Gleichmann & Co. Electronics GmbH Product Marketing Displays & Systems Industriestr. 16, D- 76297 Stutensee Tel :07249-910-0, Fax: 07249-910-559 http://www.msc-ge.com TFT COLOR LCD MODULE NL10276BC30-17 38cm (15.0 Type) XGA LVDS interface (1port) PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) All information is subject to change without notice. Please confirm the sales representative before starting to design your system. Document Number: DOD-PD-0568 (1st edition) Published date: July 2004 CP(N) 1 © NEC LCD Technologies, Ltd. 2004 All rights reserved. NL10276BC30-17 INTRODUCTION No part of this document shall be copied in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a product described herein or any other liability arising from use of such application. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or of others. While NEC Corporation has been making continuous effort to enhance the reliability of its products, the possibility of failures cannot be eliminated entirely. To minimize risks of damage to property or injury to person arising from a failure in an NEC product, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. NEC products are classified into the following three quality grades: "Standard", "Special", "Specific" The "Specific" quality grade applies only to applications developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a product depend on its quality grade, as indicated below. Customers must check the quality grade of each application before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Military systems, aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems (medical equipment, etc.) and any other equipment The quality grade of this product is "Standard" unless otherwise specified in this document. If customers intend to use this product for applications other than those specified for "Standard" quality grade, they should contact NEC Corporation sales representative in advance. PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 2 NL10276BC30-17 CONTENTS INTRODUCTION ..........................................................................................................................................2 1. OUTLINE....................................................................................................................................................4 1.1 STRUCTURE AND PRINCIPLE...........................................................................................................4 1.2 APPLICATIONS.....................................................................................................................................4 1.3 FEATURES.............................................................................................................................................4 2. GENERAL SPECIFICATIONS ................................................................................................................5 3. BLOCK DIAGRAM ...................................................................................................................................6 4. DETAILED SPECIFICATIONS ...............................................................................................................7 4.1 MECHANICAL SPECIFICATIONS......................................................................................................7 4.2 ABSOLUTE MAXIMUM RATINGS ....................................................................................................7 4.3 ELECTRICAL CHARACTERISTICS...................................................................................................8 4.3.1 LCD panel signal processing board ...............................................................................................8 4.3.2 Backlight lamp ...............................................................................................................................9 4.3.3 Power supply voltage ripple.........................................................................................................10 4.3.4 Fuse..............................................................................................................................................10 4.4 POWER SUPPLY VOLTAGE SEQUENCE ........................................................................................ 11 4.5 CONNECTIONS AND FUNCTIONS FOR INTERFACE PINS.........................................................12 4.5.1 LCD panel signal processing board .............................................................................................12 4.5.2 Backlight lamp .............................................................................................................................13 4.5.3 Position of plug and socket ..........................................................................................................13 4.5.4 Connection between receiver and transmitter for LVDS .............................................................14 4.6 DISPLAY COLORS AND INPUT DATA SIGNALS ..........................................................................16 4.7 DISPLAY POSITIONS.........................................................................................................................17 4.8 SCANNING DIRECTIONS .................................................................................................................17 4.9 INPUT SIGNAL TIMINGS..................................................................................................................18 4.9.1 Outline of input signal timings ....................................................................................................18 4.9.2 Timing characteristics ..................................................................................................................19 4.9.3 Input signal timing chart ..............................................................................................................20 4.10 OPTICS...............................................................................................................................................21 4.10.1 Optical characteristics................................................................................................................21 4.10.2 Definition of contrast ratio.........................................................................................................22 4.10.3 Definition of luminance uniformity ...........................................................................................22 4.10.4 Definition of response times ......................................................................................................22 4.10.5 Definition of viewing angles......................................................................................................22 5. RELIABILITY TESTS.............................................................................................................................23 6. PRECAUTIONS .......................................................................................................................................24 6.1 MEANING OF CAUTION SIGNS ......................................................................................................24 6.2 CAUTIONS ..........................................................................................................................................24 6.3 ATTENTIONS ....................................................................................................................................24 6.3.1 Handling of the product ...............................................................................................................24 6.3.2 Environment.................................................................................................................................25 6.3.3 Characteristics..............................................................................................................................25 6.3.4 Other ............................................................................................................................................25 7. OUTLINE DRAWINGS ...........................................................................................................................26 7.1 FRONT VIEW ......................................................................................................................................26 7.2 REAR VIEW ........................................................................................................................................27 REVISION HISTORY .................................................................................................................................28 PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 3 NL10276BC30-17 1. OUTLINE 1.1 STRUCTURE AND PRINCIPLE Color LCD module NL10276BC30-17 is composed of the amorphous silicon thin film transistor liquid crystal display (a-Si TFT LCD) panel structure with driver LSIs for driving the TFT (Thin Film Transistor) array and a backlight. The a-Si TFT LCD panel structure is injected liquid crystal material into a narrow gap between the TFT array glass substrate and a color-filter glass substrate. Color (Red, Green, Blue) data signals from a host system (e.g. PC, signal generator, etc.) are modulated into best form for active matrix system by a signal processing board, and sent to the driver LSIs which drive the individual TFT arrays. The TFT array as an electro-optical switch regulates the amount of transmitted light from the backlight assembly, when it is controlled by data signals. Color images are created by regulating the amount of transmitted light through the TFT array of red, green and blue dots. 1.2 APPLICATIONS • For industrial use 1.3 FEATURES • • • • • • • • Ultra-wide viewing angle (Adoption of Super Advanced -Super Fine TFT (SA-SFT)) LVDS interface (8-bit) Selectable LVDS input map Wide color gamut High contrast Small foot print Edge light type backlight (without inverter) Replaceable lamp for backlight PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 4 NL10276BC30-17 2. GENERAL SPECIFICATIONS Display area 304.128 (H) × 228.096 (V) mm Diagonal size of display 38.0 cm (15.0 inches) Drive system a-Si TFT active matrix Display color 16,777,216 colors (6bit+FRC) Pixel 1,024 (H) × 768 (V) pixels Pixel arrangement RGB (Red dot, Green dot, Blue dot) vertical stripe Dot pitch 0.099 (H) × 0.297 (V) mm Pixel pitch 0.297 (H) × 0.297 (V) mm Module size 326.5 (typ., W) × 253.5 (typ., H) × 17.0 (max., D) mm Weight TBD g (typ.) Contrast ratio (450):1 (typ.) Viewing angle At the contrast ratio ≥ 10:1 • Horizontal: Right side 85° (typ.), Left side 85° (typ.) • Vertical: Up side 85° (typ.), Down side 85° (typ.) Designed viewing direction Viewing angle with optimum grayscale (γ=2.2): normal axis (perpendicular) Polarizer surface Antiglare Polarizer pencil-hardness TBD H (min.) [by JIS K5600] Color gamut At LCD panel center 72 % (typ.) [against NTSC color space] Response time Ton+Toff (10%←→ 90%) (25) ms (typ.) Luminance At IBL=(6.0)mArms / lamp (300) cd/m2 (typ.) Signal system LVDS 1port (Receiver: Equivalent of THC63LVDF84A, THine Electronics Inc.) [8-bit digital signals for data of RGB colors, Dot clock (CLK), Data enable (DE)] Power supply voltage LCD panel signal processing board: 3.3V Edge light type: 4 cold cathode fluorescent lamps (without inverter) Backlight Power consumption Replaceable part • Lamp holder set: Type No. TBD At IBL=(6.0)mArms / lamp and checkered flag pattern TBD W (typ., Power dissipation of the inverter does not include.) PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 5 NL10276BC30-17 3. BLOCK DIAGRAM LCD module (Product) D1+ D1- 100Ω D2+ D2- 100Ω D3+ D3- 100Ω CLK+ CLK- H-driver 3,072 lines LCD panel 100Ω 768 lines 100Ω V-driver D0+ D0- Controller with receiver for LVDS Host H: 1,024 × 3 (R,G, B) V: 768 MSL +3.3V Power supply for gradation GND Note1 Note2 VCC FG Note1 Note2 Fuse DC/DC converter LCD panel signal processing board Backlight (Edge light type) 2 lamps VBLH VBLC Note1 2 lamps VBLH VBLC Note1 Note1: Connections between GND (Signal ground), FG (Frame ground) and VBLC (Lamp low voltage terminal) in the product GND – FG Connected GND - VBLC Not connected FG - VBLC Not connected Note2: GND and FG must be connected to customer equipment's ground, and it is recommended that GND, FG and customer inverter ground are connected together in customer equipment. PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 6 NL10276BC30-17 4. DETAILED SPECIFICATIONS 4.1 MECHANICAL SPECIFICATIONS Parameter Specification Unit 326.5 ± 0.5 (W) × 253.5 ± 0.5 (H) × 17.0 max. (D) Module size 304.128 (H) × 228.096 (V) Display area Weight Note1, Note2 mm Note1 mm TBD (typ.), TBD (max.) g Note1: Excluding lamp cables. Note2: See "7. OUTLINE DRAWINGS". 4.2 ABSOLUTE MAXIMUM RATINGS Parameter Power supply voltage LCD panel signal processing board Symbol Rating Unit VCC (-0.3 to +3.6) V Remarks Ta = 25°C Lamp voltage VBLH TBD Vrms VD V Ta = 25°C VF (-0.3 to +3.6) and <VCC +0.3 Tst -20 to +60 °C - Front surface TopF 0 to +55 °C Note3 Rear surface TopR TBD °C Note4 ≤ 95 % Ta ≤ 40°C ≤ 85 % 40 < Ta ≤ 50°C ≤ 70 % 50 < Ta ≤ 55°C Display signals Note1 Function signals Note2 Input voltage for signals Storage temperature Operating temperature Relative humidity Note5 RH Absolute humidity Note5 AH ≤ 73 Note6 g/m3 Ta > 55°C Operating altitude - ≤ (4,850) m 0°C≤ Ta ≤ 55°C Storage altitude - ≤ (13,600) m -20°C≤ Ta ≤ 60°C Note1: Display signals are D0+/-, D1+/-, D2+/-, D3+/- and CK+/-. Note2: Function signal is MSL. Note3: Measured at center of LCD panel surface (including self-heat) Note4: Measured at center of LCD module's rear shield surface (including self-heat) Note5: No condensation Note6: Water amount at Ta = 55°C and RH = 70% PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 7 NL10276BC30-17 4.3 ELECTRICAL CHARACTERISTICS 4.3.1 LCD panel signal processing board (Ta = 25°C) Parameter Symbol min. typ. max. Unit Remarks Power supply voltage VCC 3.0 3.3 3.6 V - Power supply current ICC - TBD Note1 TBD Note2 mA at VCC = 3.3V Permissible ripple voltage VRP - - 100 mVp-p for VCC High VTH - - +100 mV Low VTL -100 - - mV Input voltage swing for LVDS receiver Vi 0 - 2.4 V - Terminating resistance RT - 100 - Ω - High VFH 2.0 - VCC V Low VFL 0 - 0.8 V Differential input threshold voltage for LVDS receiver Input voltage for MSL signal at VCM=1.2V Note3 - Note1: Checkered flag pattern [by EIAJ ED-2522] Note2: Pattern for maximum current Note3: Common mode voltage for LVDS receiver PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 8 NL10276BC30-17 4.3.2 Backlight lamp (Ta=25°C, Note1) Parameter Symbol min. typ. max. Unit Lamp current IBL TBD (6.0) TBD mArms Lamp voltage VBLH - (650) - Vrms TBD - - Vrms TBD - - Vrms TBD (54) TBD kHz Lamp starting voltage VS Lamp oscillation frequency FO Remarks at IBL=(6.0)mArms: L=(300)cd/m2(typ.) Note3 Note2, Note3 Ta = 0°C Note2, Note3 Ta = 25°C Note2, Note3 Note4 Note1: This product consists of 4 backlight lamps, and these specifications are for each lamp. Note2: The lamp voltage cycle between lamps should be kept on a same phase. "VS" and "VBLH" are the voltage value between low voltage side (Cold) and high voltage side (Hot). Note3: The asymmetric ratio of working waveform for lamps (Lamp voltage peak ratio, Lamp current peak ratio and waveform space ratio) should be less than 5 % (See the following figure.). If the waveform is asymmetric, DC (Direct current) element apply into the lamp. In this case, a lamp lifetime may be shortened, because a distribution of a lamp enclosure substance inclines toward one side between low voltage terminal (Cold terminal) and high voltage terminal (Hot terminal). When designing the backlight inverter, evaluate asymmetric of lamp working waveform sufficiently. Pa Sa 0 Sb Pb ⏐Pa - Pb⏐ × 100 ≤ 5 % Pb ⏐Sa - Sb⏐ × 100 ≤ 5 % Sb Pa: Supply voltage/current peak for positive, Pb: Supply voltage/current peak for negative Sa: Waveform space for positive part, Sb: Waveform space for negative part Note4: In case "FO" is not the recommended value, beat noise may display on the screen, because of interference between "FO" and "1/th". Recommended value of "FO" is as following. FO = 1 1 × (2n-1) × th 4 th: Horizontal signal period (See "4.9.2 Timing characteristics".) n: Natural number (1, 2, 3 ⋅⋅⋅⋅⋅⋅⋅⋅) Note5: Method of lamp cable installation may invite fluctuation of lamp current and voltage or asymmetric of lamp working waveform. When designing method of lamp cable installation, evaluate the fluctuation of lamp current, voltage and working waveform sufficiently. PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 9 NL10276BC30-17 4.3.3 Power supply voltage ripple This product works, even if the ripple voltage levels are beyond the permissible values as following the table, but there might be noise on the display image. Power supply voltage VCC Ripple voltage Note1 (Measure at input terminal of power supply) Unit ≤ 100 mVp-p 3.3 V Note1: The permissible ripple voltage includes spike noise. 4.3.4 Fuse Fuse Parameter Rating Type Supplier TBD TBD Fusing current Remarks TBD Note1 TBD VCC TBD Note1: The power supply capacity should be more than the fusing current. If the power supply capacity is less than the fusing current, the fuse may not blow for a short time, and then nasty smell, smoking and so on may occur. PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 10 NL10276BC30-17 4.4 POWER SUPPLY VOLTAGE SEQUENCE ON 3.0V VCC Note1 OFF 2.5V 0V 3.0V (0.1ms < Tr < 80ms) (20ms max.) (Toff > 200ms) Display signals* Function signal Note2 0V VALID period (35 < t < 50ms) (10 < t < 35ms) * These signals should be measured at the terminal of 100Ω resistance. Note1: In terms of voltage variation (voltage drop) while VCC rising edge is below 3.0V, a protection circuit may work, and then this product may not work. Note2: Display signals (D0+/-, D1+/-, D2+/-, D3+/- and CK+/-) and function signal (MSL) must be "0" voltage, exclude the VALID period (See above sequence diagram). If these signals are higher than 0.3V, the internal circuit is damaged. If some of display and function signals of this product are cut while this product is working, even if the signal input to it once again, it might not work normally. If customer stops the display and function signals, they should be cut VCC. Note3: VCC should be 3.0V or more while VCC ON period. Note4: The backlight power supply voltage should be inputted within the valid period of display and function signals, in order to avoid unstable data display. PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 11 NL10276BC30-17 4.5 CONNECTIONS AND FUNCTIONS FOR INTERFACE PINS 4.5.1 LCD panel signal processing board CN1 socket (LCD module side): DF-14H-20P-1.25H (Hirose Electric Co., Ltd. (HRS)) Adaptable plug: DF14-20S-1.25C (Hirose Electric Co., Ltd. (HRS)) Pin No. Symbol Signal Remarks 1 VCC 2 VCC Power supply Note1 3 GND 4 GND Ground Note1 5 D0- 6 D0+ Pixel data Note2 7 GND Ground Note1 8 D1- 9 D1+ Pixel data Note2 10 GND Ground Note1 11 D2- 12 D2+ Pixel data Note2 13 GND Ground Note1 14 CLK- 15 CLK+ Pixel clock Note2 16 GND Ground Note1 17 D3- 18 D3+ Pixel data Note2 19 GND Ground Note1 20 MSL Selection of LVDS input map Note3 High: Input map A Low or Open: Input map B Note1: All GND and VCC terminals should be used without any non-connected lines. Note2: Twist pair wires with 100Ω (Characteristic impedance) should be connected between LCD panel signal processing board and LVDS transmitter. Note3: See "4.5.4 Connection between receiver and transmitter for LVDS". PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 12 NL10276BC30-17 4.5.2 Backlight lamp Attention: VBLH and VBLC must be connected correctly. If customer connects wrongly, customer will be hurt and the product will be broken. CN201 plug (LCD module side): BHR-03VS-1 (J.S.T Mfg. Co., Ltd.) Adaptable socket: SM02(8.0)B-BHS-1-TB (J.S.T Mfg. Co., Ltd.) Pin No. 1 2 3 Symbol VBLH N.C. VBLC Signal High voltage terminal (Hot) Low voltage terminal (Cold) Remarks Cable color: (Pink) Keep this pin Open. Cable color: (White) CN202 plug (LCD module side): BHR-03VS-1 (J.S.T Mfg. Co., Ltd.) Adaptable socket: SM02(8.0)B-BHS-1-TB (J.S.T Mfg. Co., Ltd.) Pin No. 1 2 3 Symbol VBLH N.C. VBLC Signal High voltage terminal (Hot) Low voltage terminal (Cold) Remarks Cable color: (Pink) Keep this pin Open. Cable color: (White) CN203 plug (LCD module side): BHR-03VS-1 (J.S.T Mfg. Co., Ltd.) Adaptable socket: SM02(8.0)B-BHS-1-TB (J.S.T Mfg. Co., Ltd.) Pin No. 1 2 3 Symbol VBLH N.C. VBLC Signal High voltage terminal (Hot) Low voltage terminal (Cold) Remarks Cable color: (Pink) Keep this pin Open. Cable color: (White) CN204 plug (LCD module side): BHR-03VS-1 (J.S.T Mfg. Co., Ltd.) Adaptable socket: SM02(8.0)B-BHS-1-TB (J.S.T Mfg. Co., Ltd.) Pin No. 1 2 3 Symbol VBLH N.C. VBLC Signal High voltage terminal (Hot) Low voltage terminal (Cold) Remarks Cable color: (Pink) Keep this pin Open. Cable color: (White) 4.5.3 Position of plug and socket Rear side CN201 1 3 CN202 1 3 Signal processing board CN1 20 CN203 3 1 CN204 3 1 1 Insert direction PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 13 NL10276BC30-17 4.5.4 Connection between receiver and transmitter for LVDS (1) Input LVDS map A (MSL: "High") LCD module (Product) Host Note2 Note3 R2 TA0 1 R3 TA1 2 VCC R4 TA2 3 GND R5 TA3 4 GND R6 TA4 TA- 5 D0- RA- R7 TA5 TA+ 6 D0+ RA+ G2 TA6 7 GND VCC GND 8 D1- RB+ 9 D1+ RB- 10 GND TC- 11 D2- RC+ TC+ 12 D2+ RC- TBG3 TB0 G4 TB1 G5 TB2 G6 TB3 G7 TB4 13 GND B2 TB5 TCLK- 14 CLK- RCLK- B3 TB6 TCLK+ 15 CLK+ RCLK+ 16 GND TB+ B4 TC0 TD- B5 TC1 TD+ B6 17 D3- RD- 18 D3+ RD+ TC2 19 GND 20 MSL B7 TC3 Note4 TC4 Note4 TC5 DE TC6 R0 TD0 R1 TD1 G0 TD2 G1 TD3 B0 TD4 B1 TD5 CLK Signal processor Receiver for LVDS CN1 Socket Equivalent of THC63LVDF84A MSL VCC LCD controller GND CLK IN LVDS transmitter Note1 VCC GND MSL (High) LCD panel signal processing board Note1: Recommended transmitter: THC63LVDF83A, THC63LVDM83R (THine Electronics Inc.). or equivalent Note2: LSB (Least Significant Bit) – R0, G0, B0 MSB (Most Significant Bit) – R7, G7, B7 Note3: Twist pair wires with 100Ω (Characteristic impedance) should be connected between LCD panel signal processing board and LVDS transmitter. Note4: Input signals to TC4 and TC5 are not used inside the product, but do not keep TC4 and TC5 open to avoid noise problem. PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 14 NL10276BC30-17 (2) Input LVDS map B (MSL: "Low" or "Open") Host LCD module (Product) Note2 Note3 R0 TXIN0 1 VCC R1 TXIN1 2 VCC R2 TXIN2 3 GND R3 TXIN3 4 GND R4 TXIN4 TXOUT0- 5 D0- RA- R5 TXIN6 TXOUT0+ 6 D0+ RA+ G0 TXIN7 7 GND GND TXOUT1- 8 D1- RB+ TXOUT1+ 9 D1+ RB- G1 TXIN8 G2 TXIN9 10 GND G3 TXIN12 TXOUT2- 11 D2- RC+ G4 TXIN13 TXOUT2+ 12 D2+ RC- G5 TXIN14 13 GND B0 TXIN15 TXCLKOUT- 14 CLK- RCLK- B1 TXIN18 TXCLKOUT+ 15 CLK+ RCLK+ 16 GND B2 TXIN19 TXOUT3- 17 D3- RD- B3 TXIN20 TXOUT3+ 18 D3+ RD+ B4 TXIN21 19 GND B5 TXIN22 20 MSL Note4 TXIN24 Note4 TXIN25 DE TXIN26 R6 TXIN27 R7 TXIN5 G6 TXIN10 G7 TXIN11 B6 TXIN16 B7 TXIN18 CLK CLK IN Signal processor Receiver for LVDS CN1 Socket Equivalent of THC63LVDF84A MSL VCC LCD controller GND Transmitter for LVDS DS90C383 Note1 VCC GND LCD panel signal processing board MSL (Low or Open) Note1: Recommended transmitter: DS90C383 (National Semiconductor) or equivalent Note2: LSB (Least Significant Bit) – R0, G0, B0 MSB (Most Significant Bit) – R7, G7, B7 Note3: Twist pair wires with 100Ω (Characteristic impedance) should be connected between LCD panel signal processing board and LVDS transmitter. Note4: Input signals to TC4 and TC5 are not used inside the product, but do not keep TC4 and TC5 open to avoid noise problem. PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 15 NL10276BC30-17 4.6 DISPLAY COLORS AND INPUT DATA SIGNALS This product can display in equivalent to 16,777,216 colors in 256 gray scales. Also the relation between display colors and input data signals is as the following table. Data signal (0: Low level, 1: High level) Display colors R7 R6 R5 R4 R3 R2 R1 R0 Black Basic Colors Blue Red Magent a Green Cyan Yellow White Red gray scale Black dark bright Red Green gray scale 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ Black dark ↑ ↓ bright Green Black Blue gray scale 0 0 1 1 0 0 1 1 dark ↑ ↓ bright Blue 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 0 0 0 0 0 0 0 : : 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 1 1 G7 G6 G5 G4 G3 G2 G1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 G0 B7 B6 B5 B4 B3 B2 B1 B0 0 0 0 0 1 1 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 1 1 1 1 1 1 1 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 1 1 0 1 1 16 NL10276BC30-17 4.7 DISPLAY POSITIONS The following table is the coordinates per pixel (See "4.8 SCANNING DIRECTIONS".). C (1, 1) R G B C( 1, 1) C( 2, 1) ••• C( X, 1) ••• C(1023, 1) C(1024, 1) C( 1, 2) C( 2, 2) ••• C( X, 2) ••• C(1023, 2) C(1024, 2) • • • C( 1, • • • Y) C( • • • 2, • ••• • ••• Y) • • • • ••• • • • • C( X, • ••• • Y) ••• • • • C(1023, • ••• • Y) C(1024, • • • • ••• • • • • • • • Y) C( 1, 767) C( 2, 767) ••• C( X, 767) ••• C(1023, 767) C(1024, 767) C( 1, 768) C( 2, 768) ••• C( X, 768) ••• C(1023, 768) C(1024, 768) 4.8 SCANNING DIRECTIONS The following figures are seen from a front view. Also the arrow shows the direction of scan. C (1, 1) D (1, 1) C (1024, 1) D (1024, 1) Note1 C (1, 768) D (1, 768) C (1024, 768) D (1024, 768) Note1: Meaning of C (X, Y) and D (X, Y) C (X, Y): The coordinates of the display position (See "4.7 DISPLAY POSITIONS".) D (X, Y): The data number of input signal for LCD panel signal processing board PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 17 NL10276BC30-17 4.9 INPUT SIGNAL TIMINGS 4.9.1 Outline of input signal timings • Horizontal signal Note1 Horizontal display period (thd) DE (Data enable) Display period • Vertical signal Note1 Vertical display period (tvd) DE (Data enable) 1 2 3 4 768 Note2 Display period Note1: This diagram indicates virtual signal for set up to timing. Note2: See "4.9.3 Input signal timing chart" for numeration of pulse. PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 18 NL10276BC30-17 4.9.2 Timing characteristics (Note1) Parameter CLK DATA Frequency Duty Rise time, Fall time Setup time CLK-DATA Hold time Rise time, Fall time Horizontal DE Vertical (One frame) Symbol min. typ. max. Unit Remarks 1/tc - TBD (65.0) TBD MHz ns ns ns ns µs CLK CLK ms H H ns ns ns 15.384 ns (typ.) Cycle th Display period thd Cycle Display period Setup time CLK-DE Hold time Rise time, Fall time tv tvd - - TBD TBD TBD TBD (20.676) (1,344) (1,024) (16.666) (806) (768) - TBD TBD - Note2 Note2 48.363 kHz (typ.) Note3 60.0 Hz (typ.) Note2 Note1: Definition of parameters is as follows. tc = 1CLK, th = 1H Note2: See the data sheet of LVDS transmitter. Note3: "th" must keep the fluctuation within ±1 CLK, because of avoidance of image sticking. PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 19 NL10276BC30-17 4.9.3 Input signal timing chart Horizontal timing tc CLK DATA (R0-R7) (G0-G7) (B0-B7) Invalid 1 2 1023 1024 Invalid DE thd th Vertical timing DATA (R0-R7) (G0-G7) (B0-B7) Invalid Invalid 1 2 767 768 DE tvd tv PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 20 NL10276BC30-17 4.10 OPTICS 4.10.1 Optical characteristics (Note1, Note2) Parameter Condition White at center θR = 0°, θL = 0°, θU = 0°, θD = 0° White/Black at center Contrast ratio θR = 0°, θL = 0°, θU = 0°, θD = 0° White Luminance uniformity θR = 0°, θL = 0°, θU = 0°, θD = 0° x coordinate White y coordinate x coordinate Red y coordinate Chromaticity x coordinate Green y coordinate x coordinate Blue y coordinate θR = 0°, θL = 0°, θU = 0°, θD = 0° Color gamut at center, against NTSC color space Black to white Response time White to black Ton+Toff Right θU = 0°, θD = 0°, CR ≥ 10 Left Viewing θU = 0°, θD = 0°, CR ≥ 10 angle Up θR = 0°, θL = 0°, CR ≥ 10 Down θR = 0°, θL = 0°, CR ≥ 10 Luminance Symbol min. typ. max. Unit L TBD (300) - cd/m2 CR TBD (450) - - LU - (1.1) 1.3 - Wx Wy Rx Ry Gx Gy Bx By TBD TBD - 0.313 0.329 TBD TBD TBD TBD TBD TBD TBD TBD - - C TBD 72 - % Ton Toff TBD TBD TBD TBD TBD TBD (25) 85 85 85 85 TBD TBD - ms ms ms ° ° ° ° θR θL θU θD Measuring Remarks instrument BM5A or SR-3 BM5A Note3 or SR-3 BM-5A Note4 SR-3 Note5 BM-5A Note6 Note7 BM-5A Note8 Note1: These are initial characteristics. Note2: Measurement conditions are as follows. Ta = 25°C, VCC = 3.3V, IBL = (6.0)mArms/lamp, Display mode: XGA, Horizontal cycle = 48.363kHz, Vertical cycle = 60.0Hz Optical characteristics are measured at luminance saturation after 20minutes from working the product, in the dark room. Also measurement method for luminance is as follows. 50cm Photodetector (TOPCON BM-5A, SR-3) LCD module (Product) 1° Note3: See "4.10.2 Definition of contrast ratio". Note4: See "4.10.3 Definition of luminance uniformity". Note5: These coordinates are found on CIE 1931 chromaticity diagram. Note6: Product surface temperature: TopF = TBD°C Note7: See "4.10.4 Definition of response times". Note8: See "4.10.5 Definition of viewing angles". PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 21 NL10276BC30-17 4.10.2 Definition of contrast ratio The contrast ratio is calculated by using the following formula. Luminance of white screen Contrast ratio (CR) = Luminance of black screen 4.10.3 Definition of luminance uniformity The luminance uniformity is calculated by using following formula. Maximum luminance from ① to ⑤ Luminance uniformity (LU) = Minimum luminance from ① to ⑤ The luminance is measured at near the 5 points shown below. 171 512 853 ② ① 126 ③ 384 ⑤ ④ 640 4.10.4 Definition of response times Response time is measured, the luminance changes from "white" to "black", or "black" to "white" on the same screen point, by photo-detector. Ton is the time it takes the luminance change from 90% down to 10%. Also Toff is the time it takes the luminance change from 10% up to 90% (See the following diagram.). White 100% 90% Luminance Black 10% 0% Ton Toff 4.10.5 Definition of viewing angles Normal axis (Perpendicular) 12 o’clock θL Left θU Upper θR θD Lower Right PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 22 NL10276BC30-17 5. RELIABILITY TESTS Test item Condition Judgement Note1 High temperature and humidity (Operation) Heat cycle (Operation) Thermal shock (Non operation) No display malfunctions ESD (Operation) Dust (Operation) TBD Vibration (Non operation) No display malfunctions No physical damages Mechanical shock (Non operation) operation Low pressure No display malfunctions non-operation Note1: Display and appearance are checked under environmental conditions equivalent to the inspection conditions of defect criteria. Note2: See the following figure for discharge points. ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ ⃝ PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 23 NL10276BC30-17 6. PRECAUTIONS 6.1 MEANING OF CAUTION SIGNS The following caution signs have very important meaning. Be sure to read "6.2 CAUTIONS" and "6.3 ATTENTIONS", after understanding these contents! ! This sign has the meaning that customer will be injured by himself or the product will sustain a damage, if customer has wrong operations. This sign has the meaning that customer will get an electrical shock, if customer has wrong operations. This sign has the meaning that customer will be injured by himself, if customer has wrong operations. 6.2 CAUTIONS ∗ Do not touch the working backlight. Customer will be in danger of an electric shock. ∗ Do not touch the working backlight. Customer will be in danger of burn injury. ∗ Do not shock and press the LCD panel and the backlight! There is a danger of breaking, because they are made of glass. (Shock: To be not greater TBD m/s2 and to be not greater TBD ms, Pressure: To be not greater TBD N) 6.3 ATTENTIONS ! 6.3.1 Handling of the product ① Take hold of both ends without touch the circuit board cover when customer pulls out products (LCD modules) from inner packing box. If customer touches it, products may be broken down or out of adjustment, because of stress to mounting parts. ② Do not hook cables nor pull connection cables such as lamp cable and so on, for fear of damage. ③ If customer puts down the product temporarily, the product puts on flat subsoil as a display side turns down. ④ Take the measures of electrostatic discharge such as earth band, ionic shower and so on, when customer deals with the product, because products may be damaged by electrostatic. ⑤ The torque for mounting screws must never exceed TBD N⋅m. Higher torque values might result in distortion of the bezel. ⑥ The product must be installed using mounting holes without undue stress such as bends or twist (See outline drawings). And do not add undue stress to any portion (such as bezel flat area) except mounting hole portion. Bends or twist described above and undue stress to any portion except mounting hole portion may cause display un-uniformity. ⑦ Do not press or rub on the sensitive display surface. If customer clean on the panel surface, NEC recommends using the cloth with ethanolic liquid such as screen cleaner for LCD. PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 24 NL10276BC30-17 ⑧ Do not push-pull the interface connectors while the product is working, because wrong power sequence may break down the product. ⑨ Do not bend or unbend the lamp cable at the near part of the lamp holding rubber, to avoid the damage for high voltage side of the lamp. This damage may cause a lamp breaking and abnormal operation of high voltage circuit. ⑩ When installing the lamp cable, do not attach the lamp cable on the metal part of the LCD module directly. This may cause leakage high frequency current to the metal part, then the brightness may decrease or the lamp may not light. ⑪ When not connecting FG of the LCD module to the customer's equipment ground, inverter noise may create a beat frequency that will cause video noise on the LCD screen. ⑫ When customer deals with the product, use of an original protection sheet on the product surface (polarizer) is recommended for protection of panel surface. Adhesive type protection sheet may change color or properties of the polarizer. 6.3.2 Environment ① Do not operate or store in high temperature, high humidity, dewdrop atmosphere or corrosive gases. Keep the product in antistatic pouch in room temperature, because of avoidance for dusts and sunlight, if customer stores the product. ② In order to prevent dew condensation occurring by temperature difference, the product packing box must be opened after leave under the environment of an unpacking room temperature enough. Because a situation of dew condensation occurring is changed by the environmental temperature and humidity, evaluate the leaving time sufficiently. (Recommendation leaving time: 6 hour or more with packing state) ③ Do not operate in high magnetic field. Circuit boards may be broken down by it. ④ This product is not designed as radiation hardened. 6.3.3 Characteristics The following items are neither defects nor failures. ① Response time, luminance and color may be changed by ambient temperature. ② The LCD may be seemed luminance non-uniformity, flicker, vertical seam or small spot by display patterns. ③ Optical characteristics (e.g. luminance, display uniformity, etc.) gradually is going to change depending on operating time, and especially low temperature, because the LCD has cold cathode fluorescent lamps. ④ Do not display the fixed pattern for a long time because it may cause image sticking. Use a screen saver, if the fixed pattern is displayed on the screen. ⑤ The display color may be changed by viewing angle because of the use of condenser sheet in the backlight. ⑥ Optical characteristics may be changed by input signal timings. ⑦ The interference noise of input signal frequency for this product's signal processing board and luminance control frequency of customer's backlight inverter may appear on a display. Set up luminance control frequency of backlight inverter so that the interference noise does not appear. 6.3.4 Other ① All GND and VCC terminals should be used without any non-connected lines. ② Do not disassemble a product or adjust variable resistors without permission of NEC. ③ See "REPLACEMENT MANUAL FOR LAMP HOLDER SET", if customer would like to replace backlight lamps. ④ Pay attention not to insert waste materials inside of products, if customer uses screwnails. ⑤ Pack the product with original shipping package, because of avoidance of some damages during transportation, when customer returns it to NEC for repair and so on. ⑥ The LCD module by itself or integrated into end product should be packed and transported with display in the vertically position. Otherwise the display characteristics may be impaired. PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) 25 NL10276BC30-17 7. OUTLINE DRAWINGS 7.1 FRONT VIEW Note1: The values in parentheses are for reference. Note2: Not shown tolerances of the dimensions are TBD mm. Note3: The torque for mounting screws must never exceed TBD N⋅m. PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) Unit: mm 26 NL10276BC30-17 7.2 REAR VIEW Note1: The values in parentheses are for reference. Note2: Not shown tolerances of the dimensions are TBD mm. Note3: The torque for mounting screws must never exceed TBD N⋅m. PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) Unit: mm 27 NL10276BC30-17 REVISION HISTORY The inside of latest specifications is revised to the clerical error and the major improvement of previous edition. Only a changed part such as functions, characteristic value and so on that may affect a design of customers, are described especially below. Edition 1st edition Document number DOD-PD0568 Prepared date July 6, 2004 Revision contents and signature Revision contents New issue Signature of writer Approved by Checked by T. ITO PRELIMINARY DATA SHEET DOD-PD-0568 (1st edition) Prepared by R. KAWASHIMA 28