tm TE CH T81L0003A MCU Reduced I/O 8-bit MCU FEATURES ! ! ! ! ! ! ! ! ! ! ! ! ! ! Compatible with MCS-51 Products 128 x8 bit RAM Embedded 8k X 8 bit data OTP ROM 13 bi-direction I/O Lines. System clock: Typ. 12MHz @ 2.5 ~ 5.5V. 2 External Interrupt Input Programmable Serial UART Channel. Watch Dog Timer One 16-bit Timer/Counter (T0) & Two 16-bit Timer (T1, T2) On-chip selectable crystal driving PAD or RC oscillator. Low Power and wake-able power down mode One Buzzer Driving Pad.P1.0 (driving capability up to 40mA). SOP18/DIP18 Package. Typical 3.3V Operating Voltage. Description The T81L0003A is a low voltage and low cost and reduced I/O 8-bit high performance 8051-like MCU. The T81L0003A provides 13 bi-direction I/Os for end user programming with other device and 3 timers (but only one counter) for more applications and low cost. Part Number Example Part No. T81L0003A-AK T81L0003A-AD T81L0003A-BK T81L0003A-BD Pkg. DIP 18 pin SOP 18 pin DIP 18 pin SOP 18 pin Description RC oscillation RC oscillation Crystal oscillation Crystal oscillation TM Technology, Inc. reserves the right to change products or specifications without notice. P. 1 Publication Date: SEP. 2004 Revision: C tm TE CH T81L0003A Block Diagram P1.0 -P1.7 Port 1 Drivers RAM Addr. Register B Register Port 1 Latch RAM OTP ROM Stack Pointer ACC TMP2 Program Address Register TMP1 WDT Buffer ALU PC Incrementer PSW Interrupt, Serial port, and Timer Block Timing & Instruction Control Register Program Counter DPTR RST Port 3 Latch OSC Port 3 Drivers P3.0 -P3.4 TM Technology, Inc. reserves the right to change products or specifications without notice. P. 2 Publication Date: SEP. 2004 Revision: C tm TE CH T81L0003A Pin Configuration 1 2 3 4 5 6 7 8 9 P1.7 VDD RST P3.1/TXD OSCR STOP VSS P3.0/RXD P3.3/INT1 P1.6 P1.5 P1.4 P1.3 P1.2 P1.1 P1.0/BUZ P3.2/INT0 P3.4/T0 18 17 16 15 14 13 12 11 10 T81L0003A-AK, AD 1 2 3 4 5 6 7 8 9 P1.7 P1.6 VDD P1.5 RST P1.4 P3.1/TXD P1.3 XOUT P1.2 XIN P1.1 VSS P1.0/BUZ P3.0/RXD P3.2/INT0 P3.3/INT1 P3.4/T0 18 17 16 15 14 13 12 11 10 T81L0003A-BK,BD TM Technology, Inc. reserves the right to change products or specifications without notice. P. 3 Publication Date: SEP. 2004 Revision: C tm TE CH T81L0003A Pin Assignment Pin No. .Assignment I/O Options Description 1 P1.7 I/O 2 VDD -- 3 RST I 4 P3.1/TXD I/O 5(BK, BD) XOUT O Crystal output terminal 5(AK, AD) OSCR I RC Input 6(BK, BD) XIN I Crystal input terminal 6(AK, AD) STOP O RC Stop 7 VSS -- 8 P3.0/RXD I/O General Purpose I/O and serial receive 9 P3.3/INT1 I/O General Purpose I/O and interrupt1 input 10 P3.4/T0 I/O General Purpose I/O and Timer0 11 P3.2/INT0 I/O General Purpose I/O and interrupt0 input 12 P1.0/BUZ I/O General Purpose I/O and Buzzer driving pad 13 P1.1 I/O General Purpose I/O 14 P1.2 I/O General Purpose I/O 15 P1.3 I/O General Purpose I/O 16 P1.4 I/O General Purpose I/O 17 P1.5 I/O General Purpose I/O 18 P1.6 I/O General Purpose I/O General Purpose I/O 3.3V Power Supply Reset signal input General Purpose I/O and serial transmit GND TM Technology, Inc. reserves the right to change products or specifications without notice. Ground P. 4 Publication Date: SEP. 2004 Revision: C tm TE CH T81L0003A Pin Description VDD 3.3V Supply voltage. GND Ground. Port 1 Port 1 is an 8-bit bi-directional I/O port with internal pull-ups. The Port 1 output buffers can sink/source four TTL inputs. When port 1 pins are written as 1’s, these pins are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 1 pins that are externally being pulled low will source current (I IL ) because of the internal pull-ups. Port 1 also receives the low-order address bytes during OTP programming and verification. P1.0 serves as functions of Buzz used driving buzzer, because this pin design for more driving capability than other general I/O. Port 3 Port 3 is an 8-bit bi-directional I/O port with internal pull-ups. The Port 3 output buffers can sink/source four TTL inputs. When port 0 pins are written as 1’s, these pins are pulled high by the internal pullups and can be used as inputs. As inputs, Port 3 pins that are externally being pulled low will source current (I IL ) because of the pullups. Port 3 also serves the functions of various special features of the T81L0001A as listed below: Alternate Function: P3.0: RXD P3.1: TXD P3.2: INT0 P3.3: INT1 P3.4: T0 RST Reset input and active high. When high on this pin should be lasting for two machine cycles while the oscillator is running resets the device. XIN Input to the inverting oscillator amplifier and input to the internal clock operating circuit in BK,BD parts. XOUT Output from the inverting oscillator amplifier in BK,BD part. TM Technology, Inc. reserves the right to change products or specifications without notice. P. 5 Publication Date: SEP. 2004 Revision: C tm TE CH T81L0003A OSCR Input to the RC oscillator amplifier and input to the internal clock operating circuit in AK, AD parts. STOP RC oscillation stop pin in AK, AD parts which should keep floating while using external clock in or tie to low level using RC oscillation. Internal Register(Compatible with standard 8051 instruction and setting) Special Function Register F8H F0H B E8H E0H ACC D8H D0H PSW C8H T2CON T2MOD RCAP2L RCAP2H TL2 TH2 TH0 TH1 C0H B8H IP B0H P3 A8H IE A0H P2* 98H SCON 90H P1 88H TCON TMOD TLO TL1 80H P0* SP DPL DPH SBUF WDTREL PCON *Note: P0:Internal still keeping, but for pad dominate, no external pin assignment P2:Internal still keeping, but for pad dominate, no external pin assignment Accumulator ACC is the Accumulator register. The mnemonics for Accumulator-Specific instructions, however, refer to the Accumulator simply as A. B Register The B register is used during multiply and divide operations. For other instructions it can be treated as another scratch pad register. TM Technology, Inc. reserves the right to change products or specifications without notice. P. 6 Publication Date: SEP. 2004 Revision: C tm TE CH T81L0003A Program Status Word The PSW register contains program status information as detailed in MSB CY LSB AC F0 RS1 RS0 OV -- P BIT SYMBOL FUNCTION PSW.7 CY Carry flag. PSW.6 AC Auxilliary Carry flag. (For BCD operations.) PSW.5 F0 Flag 0. (Available to the user for general purposes.) PSW.4 RS1 Register bank select control bit 1. Set/cleared by software to determine working register bank. (See Note.) PSW.3 RS0 Register bank select control bit 0. Set/cleared by software to determine working register bank. (See Note.) PSW.2 OV Overflow flag. PSW.1 — User-definable flag. PSW.0 P Parity flag. Set/cleared by hardware each instruction cycle to indicate an odd/even number of “one” bits in the Accumulator, i.e., even parity. NOTE: The contents of (RS1, RS0) enable the working register banks as follows: (0,0)— Bank 0 (00H–07H) (0,1)— Bank 1 (08H–0fH) (1,0)— Bank 2 (10H–17H) (1,1)— Bank 3 (18H–1fH) Stack Pointer The Stack Pointer register is 8 bits wide. It is incremented before data is stored during PUSH and CALL executions. While the stack may reside anywhere in on-chip RAM, the Stack Pointer is initialized to 07H after a reset. This causes the stack to begin at locations 08H. Data Pointer (DPTR) The Data Pointer (DPTR) consists of a high byte (DPH) and a low byte (DPL). Its intended function is to hold a 16-bit address. It may be manipulated as a 16-bit register or as two independent 8-bit registers. Ports 1.0-1.7 & 3.0-3.4 All Ports are the SFR latches, respectively. Writing a one to a bit of a port SFR (P1 or P3) causes the corresponding port output pin to switch high. Writing a zero causes the port output pin to switch low. When used as an input, the external state of a port pin will be held in the port SFR (i.e., if the external state of a pin is low, the corresponding port SFR bit will contain a ‘0’; if it is high, the bit will contain a ‘1’). TM Technology, Inc. reserves the right to change products or specifications without notice. P. 7 Publication Date: SEP. 2004 Revision: C tm TE CH T81L0003A Serial Data Buffer The Serial Buffer is actually two separate registers, a transmit buffer and a receive buffer. When data is moved to SBUF, it goes to the transmit buffer and is held for serial transmission. (Moving a byte to SBUF is what initiates the transmission.) When data is moved from SBUF, it comes from the receive buffer. Timer Registers Register pairs (TH0, TL0) is the 16-bit Counting registers for Timer/Counters 0, while (TH1, TL1) and (TH2, TL2) are the 16-bit Counting registers for Timer1 and Timer2, respectively. . Control Register Special Function Registers IP, IE, TMOD, TCON, SCON, and PCON contain control and status bits for the interrupt system, the Timer/Counters, and the serial port. They are described in later sections. Power Down Mode The power down mode can be active by setting the PD bit (on PCON register) to 1 and the program status will keep on the state before power down set. The MCU can be woken up by interrupt (I0 or I1) if the one is enable. After wake up, need to clear PD bit to 0 on first instruction. PCON (address: 87H) MSB SMOD LSB - - - GF1 GF0 PD - Standard Serial Interface The serial port is full duplex, meaning it can transmit and receive simultaneously. It is also receive-buffered, meaning it can commence reception of a second byte before a previously received byte has been read from the register. (However, if the first byte still hasn’t been read by the time reception of the second byte is complete, one of the bytes will be lost.) The serial port receive and transmit registers are both accessed at Special Function Register SBUF. Writing to SBUF loads the transmit register, and reading SBUF accesses a physically separate receive register. The serial port can operate in 4 modes: Mode 0: Serial data enters and exits through RxD. TxD outputs the shift clock. 8 bits are transmitted/received (LSB first). The baud rate is fixed at 1/12 the oscillator frequency. Mode 1: 10 bits are transmitted (through TxD) or received (through RxD): a start bit (0), 8 data bits (LSB first), and a stop bit (1). On receive, the stop bit goes into RB8 in Special Function Register SCON. The baud rate is variable. Mode 2: 11 bits are transmitted (through TxD) or received (through RxD): start bit (0), 8 data bits (LSB first), a programmable 9th data bit, and a stop bit (1). On Transmit, the 9th data bit (TB8 in SCON) can be assigned the value of 0 or 1. Or, for example, the parity bit (P, in the PSW) could be moved into TB8. On receive, the 9th data bit goes into RB8 in TM Technology, Inc. reserves the right to change products or specifications without notice. P. 8 Publication Date: SEP. 2004 Revision: C tm TE CH T81L0003A Special Function Register SCON, while the stop bit is ignored. The baud rate is programmable to either 1/32 or 1/64 the oscillator frequency. Mode 3: 11 bits are transmitted (through TxD) or received (through RxD): a start bit (0), 8 data bits (LSB first), a programmable 9th data bit, and a stop bit (1). In fact, Mode 3 is the same as Mode 2 in all respects except baud rate. The baud rate in Mode 3 is variable. In all four modes, transmission is initiated by any instruction that uses SBUF as a destination register. Reception is initiated in Mode 0 by the condition RI = ‘0’ and REN = ‘1’. Reception is initiated in the other modes by the incoming start bit if REN = ‘1’. Multiprocessor Communications Modes 2 and 3 have a special provision for multiprocessor communications. In these modes, 9 data bits are received. th The 9 one goes into RB8. Then comes a stop bit. The port can be programmed such that when the stop bit is received, the serial port interrupt will be activated only if RB8 = ‘1’. This feature is enabled by setting bit SM2 in SCON. A way to use this feature in multiprocessor systems is as follows: When the master processor wants to transmit a block of data to one of several slaves, it first sends out an address byte which identifies the target slave. An address byte differs from a data byte in that the 9th bit is ‘1’ in an address byte and ‘0’ in a data byte. With SM2 = ‘1’, no slave will be interrupted by a data byte. An address byte, however, will interrupt all slaves, so that each slave can examine the received byte and see if it is being addressed. The addressed slave will clear its SM2 bit and prepare to receive the data bytes that will be coming. The slaves that weren’t being addressed leave their SM2s set and go on about their business, ignoring the coming data bytes. SM2 has no effect in Mode 0, in Mode 1 can be used to check the validity of the stop bit. In Mode 1 reception, if SM2 = ‘1’, the receive interrupt will not active unless a valid stop bit is received. Serial Port Control Register The serial port control and status register is the Special Function Register SCON. This register contains not only the mode selection bits, but also the 9th data bit for transmit and receive (TB8 and RB8), and the serial port interrupt bits (TI and RI). Baud Rates The baud rate in Mode 0 is fixed: Mode 0 Baud Rate = Oscillator Frequency / 12. The baud rate in Mode 2 depends on the value of bit SMOD in Special Function Register PCON. If SMOD = ‘0’ (which is the value on reset), the baud rate is 1/64 the oscillator frequency. If SMOD = ‘1’, the baud rate is 1/32 the oscillator frequency. Mode 2 Baud Rate =2 SMOD/64* (Oscillator Frequency) In the 80C52, the baud rates in Modes 1 and 3 are determined by the Timer 1 overflow rate. SCON MSB SM0 LSB SM1 SM2 REN TM Technology, Inc. reserves the right to change products or specifications without notice. TB8 P. 9 RB8 TI RI Publication Date: SEP. 2004 Revision: C tm TE CH T81L0003A Where SM0, SM1 specify the serial port mode, as follows: SM0 SM1 Mode Description Baud Rate 0 0 0 shift register f OSC / 12 0 1 1 8-bit UART variable 1 0 2 9-bit UART UART f OSC /64 or f OSC /32 1 1 3 9-bit UART variable Using Timer 1 to Generate Baud Rates When Timer 1 is used as the baud rate generator, the baud rates in Modes 1 and 3 are determined by the Timer 1 overflow rate and the value of SMOD as follows: Mode 1, 3 Baud Rate =2 SMOD/32* (Timer 1 Overflow Rate) The Timer 1 interrupt should be disabled in this application. The Timer itself can be configured for either “timer” or “counter” operation, and in any of its 3 running modes. In the most typical applications, it is configured for “timer” operation, in the auto-reload mode (high nibble of TMOD = 0010B). In that case the baud rate is given by the formula: Mode 1, 3 Baud Rate =2 SMOD*(Oscillator Frequency)/ 32/12 / [256 _ (TH1)] One can achieve very low baud rates with Timer 1 by leaving the Timer 1 interrupt enabled, and configuring the Timer to run as a 16-bit timer (high nibble of TMOD = 0001B), and using the Timer 1 interrupt to do a 16-bit software reload. Using Timer 2 to Generate Baud Rates Timer2 is selected as the baudrate generator by setting TCLK and/or RCLK in T2CON register as followed. T2CON (address : C8h) MSB TF2 LSB EXF2 RCLK TCLK EXEN2 TR2 C/T2 CP/RL2 T2CON.7: TF2 Timer2 overflow flag set by timer2 overflow and must be cleared by software. TF2 will not be set when either RCLK=1 or TCLK=1. T2CON.6: EXF2 Timer 2 external flag set when either a capture or reload is caused by a negative transition on T2EX and EXEN2=1. when timer2 interrupt is enabled, EXF2=1 will cause the CPU to vector to the timer2 interrupt routine. EXF2 must be cleared by software. T2CON.5: RCLK Receive clock flag. When set, cause the serial port to use timer2 overflow pulses for its receive clock in mode 1 and 3. RCLK=0 causes timer1 overflow to be used for the receive clock T2CON.4: TCLK Transmit clock flag. When set, cause the serial port to use timer2 overflow pulses for its transmit clock in mode 1 and 3. TCLK=0 causes timer1 overflow to be used for the transmit clock T2CON.3: EXEN2 Timer2 external enable flag. When set, allows a capture or reload to occur as a result of a negative transition on T2EX if timer2 is not being used to clock the serial port. EXEN2=0 causes timer2 to ignore events at T2EX. T2CON.2: Start/stop control for timer2. A logic 1 starts the timer TM Technology, Inc. reserves the right to change products or specifications without notice. P. 10 Publication Date: SEP. 2004 Revision: C tm TE CH T81L0003A T2CON.1: Timer or counter select. (Timer 2) , 0 as internal timer T2CON.0: Capture/Reload flag. When set, captures will occur on negative transitions at T2EX if EXEN2=1. When cleared, auto reloads will occur either with timer2 overflow or negative transitions at T2EX when EXEN2=1. When either RCLK=1 or TCLK=1, this bit is ignored and the timer is forced to auto-reload on timer2 overflow. Note then the baudrates for transmit and receive can be simultaneously different. Setting RCLK and/or TCLK puts Timer2 into its baudrate generator mode. The baudrate generator mode is similar to the auto reload mode, in that a rollover is TH2 causes the Timer2 registers to be reload with the 16 bit value in registers RCAP2H and RCAP2L, which are preset by software given by the formula. Baudrate= (Timer2 overflow rate)/16 =(Oscillator Frequency) / (32*(65536-(RCAP2H,RCAP2L))) Serial Interface Timing Diagram S1.........S6 S1.........S6 S1.........S6 S1.........S6 S1.........S6 S1.........S6 S1.........S6 S1.........S6 S1.........S6 S1.........S6 A LE W rite to SB U F Shift RX D D0 D1 D2 D3 D4 D5 D6 D7 Transmit Send TX D W rite to SC O N ,C lear R I Receive RI R eceive Shift D0 D1 D2 D3 D4 D5 D6 D7 RX D TX D Serial Port M ode 0 TM Technology, Inc. reserves the right to change products or specifications without notice. P. 11 Publication Date: SEP. 2004 Revision: C tm TE CH T81L0003A TX clock W rite to SB U F Transm it Send D ata Shift TX D StartB it D0 D1 D2 D3 D4 D5 D6 D7 StartB it D0 D1 D2 D3 D4 D5 D6 D7 Stop B it TI RX D Stop B it Receive RX clock Shift RI Serial Port M ode 1 TX clock W rite to SB U F Transmit Send D ata Shift Stop B it TX D StartB it D0 D1 D2 D3 D4 D5 D6 D7 TB 8 StartB it D0 D1 D2 D3 D4 D5 D6 D7 TB 8 TI RX clock Shift Receive Stop B it RX D RI Serial Port M ode 2 TM Technology, Inc. reserves the right to change products or specifications without notice. P. 12 Publication Date: SEP. 2004 Revision: C tm TE CH T81L0003A TX clock W rite to SB U F Transmit Send D ata Shift Stop B it TX D Start B it D0 D1 D2 D3 D4 D5 D6 D7 TB 8 Start B it D0 D1 D2 D3 D4 D5 D6 D7 TB 8 TI RX clock Shift Receive Stop B it RXD RI Serial Port M ode 3 TM Technology, Inc. reserves the right to change products or specifications without notice. P. 13 Publication Date: SEP. 2004 Revision: C tm TE CH T81L0003A Watchdog Timer The watchdog timer is a 16-bit counter that is incremented once every 24 or 384 clock cycles. After an external reset the watchdog timer is disabled and all registers are set to zeros. ! Watchdog Timer structure The watchdog consists of 16-bit counter wdt, reload register wdtrel, prescalers by 2 and by 16 and control logic. Where wdtl=00h while start up. Figure Watchdog block diagram ! Start procedure There are one way to start the watchdog. A programmer can start the watchdog as refreshing procedure. Once the watchdog is started it cannot be stopped unless rst signal becomes active. When wdt registers enters the state 7FFCh, asynchronous wdts signal will become active. The signal wdts sets the bit 6 in ip0 register and requests reset state. The wdts is cleared either by rst signal or change of the state of the wdt timer. Procedure: load wdtrel value # set “wdt” # set “swdt” in 12 instruction cycles. TM Technology, Inc. reserves the right to change products or specifications without notice. P. 14 Publication Date: SEP. 2004 Revision: C tm TE CH T81L0003A ! Refreshing the watchdog timer The watchdog timer must be refreshed regularly to prevent reset request signal from becoming active. This requirement imposes obligation on the programmer to issue two followed instructions. The first instruction sets wdt and the second one swdt. The maximum allowed delay between settings of the wdt and swdt is 12 instruction cycles. While this period has expired and swdt has not been set, wdt is automatically reset, otherwise the watchdog timer is reloaded with the content of the wdtrel register and wdt is automatically reset. The procedure is as “Start procedure” before. ! Special Function Registers a) Interrupt Enable 0 register (ien0) The ien0 register (address : A8) MSB LSB eal wdt et2 es0 et1 ex1 et0 ex0 The ien0 bit functions Bit Symbol Function ien0.6 wdt Watchdog timer refresh flag. Set to initiate a refresh of the watchdog timer. Must be set directly before swdt is set to prevent an unintentional refresh of the watchdog timer. The wdt is reset by hardware 12 instruction cycles after it has been set. Note: other bits are not used to watchdog control b) Interrupt Enable 1 register (ien1) The ien1 register (Address : B8) MSB LSB - swdt pt2 ps pt1 px1 pt0 px0 The ien1 bit functions Bit Symbol Function Ien1.6 swdt Watchdog timer start refresh flag. Set to active/refresh the watchdog timer. When directly set after setting wdt, a watchdog timer refresh is performed. Bit swdt is reset by hardware 12 instruction cycles after it has been set. Pay attention that when write ien1.6, it write the swdt bit, when read ien1.6, we will read out the wdts bit. Ie. Watch dog timer status flag. Set by hardware when the watchdog timer was started. TM Technology, Inc. reserves the right to change products or specifications without notice. P. 15 Publication Date: SEP. 2004 Revision: C tm TE CH T81L0003A d) Watchdog Timer Reload register (wdtrel) The wdtrel register ( Address : 86 ) MSB LSB 7 6 5 4 3 2 1 0 The wdtrel bit functions Bit Symbol wdtrel.7 7 Function Prescaler select bit. When set, the watchdog is clocked through an additional divide-by-16 prescaler wdtrel.6 t0 6-0 wdtrel.0 Seven bit reload value for the high-byte of the watchdog timer. This value is loaded to the wdt when a refresh is triggered by a consecutive setting of bits wdt and swdt The wdtrel register can be loaded and read any time ! WDT Reset A high on reset pin or watchdog reset request for two clock cycles while the oscillator is running resets the device. Diagram b) Watchdog timer reset 7FFBH 7FFCH 0000H Figure Watchdog reset timing TM Technology, Inc. reserves the right to change products or specifications without notice. P. 16 Publication Date: SEP. 2004 Revision: C tm TE CH T81L0003A **Note : clk: external clock input Tclk: clock period wdt: watchdog timer registers wdts: watchdog timer status flag reset: external reset input rst: internally generated reset signal ! Reset Time Formula Reset time=(7FFCh-wdth.wdtl)*presc*48/ClockFrequency while presc=16 if wdtrel.7=1, presc=1 if wdtrel.7=0. For example if you use frequency clock=12MHz, wdtrel=10111111b which means wdtrel.7=1 and wdth=3Fh Then reset time= (7FFCh-3F00h)*48/12M=66544 us Instruction Set (Fully Compatible standard MCS-51 Instruction) AC Electrical Characteristics (Ta=0oC~70oC, VDD=3.3V, VSS=0V) Symbol Parameter Dclk Input CLK Duty cycle fclk Clock frequency Condition Counter input period Tdrh Device reset hold time Trst RESET pulse width Twdt Watchdog timer Typ Max Unit 45 50 55 % 37 MHz 12.6 MHz 2096000 us Crystal Type RC Type(R=47KOhm) Tcntin Min 11.4 Ta=25oC 12 9*fclk 2*fclk Clock frequency=12MHz TM Technology, Inc. reserves the right to change products or specifications without notice. P. 17 16128 Publication Date: SEP. 2004 Revision: C tm TE CH T81L0003A DC Electrical Characteristics Symbol Parameter VDD Core voltage VIH Hi-Level input voltage VIL Low-Level input voltage Test Condition Min. Typ. Max. Unit 2.5 3.3 5.5 V Vout >=VVOH(MIN.) 2.0 VDD+0.3 VDD+0.3 V Vout <=VVOL(MIN.) -0.3 0.3*VDD 0.3*VDD V Junction temperature -40oC ~ 85oC VDD =3.3V. VI=VIH VOH Hi-Level Output voltage VDD =3.3V. VI=VIH VDD =3.3V. VI=VIH VDD =3.3V. VI=VIL VOL1 Low-Level Output voltage (P1.0/Buz) VDD =3.3V. VI=VIL VDD =3.3V. VI=VIL VDD =3.3V. VI=VIL VOL2 Low-Level Output voltage (Else Pins) VDD =3.3V. VI=VIL VDD =3.3V. VI=VIL II Input current IPD Power down IOH=-7uA 2.9 IOH=-45uA 2.4 IOH=-70uA 1.9 V IOL=12mA 0.2 IOL=25mA 0.4 IOL=40mA 0.6 IOL=4mA 0.2 IOL=12mA 0.4 IOL=19mA 0.6 VDD =3.3. V TBD. uA VI=VDD or GND VDD =3.3V. TM Technology, Inc. reserves the right to change products or specifications without notice. 0.1 P. 18 1 uA Publication Date: SEP. 2004 Revision: C tm TE CH T81L0003A Package Dimension 0.020X45 H 9 1 E 10 18 18-LEAD SOP 0.050typ A 0.016typ X A1 L D 0.004max SYMBOLS MIN. MAX. A 0.093 0.104 A1 0.004 0.012 D 0.447 0.463 E 0.291 0.229 H 0.394 0.419 L 0.016 0.050 X 0 8 UNIT: INCH TM Technology, Inc. reserves the right to change products or specifications without notice. P. 19 Publication Date: SEP. 2004 Revision: C tm TE CH T81L0003A 18-LEAD DIP E +0.020 0.312 +- 0.012 0.350 +- 0.020 10 9 R40 0.290 +- 0.014 18 1 B +0.020 C +- 14 D +- 14 0.310 M ax 0.115 Min. 0.015 Min. A +- 10 0.100 Typ. 0.018 +0.012 Typ. 0.060 +0.015 Typ. A B C D E 0.900 0.075 0.065 0.055 0.090 UNIT: INCH TM Technology, Inc. reserves the right to change products or specifications without notice. P. 20 Publication Date: SEP. 2004 Revision: C