DOCUMENT NUMBER NCD-5DC2-01 SAA-1 Series Single-Mode FC ADAPTOR TECHNICAL SPECIFICATIONS Seiko Instruments Inc. Components Sales Dept. 8, Nakase 1-Chome Mihama-ku, Chiba-shi, Chiba-ken 261 JAPAN Telephone : 043-211 -1214 -1215 Facsimile : 043-211 -8035 SAA-1 Series Single-Mode FC ADAPTOR TECHNICAL SPECIFICATIONS Document Number NCD-5DC2-01 NAE63D01 " SAA-1 Part " May 1986 NAE63D02 " SAA-1 Part " September 1986 SSA930305 March 1993 39055-2016-01 September 1993 NCD-5DC2-01 December 1995 Copyright 1986, 1993, 1995 by Seiko Instruments Inc. All right reserved. The information contained herein shall not reproduced or disclosed to any third party without the express written consent of SII. The Specifications contained herein are subject to change without notice. SII is a trademark of Seiko Instruments Inc. Please address any questions, comments, and suggestions to: Seiko Instruments USA Inc. Seiko Instruments GmbH Electronics Components Division 2990 West Lomita Boulevard Torrance, CA 90505, U.S.A. Phone: 310-517-7780 Fax: 310-517-7792 OFC Division Siemensstraße 9b D-63263 Neu-Isenburg, Germany Phone: 06102-297-0 Fax: 06102-297-211 Seiko Instruments (H.K.) Ltd. Seiko Instruments Taiwan Inc. Sales Department 4th & 5th Floor, Wyler Center 2 200 Tai Lin Pai Road, Kwai Chung N.T., Kowloon, Hong Kong Phone: 852-2421-8611 Fax: 852-2480-5479 Sales Department 5F-1, No.99, Sec. 2, Chung Shan Rd. Taipei 104, Taiwan, R.O.C. Phone: 02-563-5001, 523-5111 Fax: 02-521-9519 Seiko Instruments Singapore pte. Ltd. 2, Marsiling Lane, Woodlands New Town, Singapore, 2573, Singapore Phone: 65-2691370 Fax: 65-2699729 ii TABLE OF CONTENTS Section 1. 1.1 Page PROVISION 1 Application Limit 1 2. PARTS NUMBER 1 3. GENERAL SPECIFICATIONS 2 3.1 Parts and Materials 2 3.2 Physical Dimensions 2 3.3 General Tolerances 2 3.4 Insertion Loss 3 4. PACKING 3 5. SHIPPING INSPECTION 3 Table Table 1 Parts Number 1 Table 2 Parts and Materials 2 Table 3 General Tolerance 2 Table 4 Insertion Loss and the Measurement Conditions 3 Figure Figure 1 Insertion Loss Measurement System 3 Figure 2 SAA-1 Adaptor 4 Figure 3 to 4 Part Dimensions 5 iii iv 1. PROVISION 1.1 Application Limit These specifications apply to the SAA-1 Single-Mode FC ADAPTOR supplied by SII. 2. PARTS NUMBER Parts Number of the Adaptor is Shown in Table 1. Table 1 Parts Number 1 3. GENERAL SPECIFICATIONS 3.1 Parts and Materials Parts and the materials are shown in Table 2. Table 2 Parts and materials No. ① ② ➂ -1 ➂ -2 ➃ ⑤ ➅ ⑦ -1 ⑦ -2 Part Name Q'ty Material Notes Housing A 1 Brass Nickel Plating Fitting Sleeve 2 Brass Nickel Plating Slit Sleeve 1 Spacer 1 Brass Nickel Plating Housing B 1 Brass Nickel Plating Screw 2 Brass Nickel Plating Cap 2 Plastic White Synthetic Rubber Red Phosphor Bronze -- Zirconia Ceramics 3.2 Physical Dimensions Figure 2 shows the SAA-1. Figure 3 to 4 show the part dimension. • In accordance with JIS C5970 F01 type connectors 3.3 General Tolerances Permissible deviation in dimensions without tolerance indication is in accordance with JIS B 0405 class m, as shown in Table 3. Table 3 General tolerance (JIS B 0405 class m) Basic size step (mm) Over Under Permissible deviation (mm) 0.5 3 ±0.1 3 6 ±0.1 6 30 ±0.2 30 120 ±0.3 2 3.4 Insertion Loss Insertion Loss of the adaptor and the measurement conditions shown in Table 4. Figure 1 shows the measurement system. Measured Adaptor Master Cord Light-Source Master Plug Master Plug Master Cord Optical Power Meter Photo Detector Figure 1 Insertion loss measurement system Table 4 Insertion loss and the measurement conditions Parts Number Insertion Loss Conditions SAA-1 1❑❑00 SAA-1 2❑❑00 ( Slit Sleeve : Phosphor Bronze ) ( Slit Sleeve : Zirconia Ceramics ) 0.7dB or Less 0.4dB or Less Light-Source LD or LED LD Wavelength Master Cord Terminated 1.3 µm 1.3 µm Flat Polishing with Buffing PC Polishing 4. PACKING The product is packed to prevent damage during shippment. 5. SHIPPING INSPECTION The insertion loss inspected before shipping. 3 with Marking ( ROGO ) Type without Marking ( ROGO ) Type Unit : mm FIgure 2 SAA-1 4 Unit : mm Figure 3 ⑦-1 Cap Unit : mm Figure 4 ⑦-2 Cap 5