SF1004G-Q1 10.0 AMPS. Glass Passivated Super Fast Rectifiers Voltage Range 200 Volts Current 10.0 Amperes TO-220 Features Low forward voltage drop High current capability High reliability High surge current capability Mechanical Data Case: Molded plastic Epoxy: UL 94V-O rate flame retardant Terminals: Leads solderable per MIL-STD202, Method 208 guaranteed Polarity: As marked High temperature soldering guaranteed: 260 oC/10 seconds .16”,(4.06mm) from case. Weight: 2.24 grams PIN 1 PIN 3 Positive CT CASE PIN 2 Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol SF1004G-Q1 Type Number Maximum Recurrent Peak Reverse Voltage 200 V RRM Maximum RMS Voltage 140 V RMS Maximum DC Blocking Voltage 200 V DC Maximum Average Forward Rectified Current .375 (9.5mm) Lead Length @T C = 100℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 5.0A @10.0A Maximum DC Reverse Current @ T A=25℃ at Rated DC Blocking Voltage @ T A=100℃ Reverse Recovery Charge(Per Diode) @IF=2A, VR≧30V,-dIF/dt=20A/uS Units V V V I(AV) 10.0 A IFSM 125 A VF 1.1 1.25 10.0 500 V uA uA 9 NC IR QS ℃/W 3.0 65 A 2S Maximum Reverse Recovery Time (Note 1) 25 nS Typical Junction Capacitance (Note 2) 10 pF Operating Temperature Range ℃ -50 to +150 Storage Temperature Range ℃ T STG -50 to +150 Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C. 3. Thermal Resistance from Junction to Case Mounted on Heatsink. Size of 2 in x 3 in x 0.25 in, Al-Plate. Thermal Resistance Junction to Case (Note 3) Rating for Fusing (t < 8.3mS) R θJC I2 t Trr Cj TJ - 268 - RATINGS AND CHARACTERISTIC CURVES (SF1004G-Q1) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 10W NONINDUCTIVE 50W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) 0 -0.25A (+) -1.0A FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE FIG.3- TYPICAL REVERSE CHARACTERISTICS 8 6 4 2 0 0 50 100 150 o PEAK FORWARD SURGE CURRENT. (A) CASE TEMPERATURE. ( C) 150 FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT TJ=100 0C 100 10 TJ=25 0C 1 TJ=125 0C 120 0.1 8.3ms Single Half Sine Wave JEDEC Method 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 90 FIG.6- TYPICAL FORWARD CHARACTERISTICS 60 100 30 0 1 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.5- TYPICAL JUNCTION CAPACITANCE 100 0 Tj=25 C 90 CAPACITANCE.(pF) SET TIME BASE FOR 5/ 10ns/ cm 1000 INSTANTANEOUS REVERSE CURRENT. ( A) 10 1cm 80 70 60 INSTANTANEOUS FORWARD CURRENT. (A) AVERAGE FORWARD CURRENT. (A) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 30 10 3 1 0.3 0.1 0.03 Tj=25oC Pulse Width=300 s 1% Duty Cycle 50 40 1 2 5 10 20 50 100 200 500 1000 REVERSE VOLTAGE. (V) - 269 - 0.01 0.4 0.6 0.8 1.0 1.2 1.4 FORWARD VOLTAGE. (V) 1.6 1.8