SL4502B Strobed Hex Inverter/Buffer High-Voltage Silicon-Gate CMOS The SL4502B consists of six inverter/buffers with 3-state outputs. A logic “1” on the OUTPUT ENABLE input produces a high impedance state in all six outputs. This feature permits common busing of the outputs, thus simplifying system design. A logic “1” on the DIRECTION input switches all six outputs to logic “0” if the OUTPUT ENABLE input is a logic “0”. • Operating Voltage Range: 3.0 to 18 V • Maximum input current of 1 µA at 18 V over full packagetemperature range; 100 nA at 18 V and 25°C • Noise margin (over full package temperature range): 1.0 V min @ 5.0 V supply 2.0 V min @ 10.0 V supply 2.5 V min @ 15.0 V supply ORDERING INFORMATION SL4502BN Plastic SL4502BD SOIC TA = -55° to 125° C for all packages PIN ASSIGNMENT LOGIC DIAGRAM FUNCTION TABLE Inputs PIN 16=VCC PIN 8= GND SLS System Logic Semiconductor Output Output Enable Direction A Y L L L H L L H L L H X L H X X Z Z = high impedance X = don’t care SL4502B MAXIMUM RATINGS * Symbol Parameter Value Unit -0.5 to +20 V VCC DC Supply Vo ltage (Referenced to GND) VIN DC Input Voltage (Referenced to GND) -0.5 to VCC +0.5 V DC Output Voltage (Referenced to GND) -0.5 to VCC +0.5 V VOUT IIN DC Input Current, per Pin ±10 mA PD Power Dissipation in Still Air, Plastic DIP+ SOIC Package+ 750 500 mW PD Power Dissipation per Output Transistor 100 mW -65 to +150 °C 260 °C Tstg TL Storage Temperature Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP or SOIC Package) * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. +Derating - Plastic DIP: - 10 mW/°C from 65° to 125°C SOIC Package: : - 7 mW/°C from 65° to 125°C RECOMMENDED OPERATING CONDITIONS Symbol VCC VIN, VOUT TA Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage, Output Voltage (Referenced to GND) Operating Temperature, All Package Types Min Max Unit 3.0 18 V 0 VCC V -55 +125 °C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND≤(VIN or VOUT)≤VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. SLS System Logic Semiconductor SL4502B DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) VCC Symbol Parameter Test Conditions Guaranteed Limit V ≥-55°C 25°C ≤125 °C Unit VIH Minimum High-Level Input Voltage VOUT=0.5 V VOUT=1 V VOUT=1.5 5.0 10 15 3.5 7 11 3.5 7 11 3.5 7 11 V VIL Maximum Low -Level Input Voltage VOUT= VCC - 0.5V VOUT= VCC - 1.0 V VOUT= VCC - 1.5V 5.0 10 15 1.5 3 4 1.5 3 4 1.5 3 4 V VOH Minimum High-Level Output Voltage VIN=GND 5.0 10 15 4.95 9.95 14.95 4.95 9.95 14.95 4.95 9.95 14.95 V VOL Maximum Low-Level Output Voltage VIN= VCC 5.0 10 15 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 V IIN Maximum Input Leakage Current VIN= GND or VCC 18 ±0.1 ±0.1 ±1.0 µA ICC Maximum Quiescent Supply Current (per Package) VIN= GND or VCC 5.0 10 15 20 1 2 4 20 1 2 4 20 30 60 120 600 µA IOL Minimum Output Low (Sink) Current VIN= GND or VCC UOL=0.4 V UOL=0.5 V UOL=1.5 V 5.0 10 15 3.84 9.6 25.2 3.06 7.8 20.4 2.16 5.4 14.4 Minimum Output High VIN= GND or VCC (Source) Current UOH=2.5 V UOH=4.6 V UOH=9.5 V UOH=13.5 V 5.0 5.0 10 15 -2 -0.64 -1.6 -4.2 -1.6 -0.51 -1.3 -3.4 -1.15 -0.36 -0.9 -2.4 18 ±0.4 ±0.4 ±12 IOH IOZ SLS Maximum Tree-State Leakage Current System Logic Semiconductor Output in High-Impedance State VIN= GND or VCC VOUT= GND or VCC mA mA µA SL4502B AC ELECTRICAL CHARACTERISTICS (CL=50pF, RL=200kΩ unless otherwise specified, Input tr=t f=20 ns) VCC Symbol Parameter Guaranteed Limit V ≥-55°C 25°C ≤125°C Unit tPHL Maximum Propagation Delay, Input A or Direction to Output Y (Figure 1) 5.0 10 15 270 120 80 270 120 80 540 240 160 ns tPLH Maximum Propagation Delay, Input A or Direction to Output Y (Figure 1) 5.0 10 15 380 180 130 380 180 130 760 360 260 ns tPHZ Maximum Propagation Delay, Output Enable to Output Y (Figure 2) RL = 1 kΩ 5.0 10 15 120 80 60 120 80 60 240 160 120 ns tPZH Maximum Propagation Delay, Output Enable to Output Y (Figure 2) RL = 1 kΩ 5.0 10 15 220 100 80 220 100 80 440 200 160 ns tPLZ Maximum Propagation Delay, Output Enable to Output Y (Figure 2) RL = 1 kΩ 5.0 10 15 250 130 110 250 130 110 500 260 220 ns tPZL Maximum Propagation Delay, Output Enable to Output Y (Figure 2) RL = 1 kΩ 5.0 10 15 250 110 80 250 110 80 500 220 160 ns tTLH Maximum Output Transition Time, Any Output (Figure 1) 5.0 10 15 200 100 80 200 100 80 400 200 160 ns tTHL Maximum Output Transition Time, Any Output (Figure 1) 5.0 10 15 120 60 40 120 60 40 240 120 80 ns CIN Maximum Input Capacitance - 7.5 pF Maximum Tree-State Output Capacitance (Output in High-Impedance State) - 15 pF COUT SLS System Logic Semiconductor SL4502B Figure 1. Switching Waveforms Figure 2. Switching Waveforms EXPANDED LOGIC DIAGRAM (1/6 of the Device) SLS System Logic Semiconductor