Silan Semiconductors SC2128A REMOTE FAN CONTROL IC DESCRIPTION The SC2128A is a high performance electronic fan controller LSI, Speed control, off-timer, rhythm wind, sleep mode, head swing and/or light control are all built into a single chip. Indicator LED output, buzzer output, key control input, as well as remote control decoding circuitry are all provided to build a full function electronic fan with remote control capability having the highest performance with the least external components. Pin assignment and application circuit are optimized for easy PCB layout and cost saving for electronic fan application. FEATURES DIP-16 * High performance CMOS Technology * Low power consumption * Optional independent light control * 90 seconds cycle/6 seconds per step(off step 3 seconds) rhythm wind pattern * Built-in remote control decoding circuitry with mask option custom code * DIP or SO package(22 pin SO not available) * Up to 3 dependent/independent swing-head/light output * Available in 16,18,20,22,24 pin package for none, one set or two sets of swing head and/or light control * Four operation modes: ordinary, rhythm, ordinary sleep and rhythm sleep. * Memory start-up mode * 2-3 seconds middle wind start-up(mask option) APPLICATIONS * Optimized for fan application * Suitable for heater fan, cooling fan, and other home appliances with remote control, timer and/or output level control HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 1 2000.12.31 Silan Semiconductors SC2128A PIN CONFIGURATION LO VSS MI OSCI ST OSCO LED1 VDD OFF/MEMS/ BUZZ LED2 SC2128A 24 pin SO REMOTE 20 pin SO2 22 pin DIP 20 pin 18 pin 16 pin SW2 LED3 SPEED COM MODE TIMER SO1 SW1 LIGHT LIT NC NC ORDERING INFORMATION SC2128A- X X X X S = Swing Head Output(s) Controlled by a Single Key (Mask Option) D = Two Swing Head Outputs Controlled by Double Keys (D can be omitted) 0 = No Swing head Output 1 = 1 Swing head Output 2 = 2 Swing head Outputs 3 = 1 Swing head & Light Control Outputs 4 = 2 Swing head & Light Control Outputs 2 = 1/2/4 Hour, Non-Accumulated Timer 3 = 1/2/4 Hour, Accumulated Timer 4 = 0.5/1/2/4 Hour, Non-Accumulated Timer 5 = 0.5/1/2/4 Hour, Accumulated Timer 8 = 1/2/4/8 Hour, Non-Accumulated Timer 9 = 1/2/4/8 Hour, Accumulated Timer D = Non-Memory Start-up & Non-Middle Wind Start-up (Mask Option) C = Non-Memory Start-up & Middle Wind Start-up L = Memory Start-up & Non-Middle Wind Start-up (Mask Option) M = Memory Start-up & Middle Wind Start-up Note: SC2128A Standard ICs: SC2128A-C31, SC2128A-C51, SC2128A-C80, SC2128A-C81, SC2128A-C82, SC2128A-C83, SC2128A-C92. Other options are available upon request and require a minimum order Quantity. Please contact Silan or your local agent for details. HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 2 2000.12.31 Silan Semiconductors SC2128A BLOCK DIAGRAM VDD VSS OSCI OSC LO TIMING OSCO SPEED CONTROL MI ST REMOTE FILTER DECODER COM LED SCAN SPEED TIMER SW1 KEY SENSE SW2 OFF/MEMS/ BUZZ LED2 LED3 TIMER MODE LED1 SO1 MEMORY LIGHT SWING/ LIGHT SO2 LIT HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 3 2000.12.31 Silan Semiconductors SC2128A ABSOLUTE MAXIMUM RATINGS Characteristic Supply Voltage Input/Output Voltage Power Dissipation Symbol Test Conditions Value Unit VDD -- 0 ~ 6.0 V VI,VO VDD - VSS -0.3V ~ VDD+0.3V V PD VDD – VSS = 5.0 500 mW Operating Temperature Topr -- -20 ~ +70 °C Storage Temperature Tstg -- -40 ~ +125 °C ELECTRICAL CHARACTERISTICS Parameter Symbol Supply Voltage VDD Test conditions -- Min Typ Max Unit 4.0 5.0 6.0 V -- 134 200 µA VDD-1.5 -- -- V VDD=5.0V, Oscillator stops. Stand-by Current Iq All output floating, All input fixed to VDD. Input High Level Voltage VIH -- Input Low Level Voltage VIL -- -- -- 1.5 V Drive Current (COM) IOH VDD=5.0V, Vo=3.5V 15 21.5 -- mA Sink Current (COM) IOL VDD=5.0V, Vo=1.5V -12 -16.5 -- mA VDD=5.0V, Vo=3.5V 5 6.5 -- Drive Current (LED1, LED2, IOH mA LED3) Sink Current (LED1, LED2, LED3) IOL VDD=5.0V, Vo=1.5V -4 -5.7 -- mA Drive Current (OFF/BUZZ) IOH VDD=5.0V, Vo=2.5V 1.5 3.0 -- mA Sink Current (OFF/BUZZ) IOL VDD=5.0V, Vo=2.5V -2 -3.7 -- mA IOL VDD=5.0V, Vo=2.5V -6.5 -16 -- mA -- 32768 -- Hz Sink Current (LO,MI,ST,SO1, SO2,LIT) Oscillation frequency fOSC -- Key Press Duration Tkey -- 80 -- -- ms Remote Input Bit Duration Tbit -- 2.0 2.5 3.0 ms HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 4 2000.12.31 Silan Semiconductors SC2128A PIN DESCRIPTION Pin No. Symbol 16 18 PIN PIN 20 20 22 24 PIN PIN PIN PIN Note1 Note2 Note3 Note4 I/O Function VDD 5 5 5 6 6 6 -- Positive power supply VSS 2 2 2 3 3 3 -- Negative power supply COM 10 12 14 13 15 17 O Indicator LED common output LED1 13 15 17 16 18 20 O LED2 12 14 16 15 17 19 O LED3 11 13 15 14 16 18 O Indicator LED output pins SPEED 7 7 7 8 8 8 I SPEED key control input MODE 8 8 8 9 9 9 I MODE key control input TIMER 9 11 13 12 14 16 I TIMER key control input SW1 -- 9 9 10 10 10 I Swing head 1 control key input SW2 -- -- -- 1 1 1 I Swing head 2 control key input 6 6 6 7 7 7 I/O LIGHT -- -- 10 -- 11 11 I Light control key input SO1 -- 10 12 11 13 15 O Swing head 1 output SO2 -- -- -- 20 22 24 O Swing head 2 output LIT -- -- 11 -- 12 14 O Light output LO 16 18 20 19 21 23 O MI 15 17 19 18 20 22 O ST 14 16 18 17 19 21 O REMOTE 1 1 1 2 2 2 I Remote control sensor input OSCI 3 3 3 4 4 4 I Oscillator input pin OFF/MEMS/ BUZZ OFF control key input, shared with buzzer output Speed outputs OSCO 4 4 4 5 5 5 O Oscillator output pin NC -- -- -- -- -- 12 I No connection NC -- -- -- -- -- 13 I No connection Note1 : One swing head control plus light control type Note2 : Two Sets of Swing Head Control Type Note3 : DIP Package Only Note4 : SO Package Only HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 5 2000.12.31 Silan Semiconductors SC2128A FUNCTIONAL DESCRIPTION 1. CONTROL KEYS Up to seven function keys – SPEED, MODE, TIMER, SW1, SW2, LIGHT and OFF/MEMS – may be used on the control panel of fan to access SC2128A to its full versatility. OFF/MEMS key input pin serves further as buzzer output BUZZ pin. All key inputs are internally pulled-high in SC2128A. SPEED key controls the fan speed. TIMER key adjusts off-timer. MODE key sets fan into various modes of operation. SW1 and SW2 keys control the head swing of fan. LIGHT key toggles the LIT output ON and OFF. OFF/MEMS key resets the fan to idle state when fan is ON. It starts fan into memory mode if pressed when fan is OFF, provided memory option is enabled. LIT output is not affected by OFF key. 2. SPEED KEY SPEED key is used to (1) turn on the fan (2) change speed of the fan. OFF/MEMS may also be used to turn on the fan into memory mode, provided memory mode is enabled. SLEEP key my turn on the fan from remote control handset. All the other keys can NOT turn on the fan. All the other keys, except LIGHT key, can NOT operate until fan is turned on. The diagram shows the state transition of SC2128A for successive pressing of SPEED key. Y MI start EE SP ED LO=Z MI=L ST=Z D KE K EY OFF Y MID LO=L MI=Z ST=Z LOW LO=Z MI=Z ST=Z Z=high impedence L=low voltage LO=L MI=Z ST=Z SPEED KEY KE E SP S ED PE STR SPEED KEY D EE SP Y KE not middle wind start-up optioned LO=L MI=Z ST=Z 3. TIMER KEY TIMER key is used to set time schedule after which SC2128A will automatically restore off state(off-timer). When the fan is on, pressing TIMER key sets up the off-timer. Each pressing of TIMER key increases the timer by one step. Each time increment step is determined by various timer options. Either 0.5 or 1 hour per step may be selected, and either 3 levels or 4 levels timer may be selected. Please see TIMER section for details. HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 6 2000.12.31 M Y KE D E E D O SPEED KEY ORD SLP KE Y OFF Y KE SO1=L SO2=Z EY 1K SW SW E D E RSL M O D O 5. SW1 and SW2 KEYS SW1 and SW2 keys control the output status of SO1 and SO2 outputs which in turn control the head swing of fan. Depending on the 2SW mask option, SO2 is controlled by either SW1 or SW2 key. If 2SW option is selected each pressing of SW1 key toggles SO1 ON(L) and OFF(Z) and each pressing of SW2 key toggles SO1 ON(L) and OFF(Z). If 2SW option is not selected, pressing SW1 key cycles SO1 and SO2 output as shown in the diagram and SW2 key has no effect. 2SW option is described later. RTM M 4. MODE KEY MODE key is used to bring SC2128A around ORD (ordinary wind) mode, RTM(rhythm wind ) mode, SLP (sleep wind) mode and RSL(rhythm sleep wind ) mode. In ORD mode, the wind speed is set by SPEED key and does not change as time passes. In RTM mode the wind speed cycles through three rhythm wind, patterns as set by the SPEED key. In SLP and RSL mode, however, the fan automatically steps down one level (strong to middle, middle to low) every 30 minutes and keeps in low wind until off-timer times out. Four modes of operation are described in details later. KE Y SC2128A M O Silan Semiconductors 1K EY Fan already ON SO1=Z SO2=Z SW 1 SO1=Z SO2=L Z=high impedence L=low voltage KE Y SO1=L SO2=L 1 SW Y KE 6. LIGHT KEY LIGHT key toggles LIT output on(L) and off(Z). LIT output can only be controlled with LIGHT key (from both panel and remote control) and SLEEP key (if available) on remote control handset. OFF key does NOT affect LIT output. LIT output is NOT affected by OFF key as well as off-timer times out. 7. OFF/MEMS KEY OFF/MEMS key functions differently depending on whether the fan is ON or OFF. It functions as OFF key when the fan is ON, and is used to bring SC2128A from any on state into off state. LIT output is NOT affected by OFF key. When fan is OFF, it functions as MEMS (memory start) and is used to turn on the fan and set to the memory mode, provided memory mode is enabled. Memory mode is explained later in the MEMORY MODE section. 8. INDICATOR LEDS Up to twelve(12) indicator LEDs may be constructed on the control panel of fan built with SC2128A. Six(6) LEDs are constructed as 3x2 LED matrix formed by COM and LED1, LED2, LED3. The other six(6)LEDs are built in series with TRIAC outputs. The diagrams show how the LED matrix is constructed. HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 7 2000.12.31 Silan Semiconductors SC2128A low VDD LO middle Rhythm MI COM strong ST Tb0 LED3 Tb1 Tb2 Tb3 Sleep Swing 1 SO1 Swing 2 LED2 SO2 light LED1 LIT VSS -5V SC2128A SC2128A * Four LEDs (Tb0, Tb1, Tb2, Tb3) are used to indicate the off-timer period. Depending on the base timer step option, timer step may be 0.5 hour or 1 hour as indicated in the diagram. If SC2128A is selected with 4 hour timer option Tb0=0.5 hour b1=1 hour b2=2 hour b3=4 hour If SC2128A is selected with 8 hour timer option Tb0=1 hour b1=2 hour b2=4 hour b3=8 hour The time schedule is the sum of all ON LEDs. For example, if SC2128A is programmed with 0.5/1/2/4 hour accumulated timer option, and is Tb0 is ON, Tb1 is OFF, Tb2 is OFF, Tb3 is ON, then the schedule period is 4.5 hours (0.5 hr + 4 hr). * Rhythm LED and Sleep LED indicate SC2128A operation modes. Operation mode Rhythm LED Sleep LED ORD (ordinary wind) OFF OFF RTM (rhythm wind) ON OFF SLP (sleep wind) OFF ON RSL (rhythm sleep wind) ON ON * Three LEDs – Low, Middle and Strong – are used to indicate the respective output status of LO, MI, ST output. LED being ON indicates output active (L). LED being OFF indicates output inactive (Z). Only one output among LO, MI and HI may be active at a specific time. * Swing1 LED, Swing2 LED and Light LED indicated respective output status of SO1, SO2, and LIT. HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 8 2000.12.31 Silan Semiconductors SC2128A 9. TIMER The external timer of SC2128A may be bonding optioned into : 0.5, 1, 2, 4 hours non-accumulated : 1, 2, 4, 8 hours non-accumulated : 0.5, 1, 2, 4 hours accumulated : 1, 2, 4, 8 hours accumulated : 1, 2, 4 hours non-accumulated : 1, 2, 4 hours accumulated six (6) configurations as shown. Each pressing of TIMER key will step the internal timer one step up. The actual sequence depends on the TIMER option selected. The following diagrams show the timer sequence for each TIMER option. TIMER automatically counts down as time passes by. The count down sequence reverses the key sequence and is also shown in the following diagrams. TIMER 0.5hr TIMER 4+ 2+ 1 0.5hr 0.5hr 0.5hr 0.5hr TIMER 4+ 2+ 0.5 TIMER 0.5hr TIMER 0.5hr 0.5hr TIMER 4+ 1+ 0.5 4+ 2 TIMER TIMER 2+ 1+ 0.5 2+ 1 4 0.5hr TIMER 4+ 1 4+ 0.5 TIMER TIM ER 1hr 8+ 4+ 2+ 1 TIMER 2+ 1 1hr 1hr TIMER 1hr TIMER TIMER 8+ 4+ 2 8+ 4+ 1 1hr TIMER 4+ 1 4 TIMER TIMER 8+ 4 1hr TIMER 1hr 8+ 2+ 1 1hr TIMER 4+ 2+ 1 4+ 2 1hr 1hr 1hr 1hr TIMER TIMER 8+ 2 1hr 4 8+ 1 8 TIME R 1hr TIMER 2 1 ER 2 (5) 1hr TIMER TIM 1hr 0.5hr 0.5hr (3) None TIMER 1 None 1hr TIME R TIMER TIMER 2+ 0.5 2 0.5hr 4+ 2+ 1+ 0.5 TIM ER TIMER (6) TIME R 0.5hr 0.5hr TIMER 1+ 0.5 1 4+ 1 1hr 2hr TIMER TIMER 4+ 2 1hr 0.5hr (2) 0.5 2hr ER TIM (1) 4+ 2+ 1 ER 4 1hr 1hr TIMER TIM TIMER 2+ 1 1hr 1hr 2 4hr TIMER 2 TIME R 4 2hr TIMER None TIMER TIMER 1 None TIME R 2 TIMER 1 1hr 1hr TIME R TIMER 4 TIMER 0.5 None 1 0.5hr 0.5hr ER TIM TIMER TIMER 0.5 0.5h r TIMER None 1hr (4) 10. RHYTHM WIND SC2128A features rhythm wind mode. It can be set into rhythm wind mode by pressing MODE key. Furthermore, there are three levels – strong, middle and low rhythm wind. Pressing SPEED key cycles SC2128A around the three levels, from low to middle, middle to strong, then strong to low. Initial rhythm wind level on entering RHYTHM wind mode is the same as the ordinary wind level while leaving ORDINARY wind mode and entering RHYTHM wind mode. The right diagram depicts the strong, middle and low rhythm wind patterns. ST MI LO t=0 Strong rhythm wind pattern seconds t=90 t=0 Middle rhythm wind pattern seconds t=90 t=0 Low rhythm wind pattern seconds t=90 ST MI LO ST MI LO HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 9 2000.12.31 Silan Semiconductors SC2128A 11. SLEEP WIND MODE In sleep wind mode, the wind speed steps down automatically one level every 30 minutes, until it reaches low wind level. If no off-timer is set, SC2128A keeps in low wind level. Otherwise, it restores off state when off-timer times out. To enter sleep wind mode, turn on the fan by SPEED key first. Adjust to desired LO, MI, ST wind speed. Press MODE key twice to bring SC2128A to LOW, MIDDLE or STRONG sleep wind mode as the LO, MI, ST wind speed set before entering sleep wind mode. Press MODE key in sleep wind mode forces SC2128A to leave sleep wind mode and enter rhythm sleep wind mode. ST MI LO t=0 ST hours t=0.5hr t=1.0hr timer timeout Strong sleep mode wind pattern MI LO t=0 hours t=0.5hr t=1.0hr timer timeout Middle sleep mode wind pattern ST MI LO t=0 hours t=0.5hr t=1.0hr timer timeout Low sleep mode wind pattern 12. RHYTHM SLEEP WIND MODE Pressing MODE key in sleep wind mode brings SC2128A into rhythm sleep wind. In rhythm sleep wind mode, SC2128A outputs LOW, MIDDLE or STRONG rhythm wind pattern and automatically steps down one level every 30 minutes until it reaches low rhythm wind level. If no off-timer is set, SC2128A keeps in low rhythm wind output. Otherwise it restores off state when the off-timer times out. Strong rhythm wind Middle rhythm wind Low rhythm wind hours t=0 t=0.5hr t=1.0hr timer timeout Strong rhythm sleep mode wind pattern Strong rhythm wind Middle rhythm wind Low rhythm wind hours t=0 t=0.5hr t=1.0hr timer timeout Middle rhythm sleep mode wind pattern Strong rhythm wind Middle rhythm wind Low rhythm wind hours t=0 t=0.5hr t=1.0hr timer timeout Low rhythm sleep mode wind pattern 13. MEMORY MODE SC2128A features on-chip operation memory, in which operation state may be stored. OFF/MEMS key also functions as a special MEMS(memory start) key. If this key is pressed when SC2128A is in off state, SC2128A is activated into the operation mode stored in the operation memory. After power on, the operation memory is initialized as follows: middle speed, ordinary wind, none off-timer setting, SO1 and SO2 swing head outputs both off, LIT output off. Operation memory memorizes the following: (1) SPEED low, middle or strong, (2) MODE ordinary, rhythm, sleep or rhythm sleep. (3) OFF-TIMER: off-timer setting, (4) SWING HEAD SO1 and SO2 output state, (5) LIGHT LIT output status. If the fan is turned on by SPEED key, subsequent adjustments to the fan operation either from pannel key or from remote control handset do not affect the operation memory. If, however, the fan is turned on by MEMS, the subsequent adjustments to speed, mode, off-timer, SO1, SO2 and LIT output will update the operation memory to HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 10 2000.12.31 Silan Semiconductors SC2128A the final adjustments, regardless the adjustments are made from panel key or from remote control handset. One exception is the SLEEP key available on the remote control handset. SLEEP key start or adjusts the fan to the default sleep settings. Regardless the fan is started by SPEED or by MEMS, SLEEP key does not affect the operation memory. 14. BUZZER OUTPUT All valid key pressed except OFF/MEMS initiates a 150ms duration 4kHz 50% duty cycle pulse train at OFF/MEMS/BUZZ pin. OFF/MEMS key function as OFF key if pressed when fan is VDD in any on state. In this case, it does NOT initiate an output on BUZZ. OFF/MEMS key functions as MEMORY-START key if pressed when fan is in off state. In this case, it DOES initiate a SC2128A 150ms duration 4kHz 50% duty cycle pulse train on BUZZ. Note OFF/MEMS/ BUZZ OFF/MEMS key that when OFF/ MEMS/BUZZ outputs the pulse train, key input VSS is suppressed. That is, pressing OFF/MEMS key when the -5V buzzer is buzzing is NOT recognized by SC2128A. The diagram right shows the buzzer connection. 15. REMOTE CONTROL DECODER SC2128A is designed to be used together with SC2268 infrared ray remote control encoder. Such combination allows up to 8 remote control keys – SPEED, MODE, TIMER, LIGHT, SLEEP, SW1, SW2, OFF/MEMS – to be built on the remote control handset. 4 bits customer code, b3 ~ b6, is encoded by SC2268 and decoded by SC2128A in order to avoid remote control contention between devices. With SC2268, b3 is determined by bonding option; b4, b5 and b6 are determined by connecting respective c4, c5, c6 pin to VDD or VSS. With SC2128A, b3 and b6 can be mask programmed upon customer request and with NRE. The remote control signal coding scheme is fully Code bit: compatible with SC2268. Some description follows. "0" bit: Please refer to specification of SC2268 for details. When SC2128A receives a remote control signal at "1" bit: 0.625ms its REMOTE pin, it decodes the received waveform 1.875ms 2.5ms into consecutive “0” bits and “1” bits. It first compares the received start word against its customer code. If and only if the start word matches Start/Code word: the customer code, it then compares for two b0 b1 b2 b3 b4 b5 b6 b7 consecutive and matched code words. It then actuates the command according to the code words Code frame start word 1st code word 2nd code word table shown later. HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 11 2000.12.31 Silan Semiconductors SC2128A 16. CUSTOMER CODE The default customer code of SC2128A is internally mask programmed to b0 ~ b7 = 00110011. Code bit b3 ~ b6 may be mask programmed to any value according to customer specification under terms and conditions agreed by SILAN. Suitable NRE is involved with customizing default customer code. Please refer to the following table. Mask Option Start word Default Customer Code b0 b1 b2 b3 b4 b5 b6 b7 0 0 1 1 0 0 1 1 0 0 1 1 0 0 0 1 0 0 1 1 0 1 1 1 0 0 1 1 0 1 0 1 0 0 1 1 1 0 1 1 0 0 1 1 1 0 0 1 0 0 1 1 1 1 1 1 Mask Programmable 0 0 1 1 1 1 0 1 Customer Code 0 0 1 0 0 0 1 1 0 0 1 0 0 0 0 1 0 0 1 0 0 1 1 1 0 0 1 0 0 1 0 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0 1 0 1 1 1 1 0 0 1 0 1 1 0 1 17. REMOTE CONTROL KEYS Up to eight keys may be built on the remote control handset. Except SLEEP key, all keys functions the same as their panel counterparts. SLEEP key is not available on fan panel, and is only available on remote control handset. Pressing SLEEP key brings SC2128A to the output states as follows: SPEED Middle wind MODE RSL wind (may be mask programmed to SLP Wind with NRE) TIMER 4 hours or 8 hours SWING SO1 ON, SO2 OFF LIGHT LIT ON The remote transmission code words are defined in the following table. SC2268 Code word Equivalent Key Corresponding b0 b1 b2 b3 b4 b5 b6 b7 Keys SPEED 0 0 1 1 1 0 1 0 I1 MODE 0 1 0 1 1 0 0 0 I2 TIMER 0 1 1 0 0 0 1 0 I3 LIGHT 1 0 0 1 1 1 0 0 I4 SLEEP 1 0 1 0 0 1 1 0 I5 SW2 1 0 1 1 0 0 0 1 I6 SW1 1 1 0 0 0 1 0 1 I7 OFF/MEMS 1 1 0 1 0 0 1 0 I8 HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 12 2000.12.31 Silan Semiconductors SC2128A 18. VARIOUS OPTIONS SC2128A accommodates many option possibilities. The options are summarized below: * Package Option: Either 16, 18, 20, 22, or 24 pin package. * Bonding option: ACC: Accumulated or non-accumulated timer option. T0.5: Timer scale, 0.5/1/2/4 hour timer or 1/2/4/8 timer option. 3LT: Timer level option, either 4 levels or 3 levels. NM: Disable memory mode. * Metal Option: b3 ~ b6: Replaces default customer codes NMS: Disable middle wind start-up function 2SW: Dependent/Independent swing head control option. RSL: SLEEP key start-up mode option – select RSL or SLP mode for SLEEP key start-up. HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 13 2000.12.31 Silan Semiconductors SC2128A APPLICATION CIRCUIT AC SC2128A Swing2 220Ω SW2 SO2 SW2 Low REMOTE LO VSS MI OSCI ST 220Ω Middle 220Ω Strong 220Ω 47pf IR MODULE 32.768kHz -5V OSCO LED1 VDD LED2 Sleep 47pf 9.1kΩ Tb2 OFF/MEMS/ LED3 BUZZ OFF/MEMS SPEED Rhythm Tb0 Tb3 COM Tb1 TIMER SPEED MODE -5V TIMER MODE Swing1 220Ω SW1 SO1 SW1 Light LIGHT 220Ω LIT LIGHT Swing Head 1: Controlled by SW1 Swing Head 2: Controlled by SW2 200kΩ IN4004 22Ω/2w 2SA1015 AC VAR 2.5µf/250V 6.8V/1w AC FUSE -5V 1kΩ 470µf 16V 10µf 16V 0.1µf Supply Circuit HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 14 2000.12.31 Silan Semiconductors SC2128A SC2268 IR TRANSMITTER APPLICATION CIRCUIT +3V SPEED 1 I1 Vcc 16 MODE 2 I2 OSC1 15 TIMER 3 I3 OSC2 14 LIGHT 4 I4 Tx OUT 13 SLEEP 5 I5 C4 12 SW2 6 I6 C5 11 SW1 7 I7 C6 10 OFF/MEMS 8 I8 Vss 9 220pf 455kHz 10Ω 220pf IR LED A1015 C1815 1kΩ SC2268 Note: SC2268 is recommended to be used with SC2128A. For this circuit, the “Start Word” is “00110011” PACKAGE OUTLINE DIP-16-300-2.54 UNIT:mm 7.62 6.40 0.25 2.54 1.50 15 degree 3.30 5.08 3.51 19.4 0.46 HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 15 2000.12.31