TI TRS3238ECRHBR

www.ti.com
TRS3238E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
SLLS797 – JUNE 2007
FEATURES
•
•
•
•
•
•
•
•
•
•
•
RS-232 Bus-Pin ESD Protection Exceeds
±15 kV Using Human-Body Model (HBM)
Meets or Exceeds the Requirements of
TIA/EIA-232-F and ITU v.28 Standards
Operates With 3-V to 5.5-V VCC Supply
Operates up to 400 kbit/s
Five Drivers and Three Receivers
Auto-Powerdown Plus Feature Enables
Flexible Power-Down Mode
Low Standby Current . . . 1 μA Typical
External Capacitors . . . 4 × 0.1 μF
Accepts 5-V Logic Input With 3.3-V Supply
Always-Active Noninverting Receiver Output
(ROUT1B)
Alternative High-Speed Pin-Compatible Device
(1 Mbit/s) for TRSF3238
ESD Protection for RS-232 Interface Pins
– ±15 kV – Human-Body Model (HBM)
– ±8 kV – IEC61000-4-2, Contact Discharge
– ±15 kV – IEC61000-4-2, Air-Gap Discharge
DB, DW, OR PW PACKAGE
(TOP VIEW)
C2 +
GND
C2VDOUT1
DOUT2
DOUT3
RIN1
RIN2
DOUT4
RIN3
DOUT5
FORCEON
FORCEOFF
27
3
26
4
25
5
24
6
23
7
22
8
21
9
20
10
19
11
18
12
17
13
16
14
15
C1+
V+
VCC
C1DIN1
DIN2
DIN3
ROUT1
ROUT2
DIN4
ROUT3
DIN5
ROUT1B
INVALID
32 31 30 29 28 27 26 25
DOUT1
DOUT2
DOUT3
RIN1
RIN2
DOUT4
RIN3
N.C.
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
C1–
DIN1
DIN2
DIN3
ROUT1
ROUT2
DIN4
ROUT3
9 10 11 12 13 14 15 16
DOUT5
FORCEON
FORCEOFF
INVALID
N.C.
ROUT1B
DIN5
N.C.
Battery-Powered Systems
PDAs
Notebooks
Subnotebooks
Laptops
Palmtop PCs
Hand-Held Equipment
Modems
Printers
28
2
RHB PACKAGE
(TOP VIEW)
APPLICATIONS
•
•
•
•
•
•
•
•
•
1
VC2–
GND
C2+
C1+
V+
VCC
N.C.
•
N.C. - Not inter nally connected
DESCRIPTION/ORDERING INFORMATION
The TRS3238E consists of five line drivers, three line receivers, and a dual charge-pump circuit with ±15-kV
ESD (HBM) protection on the driver output (DOUT) and receiver input (RIN) terminals. The device meets the
requirements of TIA/EIA-232-F and provides the electrical interface between notebook and subnotebook
computer applications. The charge pump and four small external capacitors allow operation from a single 3-V to
5.5-V supply. In addition, the device includes an always-active noninverting output (ROUT1B), which allows
applications using the ring indicator to transmit data while the device is powered down. This device operates at
data signaling rates up to 250 kbit/s and a maximum of 30-V/μs driver output slew rate.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
UNLESS OTHERWISE NOTED this document contains
PRODUCTION DATA information current as of publication date.
Products conform to specifications per the terms of Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007, Texas Instruments Incorporated
TRS3238E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS797 – JUNE 2007
DESCRIPTION/ORDERING INFORMATION (CONTINUED)
Flexible control options for power management are featured when the serial port and driver inputs are inactive.
The auto-powerdown plus feature functions when FORCEON is low and FORCEOFF is high. During this mode
of operation, if the device does not sense valid signal transitions on all receiver and driver inputs for
approximately 30 s, the built-in charge pump and drivers are powered down, reducing the supply current to
1 μA. By disconnecting the serial port or placing the peripheral drivers off, auto-powerdown plus occurs if there
is no activity in the logic levels for the driver inputs. Auto-powerdown plus can be disabled when FORCEON and
FORCEOFF are high. With auto-powerdown plus enabled, the device activates automatically when a valid signal
is applied to any receiver or driver input. INVALID is high (valid data) if any receiver input voltage is greater than
2.7 V or less than –2.7 V, or has been between –0.3 V and 0.3 V for less than 30 μs. INVALID is low (invalid
data) if all receiver input voltages are between –0.3 V and 0.3 V for more than 30 μs. Refer to Figure 5 for
receiver input levels.
ORDERING INFORMATION
TA
PACKAGE
(1)
(2)
2
TOP-SIDE MARKING
TRS3238ECDB
Reel of 2000
TRS3238ECDBR
Tube of 50
TRS3238ECPW
Reel of 2000
TRS3238ECPWR
SOIC – DW
Reel of 2000
TRS3238ECDWR
TRS3238EC
QFN – RHB
Reel of 2000
TRS3238ECRHBR
PREVIEW
Tube of 50
TRS3238EIDB
Reel of 2000
TRS3238EIDBR
Tube of 50
TRS3238EIPW
Reel of 2000
TRS3238EIPWR
SOIC – DW
Reel of 2000
TRS3238ICDWR
TRS3238EI
QFN – RHB
Reel of 2000
TRS3238EIRHBR
PREVIEW
TSSOP – PW
SSOP – DB
–40°C to 85°C
ORDERABLE PART NUMBER
Tube of 50
SSOP – DB
0°C to 70°C
(1) (2)
TSSOP – PW
TRS3238EC
RS38EC
TRS3238EI
RS38EI
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
Submit Documentation Feedback
TRS3238E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS797 – JUNE 2007
FUNCTION TABLES
abc
Each Driver (1)
INPUTS
DIN
(1)
FORCEON
FORCEOFF
TIME ELAPSED SINCE LAST
RIN OR DIN TRANSITION
OUTPUT
DOUT
DRIVER STATUS
X
X
L
X
Z
Powered off
L
H
H
X
H
H
H
H
X
L
Normal operation with
auto-powerdown plus disabled
L
L
H
<30 s
H
H
L
H
<30 s
L
L
L
H
>30 s
Z
H
L
H
>30 s
Z
Normal operation with
auto-powerdown plus enabled
Powered off by
auto-powerdown plus feature
H = high level, L = low level, X = irrelevant, Z = high impedance
Each Receiver (1)
INPUTS
OUTPUTS
RIN1
RIN2–RIN3
FORCEOFF
TIME ELAPSED SINCE LAST
RIN OR DIN TRANSITION
ROUT1B
ROUT2 AND
ROUT3
RECEIVER STATUS
Powered off while
ROUT1B is active
L
X
L
X
L
Z
H
X
L
X
H
Z
L
L
H
<30 s
L
H
L
H
H
<30 s
L
L
H
L
H
<30 s
H
H
H
H
H
<30 s
H
L
Open
Open
H
<30 s
L
H
(1)
Normal operation with
auto-powerdown plus
disabled/enabled
H = high level, L = low level, X = irrelevant, Z = high impedance (off), Open = input disconnected or connected driver off
Submit Documentation Feedback
3
TRS3238E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS797 – JUNE 2007
LOGIC DIAGRAM (POSITIVE LOGIC)
DIN1
DIN2
DIN3
DIN4
DIN5
FORCEOFF
FORCEON
ROUT1B
ROUT1
ROUT2
ROUT3
4
24
5
23
6
22
7
19
10
17
12
DOUT1
DOUT2
DOUT3
DOUT4
DOUT5
14
13
Auto-powerdown Plus
15
INVALID
16
21
8
20
9
18
11
RIN1
RIN2
RIN3
Submit Documentation Feedback
TRS3238E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS797 – JUNE 2007
Absolute Maximum Ratings
(1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
VCC
Supply voltage range (2)
–0.3
6
V
V+
Positive-output supply voltage range (2)
–0.3
7
V
0.3
–7
V
13
V
V–
Negative-output supply voltage range
V+ – V–
Supply voltage difference (2)
VI
Input voltage range
VO
Output voltage range
θJA
(2)
Driver (FORCEOFF, FORCEON)
–0.3
6
Receiver
–25
25
Driver
Receiver (INVALID)
Package thermal impedance (3) (4)
–13.2
13.2
–0.3
VCC + 0.3
DB package
62
DW package
46
PW package
62
RHB package
TJ
Operating virtual junction temperature
Tstg
Storage temperature range
(1)
(2)
(3)
(4)
UNIT
V
V
°C/W
PREVIEW
–65
150
°C
150
°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are with respect to network GND.
Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
The package thermal impedance is calculated in accordance with JESD 51-7.
Recommended Operating Conditions (1)
See Figure 6
MIN NOM
VCC = 3.3 V
Supply voltage
VCC = 5 V
VIH
Driver and control high-level input voltage
DIN, FORCEOFF,
FORCEON
VIL
Driver and control low-level input voltage
DIN, FORCEOFF, FORCEON
VI
Receiver input voltage
TA
Operating free-air temperature
(1)
3.3
3.6
4.5
5
5.5
VCC = 3.3 V
VCC = 5 V
2
5.5
2.4
5.5
UNIT
V
V
0
0.8
V
–25
25
V
0
70
–40
85
TRS3238EC
TRS3238EI
MAX
3
°C
Testing supply conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.15 V; C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; and C1 = 0.047 μF
and C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
Electrical Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6)
PARAMETER
II
ICC
(1)
(2)
Input leakage current
Supply current
(TA = 25°C)
TEST CONDITIONS
FORCEOFF, FORCEON
MIN
TYP (2)
MAX
±0.01
±1
μA
0.5
2
mA
Auto-powerdown plus
disabled
No load,
FORCEOFF and FORCEON at VCC
Powered off
No load, FORCEOFF at GND
1
10
Auto-powerdown plus
enabled
No load, FORCEOFF at VCC,
FORCEON at GND,
All RIN are open or grounded
1
10
UNIT
μA
Testing supply conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.15 V; C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; and C1 = 0.047 μF
and C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
Submit Documentation Feedback
5
TRS3238E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS797 – JUNE 2007
DRIVER SECTION
xxx
Electrical Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6)
PARAMETER
MIN TYP (2) MAX
TEST CONDITIONS
VOH
High-level output voltage
All DOUT at RL = 3 kΩ to GND
5
5.4
VOL
Low-level output voltage
All DOUT at RL = 3 kΩ to GND
–5
–5.4
IIH
High-level input current
VI = VCC
IIL
Low-level input current
VI at GND
±0.01
μA
μA
±0.01
±1
±35
±60
VCC = 5.5 V,
VO = 0 V
±40 ±100
VO = ±2 V
ro
Output resistance
VCC, V+, and V– = 0 V,
IOZ
Output leakage current
FORCEOFF = GND
(2)
(3)
V
±1
VO = 0 V
Short-circuit output current (3)
(1)
V
VCC = 3.6 V,
IOS
300
UNIT
mA
Ω
10M
VO = ±12 V,
VCC = 3 V to 3.6 V
±25
VO = ±10 V,
VCC = 4.5 V to 5.5 V
±25
μA
Testing supply conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.15 V; C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; and C1 = 0.047 μF
and C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
Short-circuit durations should be controlled to prevent exceeding the device absolute power dissipation ratings, and not more than one
output should be shorted at a time.
Switching Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6)
PARAMETER
TEST CONDITIONS
MIN
TYP (2) MAX
Maximum data rate
CL = 1000 pF,
One DOUT switching,
RL = 3 kΩ,
See Figure 1
tsk(p)
Pulse skew (3)
CL = 150 pF to 2500 pF,
See Figure 2
RL = 3 kΩ to 7 kΩ,
SR(tr)
Slew rate, transition region
(see Figure 1)
VCC = 3.3 V,
RL = 3 kΩ to 7 kΩ
CL = 150 pF to 1000 pF
6
30
CL = 150 pF to 2500 pF
4
30
(1)
(2)
(3)
250
UNIT
400
kbit/s
100
ns
V/μs
Testing supply conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.15 V; C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; and C1 = 0.047 μF
and C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
Pulse skew is defined as |tPLH – tPHL| of each channel of the same device.
ESD Protection
PARAMETER
DOUT
6
TEST CONDITIONS
TYP
HBM
±15
IEC 61000-4-2, Air-Gap Discharge
±15
IEC 61000-4-2, Contact Discharge
±8
Submit Documentation Feedback
UNIT
kV
TRS3238E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS797 – JUNE 2007
RECEIVER SECTION
xxx
Electrical Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6)
PARAMETER
MIN
TYP (2)
VCC – 0.6
VCC – 0.1
TEST CONDITIONS
VOH
High-level output voltage
IOH = –1 mA
VOL
Low-level output voltage
IOL = 1.6 mA
MAX
UNIT
V
0.4
VCC = 3.3 V
1.5
2.4
VCC = 5 V
1.8
2.4
VIT+
Positive-going input threshold voltage
VIT–
Negative-going input threshold voltage
Vhys
Input hysteresis (VIT+ – VIT–)
IOZ
Output leakage current (except ROUT1B)
FORCEOFF = 0 V
ri
Input resistance
VI = ±3 V to ±25 V
VCC = 3.3 V
0.6
1.2
VCC = 5 V
0.8
1.5
V
V
V
0.3
V
±0.05
±10
μA
5
7
kΩ
3
Testing supply conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.15 V; C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; and C1 = 0.047 μF
and C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
(1)
(2)
Switching Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TYP (2)
UNIT
tPLH
Propagation delay time, low- to high-level output
CL = 150 pF, See Figure 3
150
ns
tPHL
Propagation delay time, high- to low-level output
CL = 150 pF, See Figure 3
150
ns
ten
Output enable time
CL = 150 pF, RL = 3 kΩ, See Figure 4
200
ns
tdis
Output disable time
CL = 150 pF, RL = 3 kΩ, See Figure 4
200
ns
tsk(p)
Pulse skew (3)
See Figure 3
50
ns
(1)
(2)
(3)
Testing supply conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.15 V; C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; and C1 = 0.047 μF
and C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
Pulse skew is defined as |tPLH – tPHL| of each channel of the same device.
ESD Protection
PARAMETER
RIN
TEST CONDITIONS
TYP
HBM
±15
IEC 61000-4-2, Air-Gap Discharge
±15
IEC 61000-4-2, Contact Discharge
±8
Submit Documentation Feedback
UNIT
kV
7
TRS3238E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS797 – JUNE 2007
AUTO-POWERDOWN PLUS SECTION
xxx
Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5)
PARAMETER
TEST CONDITIONS
MIN
VT+(valid)
Receiver input threshold
for INVALID high-level output voltage
FORCEON = GND, FORCEOFF = VCC
VT–(valid)
Receiver input threshold
for INVALID high-level output voltage
FORCEON = GND, FORCEOFF = VCC
–2.7
VT(invalid)
Receiver input threshold
for INVALID low-level output voltage
FORCEON = GND, FORCEOFF = VCC
–0.3
VOH
INVALID high-level output voltage
IOH = –1 mA, FORCEON = GND,
FORCEOFF = VCC
VOL
INVALID low-level output voltage
IOL = 1.6 mA, FORCEON = GND,
FORCEOFF = VCC
MAX
2.7
UNIT
V
V
0.3
VCC – 0.6
V
V
0.4
V
Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5)
PARAMETER
TYP (1)
MAX
UNIT
tvalid
Propagation delay time, low- to high-level output
0.1
μs
tinvalid
Propagation delay time, high- to low-level output
50
μs
ten
Supply enable time
25
tdis
Receiver or driver edge to auto-powerdown plus
(1)
8
MIN
All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
Submit Documentation Feedback
15
30
μs
60
s
TRS3238E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS797 – JUNE 2007
PARAMETER MEASUREMENT INFORMATION
3V
Generator
(see Note B)
Input
RS-232
Output
50 Ω
RL
tTHL
CL
(see Note A)
3V
FORCEOFF
TEST CIRCUIT
0V
3V
3V
Output
SR(tr) +
tTLH
−3 V
−3 V
6V
t THL or tTLH
VOH
VOL
VOLTAGE WAVEFORMS
A.
CL includes probe and jig capacitance.
B.
The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns,
tf ≤ 10 ns.
Figure 1. Driver Slew Rate
3V
Generator
(see Note B)
RS-232
Output
50 Ω
RL
Input
1.5 V
1.5 V
0V
CL
(see Note A)
tPHL
tPLH
VOH
3V
FORCEOFF
50%
50%
Output
VOL
TEST CIRCUIT
VOLTAGE WAVEFORMS
A.
CL includes probe and jig capacitance.
B.
The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns,
tf ≤ 10 ns.
Figure 2. Driver Pulse Skew
3 V or 0 V
FORCEON
3V
Input
1.5 V
1.5 V
−3 V
Output
Generator
(see Note B)
tPHL
50 Ω
3V
FORCEOFF
tPLH
CL
(see Note A)
VOH
50%
Output
50%
VOL
TEST CIRCUIT
VOLTAGE WAVEFORMS
A.
CL includes probe and jig capacitance.
B.
The pulse generator has the following characteristics: ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns.
Figure 3. Receiver Propagation Delay Times
Submit Documentation Feedback
9
TRS3238E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS797 – JUNE 2007
PARAMETER MEASUREMENT INFORMATION (continued)
3V
Input
VCC
3 V or 0 V
FORCEON
1.5 V
0V
tPHZ
(S1 at GND)
RL
3 V or 0 V
1.5 V
GND
S1
VOH
Output
50%
Output
CL
(see Note A)
FORCEOFF
Generator
(see Note B)
0.3 V
tPLZ
(S1 at VCC)
50 Ω
tPZL
(S1 at VCC)
0.3 V
Output
50%
VOL
TEST CIRCUIT
VOLTAGE WAVEFORMS
A.
CL includes probe and jig capacitance.
B.
The pulse generator has the following characteristics: ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns.
C.
tPLZ and tPHZ are the same as tdis.
D.
tPZL and tPZH are the same as ten.
Figure 4. Receiver Enable and Disable Times
10
Submit Documentation Feedback
TRS3238E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS797 – JUNE 2007
PARAMETER MEASUREMENT INFORMATION (continued)
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
Valid RS-232 Level, INVALID High
ROUT
Generator
(see Note B)
2.7 V
50 Ω
Indeterminate
0.3 V
0V
−0.3 V
Indeterminate
Autopowerdown
Plus
INVALID
−2.7 V
CL = 30 pF
(see Note A)
Valid RS-232 Level, INVALID High
†
FORCEOFF
FORCEON
If Signal Remains Within This Region
For More Than 30 µs, INVALID Is Low†
DIN
DOUT
Auto-powerdown plus disables drivers and reduces
supply current to 1 µA.
TEST CIRCUIT
NOTES: A. CL includes probe and jig capacitance.
B. The pulse generator has the following
characteristics: PRR = 5 kbit/s, ZO = 50 Ω, 50%
duty cycle, tr ≤ 10 ns, tf ≤ 10 ns.
Receiver
Input
3V
2.7 V
0V
0V
−2.7 V
−3 V
tinvalid
tvalid
INVALID
Output
Driver
Input
50%
VCC
50%
0V
3 V to 5 V
50%
50%
0V
≈5.5 V
Driver
Output
≈ −5.5 V
tdis
ten
tdis
ten
V+
Supply
Voltages
V+
V+ −0.3 V
V− +0.3 V
V−
V−
Voltage Waveforms and Timing Diagrams
Figure 5. INVALID Propagation-Delay Times and Supply-Enabling Time
Submit Documentation Feedback
11
TRS3238E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS797 – JUNE 2007
APPLICATION INFORMATION
CBYPASS = 0.1 µF
+
−
1
2
+
C2
27
+
GND
−
4
+
V+
28
−
3
−
C1+
C2+
C2−
VCC
V−
C1−
C4
DOUT1
DOUT2
DOUT3
RIN1
C3†
+
−
26
C1
25
5
24
6
23
7
22
8
21
9
20
DIN1
DIN2
DIN3
ROUT1
RS-232 Port
RIN2
ROUT2
Logic I/Os
5 kΩ
DOUT4
RIN3
10
19
11
18
DIN4
ROUT3
5 kΩ
DOUT5
12
17
16
DIN5
ROUT1B
5 kΩ
FORCEON
FORCEOFF
13
14
Autopowerdown
Plus
15
INVALID
VCC vs CAPACITOR VALUES
VCC
†
C3 can be connected to VCC or GND.
NOTES: A. Resistor values shown are nominal.
B. Nonpolarized ceramic capacitors are acceptable. If polarized tantalum
or electrolytic capacitors are used, they should be connected as
shown.
3.3 V ± 0.15 V
3.3 V ± 0.3 V
5 V ± 0.5 V
3 V to 5.5 V
Figure 6. Typical Operating Circuit and Capacitor Values
12
Submit Documentation Feedback
C1
0.1 µF
0.22 µF
0.047 µF
0.22 µF
C2, C3, and C4
0.1 µF
0.22 µF
0.33 µF
1 µF
PACKAGE OPTION ADDENDUM
www.ti.com
26-Sep-2007
PACKAGING INFORMATION
(1)
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TRS3238ECDB
ACTIVE
SSOP
DB
28
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238ECDBG4
ACTIVE
SSOP
DB
28
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238ECDBR
ACTIVE
SSOP
DB
28
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238ECDBRG4
ACTIVE
SSOP
DB
28
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238ECDW
ACTIVE
SOIC
DW
28
20
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238ECDWG4
ACTIVE
SOIC
DW
28
20
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238ECDWR
ACTIVE
SOIC
DW
28
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238ECDWRG4
ACTIVE
SOIC
DW
28
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238ECPW
ACTIVE
TSSOP
PW
28
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238ECPWG4
ACTIVE
TSSOP
PW
28
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238ECPWR
ACTIVE
TSSOP
PW
28
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238ECPWRG4
ACTIVE
TSSOP
PW
28
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238EIDB
ACTIVE
SSOP
DB
28
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238EIDBG4
ACTIVE
SSOP
DB
28
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238EIDBR
ACTIVE
SSOP
DB
28
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238EIDBRG4
ACTIVE
SSOP
DB
28
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238EIDW
ACTIVE
SOIC
DW
28
20
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238EIDWG4
ACTIVE
SOIC
DW
28
20
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238EIDWR
ACTIVE
SOIC
DW
28
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238EIDWRG4
ACTIVE
SOIC
DW
28
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238EIPW
ACTIVE
TSSOP
PW
28
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238EIPWG4
ACTIVE
TSSOP
PW
28
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238EIPWR
ACTIVE
TSSOP
PW
28
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3238EIPWRG4
ACTIVE
TSSOP
PW
28
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
The marketing status values are defined as follows:
Addendum-Page 1
Lead/Ball Finish
MSL Peak Temp (3)
PACKAGE OPTION ADDENDUM
www.ti.com
26-Sep-2007
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
TRS3238ECDBR
Package Package Pins
Type Drawing
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
SSOP
DB
28
2000
330.0
16.4
8.2
10.5
2.5
12.0
16.0
Q1
TRS3238ECDWR
SOIC
DW
28
1000
330.0
32.4
11.35
18.67
3.1
16.0
32.0
Q1
TRS3238ECPWR
TSSOP
PW
28
2000
330.0
16.4
7.1
10.4
1.6
12.0
16.0
Q1
TRS3238EIDBR
SSOP
DB
28
2000
330.0
16.4
8.2
10.5
2.5
12.0
16.0
Q1
TRS3238EIDWR
SOIC
DW
28
1000
330.0
32.4
11.35
18.67
3.1
16.0
32.0
Q1
TRS3238EIPWR
TSSOP
PW
28
2000
330.0
16.4
7.1
10.4
1.6
12.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TRS3238ECDBR
SSOP
DB
28
2000
346.0
346.0
33.0
TRS3238ECDWR
SOIC
DW
28
1000
346.0
346.0
49.0
TRS3238ECPWR
TSSOP
PW
28
2000
346.0
346.0
33.0
TRS3238EIDBR
SSOP
DB
28
2000
346.0
346.0
33.0
TRS3238EIDWR
SOIC
DW
28
1000
346.0
346.0
49.0
TRS3238EIPWR
TSSOP
PW
28
2000
346.0
346.0
33.0
Pack Materials-Page 2
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
DB (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
28 PINS SHOWN
0,38
0,22
0,65
28
0,15 M
15
0,25
0,09
8,20
7,40
5,60
5,00
Gage Plane
1
14
0,25
A
0°–ā8°
0,95
0,55
Seating Plane
2,00 MAX
0,10
0,05 MIN
PINS **
14
16
20
24
28
30
38
A MAX
6,50
6,50
7,50
8,50
10,50
10,50
12,90
A MIN
5,90
5,90
6,90
7,90
9,90
9,90
12,30
DIM
4040065 /E 12/01
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-150
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DLP® Products
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated