GP1601 THRU GP1607 16.0 AMPS. Glass Passivated Rectifiers Voltage Range 50 to 1000 Volts Current 16.0 Amperes TO-220 Features Low forward voltage drop High current capability High reliability High surge current capability Mechanical Data Cases: TO-220 molded plastic Epoxy: UL 94V-0 rate flame retardant Terminals: Leads solderable per MIL-STD202, Method 208 guaranteed Polarity: As marked High temperature soldering guaranteed: 260℃/10 seconds .16”,(4.06mm) from case. Weight: 2.24 grams PIN 1 PIN 3 Positive CT CASE PIN 2 Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol GP GP Type Number 1601 1602 Maximum Recurrent Peak Reverse Voltage 50 100 VRRM Maximum RMS Voltage 35 70 VRMS Maximum DC Blocking Voltage 50 100 VDC Maximum Average Forward Rectified Current .375”(9.5mm) Lead Length @TC = 100℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @8.0A Maximum DC Reverse Current @ TC=25℃ at Rated DC Blocking Voltage @ TC=125℃ GP GP GP GP GP Units 1603 1604 1605 1606 1607 200 140 200 400 280 400 600 420 600 800 1000 560 700 800 1000 V V V I(AV) 16.0 A IFSM 150 A VF 1.1 V 10 uA uA 250 Typical Junction Capacitance ( Note 1) Cj 50 pF Typical Thermal Resistance (Note 2) ℃/W RθJC 1.5 Operating and Storage Temperature Range TJ ,TSTG ℃ - 65 to + 150 Notes: 1. Measured at 1 MHz and Applied Reverse Voltage of 4.0 Volts D.C. 2. Thermal Resistance from Junction to Case Mounted on Heatsink size 2” x 3” x 0.25” Al-Plate IR - 558 - RATINGS AND CHARACTERISTIC CURVES (GP1601 THRU GP1607) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE FIG.2- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PER LEG 175 PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD CURRENT. (A) 18 16 14 Single Phase Half Wave 60Hz Resistive or Inductive Load 12 10 8 0 50 100 150 125 100 8.3ms Single Half Sine Wave JEDEC Method 75 50 25 0 1 150 2 5 o CASE TEMPERATURE. ( C) 20 50 100 FIG.4- TYPICAL REVERSE CHARACTERISTICS PER LEG FIG.3- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 400 100 INSTANTANEOUS REVERSE CURRENT. ( A) 100 10 1 o Tj=25 C Pulse Width=300 s 1% Duty Cycle 40 Tj=125 0C 10 4 2 1 Tj=25 0C 0.4 0.2 0.1 0.6 0.1 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0 FORWARD VOLTAGE. (V) 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.5- TYPICAL JUNCTION CAPACITANCE PER LEG 120 JUNCTION CAPACITANCE.(pF) INSTANTANEOUS FORWARD CURRENT. (A) 10 NUMBER OF CYCLES AT 60Hz 100 80 60 40 f=10MHz Vsig=50mVp-p Tj=25 0C 20 0 0.1 0.4 1 4 10 40 REVERSE VOLTAGE. (V) - 559 - 100 400 1000