RECORDS OF REVISION LQ150X1LGN2A SPEC No. DATE No. LD-16Z09 Jan.25.2005 SUMMARY REVISED NOTE PAGE 1st Issue LD-16Z09-1 1. Application This specification applies to the color 15.0 XGA TFT-LCD module LQ150X1LGN2A. ◎This specification are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. ◎The device listed in this technical literature was designed and manufactured for use in OA equipment. ◎In case of using the device for applications such as control and safety equipment for transportation(aircraft, trains, automobiles, etc. ), rescue and security equipment and various safety related equipment which require higher reliability and safety, take into consideration that appropriate measures such as fail-safe functions and redundant system design should be taken. ◎Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications, telecommunication equipment(trunk lines), nuclear power control equipment and medical or other equipment for life support. ◎SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in these specification sheets. ◎Contact and consult with a SHARP sales representative for any questions about this device. 2. Overview This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit and a back light unit. Graphics and texts can be displayed on a 1024×RGB×768 dots panel with about 16 million colors by using LVDS (Low Voltage Differential Signaling) and supplying +3.3V DC supply voltages for TFT-LCD panel driving and supply voltage for backlight. LD-16Z09-2 3. Mechanical Specifications Parameter Display size Specifications Unit 38 (Diagonal) cm 15.0 (Diagonal) Inch Active area 304.1 (H)×228.1 (V) mm Pixel format 1024 (H)×768 (V) Pixel (1 pixel＝R+G+B dots) Pixel pitch 0.297 (H)×0.297 (V) Pixel configuration R, G, B vertical stripe Display mode Normally white Unit outline dimensions *1 326.0(W)×252.0(H)×11.5(D) Mass 1100 Surface treatment Anti-glare and hard-coating 2H (MAX) (Haze value = 28) *1.Note: excluding back light cables, cover and pet sheet. The thickness of module (D) doesn’t contain the projection. Outline dimensions are shown in Fig.1. mm mm g LD-16Z09-3 4. Input Terminals 4-1. TFT-LCD panel driving CN1 (Interface signals and +3.3V DC power supply) Using connectors ：DF14H-20P-1.25H (Hirose Electric Co., Ltd.) Corresponding connectors ：DF14-20S-1.25C(Connector) DF14-2628SCFA(Terminal) Corresponding LVDS Transmitter ：THC63LVDM83R(Thine) or compatible Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Symbol Vcc Vcc GND GND RXIN0RXIN0+ GND RXIN1RXIN1+ GND RXIN2RXIN2+ GND RXCKINRXCKIN+ GND RXIN3RXIN3+ GND LVDS_SET Function Remark +3.3V Power supply +3.3V Power supply Receiver signal (-) Receiver signal (+) LVDS LVDS Receiver signal (-) Receiver signal (+) LVDS LVDS Receiver signal (-) Receiver signal (+) LVDS LVDS Clock signal (-) Clock signal (+) LVDS LVDS Receiver signal (-) Receiver signal (+) LVDS LVDS LVDS_SET 【note1】 LD-16Z09-4 4-2 Data Mapping 1) 8 bit input 【note1】pin assignment with LVDS_SET pin (Thine:THC63LVDM83R) Transmitter 20pin LVDS_SET Pin No Data =L (GND) or Open =H (3.3V) 51 52 54 55 56 3 4 6 7 11 12 14 15 19 20 22 23 24 27 28 30 50 2 8 10 16 18 25 TA0 TA1 TA2 TA3 TA4 TA5 TA6 TB0 TB1 TB2 TB3 TB4 TB5 TB6 TC0 TC1 TC2 TC3 TC4 TC5 TC6 TD0 TD1 TD2 TD3 TD4 TD5 TD6 R2 R3 R4 R5 R6 R7 (MSB) G2 G3 G4 G5 G6 G7 (MSB) B2 B3 B4 B5 B6 B7 (MSB) (NA) (NA) DE R0 (LSB) R1 G0 (LSB) G1 B0 (LSB) B1 (NA) R0 (LSB) R1 R2 R3 R4 R5 G0 (LSB) G1 G2 G3 G4 G5 B0 (LSB) B1 B2 B3 B4 B5 (NA) (NA) DE R6 R7 (MSB) G6 G7 (MSB) B6 B7 (MSB) (NA) LD-16Z09-5 <LVDS_SET=L or Open> 1 cycle RxCKIN+ RxCKIN- RXIN0+ RXIN0- R3 R2 G2 R7 R6 R5 R4 R3 R2 G2 RXIN1+ RXIN1- G4 G3 B3 B2 G7 G6 G5 G4 G3 B3 B5 B4 DE NA NA B7 B6 B5 B4 DE R1 R0 NA B1 B0 G1 G0 R1 R0 NA RXIN2+ RXIN2RXIN3+ RXIN3DE : Display Enable NA : Not Available <LVDS_SET =H> 1 cycle RxCXIN+ RxCXIN- RxIN0+ RxIN0- R1 R0 G0 R5 R4 R3 R2 R1 R0 G0 RxIN1+ RxIN1- G2 G1 B1 B0 G5 G4 G3 G2 G1 B1 B3 B2 DE NA NA B5 B4 B3 B2 DE R7 R6 NA B7 B6 G7 G6 R7 R6 NA RxIN2+ RxIN2RxIN3+ RxIN3DE : Display Enable NA : Not Available LD-16Z09-6 2) 6 bit input 【note1】pin assignment with LVDS_SET pin (Thine:THC63LVDM83R) Transmitter 20pin LVDS_SET Pin No Data =L (GND) or Open =H (3.3V) 51 52 54 55 56 3 4 6 7 11 12 14 15 19 20 22 23 24 27 28 30 50 2 8 10 16 18 25 TA0 TA1 TA2 TA3 TA4 TA5 TA6 TB0 TB1 TB2 TB3 TB4 TB5 TB6 TC0 TC1 TC2 TC3 TC4 TC5 TC6 TD0 TD1 TD2 TD3 TD4 TD5 TD6 R0 (LSB) R1 R2 R3 R4 R5 (MSB) G0 (LSB) G1 G2 G3 G4 G5 (MSB) B0 (LSB) B1 B2 B3 B4 B5 (MSB) (NA) (NA) DE GND GND GND GND GND GND (NA) − − − − − − − − − − − − − − − − − − − − − − − − − − − − 1 cycle RXCKIN+ RXCKIN- RXIN0+ RXIN0- R1 R0 G0 R5 R4 R3 R2 R1 R0 G0 RXIN1+ RXIN1- G2 G1 B1 B0 G5 G4 G3 G2 G1 B1 B3 B2 DE NA NA B5 B4 B3 B2 DE RXIN2+ RXIN2DE : Display Enable NA : Not Available ※In case of supplying 6 bit signal, it is recommended to connect pin No.17(Rx3-) with VCC(3.3V), and No.18(Rx3+) with GND(0V). 4-3 Interface block diagram LD-16Z09-7 (TFT-LCD side) (Computer Side) ①8Bit Mode LVDS_SET=H (20 pin=3.3[V]) G1-G5,B0,B1 B2-B5, NA,NA,DE 7 TC 0 - 6 7 R6,R7,G6,G7, B6,B7,NA TD 0 - 6 RX0+(6) TTL PARALLEL-TO-LVDS R0-R5,G0 RX0-(5) RX1+(9) RX1-(8) RX2+(12) RX2-(11) RX3+(18) RX3-(17) Single LVDS interface contained in a control RA 0 - 6 RB 0 - 6 RC 0 - 6 RD 0 - 6 Internal circuits THC63LVDM83R 7 TA 0 - 6 7 TB 0 - 6 LVDS-TO-PARALLEL TTL Controll CK+(15) CＬK IN CK PLL ＣK-(14) PLL CK OUT ②8Bit Mode LVDS_SET=L (20 pin=GND or OPEN) G3-G7,B2,B3 B4-B7, NA,NA,DE 7 TC 0 - 6 7 R0,R1,G0,G1, B0,B1,NA TD 0 - 6 RX0+(6) TTL PARALLEL-TO-LVDS R2-R7,G2 RX0-(5) RX1+(9) RX1-(8) RX2+(12) RX2-(11) RX3+(18) RX3-(17) Single LVDS interface contained in a control IC RA 0 - 6 RB 0 - 6 RC 0 - 6 RD 0 - 6 Internal circuits THC63LVDM83R 7 TA 0 - 6 7 TB 0 - 6 LVDS-TO-PARALLEL TTL Controll CK+(15) CＬK IN CK PLL ＣK-(14) PLL CK OUT ③6Bit Mode LVDS_SET=L (20 pin=GND or OPEN) G1-G5,B0,B1 B2-B5, NA,NA,DE GND×6,NA 7 TC 0 - 6 7 TD 0 - 6 RX0+(6) TTL PARALLEL-TO-LVDS R0-R5,G0 RX0-(5) RX1+(9) RX1-(8) RX2+(12) RX2-(11) RX3+(18) RX3-(17) Single LVDS interface contained in a control IC RA 0 - 6 RB 0 - 6 RC 0 - 6 RD 0 - 6 CK+(15) CK CＬK IN PLL ＣK-(14) PLL CK OUT Internal circuits THC63LVDM83R 7 TA 0 - 6 7 TB 0 - 6 LVDS-TO-PARALLEL TTL Controll LD-16Z09-8 4-4 Backlight CN 2, 3 ：BHSR-02VS-1 The module-side connector (JST) ：SM02B-BHSS-1-TB The user-side connector (JST) Pin no. symbol I/O Function 1 ＶHIGH I Power supply for lamp (High voltage side) 2 ＶLOW I Power supply for lamp (Low voltage side) TFT LCD back view Red cable is VHIGH 1 Gray cable is VLOW 2 Blue cable is VHIGH 1 CN2 CN3 Gray cable is VLOW 2 5. Absolute Maximum Ratings Parameter Symbol Condition Ratings Vcc Ta=25℃ 0 ∼ + 4.0 Ｖ Lamp Input voltage VHIGH − 0 ∼ + 2700 Ｖrms Storage temperature TSTG − Operating temperature TOPA Panel surface Supply voltage 【Note1】Humidity：95%RH Max. Unit −25 ∼ + 60 ℃ 0 ∼ + 60 ℃ ( Ta≦40℃ ) Maximum wet-bulb temperature at 39℃ or less. No condensation. ( Ta>40℃ ) Remark 【Note1】 LD-16Z09-9 6. Electrical Characteristics 6-1. TFT-LCD panel driving Ta＝25℃ Parameter Vcc Symbol Min. Typ. Max. Unit Remark Supply voltage Vcc +3.0 +3.3 +3.6 V 【Note2】 Current dissipation Icc − 425 700 mA 【Note3】 − − 100 mVp-p Vcc=+3.3V − − +100 mV VCM=+1.2V Permissive input ripple voltage Differential input High VRF VTH threshold voltage Low VTL –100 − − mV Input current (High) IOH − − ±10 μA 【Note1】 VI=2.4V, Vcc=3.6V Input current (Low) IOL − ±10 μA VI=0V, Vcc=3.6V Terminal resistor RT − − 100 − Ω Differential input 【Note1】 VCM : Common mode voltage of LVDS driver. 【Note2】 1）On-off sequences of Vcc and data 0.9Vcc 0.1Vcc 0.1Vcc Vcc 0＜t1≦10ms data 0＜t2≦10ms 0.9Vcc t1 t2 0＜t3≦1s 1s≦t4 Back light t4 t3 t5 0.1Vcc ON OFF OFF 200ms≦t5 Power sequence for Backlight is not especially specified, however it is recommended to consider some timing difference between LVDS input and Backlight input as shown above. If the Backlight lights on before LCD starting, or if the Backlight is kept on after LCD stopping, the screen may look white for a moment or abnormal image may be displayed. This is caused by variation in output signal from timing generator at LVDS input on or off. It does not cause the damage to the LCD module. Vcc 2）Dip conditions for supply voltage 1) 2) V2 ≦Vcc＜ V1 td≦ 10ms V1 : 3.0V Vcc＜V2 Vcc-dip conditions should also V2 V2 : 2.5V V1 follow the on-off conditions. td 【Note3】 Typical current situation : 16-gray-bar pattern RGB GS0 RGB RGB GS4 GS8 .... Vcc=+3.3V, CK=65MHz Horizontal period =20.7 us Gray scale : GS(4n) n=0∼15 The explanation of each gray scale, GS(4n), is described below section 8-2. RGB GS56 RGB GS60 LD-16Z09-10 6-2. Backlight The back light system is an edge-lighting type with 2 CCFTs (Cold Cathode Fluorescent Tube). The characteristics of the lamp are shown in the following table. The value mentioned below is at the case of one CCFT. CCFT Model Name : KTBE24MSTF-530.5KB270-Z-L (STANLEY ELECTRIC CO.,LTD) Parameter Symbol Min. Typ. Max. Unit Remark Lamp current range IL 3.0 4.0 5.0 mArms 【Note1】 1050 1200 Vrms Lamp voltage VL − IL=4.0 mArms Ta=25℃ 60kHz Lamp power consumption PL 4.2 4.8 W − 【Note2】 IL=4.0 mArms Ta=25℃ 60kHz Lamp frequency FL 40 60 70 kHz 【Note3】 Kick-off voltage Vs 2200 Vrms − − Ta=0℃ 60kHz【Note4】 Lamp life time TL 50,000 hour 【Note5】 − − 【Note1】 A lamp can be light in the range of lamp current shown above. Maximum rating for current is measured by high frequency current measurement equipment connected to VLOW at circuit showed below. (Note : To keep enough kick-off voltage and necessary steady voltage for CCFT.) Lamp frequency : 40∼70kHz Ambient temperature : 0∼50℃ 1 Module 2 Inverter Ａ ∼ 【Note2】 Referential data per one CCFT by calculation ( IL × VL ) . The data don’t include loss at inverter. 【Note3】Lamp frequency of inverter may produce interference with horizontal synchronous frequency, and this may cause horizontal beat on the display. Therefore, adjust lamp frequency, and keep inverter as far as from module or use electronic shielding between inverter and module to avoid interference. 【Note4】This is transformer output voltage at 33pF for the ballast capacitor of a DC-AC inverter. The kick-off voltage may rise up in the user set, please decide the open output voltage by checking not to occur lighting failure under operating state. The open output voltage should be applied to the lamp for more than 1 second to startup. Otherwise the lamp may not be turned on. ballast capacitor(33pF) Module 1 Inverter V ∼ 2 ＊ 2pin VLOW LD-16Z09-11 【Note5】 Lamp life time is defined as the time when either ① or ② occurs in the continuous operation under the condition of Ta=25℃ and IL=4.0 mA rms. ① Brightness becomes 50% of the original value under standard condition. ② Kick-off voltage at Ta=0℃ exceeds 2200 Vrms value. 《Note》 The performance of the backlight, for example lifetime or brightness, is much influenced by the characteristics of the DC-AC inverter for the lamp. When you design or order the inverter, please make sure that a poor lighting caused by the mismatch of the backlight and the inverter (miss-lighting, flicker, etc.) never occurs. When you confirm it, the module should be operated in the same condition as it is installed in your instrument. Use the lamp inverter power source incorporating such safeguard as overvoltage / overcurrent protective circuit or lamp voltage waveform detection circuit, which should have individual control of each lamp. In case one circuit without such individual control is connected to more than two lamps, excessive current may flow into one lamp when the other one is not in operation. 7. Timing characteristics of input signals 7-1. Timing characteristics Parameter Symbol Min. Typ. Max. Unit Clock signal Frequency 1/Tc 50.0 65.0 80.0 MHz ENAB signal Horizontal period TH 1056 1344 1720 clock 16.0 20.7 23.4 µs Horizontal period (High) THd 1024 1024 1024 clock Vertical period TV 773 806 990 line Vertical period (High) TVd 768 768 768 line 【Note】 In case of using the long vertical period, the deterioration of display quality, flicker etc. may occur. TH THd DE DATA (R,G,B) 1024 1 1024 2 Tc 1 767 2 DE TVd TV 768 LD-16Z09-12 7-2 Input Data Signals and Display Position on the screen R1 G1 B1 R2 G2 B2 (１､１) (１,２) １・１ １・２ １・３ 1･1024 ２・１ ２・２ ３・１ R G B 768･1024 768･1 Display Position of Data (V,H) LD-16Z09-13 8. Input Signals, Basic Display Colors and Gray Scale of Each Color 8-1 8bit input Data signal Colors & Gray R0 R1 R2 R3 R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 B4 B5 B6 B7 Gray scale Scale Basic Color Gray Scale of Red Gray Scale of Green Gray Scale of Blue Black − 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Blue − 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 X X 1 1 1 1 1 1 Green − 0 0 0 0 0 0 0 0 X X 1 1 1 1 1 1 0 0 0 0 0 0 0 0 Cyan − 0 0 0 0 0 0 0 0 X X 1 1 1 1 1 1 X X 1 1 1 1 1 1 Red − X X 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Magenta − X X 1 1 1 1 1 1 0 0 0 0 0 0 0 0 X X 1 1 1 1 1 1 Yellow − X X 1 1 1 1 1 1 X X 1 1 1 1 1 1 0 0 0 0 0 0 0 0 White − X X 1 1 1 1 1 1 X X 1 1 1 1 1 1 X X 1 1 1 1 1 1 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 × GS1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Darker GS2 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 × È È È È Ø È È È È Brighter GS250 0 1 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Ø GS251 1 1 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Red GS252 X X 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 × GS1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Darker GS2 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 × È È È È Ø È È È È Brighter GS250 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 0 0 0 0 0 0 0 0 Ø GS251 0 0 0 0 0 0 0 0 1 1 0 1 1 1 1 1 0 0 0 0 0 0 0 0 Green GS252 0 0 0 0 0 0 0 0 X X 1 1 1 1 1 1 0 0 0 0 0 0 0 0 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 × GS1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 Darker GS2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 × È È È È Ø È È È È Brighter GS250 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 Ø GS251 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 1 1 1 1 1 Blue GS252 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 X X 1 1 1 1 1 1 0 : Low level voltage, 1 : High level voltage. X :Don’t care. Each basic color can be displayed in 253 gray scales from 8 bit data signals. According to the combination of total 24 bit data signals, the 16-million-color display can be achieved on the screen. LD-16Z09-14 8-2 6bit input Data signal Colors & Gray Gray scale Scale Black Basic Color Gray Scale of Red Gray Scale of Green Gray Scale of Blue R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5 − 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Blue − 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 Green − 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 Cyan − 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 Red − 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Magenta − 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 Yellow − 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 White − 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 × GS1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Darker GS2 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 × È È È È Ø È È È È Brighter GS61 1 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Ø GS62 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Red GS63 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 × GS1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 Darker GS2 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 × È È È È Ø È È È È Brighter GS61 0 0 0 0 0 0 1 0 1 1 1 1 0 0 0 0 0 0 Ø GS62 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 Green GS63 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 × GS1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 Darker GS2 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 × È È È È Ø È È È È Brighter GS61 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 1 1 1 Ø GS62 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 Blue GS63 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 : Low level voltage, 1 : High level voltage. Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of total 18 bit data signals, the 262,144-color display can be achieved on the screen. LD-16Z09-15 9. Optical Characteristics Ta=25℃, Vcc =+3.3V Parameter Viewing Symbol Condition Min. Typ. Max. Unit Remark θ11 CR≧5 40 55 − Deg. 【Note1,4】 θ12 70 80 − Deg. Horizontal θ21,θ22 70 80 − Deg. Vertical θ11 30 45 − Deg. θ12 45 55 − Deg. θ21,θ22 50 60 − Deg. 250 350 − Vertical angle range Horizontal ＣＲ Contrast ratio CR≧10 θ=0° 【Note2,4】 Rise γr − 5 20 ms Fall γd − 20 40 ms Chromaticity of x 0.283 0.313 0.343 White y 0.299 0.329 0.359 Chromaticity of x 0.551 0.581 0.611 Red y 0.292 0.322 0.352 Chromaticity of x 0.277 0.307 0.337 Green y 0.516 0.546 0.576 Chromaticity of x 0.121 0.151 0.181 Blue y 0.097 0.127 0.157 Luminance of white YL 200 260 − Response Time θ=0° 【Note3,4】 【Note4】 cd/m2 IL=4.0mA rms fL=60kHz 【Note4】 δw White Uniformity ※The − − 1.25 − 【Note5】 measurement shall be executed 30 minutes after lighting at rating. The optical characteristics shall be measured in a dark room or equivalent state with the method shown in Fig.2 below. Photodetector(EZ-CONTRAST） ４００mm Photodetector Contrast ratio/Response Time(BM-5A) Luminance(BM-7) Chromaticity(SR-3) Field=2° Center of screen(θ=0°） Center of screen(θ=0°) TFT-LCD-Module TFT-LCD-Module Fig2-1 Viewing angle measurement method Fig2-2 Luminance/Contrast ratio/Response time/Chromaticity measurement method Fig2 Optical characteristics measurement method LD-16Z09-16 【Note1】Definitions of viewing angle range: Normal line θ11 θ22 θ21 θ12 6 o’clock 【Note2】Definition of contrast ratio: The contrast ratio is defined as the following. Luminance (brightness) with all pixels white Contrast Ratio (CR) ＝ Luminance (brightness) with all pixels black 【Note3】Definition of response time: The response time is defined as the following figure and shall be measured by switching the input Photodetector Output (Relative Value) signal for "black" and "white". White black white 100% 90% 10% 0% τr τd time 【Note4】This shall be measured at center of the screen. 【Note5】Definition of white uniformity: White uniformity is defined as the following with five measurements 256 512 A 768 D C B pixel 192 384 E (A∼E). 576 pixel δw＝ Maximum Luminance of five points (brightness) Minimum Luminance of five points (brightness) LD-16Z09-17 10. Handling Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable. b) Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist. c) Since the front polarize is easily damaged, pay attention not to scratch it. d) Since long contact with water may cause discoloration or spots, wipe off water drop immediately. e) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Handle with care. g) Since CMOS LSI is used in this module, take care of static electricity and take the human earth into consideration when handling. h) Make sure the four mounting holes of the module are grounded sufficiently. Take electro-magnetic interference (EMI) into consideration. i) The module has some printed circuit boards (PCBs) on the back side. Take care to keep them form any stress or pressure when handling or installing the module; otherwise some of electronic parts on the PCBs may be damaged. j) Observe all other precautionary requirements in handling components. k) When some pressure is added onto the module from rear side constantly, it causes display non-uniformity issue, functional defect, etc. So, please avoid such design. l) When handling LCD modules and assembling them into cabinets, please be noted that long-term storage in the environment of oxidization or deoxidization gas and the use of such materials as reagent, solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and discoloration of the LCD modules. 11. Packing form a) Production country : JAPAN , TAIWAN, CHINA b) Piling number of cartons : maximum 6 cartons c) Packing quantity in one carton : d) Carton size : 10 modules 408mm(W)×340mm(H)×398mm(D) e) total mass of one carton filled with full modules : f) Packing form is shown in Fig.3 12.0kg(typ.) LD-16Z09-18 12．Reliability test items No 1 Test item High temperature storage test Conditions Ta = 60℃ 240h 240h 2 Low temperature storage test Ta = -25℃ 3 High temperature Ta = 40℃ ; 95%RH & high humidity operation test (No condensation) High temperature operation test Ta = 60℃ 4 240h 240h (The temperature of panel surface) 5 Low temperature operation test Ta = 0℃ 240H 6 Vibration test Waveform : Sine wave (non- operating) Frequency : 10∼57Hz/Vibration width (one side) : 0.075mm : 58∼500Hz/Gravity : 9.8m/s2 Sweep time : 11minutes Test period : 3 hours (1 hour for each direction of X,Y,Z) 7 Shock test Max. gravity : 490m/s2 (non- operating) Pulse width : 11ms, sine wave Direction : ±X, ±Y, ±Z, once for each direction. 8 9 Thermal shock test Ta=-25℃∼60℃ ; 5 cycles (Storage) Test period : 10 hours (1 hour for each temperature) Altitude Ta=50℃,70kPa,3,048m(10,000ft), t=24h (Operating) Ta=70℃,12kPa,15,240m(50,000ft), t=24h (Storage) 【Result Evaluation Criteria】 Under the display quality test conditions with normal operation state, these shall be no change which may affect practical display function. LD-16Z09-19 13．Others 1) Lot No. and indication Bar Code Label: P R A H S Production country Model No. LQ150X1LGN2A XX XXXXXXX MADE IN JAPAN Bar Code( Lot No. ) Lot No. Production Country Japan MADE IN JAPAN Taiwan MADE IN TAIWAN China MADE IN CHINA How to express Lot No. Serial No. A production year (the last figures of the Christian Era) A production month (1∼9,X,Y,Z) 2) Packing Label （４Ｓ）LQ150X1LGN2A 社内品番： TYPE ＬＱ１５０Ｘ１ＬＧＮ２Ａ QUANTITY １０ ① Bar code（①） ＬｏｔＮＯ． （１Ｔ）２００４．Ｘ．ＸＸ ： Bar code（②） LOT(DATA) （Ｑ） Ｑｕａｎｔｉｔｙ： １０ ｐｃｓ ： ② Made in TAIWAN Bar code（③） ユーザ品番 ０４．０９．２４ ③ ① Model No. (LQ150X1LGN2A) ② Lot No. (Date) シャープ物流用ラベルです。 Made in JAPAN / CHINA ③ Quantity 3) Adjusting volume have been set optimally before shipment, so do not change any adjusted value. If adjusted value is changed, the specification may not be satisfied. 4) Disassembling the module can cause permanent damage and should be strictly avoided. 5) Please be careful since image retention may occur when a fixed pattern is displayed for a long time. 6) The chemical compound which causes the destruction of ozone layer is not being used. 7) Warning of mercury and material information of LPG (Light Pipe Guide) are printed on the back of the module. MATERIAL INFORMATION >PLASTIC LIGHT GUIDE:PMMA< 8)Cold cathode fluorescent lamp in LCD PANEL contains a small amount of mercury, Please follow local ordinances or regulations for disposal. COLD CATHODE FLUORESCENT LAMP IN LCD PANEL CONTAINS A SMALL AMOUNT OF MERCURY, PLEASE FOLLOW LOCAL ORDINANCES OR REGULATION FOR DISPOSAL 当該液晶ディスプレイパネルは蛍光管が組み込まれていますので、地方自冶体の条 例、または、規則に従って廃棄ください。 9) This specification document’s Japanese language version is also available. Its Number (SPEC. No.) is LD-15712B. 10) When any question or issue occurs, it shall be solved by mutual discussion. 、 LD-16Z09-20 14. Carton storage condition Temperature 0℃ to 40℃ Humidity 95%RH or less Reference condition : : 20℃ to 35℃ , 85%RH or less 5℃ to 15℃ , 85%RH or less (summer) (winter) ・the total storage time (40℃,95%RH) : 240H or less Sunlight Be sure to shelter a product from the direct sunlight. Atmosphere Harmful gas, such as acid and alkali which bites electronic components and/or wires must not be detected. Notes Be sure to put cartons on palette or base, don’t put it on floor, and store them with removing from wall Please take care of ventilation in storehouse and around cartons, and control changing temperature is within limits of natural environment Storage period 1 year