: 2 hours
4.11.5 Damp heat cyclic
Test Db
remaining cycles
4.11.6 Final measurements
Document Number: 28115
Revision: 12-Jul-07
Visual examination
No visible damage
Legible marking
Capacitance
|ΔC/C| ≤ 5 % of the value measured in
4.11.1.
Tangent of loss angle
Increase of tan δ:
≤ 0.008
Compared to values measured in
4.11.1.
Voltage proof
2250 V (DC); 1 min between term.
No permanent breakdown or flash-over
Insulation resistance
≥ 50 % of values specified in Section
“Insulation
resistance”
of
this
specification
For technical questions, contact: [email protected]
www.vishay.com
179
MKP 336 6 Y2
Vishay BCcomponents Interference Suppression Film Capacitors
MKP Radial Potted Type
SUB - CLAUSE NUMBER
AND TEST
SUB - GROUP C2
D
OR
ND
CONDITIONS
PERFORMANCE REQUIREMENTS
D
4.12 Damp heat steady state
56 days, 40 °C, 90 to 95 % RH no load
capacitance
4.12.1 Initial measurements
Capacitance
Tangent of loss angle at 10 kHz
4.12.3 Final measurements
Visual examination
No visible damage
Legible marking
Capacitance
|ΔC/C| ≤ 5 % of the value measured in
4.12.1.
Tangent of loss angle
Increase of tan δ:
≤ 0.007
Compared to values measured in
4.12.1.
Voltage proof
2250 V (DC); 1 min between term.
No permanent breakdown or flash-over
Insulation resistance
≥ 50 % of values specified in Section
“Insulation
resistance”
of
this
specification
SUB- GROUP C3
D
4.13.1 Initial measurements
Capacitance
Tangent of loss angle at 10 kHz
4.13 Impulse voltage
3 successive impulses, full wave, peak
voltage:
5 kV
Max. 24 pulses
4.14 Endurance
Duration: 1000 hours
1.7 URac at 105 °C
Once in every hour the voltage is
increased to 1000 V (RMS) for 0.1 s via
resistor of 47 Ω ± 5 %
4.14.7 Final measurements
Visual examination
No visible damage
Legible marking
Capacitance
|ΔC/C| ≤ 10 % compared to values
measured in 4.13.1.
Tangent of loss angle
Increase of tan δ:
≤ 0.007
Compared to values measured in
Voltage proof
2250 V (DC);
terminations.
No permanent breakdown or flash-over
1
min
between
Insulation resistance
www.vishay.com
180
No selfhealing breakdowns or flashover
For technical questions, contact: [email protected]
≥ 50 % of values specified in Section
“Insulation
resistance”
of
this
specification
Document Number: 28115
Revision: 12-Jul-07
MKP 336 6
Interference Suppression Film Capacitors
MKP Radial Potted Type
SUB - CLAUSE NUMBER
AND TEST
SUB - GROUP C 4
D
OR
ND
CONDITIONS
Vishay
BCcomponents
PERFORMANCE REQUIREMENTS
D
4.15 Charge and discharge
10 000 cycles
(50 c/s) charge to UR half sinewave
Duration: 5 ms
Discharge resistance:
420 Vdc
R = --------------------------------------------------1.5 × C ( ( dU ) ⁄ ( dt ) )
Rmin = 2.2 Ω
4.15.1 Initial measurements
Capacitance
Tangent of loss angle at 10 kHz
4.15.3 Final measurements
Capacitance
|ΔC/C| ≤ 10 % compared to values
measured in 4.15.1.
Tangent of loss angle
Increase of tan δ:
≤ 0.008
Compared to values measured in
4.15.1.
Insulation resistance
≥ 50 % of values specified in Section
“Insulation
resistance”
of
this
specification
Resonance frequency
As specified in Section “Resonant
frequency” of this specification. ± 10 %
Bore of gas jet: Ø 0.5 mm
Fuel: butane
Test duration for actual volume V in mm³:
V ≤ 250: 10 s
250 < V ≤ 500: 20 s
500 < V ≤ 1750: 30 s
V > 1750: 60 s
One flame application
After removing test flame from capacitor,
the capacitor must not continue to burn
for more than 10 s. No burning particle
must drop from the sample.
SUB - GROUP C5
D
4.16 Radio frequency characteristic
SUB - GROUP C6
D
4.17 Passive flammability
Class B
12 mm
~ 8 mm
45.0 °
SUB - GROUP C7
4.18 Active flammability
Document Number: 28115
Revision: 12-Jul-07
D
20 x 5 kV discharges on the test
capacitor connected to UR
For technical questions, contact: [email protected]
The cheese cloth around the capacitors
shall not burn with a flame.
No
electrical
measurements
are
required.
www.vishay.com
181
Legal Disclaimer Notice
Vishay
Disclaimer
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein
or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any
information provided herein to the maximum extent permitted by law. The product specifications do not expand or
otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed
therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such
applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting
from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding
products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 18-Jul-08
www.vishay.com
1